Annual variation of source contributions to PM10 and oxidative potential in a mountainous area with traffic, biomass burning, cement-plant and biogenic influences.

Toxicity of particulate matter (PM) depends on its sources, size and composition. We identified PM10 sources and determined their contribution to oxidative potential (OP) as a health proxy for PM exposure in an Alpine valley influenced by cement industry. PM10 filter sample chemical analysis and equivalent black carbon (eBC) were measured at an urban background site from November 2020 to November 2021. Using an optimized Positive Matrix Factorization (PMF) model, the source chemical fingerprints and contributions to PM10 were determined. The OP assessed through two assays, ascorbic acid (AA) and dithiothreitol (DTT), was attributed to the PM sources from the PMF model with a multiple linear regression (MLR) model. Ten factors were found at the site, including biomass burning (34, 40 and 38% contribution to annual PM10, OPAA and OPDDT, respectively), traffic (14, 19 and 7%), nitrate- and sulphate-rich (together: 16, 5 and 8%), aged sea salt (2, 2 and 0%) and mineral dust (10, 12 and 17%). The introduction of innovative organic tracers allowed the quantification of the PM primary and secondary biogenic fractions (together: 13, 8 and 21%). In addition, two unusual factors due to local features, a chloride-rich factor and a second mineral dust-rich factor (named the cement dust factor) were found, contributing together 10, 14 and 8%. We associate these two factors to different processes in the cement plant. Despite their rather low contribution to PM10 mass, these sources have one of the highest OPs per µg of source. The results of the study provide vital information about the influence of particular sources on PM10 and OP in complex environments and are thus useful for PM control strategies and actions.

Size distribution of black (BC) and total carbon (TC) in Vienna and Ljubljana.

During two campaigns in winter 2004, size segregated impactor samples (0.1-10 microm) and filter samples were taken in two Central European cities (Vienna, Austria and Ljubljana, Slovenia). The impactor samples were analyzed for major inorganic ions and short-chain organic acids, total carbon (TC) and black carbon (BC). Maximum concentrations of total mass were 71.6 microg m(-3) in Vienna and 73.1 microg m(-3) in Ljubljana. Minimum concentrations in Vienna were only half those in Ljubljana. The BC content of the aerosol was similar (ca. 8%), but the BC/TC ratio was higher in Vienna than in Ljubljana (0.39 vs. 0.29), reflecting the different contribution of diesel traffic emissions. The mass median diameters of the submicron size distributions of all major fractions (total mass, TC, BC and SO(4)(2-)) were smaller in Vienna (0.43 microm, 0.41 microm, 0.38 microm and 0.48 microm, respectively) than in Ljubljana (0.55 microm, 0.44 microm, 0.42 microm and 0.60 microm, respectively). Impactor/filter ratios for total mass were 0.79 in Vienna and 0.82 in Ljubljana, while the ratios for BC were 0.56 in Vienna and 0.49 in Ljubljana. An estimation of the mixing state of accumulation mode BC indicated that 33% and 37% of BC, respectively, are mixed externally to the aerosol in the accumulation size range in Vienna and Ljubljana.

Ion-exchange-based eluent-free preconcentration of some anions.

Preconcentration procedures based on ion-exchange methods are often used to enhance the sensitivities of analytical techniques where the eluent used for eluting the preconcentrated ions does not influence the subsequent analytical step. Until recently, only a limited use of ion-exchange-based sample preconcentration procedures has been found in those analytical techniques where the eluent components strongly influence the separation procedure [e.g., capillary electrophoresis (CE)]. In this paper, we present a preconcentration procedure based on (i) the preconcentration of anions on an ion-exchange resin, (ii) the subsequent elution of analytes, and (iii) on-line removal of eluent components by chemical suppression using an appropriate suppressor device (either packed-bed suppressor column or micromembrane suppressor). The adjustment of the system parameters, combined with a computer-controlled, sensing/switching system, resulted in a minimal additional dilution of the eluted preconcentrated anions. The efficiency of the proposed enrichment/matrix removal procedure was tested by using off-line CE analysis of collected preconcentrated samples, reaching a LOD of 1 microg/l for a selected anion.