Metamaterial Inspired Varactor-Tuned Antenna with Frequency Reconfigurability and Pattern Diversity.

A metamaterial-inspired varactor-tuned antenna with frequency reconfigurability and pattern diversity is designed. Two different versions of a reconfigurable structure are integrated into a single antenna to excite two different orthogonal patterns, which realizes pattern diversity for MIMO applications. The outer annular Composite Right-/Left-Handed Transmission Line (CRLH-TL) works at the 1 mode and provides a broadside pattern, and the inner circular radiator loaded with split ring resonators (SRR) operates at the 0 mode and radiates an omnidirectional pattern, which realizes pattern diversity. By using surface-mounted varactors, the operating frequencies for the two radiation patterns can be tuned over a wide frequency range, from 1.7 GHz to 2.2 GHz, covering the 1.71-2.17 GHz LTE band, and a low mutual coupling between the two radiators is achieved. The antenna has also been prototyped. The measured results are in good agreement with the simulation results, verifying the proposed concept. The dual-mode MIMO system equipped with the proposed antenna elements is discussed within the context of a 3-D channel model, and it shows a superior array compactness and spectral efficiency (SE) performance compared to scenarios with single-mode elements.

Personal exposure to radiofrequency electromagnetic fields: A comparative analysis of international, national, and regional guidelines.

A worldwide overview and analysis for the existing limits of human exposure to Radiofrequency Electromagnetic Fields (RF-EMF) is given in this paper. These reference levels have been established by different national and even regional governments, which can be based on the guidelines provided by the recommendations of the International Commission on Non-Ionizing Radiation Protection (ICNIRP), the International Committee on Electromagnetic Safety of the Institute of Electrical and Electronics Engineers (IEEE), and even in the United States of the Federal Communications Commission (FCC), as well as, are based on the so-called precautionary principle. Explicit reference is made to the exposure limits adopted in countries or regions, such as Canada, Italy, Poland, Switzerland, China, Russia, France, and regions of Belgium (Brussels, Flanders, Wallonia), where the limits are much lower than the international standards. The limits are compared to a selected set of in-situ measurements. This clearly shows that the measured values are typically very small compared to the international standards but could be somewhat higher compared to the reduced limits. Based on this observation and the reasonable assumption that the sensitivity of people to Electromagnetic Fields (EMF) is the same everywhere (whole-body), we propose the idea to establish a worldwide reference limit for the general public, thus applicable in all countries, if the ICNIRP considers it appropriate. Research must continue to generate measurement data that demonstrate the levels of exposure to which we are really exposed, and with this, provide arguments to the organizations that established the guidelines, especially the ICNIRP, to evaluate whether the current limits are too much. High and can be modified when considered pertinent. To the best of our knowledge, at no time has the reference level for the general public been exceeded.

Enhancing Circular Polarization Performance of Low-Profile Patch Antennas for Wearables Using Characteristic Mode Analysis.

A wearable antenna functioning in the 2.4 GHz band for health monitoring and sensing is proposed. It is a circularly polarized (CP) patch antenna made from textiles. Despite its low profile (3.34 mm thickness, 0.027 λ0), an enhanced 3-dB axial ratio (AR) bandwidth is achieved by introducing slit-loaded parasitic elements on top of analysis and observations within the framework of Characteristic Mode Analysis (CMA). In detail, the parasitic elements introduce higher-order modes at high frequencies that may contribute to the 3-dB AR bandwidth enhancement. More importantly, additional slit loading is investigated to preserve the higher-order modes while relaxing strong capacitive coupling invoked by the low-profile structure and the parasitic elements. As a result, unlike conventional multilayer designs, a simple single-substrate, low-profile, and low-cost structure is achieved. While compared to traditional low-profile antennas, a significantly widened CP bandwidth is realized. These merits are important for the future massive application. The realized CP bandwidth is 2.2-2.54 GHz (14.3%), which is 3-5 times that of traditional low-profile designs (thickness < 4 mm, 0.04 λ0). A prototype was fabricated and measured with good results.

Measurement studies of personal exposure to radiofrequency electromagnetic fields: A systematic review.

