A Lateral Fracture Line Affects Femoral Trochanteric Fracture Instability and Swing Motion of the Intramedullary Nail: A Biomechanical Study.

Background: An unstable trochanteric femoral fracture is a serious injury, with a 1-year mortality rate of 5.4% to 24.9%, for which there is currently no standard treatment method. The lag screw insertion site is one of the primary contact areas between the cortical bone and an intramedullary nail. We hypothesized that a posterolateral fracture causes intramedullary nail instability when the posterolateral fracture line interferes with lag screw insertion. The purpose of the present study was to investigate the effect of posterolateral fracture line morphology on intramedullary nail stability by simulating unstable trochanteric femoral fractures with a posterolateral fracture fragment. Methods: Eighteen custom-made synthetic osteoporotic bone samples were used in the present study. Nine samples had a posterolateral fracture line interfering with the lag screw insertion hole (Fracture A), and the other 9 had a fracture line 10 mm away from the hole (Fracture B). Cyclic loading (750 N) was applied to the femoral head 1,500 times. Movement of the end cap attached to the intramedullary nail was recorded. The amplitudes of motion in the coronal plane (coronal swing motion), sagittal plane (sagittal swing motion), and axial plane (total swing motion) were evaluated. The change in the neck-shaft angle was evaluated on photographs that were made before and after the test. Medial cortical displacement was measured before and after the test. Results: Two Fracture-A samples were excluded because the amplitude of sagittal swing motion was too large. The mean values for coronal, sagittal, and total swing motion were 1.13 ± 0.28 mm and 0.51 ± 0.09 mm (p < 0.001), 0.50 ± 0.12 mm and 0.46 ± 0.09 mm (p = 0.46), and 1.24 ± 0.24 mm and 0.69 ± 0.11 mm (p < 0.001) for Fractures A and B, respectively. The mean neck-shaft angle change was -8.29° ± 2.69° and -3.56° ± 2.35° for Fractures A and B, respectively (p = 0.002). The mean displacement of the medial cortex was 0.38 ± 1.12 mm and 0.12 ± 0.37 mm for Fractures A and B, respectively (p = 0.57). Conclusions: This study showed that an unstable trochanteric femoral fracture with a posterolateral fracture line that interferes with the lag screw insertion holes is a risk factor for increased intramedullary nail instability.

Endosteal strut using a hydroxyapatite/poly-L-lactide mesh tube with a proximal humeral locking plate for the treatment of proximal humeral fractures.

PURPOSE: Proximal humeral fractures cause large intramedullary bone defects after humeral-head reduction. Hydroxyapatite/poly-L-lactide (HA/PLLA) materials are widely used for various fractures. However, the efficacy of endosteal strut using a HA/PLLA mesh tube (ES-HA/PLLA) with a locking plate for treating proximal humeral fractures was not reported. The purpose of this study is to examine the efficacy of ES-HA/PLLA with a proximal humeral locking plate in proximal humeral fractures. METHODS: Seventeen patients with proximal humeral fractures treated using ES-HA/PLLA with a locking plate from November 2017 to November 2021 were evaluated. The range of motion of the shoulder and postoperative complications were assessed at the final follow-up. Radiographs were evaluated to assess bone union and loss of reduction by measuring humeral-head height (HHH) and humeral neck-shaft angle (NSA). RESULTS: The average flexion and external rotation of the shoulder at the final follow-up were 137° (range, 90-180°) and 39° (range, - 10 to 60°), respectively. All fractures were united. The average HHH and NSA just after the surgery and final follow-up were 12.5 mm and 11.6 mm and 129.9° and 127.4°, respectively. Two patients presented screw perforation of the humeral head. One patient underwent implant removal due to infection. Avascular necrosis of the humeral head was observed in one patient with arthritis mutilans. CONCLUSIONS: The use of ES-HA/PLLA with a proximal humeral locking plate resulted in bone union in all patients and prevented postoperative loss of reduction. ES-HA/PLLA is one of the treatment options for proximal humeral fractures.

