In Situ Polymer-Solution-Processed Graphene-PDMS Nanocomposites for Application in Intracranial Pressure Sensors.

Polydimethylsiloxane (PDMS) has emerged as a promising candidate for the dielectric layer in implantable sensors due to its exceptional biocompatibility, stability, and flexibility. This study introduces an innovative approach to produce graphene-reinforced PDMS (Gr-PDMS), where graphite powders are exfoliated into mono- and few-layer graphene sheets within the polymer solution, concurrently forming cross-linkages with PDMS. This method yields a uniformly distributed graphene within the polymer matrix with improved interfaces between graphene and PDMS, significantly reducing the percolation threshold of graphene dispersed in PDMS from 10% to 5%. As-synthesized Gr-PDMS exhibits improved mechanical and electrical properties, tested for potential use in capacitive pressure sensors. The results demonstrate an impressive pressure sensitivity up to 0.0273 kpa-1, 45 times higher than that of pristine PDMS and 2.5 times higher than the reported literature value. The Gr-PDMS showcases excellent pressure sensing ability and stability, fulfilling the requirements for implantable intracranial pressure (ICP) sensors.

Molecular Emissions from Stretched Excitation Pulse in Nanosecond Phase-Selective Laser-Induced Breakdown Spectroscopy of TiO2 Nanoaerosols.

In phase-selective laser-induced breakdown spectroscopy (PS-LIBS), gas-borne nanoparticles are irradiated with laser pulses (∼2.4 GW/cm2) resulting in breakdown of the nanoparticle phase but not the surrounding gas phase. In this work, the effect of excitation laser-pulse duration and energy on the intensity and duration of TiO2-nanoparticle PS-LIBS emission signal is investigated. Laser pulses from a frequency-doubled neodymium-doped yttrium aluminum garnet (Nd:YAG) laser (532 nm) are stretched from 8 ns (full width at half maximum, FWHM) up to ∼30 ns at fixed pulse energy using combinations of two optical cavities. The intensity of the titanium atomic emissions at around 500 nm wavelength increases by ∼60%, with the stretched pulse and emissions at around 482 nm, attributed to TiO, enhanced over 10 times. While the atomic emissions rise with the stretched laser pulse and decay around 20 ns after the end of the laser pulse, the TiO emissions reach their peak intensity at about 20 ns later and last longer. At low laser energy (i.e., 1 mJ/pulse, or 80 MW/cm2), the TiO emissions dominate, but their increase with laser energy is lower compared to the atomic emissions. The origin of the 482 nm emission is explored by examining several different aerosol setups, including Ti-O, Ti-N, and Ti-O-N from a spark particle generator and Ti-O-N-C-H aerosol from flame synthesis. The 482 nm emissions are attributed to electronically excited TiO, likely resulting from the reaction of excited titanium atoms with surrounding oxidizing (carbonaceous and/or radical) species. The effects of pulse length are attributed to the shift of absorption from the initial interaction with the particle to the prolonged interaction with the plasma through inverse bremsstrahlung.

Graphene-reinforced polymer matrix composites fabricated by in situ shear exfoliation of graphite in polymer solution: processing, rheology, microstructure, and properties.

Effective methods are needed to fabricate the next generation of high-performance graphene-reinforced polymer matrix composites (G-PMCs). In this work, a versatile and fundamental process is demonstrated to produce high-quality graphene-polymethylmethacrylate (G-PMMA) composites via in situ shear exfoliation of well-crystallized graphite particles loaded in highly-viscous liquid PMMA/acetone solutions into graphene nanoflakes using a concentric-cylinder shearing device. Unlike other methods where graphene is added externally to the polymer and mixed, our technique is a single step process where as-exfoliated graphene can bond directly with the polymer with no contamination/handling. The setup also allows for the investigation of the rheology of exfoliation and dispersion, providing process understanding in the attainment of the subsequently heat injection-molded and solidified G-PMC, essential for future manufacturing scalability, optimization, and repeatability. High PMMA/acetone concentration correlates to high mixture viscosity, which at large strain rates results in very-high shear stresses, producing a large number of mechanically-exfoliated flakes, as confirmed by liquid-phase UV-visible spectral analysis. Raman spectroscopy and other imaging evince that single- and bi-layer graphene are readily achieved. Nevertheless, a limit is reached at high mixtures viscosities where the process becomes unstable as non-Newtonian fluid behavior (e.g. viscoelastic) dominates the system. Characterization of microstructure, morphology, and properties of this new class of nanostructured composites reveals interesting trends. Observations by transmission electron microscopy, scanning electron microscopy, and helium ion microscopy of the manufactured G-PMCs show uniform distributions of unadulterated, well-bonded, discontinuous, graphene nanoflakes in a PMMA matrix, which enhances stiffness and strength via a load-transfer mechanism. Elastic modulus of 5.193 GPa and hardness of 0.265 GPa are achieved through processing at 0.7 g ml-1 of acetone/PMMA for 1% wt. starting graphite loading when injected into a sample mold at 200 °C. Mechanical properties exhibit 31% and 28.6% enhancement in elastic modulus and hardness, respectively, as measured by nano-indentation.