The last 25 years have seen an increase in the number of radiofrequency sources with the global adoption of smartphones as primary connectivity devices. The objective of this work was to review and evaluate the measured studies of personal exposure to Radiofrequency Electromagnetic Fields (RF-RMF) and meet the basic quality criteria eligible for inclusion in this Review, according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines, following the eligibility criteria of the PECO (Population, Exposure, Comparator, and Outcome) methodology, and the instrument for critical reading Critical Appraisal Skills Programme Español (CASPe). We systematically reviewed the works published between January 1, 1998, and December 31, 2021, yielding 56 publications. Of the different types of studies in which personal exposure to RF-EMF has been measured with two measurement methodologies can be highlighted: Personal measurements with volunteers and Personal measurements with a trained researcher (touring a specific area, one or several microenvironments, an entire city, walking or in some means of transport). Personal exposimeters were used in 83% of the studies. The lowest mean was measured in Egypt with a value of 0.00100 µW/m2 (1.00 nW/m2) in 2007 and the highest mean was measured in Belgium with a value of 285000 µW/m2 (0.285 W/m2) in 2019. The results of our study confirm that RF-EMF exposure levels are well below the maximum levels established by the ICNIRP guidelines.

Nonlocal response of plasmonic core-shell nanotopologies excited by dipole emitters.

In light of the emergence of nonclassical effects, a paradigm shift in the conventional macroscopic treatment is required to accurately describe the interaction between light and plasmonic structures with deep-nanometer features. Towards this end, several nonlocal response models, supplemented by additional boundary conditions, have been introduced, investigating the collective motion of the free electron gas in metals. The study of the dipole-excited core-shell nanoparticle has been performed, by employing the following models: the hard-wall hydrodynamic model; the quantum hydrodynamic model; and the generalized nonlocal optical response. The analysis is conducted by investigating the near and far field characteristics of the emitter-nanoparticle system, while considering the emitter outside and inside the studied topology. It is shown that the above models predict striking spectral features, strongly deviating from the results obtained via the classical approach, for both simple and noble constitutive metals.

Transmissive terahertz metasurfaces with vanadium dioxide split-rings and grids for switchable asymmetric polarization manipulation.

Metasurfaces containing arrays of thermally tunable metal-free (double-)split-ring meta-atoms and metal-free grids made of vanadium dioxide (VO[Formula: see text]), a phase-change material can deliver switching between (1) polarization manipulation in transmission mode as well as related asymmetric transmission and (2) other functionalities in the terahertz regime, especially when operation in the transmission mode is needed to be conserved for both phases of VO[Formula: see text]. As the meta-atom arrays function as arrays of metallic subwavelength resonators for the metallic phase of VO[Formula: see text], but as transmissive phase screens for the insulator phase of VO[Formula: see text], numerical simulations of double- and triple-array metasurfaces strongly indicate extreme scenarios of functionality switching also when the resulting structure comprises only VO[Formula: see text] meta-atoms and VO[Formula: see text] grids. More switching scenarios are achievable when only one meta-atom array or one grid is made of VO[Formula: see text] components. They are enabled by the efficient coupling of the geometrically identical resonator arrays/grids that are made of the materials that strongly differ in terms of conductivity, i.e. Cu and VO[Formula: see text] in the metallic phase.

Detecting mid-infrared light by molecular frequency upconversion in dual-wavelength nanoantennas.

Coherent interconversion of signals between optical and mechanical domains is enabled by optomechanical interactions. Extreme light-matter coupling produced by confining light to nanoscale mode volumes can then access single mid-infrared (MIR) photon sensitivity. Here, we used the infrared absorption and Raman activity of molecular vibrations in plasmonic nanocavities to demonstrate frequency upconversion. We converted approximately 10-micrometer-wavelength incoming light to visible light by surface-enhanced Raman scattering (SERS) in doubly resonant antennas that enhanced upconversion by more than 1010. We showed 140% amplification of the SERS anti-Stokes emission when an MIR pump was tuned to a molecular vibrational frequency, obtaining lowest detectable powers of 1 to 10 microwatts per square micrometer at room temperature. These results have potential for low-cost and large-scale infrared detectors and spectroscopic techniques.

A Wearable Button Antenna Sensor for Dual-Mode Wireless Information and Power Transfer.