Outcomes of spring-locking plate fixation method using locking mesh plate/box plate for posterior wall fractures of the acetabulum: a retrospective single-centre study.

INTRODUCTION: This retrospective study evaluated the outcomes of variable-angle locking compression plate, mesh plate, or footplate box fixation for posterior acetabular wall fractures. PATIENTS AND METHODS: The study included nine patients with unstable posterior acetabular wall fractures who underwent internal fixation with the "spring-locking plate fixation method" between January 2015 and December 2019. Patient demographics, fracture classifications, surgical details, radiological and clinical evaluations, and complications were collected from electronic medical records. Statistical analyses were performed to assess the relationship between preoperative and postoperative dislocations. RESULTS: The mean age of the patients was 46 years, and the majority were men (88.9%). Fracture types included posterior wall fractures and posterior column plus posterior wall fractures. The mean operative time was 246 min and the mean blood loss was 663 mL. The surgical approaches included the Kocher-Langenbeck, Ganz trochanteric flip, and transtrochanteric approaches. Variable-angle locking compression plate mesh plates and footplate box type implants were used for fixation. The mean preoperative dislocation was 23 mm, which was significantly reduced to 1 mm immediately post-operation and at the final observation. The bone fusion rate was 100% and radiological and clinical evaluations revealed favourable outcomes. Complications were minimal, with mild heterotopic ossification observed in four patients. CONCLUSION: The spring-locking plate fixation method demonstrated satisfactory outcomes for the treatment of posterior acetabular wall fractures. This technique provides rigid fixation. Furthermore, the use of variable-angle locking screws minimizes the risk of intra-articular perforations. Despite limitations such as a small sample size and the absence of a control group, the results suggest that the spring-locking plate fixation method may be valuable in managing these fractures.

Levodopa-Carbidopa Intestinal Gel Injection for Patient with Severe Parkinson's Disease Followed by Total Hip Arthroplasty: A Case Report and Literature Review.

BACKGROUND: Patients with Parkinson's disease have a high dislocation rate after total hip arthroplasty (THA). This study describes a case with severe Parkinson's disease who developed rapidly destructive coxarthrosis (RDC) and underwent THA using a dual mobility cup after a levodopa-carbidopa intestinal gel (LCIG) infusion. CASE PRESENTATION: The patient is a 59-year-old female with a ten-year history of Parkinson's disease, which was first treated with oral levodopa. The patient developed RDC of the right hip joint. However, THA was difficult owing to Parkinson's disease and its treatment side effects, such as wearing-off, dyskinesia, and freezing of the gait, Thus, LCIG was initiated, and improvement in wearing-off and dyskinesia was observed. Two months after the LCIG therapy, the disease was controlled well. THA was subsequently performed using a dual mobility cup to prevent postoperative dislocation. Postoperatively, LCIG therapy was continuously administered to carefully manage the disease, which was controlled well with no increase in wearing-off and dyskinesia after surgery. At 1 year after surgery, the walking speed, stride length, and the Harris hip score improved compared to preoperatively. The UPDRS III motor score improved to eight without signs of wearing-off or dyskinesia. The Hoehn-Yahr scale was II in the "on" period and remained unchanged 1 year after surgery. The patient could walk without a cane and had satisfactory functional outcomes. CONCLUSION: This case proved that LCIG treatment performed preoperatively, followed by THA using a dual mobility cup, and strict management of Parkinson's disease could result in a satisfactory clinical course without recurrence of wearing-off and dyskinesia. Similar procedures may benefit other patients with Parkinson's disease who have previously been deemed unsuitable for THA.

Nontuberculous mycobacteriosis oligoarthritis of the right hand misdiagnosed as rheumatoid arthritis: A case report.