Modified dagger-tip Sheets glide to facilitate 2-point fixation across the anterior chamber in aniridic aphakic eyes.

Presented is a modified technique for removing a failed endothelial allograft in an aniridic aphakic eye that reduces the risk of posterior dislocation. This technique involves the creation of an artificial iris plane using a Sheets glide by trimming it into the shape of a dagger so that it can be pulled through the anterior chamber and fixated by both its passage through a paracentesis incision and the main incision. The Sheets glide then acts as a physical barrier, or scaffold, to allow safe removal of the failed endothelial allograft and subsequent repeat endothelial keratoplasty while avoiding posterior dislocation of the tissue into the vitreous cavity.

A new mouse model of ADHD for medication development.

ADHD is a major societal problem with increasing incidence and a stagnant track record for treatment advances. A lack of appropriate animal models has partly contributed to the incremental advance of this field. Hence, our goal was to generate a novel mouse model that could be useful for ADHD medication development. We reasoned that hyperactivity is a core feature of ADHD that could easily be bred into a population, but to what extent other hallmark features of ADHD would appear as correlated responses was unknown. Hence, starting from a heterogeneous population, we applied within-family selection over 16 generations to produce a High-Active line, while simultaneously maintaining an unselected line to serve as the Control. We discovered that the High-Active line demonstrated motor impulsivity in two different versions of the Go/No-go test, which was ameliorated with a low dose of amphetamine, and further displayed hypoactivation of the prefrontal cortex and dysregulated cerebellar vermal activation as indexed by c-Fos immunohistochemical staining. We conclude that the High-Active line represents a valid model for the Hyperactive-Impulsive subtype of ADHD and therefore may be used in future studies to advance our understanding of the etiology of ADHD and screen novel compounds for its treatment.

Molecular Dynamics Study of Cubic Boron Nitride Nanoparticles: Decomposition with Phase Segregation during Melting.

The relative stability and melting of cubic boron nitride (c-BN) nanoparticles of varying shapes and sizes are studied using classical molecular dynamics (MD) simulation. Focusing on the melting of octahedral c-BN nanoparticles, which consist solely of the most stable {111} facets, decomposition is observed to occur during melting, along with the formation of phase segregated boron clusters inside the c-BN nanoparticles, concurrent with vaporization of surface nitrogen atoms. To assess this MD prediction, a laser-heating experiment of c-BN powders is conducted, manifesting boron clusters for the post-treated powders. A general analysis of the geometrical and surface dependence of the nanoparticle ground-state energy using a Stillinger-Weber potential determines the relative stability of cube-shaped, octahedral, cuboctahedral, and truncated-octahedral c-BN nanoparticles. This stability is further examined using transient MD simulations of the melting behavior of the differently shaped nanoparticles, providing insights and revealing the key roles played by corner and edge initiated disorder as well as surface reconstruction from {100} to the more stable {111} facets in the melting process. Finally, the size dependence of the melting point of octahedral c-BN nanoparticles is investigated, showing the well-known qualitative trend of depression of melting temperature with decreasing size, albeit with different quantitative behavior from that predicted by existing analytical models.

The impact of maternal neglect on genetic hyperactivity.

Early environmental conditions are increasingly appreciated as critical in shaping behavior and cognition. Evidence suggests that stressful rearing environments can have an enduring impact on behaviors in adulthood, but few studies have explored the possibility that rearing environment could exacerbate genetic hyperactivity disorders. Uncovering a strong environmental influence on the transmission of hyperactivity could provide novel avenues for translational research. Recently we developed a selectively bred High-Active line of mice to model ADHD, providing a unique resource to address the question of environmental transmission. The High-Active line demonstrates transgenerational hyperactivity, but the influence of the postnatal environment (i.e. maternal care provided by dams) on hyperactivity had not been systemically quantified. This study employed a cross-fostering method to simultaneously address 1) whether High-Active and Control pups are provided with similar levels of care in the early environment, and 2) whether any differences in rearing environment influence hyperactive behavior. High-Active dams demonstrated impairment in all measures of maternal competence relative to Controls, which reduced survival rates and significantly reduced the body mass of offspring in early life and at weaning. While the deteriorated postnatal environment provided by High-Active dams was ultimately sufficient to depress Control activity, the hyperactivity of High-Active offspring remained unaffected by fostering condition. These data not only confirm the power of genetics to influence hyperactivity across generations, but also provide evidence that early rearing environments may not have a significant impact on the extreme end of hyperactive phenotypes.