A novel wearable button antenna sensor is proposed for the concept of simultaneous wireless information and power transfer (SWIPT). This integrates two working modes for the transfer of power and information, respectively, and optimizes transfer efficiency. An omni-directional radiation pattern is achieved in the 3.5 GHz World Interoperability for Microwave Access (WiMAX) band to support on-body wireless communications, while a circularly polarized broadside radiation pattern is obtained in the 5 GHz wireless local area networks (WLAN) band to harvest power. The measured -10 dB return loss bandwidths are 4.0% (3.47-3.61 GHz) in the lower band, and 25.0% (4.51-5.80 GHz) in the higher band, respectively. An artificial magnetic conductor (AMC) structure with wideband characteristics is applied to obtain a low-profile design and to increase the stability of the antenna sensor. A high radiation efficiency of over 80% in the whole working band is observed. The specific absorption rate (SAR) of the proposed antenna sensor is below 0.509 W/kg at 3.55 GHz, and below 0.0532 W/kg at 5.5 GHz, respectively, which is much lower than the European standard threshold of 2 W/kg. All these characteristics make the designed antenna sensor suitable for on-body information transmission and off-body energy harvesting. The antenna sensor has been prototyped. Simulations and measurements agree well, proving the validity of the new concept.

Medium-Sized Highly Coupled Planar Arrays with Maximum Aperture Efficiency.

This paper presents a technique to design strongly coupled planar arrays with very high aperture efficiency. The key innovation is that, based on an irregular 2 × 1 array, very compact medium-sized arrays of size 2 × 2, 2 × 4, and 2 × 6 are constructed with very strong and constructive mutual coupling between the elements. In this way, a maximum aperture efficiency is reached for a given footprint of the array. The occupied space of the antenna in comparison with conventional linear patch arrays is studied. A prototype 2 × 4 array operating around 5.8 GHz is designed, fabricated, built, and measured. The results show a large bandwidth of 20% and a very high aperture efficiency of 100%, which is the largest found in the literature for similarly sized arrays. These results are important in view of the future Internet of Things, where small and medium-sized arrays are planned to be mounted on numerous devices where a very limited physical area is available.

Bandwidth Optimization of a Textile PIFA with DGS Using Characteristic Mode Analysis.

This work presents the design and optimization of an antenna with defected ground structure (DGS) using characteristic mode analysis (CMA) to enhance bandwidth. This DGS is integrated with a rectangular patch with circular meandered rings (RPCMR) in a wearable format fully using textiles for wireless body area network (WBAN) application. For this integration process, both CMA and the method of moments (MoM) were applied using the same electromagnetic simulation software. This work characterizes and estimates the final shape and dimensions of the DGS using the CMA method, aimed at enhancing antenna bandwidth. The optimization of the dimensions and shape of the DGS is simplified, as the influence of the substrates and excitation is first excluded. This optimizes the required time and resources in the design process, in contrast to the conventional optimization approaches made using full wave "trial and error" simulations on a complete antenna structure. To validate the performance of the antenna on the body, the specific absorption rate is studied. Simulated and measured results indicate that the proposed antenna meets the requirements of wideband on-body operation.

Comparison of peak electromagnetic exposures from mobile phones operational in either data mode or voice mode.

The aim of this study is to compare the typical peak ElectroMagnetic (EM) exposures from smart phones during data transmission and voice calls, respectively, in the typical Western-European city of Leuven, Belgium. Since transmission powers towards the outdoor network in an indoor environment are expected to be higher than in an outdoor environment, measurements were executed indoors. The influence of factors like network generation [2G, 3G, and 4G] and choice of mobile operator was also investigated. The most important conclusion of the study is that there is a huge difference between peak exposures generated by the 3 network generations currently active in Leuven. To the average, in many cases the peak exposure for 3G is more than a factor 20 lower than for 2G, and about a factor 5-10 lower than for 4G. These numbers are much higher than expected. There are also systematic differences between peak exposures for data mode and voice mode.

A Novel Design Approach for Compact Wearable Antennas Based on Metasurfaces.

This paper presents a novel approach to design compact wearable antennas based on metasurfaces. The behavior of compact metasurfaces is modeled with a composite right-left handed transmission line (CRLH TL). By controlling the dispersion curve, the resonant modes of the compact metasurface can be tuned efficiently. A printed coplanar waveguide (CPW) monopole antenna is used as the feed structure to excite the compact metasurface, which will result in a low profile antenna with low backward radiation. Following this approach, two compact antennas are designed for wearable applications. The first antenna is designed to operate at its first negative mode (-1 mode), which can realize miniaturization, but maintain the broadside radiation as for a normal microstrip antenna. The proposed prototype resonates around 2.65 GHz, with a matching bandwidth of 300 MHz. The total dimensions of the antenna are 39.4 × 33.4 mm2 (0.1 λ02), and its maximum gain is 2.99 dBi. The second antenna targets dual-band operation at 2.45 and 3.65 GHz. A pair of symmetric modes (±1 modes) are used to generate similar radiation patterns in these two bands. The size of the antenna is 55.79 × 52.25 mm2 (0.2 λ02), and the maximum gains are 4.25 and 7.35 dBi in the two bands, respectively. Furthermore, the performance of the antennas is analyzed on the human body. The results show that the proposed antennas are promising candidates for Wireless Body Area Networks (WBAN).