Infection with Mycobacterium marinum has several different clinical presentations. Most commonly, it appears as a solitary papulonodular lesion on an extremity. A rare presentation of osteoarticular M. marinum involving multiple small joints and tenosynovitis of the hand, which was misdiagnosed as rheumatoid arthritis, is reported. The patient was initially treated for seronegative rheumatoid arthritis but failed to respond to methotrexate. Magnetic resonance imaging showed arthritis and tenosynovitis. Subsequently, synovial biopsy led to histological and microbiological diagnosis. Antimycobacterial treatment should be started promptly in such cases. The combined use of rifampicin, ethambutol, and clarithromycin appears to be effective, and debridement is indicated in patients with deep-seated infections.

A biomechanical analysis of the effect of hydroxyapatite augmentation for trochanteric femoral fractures.

Hydroxyapatite (HA) augments are used to treat trochanteric femoral fractures. However, the efficacy of HA augmentation has not been fully described in trochanteric femoral fracture surgery. In total, 85 patients were enrolled in the present study; all had trochanteric femoral fractures between January 2016 and October 2020, 45 with HA (HA group) and 40 without HA (N group). The intraoperative lag screw insertion torque was directly measured and the amount of lag screw telescoping with and without HA augmentation after surgery was analyzed. Maximum lag screw insertion torque (max-torque), bone mineral density in the opposite femoral neck (n-BMD), tip apex distance (TAD) of the lag screw, radiographic findings including fracture union, the amounts of lag screw telescoping and occurrence of complications were evaluated. A total of 12 patients were excluded if they were aged under 60 years old, had ipsilateral surgery and disorders in the hip joint, TAD of the lag screw ≥26 mm on postoperative radiographs and had measurement errors. A total of 73 fractures could be analyzed: HA group (n=36) and N group (n=37). Max-torque/n-BMD ratios were higher in the HA group compared with in the N group (7.23±2.71 vs. 5.93±1.91 g/cm2·N·m; P=0.04). The amounts of lag screw telescoping in the HA group were smaller compared with the N group (1.41±2.00 vs. 2.58±2.34; P=0.05). Evaluation of screw insertion torque showed maximum screw insertion torque correlated well with n-BMD in both groups, HA (R=0.57; P<0.01) and N group (R=0.64; P<0.01). No correlation was found between maximum screw insertion torque and TAD in both groups, HA (R=-0.10; P=0.62) and N group (R=0.02; P=0.93). All fractures were radiographically united without any complications. These results support the effectiveness of HA augmentation, indicating higher resistance against rotational instability and reduced lag screw telescoping in trochanteric femoral fracture treatment.

Median Nerve Recovery and Morphological Change on MRI at 24 Months after Open Carpal Tunnel Release.

Background: This study aimed to investigate the relationship between postoperative clinical results and long-term morphological changes in patients with carpal tunnel syndrome (CTS) as observed on magnetic resonance imaging (MRI) before and after open carpal tunnel release (OCTR). Methods: We retrospectively analysed data for 28 hands that had undergone OCTR with at least 24 months of follow-up data. Two-point discrimination (2PD) test results were examined for the first three fingers, as were the distal motor latency (DML) and sensory conduction velocity (SCV) of the median nerve. We also calculated the cross-sectional area (CSA) of the carpal tunnel and the distance from the median nerve to the volar carpal bone at the hamate and the pisiform levels using MRI images. Variables were compared before and 24 months after OCTR. Results: Significant improvements in all variables were observed, including average 2PD scores (Finger I: 13.1 ± 6.2 vs. 7.7 ± 4.3, p < 0.01, Finger II: 11.9 ± 6.6 vs. 7.0 ± 3.5, p < 0.01, Finger III: 13.6 ± 6.1 vs. 7.8 ± 4.5, p < 0.01), average DML (8.3 ± 3.3 vs. 4.3 ± 0.6 m/s, p < 0.01), average SCV (30.8 ± 11.0 vs. 41.3 ± 5.3 m/s, p < 0.01), CSA of the carpal tunnel (hamate level: 194.9 ± 30.6 vs. 254.2 ± 47.6 mm2, p < 0.01, pisiform level: 244.2 ± 46.5 vs. 274.7 ± 75.1 mm2, p = 0.01) and the distance between the median nerve and volar carpal bone (hamate level: 8.7 ± 1.4 vs. 11.2 ± 1.6 mm, p < 0.01, pisiform level: 11.8 ± 1.7 vs. 13.8 ± 2.5 mm, p < 0.01). Conclusions: Our results demonstrate that OCTR is successful in achieving long-term decompression and recovery of the median nerve in patients with CTS. Level of Evidence: Level III (Therapeutic).