Combined flame and solution synthesis of nanoscale tungsten-oxide and zinc/tin-oxide heterostructures.

Heterostructures of tungsten-oxide nanowires decorated with zinc/tin-oxide nanostructures are synthesized via a combined flame and solution synthesis approach. Vertically well-aligned tungsten-oxide nanowires are grown on a tungsten substrate by a flame synthesis method. Here, tetragonal WO(2.9) nanowires (diameters of 20-50 nm, lengths >10 µm, and coverage density of 10(9)-10(10) cm(-2)) are produced by the vapor-solid mechanism at 1720 K. Various kinds of Zn/Sn-oxide nanostructures are grown or deposited on the WO(2.9) nanowires by adjusting the Sn(2+) : Zn(2+) molar ratio in an aqueous ethylenediamine solution at 65 °C. With WO(2.9) nanowires serving as the base structures, sequential growth or deposition on them of hexagonal ZnO nanoplates, Zn(2)SnO(4) nanocubes, and SnO(2) nanoparticles are attained for Sn(2+) : Zn(2+) ratios of 0 : 1, 1 : 10, and 10 : 1, respectively, along with different saturation conditions. High-resolution transmission electron microscopy of the interfaces at the nanoheterojunctions shows abrupt interfaces for ZnO/WO(2.9) and Zn(2)SnO(4)/WO(2.9), despite lattice mismatches of >20%.

Absorption-ablation-excitation mechanism of laser-cluster interactions in a nanoaerosol system.

The absorption-ablation-excitation mechanism in laser-cluster interactions is investigated by measuring Rayleigh scattering of aerosol clusters along with atomic emission from phase-selective laser-induced breakdown spectroscopy. For 532 nm excitation, as the laser intensity increases beyond 0.16 GW/cm^{2}, the scattering cross section of TiO_{2} clusters begins to decrease, concurrent with the onset of atomic emission of Ti, indicating a scattering-to-ablation transition and the formation of nanoplasmas. With 1064 nm laser excitation, the atomic emissions are more than one order of magnitude weaker than that at 532 nm, indicating that the thermal effect is not the main mechanism. To better clarify the process, time-resolved measurements of scattering signals are examined for different excitation laser intensities. For increasing laser intensity, the cross section of clusters decreases during a single pulse, evincing the shorter ablation delay time and larger ratios of ablation clusters. Assessment of the electron energy distribution during the ablation process is conducted by nondimensionalizing the Fokker-Planck equation, with analogous Strouhal Sl_{E}, Peclet Pe_{E}, and Damköhler Da_{E} numbers defined to characterize the laser-induced aerothermochemical environment. For conditions where Sl_{E}≫1, Pe_{E}≫1, and Da_{E}≪1, the electrons are excited to the conduction band by two-photon absorption, then relax to the bottom of the conduction band by electron energy loss to the lattice, and finally serve as the energy transfer media between laser field and lattice. The relationship between delay time and excitation intensity is well correlated by this simplified model with quasisteady assumption.

Combined flame and electrodeposition synthesis of energetic coaxial tungsten-oxide/aluminum nanowire arrays.

A nanostructured thermite composite comprising an array of tungsten-oxide (WO2.9) nanowires (diameters of 20-50 nm and lengths of >10 µm) coated with single-crystal aluminum (thickness of ~16 nm) has been fabricated. The method involves combined flame synthesis of tungsten-oxide nanowires and ionic-liquid electrodeposition of aluminum. The geometry not only presents an avenue to tailor heat-release characteristics due to anisotropic arrangement of fuel and oxidizer but also eliminates or minimizes the presence of an interfacial Al2O3 passivation layer. Upon ignition, the energetic nanocomposite exhibits strong exothermicity, thereby being useful for fundamental study of aluminothermic reactions as well as enhancing combustion characteristics.

Genomic and nongenomic signaling induced by 1α,25(OH)2-vitamin D3 promotes the recovery of amyloid-ß phagocytosis by Alzheimer's disease macrophages.