Dual-Band Dual-Polarized Wearable Button Array With Miniaturized Radiator.

A dual-band dual-polarized wearable array is proposed, based on a miniaturized innovating button radiator topology. The diameter of the rigid button is only 19.5 mm (0.29 λ at 4.5 GHz), which optimizes the users' comfort, and makes it the smallest up to date in literature. The operational bands are 4.50-4.61 GHz and 5.04-5.50 GHz. The antenna thus covers the 4.5-4.6 unlicensed future 5th generation (5G) communication band for the internet of things (IoT), and the 5.1-5.5 GHz wireless local area network (WLAN) band, respectively. Two orthogonal linear polarizations are obtained in each band. A low mutual coupling between the button antenna elements (below -18 dB) and between the two ports within each element (below -20 dB) is achieved, guaranteeing a good diversity performance. The envelope correlation coefficient (ECC) and the specific absorption rate (SAR) performance are also analyzed. In order to demonstrate the robustness of the button antenna and to mimic realistic situations, a more complicated asymmetrical ground plane model of the button antenna is studied for the first time. A prototype of a two-element button array has been fabricated. The measurement results match well with the simulations. A 10-element button array is studied within the context of a 3-D channel model, taking into account the button element's radiation pattern. A high achievable spectral efficiency (SE) is obtained.

Study of the electromagnetic exposure from mobile phones in a city like environment: The case study of Leuven, Belgium.

A measuring campaign for the assessment of electromagnetic exposure levels from mobile phones in the city center of Leuven, Belgium, has been carried out. The main objective of the assessment is to study the dependency of the exposure of the user by his own mobile phone in terms of location in the city (very close to base stations and at randomly selected locations). The measurements were performed in both public and private areas in 60 outdoor and 60 indoor locations in Leuven. The campaign was focused on GSM 900 mobile communications. The results show that the exposure is considerably higher for indoor environments compared to outdoor environments, and at the randomly chosen locations compared to locations very close to base stations. However, the most important observation is that the average outdoor exposure in Leuven of the user of a mobile phone is about 8 times higher than the average outdoor exposure by base stations. Indoors, this factor rises to about 30.

Study of the correlation between outdoor and indoor electromagnetic exposure near cellular base stations in Leuven, Belgium.

A measuring campaign for the assessment of electromagnetic radiation near base stations in the city center of Leuven, Belgium, has been carried out. The main objective of this assessment is to study the correlation between the outdoor and the indoor exposure produced by cellular base stations and to investigate the changes of electromagnetic exposure within a typical day and over 1 month in the vicinity of these base stations. The study was also carried out as a function of location and time using highly precise measurement equipment. The measurements were performed in both public and private areas in sixty (30 indoor and 30 outdoor) different locations in Leuven. The measurement was focused on mobile communication networks: GSM (Global System for Mobile Communication, 900 MHz and 1800 MHz) and UMTS (Universal Mobile Telecommunications System, 2110 MHz) were the frequency bands of interest. The data at these frequencies were extracted from raw measurements in the 824-2170 MHz frequency band. The results show that all analyzed locations are in compliance with the exposure limits recommended by ICNIRP (International Commission on Non-Ionizing Radiation Protection) and that the (maximum) indoor exposure correlates to the outdoor exposure with a factor of about 0.5.

An Innovated Application of Reutilize Copper Smelter Slag for Cement-based Electromagnetic Interference Composites.

In the present study, it has been attempted an innovated application, i.e., electromagnetic interference shielding material, to reutilize copper smelter slag, aiming at an alternative high value added product. Notably, a proof-of-concept experiment with an addition of a 45 wt.% of copper slag alone to the cement matrix boost the shielding effectiveness (SE) to approximately 7-8 dB in the 500 MHz-1.5 GHz frequency range, highlights the incident electromagnetic wave has been weakened by approximately 60 pct. This phenomenon is attributed to the iron silicate, fayalite, and magnetite embedded in the sample mixture serve as magnetic and dielectric loss absorbent, deriving from the copper slag. Copper slag with low value application, shows its competitive economic and social advantages as candidate infill for electromagnetic interference shielding materials.