Fixation of intra-articular calcaneal fractures: A comparative study of the postoperative outcome between HA/PPLA screws and locking plates.

Background: Forged unsintered hydroxyapatite and poly l-lactic acid (F-u-HA/PLLA) screw is bioactivite, bioabsorbable, and radiopaque with high mechanical strength. Its efficacy has been previously demonstrated in the treatment of lateral humeral condylar, lateral tibial condylar, ankle, and patellar fractures. However, studies on its efficacy in treatment of calcaneal fractures is lacking. This study aimed to compare the postoperative results of F-u-HA/PLLA screw fixation and locking plate fixation for intra-articular calcaneal fractures. Methods: From January 2013 to December 2019, 47 closed intra-articular fractures treated with either F-u-HA/PLLA screws (group S, 18 feet in 17 patients) or locking plates (group P, 29 feet in 28 patients) in a single trauma center were retrospectively reviewed. The sinus tarsi approach was used in both groups. The time to bone union, step-off, varus deformity, Bohler's angle, and width and height of the calcaneus were assessed after surgery. Ankle joint range of motion (ROM) and postoperative complications were also assessed. Results: All fractures were successfully treated. The Kaplan-Meier curves of the two groups showed similar trends. The log-rank test showed no significant difference in the time to bone union between the two groups (p = 0.48). In the Cox proportional hazards model adjusted for preoperative width and Bohler's angle, the hazard ratio for bone union was not statistically significant (HR: 1.13, 95%CI: 0.50-2.56, p = 0.78). Other variables included step-off (group S: 2.0 vs group P: 2.2 mm, p = 0.84), varus deformity (2.0° vs. 3.0°, p = 0.7), Gissane's angle (103.5° vs 104.0°, p = 0.84), width (38.0 vs 34.8 mm, p = 0.12), height (42.1 vs 44.0 mm, p = 0.07), and ankle ROM degrees (dorsal flexion, 20.0° vs. 20.0°, p = 0.13; plantar flexion 40.0° vs 40.0°, p = 0.56), which were not significantly different between groups P and S. The Bohler's angle was smaller in group S than in group P (20.5° vs 27.0°, p < 0.01). No skin necrosis or infection was observed in either group. Conclusion: Postoperative results of F-u-HA/PLLA screw fixation using the sinus tarsi approach for intra-articular calcaneal fractures were as good as those of locking plate fixation.

Pin and Wire System Fixation for the Treatment of Comminuted Patella Fractures.

We describe the wiring technique and evaluate the radiographic and clinical outcomes of treatment with a pin and wire system (PWS) for comminuted patella fractures. From June 2013 to October 2018, 33 patients with comminuted patella fractures were treated using a PWS. Open reduction and internal fixation was performed with multiple pins and a wire. All patients were allowed full weight bearing without a brace. Radiographs were obtained to evaluate bone union, implant breakage, back-out of pins, and intra-articular gaps and step-off. Clinical outcomes and postoperative complications were assessed at final follow-up examination. All fractures were united. Thirteen cable wires in 13 patients were partially broken without displacement of fracture at an average of 7.4 months (range, 1-19 months) postoperatively. The average preoperative, postoperative, and final follow-up intra-articular gap and step-off were 11.7 mm, 0.5 mm, and 0.03 mm and 6.6 mm, 0.4 mm, and 0.2 mm, respectively. The average postoperative pin displacement was 0.1 mm (range, 0-0.8 mm). Deep infection was not observed after the surgery. The implant removal rate was 21% (7 of 33). Among these, the symptomatic implant removal rate was 9% (3 of 33). Additionally, 3 of 7 patients with implant removal had broken wires. The average flexion and extension of knee joints were 139.7° (range, 120°-150°) and -0.9° (range, -10° to 0°), respectively. A PWS prevents back-out of the pins and reduces intra-articular gaps and step-off distances to acceptable levels, even if the cable wire is partially broken. Therefore, a PWS is a good treatment option for comminuted patella fractures. [Orthopedics. 2023;46(5):291-296.].