Brain clearance of amyloid-ß (Aß42) by innate immune cells is necessary for maintenance of normal brain function. Phagocytosis of soluble Aß42 by Alzheimer's disease (AD) macrophages is defective, recovered in all "Type I and Type II" AD patients by 1α,25(OH)2-vitamin D3 (1,25D3) and blocked by the nuclear vitamin D receptor (VDR) antagonist (23S)-25-dehydro-1α(OH)-vitamin D3-26,23-lactone (MK). Bisdemethoxycurcumin (BDC) is a VDR ligand and additive with 1,25D3 in promoting Aß42 phagocytosis by Type I, but not by Type II macrophages. Here, we define the following intracellular mechanisms regulated by 1,25D3 that are associated with recovery of phagocytosis and consistent with the selectivity of BDC: 1) 1,25D3 potentiates a 4,4-diisothiocyanostilbene-2,2-disulfonic acid-sensitive chloride channel (i.e., ClC-3) currents in both Type I and II AD macrophages, but curcumin only potentiates the currents in Type I cells; 2) 1,25D3 is particularly effective in upregulating ClC-3 mRNA expression in Type II peripheral blood mononuclear cells (PBMCs) while both 1,25D3 and the BDC analog, C180, upregulate VDR mRNA, repressed by Aß42 in Type II PBMCs; and 3) 1,25D3-induced Aß42 phagocytosis is attenuated by the calcium-dependent ClC-3 blocker, inositol 3,4,5,6-tetraphosphate (IP4), in both AD Types and by the MEK1/2 inhibitor U0126 only in Type II macrophages. VDR hydrogen/deuterium exchange coupled mass spectrometry and computational results show differences between the abilities of 1,25D3 and curcuminoids to stabilize VDR helices associated with the regulation of gene transcription. The structure-function results provide evidence that 1,25D3 activation of VDR-dependent genomic and nongenomic signaling, work in concert to recover dysregulated innate immune function in AD.

Role of dipole-dipole interaction on enhancing Brownian coagulation of charge-neutral nanoparticles in the free molecular regime.

In contrast to van der Waals (vdW) forces, Coulombic dipolar forces may play a significant role in the coagulation of nanoparticles (NPs) but has received little or no attention. In this work, the effect of dipole-dipole interaction on the enhancement of the coagulation of two spherically shaped charge-neutral TiO(2) NPs, in the free molecular regime, is studied using classical molecular dynamics (MD) simulation. The enhancement factor is evaluated by determining the critical capture radius of two approaching NPs for different cases of initial dipole direction with respect to path (parallel∕perpendicular) and orientation with respect to each other (co-orientated∕counterorientated). As particle diameter decreases, the enhancement of coagulation is augmented as the ratio of dipole-dipole force to vdW force becomes larger. For 2-nm TiO(2) NPs at 273 K, the MD simulation predicts an average enhancement factor of about 8.59, which is much greater than the value of 3.78 when only the vdW force is considered. Nevertheless, as temperature increases, the enhancement factor due to dipole-dipole interaction drops quickly because the time-averaged dipole moment becomes small due to increased thermal fluctuations (in both magnitude and direction) of the instantaneous dipole moment.

IL-17A is increased in the serum and in spinal cord CD8 and mast cells of ALS patients.

The contribution of inflammation to neurodegenerative diseases is increasingly recognized, but the role of inflammation in sporadic amyotrophic lateral sclerosis (sALS) is not well understood and no animal model is available. We used enzyme-linked immunosorbent assays (ELISAs) to measure the cytokine interleukin-17A (IL-17A) in the serum of ALS patients (n = 32; 28 sporadic ALS (sALS) and 4 familial ALS (fALS)) and control subjects (n = 14; 10 healthy subjects and 4 with autoimmune disorders). IL-17A serum concentrations were 5767 ± 2700 pg/ml (mean ± SEM) in sALS patients and 937 ± 927 pg/ml in fALS patients in comparison to 7 ± 2 pg/ml in control subjects without autoimmune disorders (p = 0.008 ALS patients vs. control subjects by Mann-Whitney test). Sixty-four percent of patients and no control subjects had IL-17A serum concentrations > 50 pg/ml (p = 0.003 ALS patients vs. healthy subjects by Fisher's exact test). The spinal cords of sALS (n = 8), but not control subjects (n = 4), were infiltrated by interleukin-1ß- (IL-1ß-), and tumor necrosis factor-α-positive macrophages (co-localizing with neurons), IL-17A-positive CD8 cells, and IL-17A-positive mast cells. Mononuclear cells treated with aggregated forms of wild type superoxide dismutase-1 (SOD-1) showed induction of the cytokines IL-1ß, interleukin-6 (IL-6), and interleukin-23 (IL-23) that may be responsible for induction of IL-17A. In a microarray analysis of 28,869 genes, stimulation of peripheral blood mononuclear cells by mutant superoxide dismutase-1 induced four-fold higher transcripts of interleukin-1α (IL-1α), IL-6, CCL20, matrix metallopeptidase 1, and tissue factor pathway inhibitor 2 in mononuclear cells of patients as compared to controls, whereas the anti-inflammatory cytokine interleukin-10 (IL-10) was increased in mononuclear cells of control subjects. Aggregated wild type SOD-1 in sALS neurons could induce in mononuclear cells the cytokines inducing chronic inflammation in sALS spinal cord, in particular IL-6 and IL-17A, damaging neurons. Immune modulation of chronic inflammation may be a new approach to sALS.