Temperature-mediated invocation of the vacuum state for switchable ultrawide-angle and broadband deflection.

Temperature-mediated appearance and disappearance of a deflection grating in a diffracting structure is possible by employing InSb as the grating material. InSb transits from the dielectric state to the plasmonic state in the terahertz regime as the temperature increases, this transition being reversible. An intermediate state is the vacuum state in which the real part of the relative permittivity of InSb equals unity while the imaginary part is much smaller. Then the grating virtually disappears, deflection being impossible as only specular reflection can occur. This ON/OFF switching of deflection and relevant angular filtering are realizable over wide ranges of frequency and incidence angle by a temperature change of as low as 20 K. The vacuum state of InSb invoked for ON/OFF switching of deflection and relevant angular filtering can also be obtained for thermally tunable materials other than InSb as well as by using non-thermal mechanisms.

Tailoring far-infrared surface plasmon polaritons of a single-layer graphene using plasmon-phonon hybridization in graphene-LiF heterostructures.

Being one-atom thick and tunable simultaneously, graphene plays the revolutionizing role in many areas. The focus of this paper is to investigate the modal characteristics of surface waves in structures with graphene in the far-infrared (far-IR) region. We discuss the effects exerted by substrate permittivity on propagation and localization characteristics of surface-plasmon-polaritons (SPPs) in single-layer graphene and theoretically investigate characteristics of the hybridized surface-phonon-plasmon-polaritons (SPPPs) in graphene/LiF/glass heterostructures. First, it is shown how high permittivity of substrate may improve characteristics of graphene SPPs. Next, the possibility of optimization for surface-phonon-polaritons (SPhPs) in waveguides based on LiF, a polar dielectric with a wide polaritonic gap (Reststrahlen band) and a wide range of permittivity variation, is demonstrated. Combining graphene and LiF in one heterostructure allows to keep the advantages of both, yielding tunable hybridized SPPPs which can be either forwardly or backwardly propagating. Owing to high permittivity of LiF below the gap, an almost 3.2-fold enhancement in the figure of merit (FoM), ratio of normalized propagation length to localization length of the modes, can be obtained for SPPPs at 5-9 THz, as compared with SPPs of graphene on conventional glass substrate. The enhancement is efficiently tunable by varying the chemical potential of graphene. SPPPs with characteristics which strongly differ inside and around the polaritonic gap are found.

Design of Wideband Button Antenna Based on Characteristic Mode Theory.

A wideband wearable button antenna working around 2.4 GHz is proposed in this paper. The function of the textile antenna ground is analyzed based on characteristic mode theory. By properly locating the button on the ground, the latter can be efficiently excited and operates as a radiator. This is shown to greatly increase the impedance bandwidth. The antenna is analyzed both in free space and on the human body. A prototype is fabricated, and the measured results agree satisfactorily with the simulations. In free space, the bandwidth, the realized gain, and radiation efficiency are 658 MHz, 1.8 dBi, and 97%, respectively. While on the human body, the values can reach 788 MHz, 5.1 dBi, and 71%, respectively. This wide band behavior provides robustness across different environments and to relatively large fabrication tolerances. The specific absorption rate is below 0.45 W/kg for an equivalent isotropically radiated power of 20 dBm.

Toward Electrically Tunable, Lithography-Free, Ultra-Thin Color Filters Covering the Whole Visible Spectrum.

The possibility of real-time tuning of optical devices has attracted a lot of interest over the last decade. At the same time, coming up with simple lithography-free structures has always been a challenge in the design of large-area compatible devices. In this work, we present the concept and the sample design of an electrically tunable, lithography-free, ultra-thin transmission-mode color filter, the spectrum of which continuously covers the whole visible region. A simple Metal-Insulator-Metal (MIM) cavity configuration is used. It is shown that using the electro-optic dielectric material of 4-dimethyl-amino-N-methyl-4-stilbazoliumtosylate (DAST) as the dielectric layer in this configuration enables efficient electrical tuning of the color filter. The total thickness of the structure is 120 nm, so it is ultra-thin. The output color gets tuned from violet to red by sweeping the applied voltage from -12 to +12 Volts (V). We present an in-detail optimization procedure along with a simple calculation method for the resonance wavelength of the MIM cavity that is based on circuit theory. Such power-efficient structures have a large variety of potential applications ranging from optical communication and switching to displays and color-tunable windows.