Clinical and radiographic outcomes of primary total hip arthroplasty with the revelation hip system using density mapping.

The Revelation Hip System is a cementless stem with a lateral flare concept. Stable fixation is achieved by fitting the stem to the medullary cavity of the proximal lateral femoral cortex. Patients who have undergone total hip arthroplasty using the Revelation Hip System show good postoperative clinical and radiographic outcomes. However, to the best of our knowledge, no study has reported the relationship between stem fitting and clinical or radiological outcomes after the surgery. In the present study, we investigated the relationship between stem fitting and clinical or radiological outcomes after total hip arthroplasty (THA) using the Revelation Hip System. In this study, 28 hips of 26 patients who were treated with the Revelation Hip System for osteoarthritis, osteonecrosis of the femoral head, rheumatoid arthritis, and rapidly destructive coxarthropathy and were followed up for > 5 y were enrolled. These patients were divided into two groups, including the rest fit group (11 hips, group R) and the control group (17 hips, group C), according to the results of the density mapping analysis. In group R, the lateral side of the stem fits on the medullary cavity of the proximal lateral femoral cortex, while in group C, the lateral side of the stem did not fit. Radiographic results showed no significant differences between the groups in terms of stem alignment, subsidence, and stress shielding around the cup. The incidence of stress shielding around the stem in zone 7 was not significant but tended to be higher in group R than in group C (p = 0.052). Clinical outcomes showed no significant differences between group R and group C in terms of the Harris hip score, the Japanese Orthopaedic Association (JOA) score, and the Japanese Orthopaedic Association Hip Disease Evaluation Questionnaire (JHEQ) total score. However, pain complaints that were assessed by patient-reported outcomes using the 36-Item Short Form Health Survey (SF-36) bodily pain and vitality subscales and the JHEQ pain subscale were significantly higher in group R than in group C at the final follow-up. These results suggest that some patients had pain complaint even if the stems were inserted as per the concept after THA with the Revelation Hip System.Trial Registration911.

The finger-to-nose test improved diagnosis of cerebrovascular events in patients presenting with isolated dizziness in the emergency department.

It is difficult to identify patients with isolated dizziness caused by cerebrovascular events. The estimated risk of cerebrovascular events in isolated dizziness patients is not completely understood. We aimed to evaluate the association of the finger-to-nose test (FNT) in diagnosing cerebrovascular events in isolated dizziness patients in emergency departments (EDs). We combined 2 datasets from a single center for consecutive isolated dizziness patients, with the same inclusion and exclusion criteria. Those who met any of the following criteria were excluded: no FNT data, age < 16 years, and psychological trauma. The primary outcome was cerebrovascular event, which was defined as cerebral stroke due to cerebral infarction, cerebral hemorrhage, vertebral artery dissection, or transient ischemic attack. In the combined dataset, there were 357 patients complaining of isolated dizziness and 31 cerebrovascular events. After adjusted by 5 previously reported risk factors for cerebrovascular event, (age, hypertension, hyperlipidemia, diabetes mellitus, nystagmus), a multivariable logistic model analysis showed that the existence of FNT abnormalities was significantly associated with cerebrovascular events (odds ratio, 25.3; 95% confidence interval, 7.3-88.2; p < 0.001). There was a significant increase in predictive accuracy, with an AUC increase of 0.116 in the in a ROC analysis (p = 0.023). The existence of FNT abnormalities is considered as a strong risk factor that could be useful for predicting cerebrovascular events in isolated dizziness patients. We recommend the FNT for screening isolated dizziness patients in EDs to judge whether they need to undergo further diagnostic evaluation.

Evaluation of lower extremity gait analysis using Kinect V2® tracking system.

INTRODUCTION: Microsoft Kinect V2® (Kinect) is a peripheral device of Xbox® and acquires information such as depth, posture, and skeleton definition. In this study, we investigated whether Kinect can be used for human gait analysis. METHODS: Ten healthy volunteers walked 20 trials, and each walk was recorded by a Kinect and infrared- and marker-based-motion capture system. Pearson's correlation and overall agreement with a method of meta-analysis of Pearson's correlation coefficient were used to assess the reliability of each parameter, including gait velocity, gait cycle time, step length, hip and knee joint angle, ground contact time of foot, and max ankle velocity. Hip and knee angles in one gait cycle were calculated in Kinect and motion capture groups. RESULTS: The coefficients of correlation for gait velocity (r = 0.92), step length (r = 0.81) were regarded as strong reliability. Gait cycle time (r = 0.65), minimum flexion angle of hip joint (r = 0.68) were regarded as moderate reliability. The maximum flexion angle of the hip joint (r = 0.43) and maximum flexion angle of the knee joint (r = 0.54) were regarded as fair reliability. Minimum flexion angle of knee joint (r = 0.23), ground contact time of foot (r = 0.23), and maximum ankle velocity (r = 0.22) were regarded as poor reliability. The method of meta-analysis revealed that participants with small hip and knee flexion angles tended to have poor correlations in maximum flexion angle of hip and knee joints. Similar trajectories of hip and knee angles were observed in Kinect and motion capture groups. CONCLUSIONS: Our results strongly suggest that Kinect could be a reliable device for evaluating gait parameters, including gait velocity, gait cycle time, step length, minimum flexion angle of the hip joint, and maximum flexion angle of the knee joint.

Effect of hydroxyapatite tubes on the lag screw intraoperative insertion torque for the treatment of intertrochanteric femoral fractures.

BACKGROUND: Hydroxyapatite (HA) augments are frequently used in orthopedic surgery. However, the effectiveness of HA augments on the treatment of intertrochanteric femoral fractures remains unknown. This study aimed to investigate whether the use of HA tubes affects the intraoperative insertion torque of the lag screw during intertrochanteric femoral fracture surgery. METHODS: From January 2016 to October 2020, 58 patients with intertrochanteric femoral fractures were included and divided into the HA treatment group (HA group, n = 29) and non-HA treatment group (N group, n = 29). Patients with intertrochanteric femoral fractures were treated using the Gamma3 nail system® with or without two HA tubes. HA tubes were inserted into the femoral head through the lag screw hole before the insertion of the lag screw. The mean and maximum intraoperative insertion torques of the lag screw, bone mineral density (BMD) of the uninjured opposite side femoral neck, and tip apex distance (TAD) of the lag screw on postoperative radiographs were assessed. To assess the loss of reduction after the surgery, we investigated the amounts of telescoping of the lag screw and the changes in the neck shaft angle. RESULTS: The mean and maximum insertion torques were correlated with BMD in the HA and N groups, respectively. The mean and maximum insertion torques were not correlated with TAD in the HA and N groups, respectively. The mean torque/BMD ratio was significantly higher in the HA group than in the N group (p = 0.03). There were no significant differences in the maximum torque/BMD ratio between HA and N groups (p = 0.06), while the maximum torque/BMD ratio tended to be higher in the HA group than in the N group. The amounts of telescoping of the lag screw in the HA group were significantly lower than that in the N group (p = 0.04), while there were no significant differences in the changes in the neck shaft angle between two groups (p = 0.32). CONCLUSION: Our results strongly suggest that the use of HA tubes increases the intraoperative lag screw insertion torque/BMD ratio and may improve the lag screw fixation by strengthening the bone/metal thread interface in the treatment of intertrochanteric femoral fractures.

Banding with lesser trochanter fragment using nonabsorbable tape in trochanteric femoral fractures.

INTRODUCTION: Trochanteric femoral fracture is one of the most common fractures in the elderly. Trochanteric femoral fracture with involvement of the lesser trochanter is considered unstable and recognized as having a poor prognosis. However, fixation of lesser trochanter fragment is scarce because of technical difficulties. In this study, we reported the simple surgical procedure and the effect of using nonabsorbable tape in lesser trochanter fixation. METHODS: From January 2014 to December 2017, 114 patients treated with proximal intramedullary nailing for trochanteric fractures with the lesser trochanter fragment were reviewed. Among patients enrolled in this study, 73 were followed up until radiographic bone union, of which 26 were treated with lesser trochanter fragment banding (group B) and 47 without banding (group N). Radiographs and/or computed tomography images were used to evaluate bone union of the lesser trochanter fragment at three months postoperatively. RESULTS: The bone union of the lesser trochanter fragment was achieved in 24 cases (92%) in group B and 30 cases (64%) in group N. Compared with group N, group B showed a significantly increased number of mild and moderate deformities but decreased number of severe deformity and nonunion (P < 0.001). Postoperative complications were not observed in both groups. CONCLUSIONS: From the viewpoint of increasing lesser trochanteric bone union ratio, fixation of the lesser trochanter fragment using nonabsorbable tape in the treatment of trochanteric fractures could be an effective procedure.

Treatment of patellar fractures using bioresorbable forged composites of raw particulate unsintered hydroxyapatite/poly-L-lactide cannulated screws and nonabsorbable sutures.

BACKGROUND: Forged composites of raw particulate unsintered hydroxyapatite/poly-L-lactide (F-u-HA/PLLA) implants are widely used in surgeries because they possess high mechanical strength, bioactivity, and radio-opacity. We previously reported that F-u-HA/PLLA implants were useful for treating lateral tibial condylar, lateral humeral condylar, and ankle fractures. The study aim was to investigate the efficacy of F-u-HA/PLLA cannulated screws and FiberLoop® for treating transverse patellar fractures. METHODS: From April 2013 to February 2019, 15 patients with transverse patellar fractures were treated with F-u-HA/PLLA cannulated screws and FiberLoop® as follows: Open reduction and internal fixation (ORIF) were performed with two F-u-HA/PLLA cannulated screws and a temporary fixation Kirshner wire (K-wire). Three No. 2 FiberLoops® were inserted into these two screw holes and the K-wire hole for temporary fixation. All patients were allowed to full weight-bearing gaits using a knee brace. Knee range of motion exercise was initiated on postoperative day 1. Knee flexion was restricted to ≤90° for 1 month postoperatively. Radiograph was performed to evaluate fracture healing, screw breakage, reduction loss, and screw radio-opacity. Clinical outcomes and postoperative complications were assessed. RESULTS: The average follow-up was 16.0 months. All fractures were successfully united. Screw breakage, reduction loss, osteolysis, and radiolucent zones around the screws were not observed at the final radiographic follow-up. All F-u-HA/PLLA screw shadows were observed during the follow-up. The average range of flexion and extension were 132.0° and -2.7°, respectively. No patients experienced deep infection episodes, late aseptic tissue reactions, or foreign body reactions postoperatively. No patients complained of pain at the final follow-up. All patients returned to their pre-injury work level and activities of daily living. CONCLUSION: Our results strongly suggest that ORIF with F-u-HA/PLLA screws and FiberLoop® could be an alternative treatment option for transverse patellar fractures.