ABSTRACT
In this study, electrically insulating polyolefin elastomer (POE)-based phase change materials (PCMs) comprising alumina (Al2O3) and graphene nanoplatelets (GNPs) are prepared using a conventional injection moulding technique, which exhibits promising applications for solar energy storage due to the reduced interfacial thermal resistance, excellent stability, and proficient photo-thermal conversion efficiency. A synergistic interplay between Al2O3 and GNPs is observed, which facilitates the establishment of thermally conductive pathways within the POE/paraffin wax (POE/PW) matrix. The in-plane thermal conductivity of POE/PW/GNPs 5 wt%/Al2O3 40 wt% composite reaches as high as 1.82 W m-1K-1, marking a remarkable increase of ≈269.5% when compared with that of its unfilled POE/PW counterpart. The composite exhibits exceptional heat dissipation capabilities, which is critical for thermal management applications in electronics. Moreover, POE/PW/GNPs/Al2O3 composites demonstrate outstanding electrical insulation, enhanced mechanical performance, and efficient solar energy conversion and transportation. Under 80 mW cm-2 NIR light irradiation, the temperature of the POE/PW/GNPs 5 wt%/Al2O3 40 wt% composite reaches approximately 65 °C, a notable 20 °C improvement when compared with the POE/PW blend. The pragmatic and uncomplicated preparation method, coupled with the stellar performance of the composites, opens a promising avenue and broader possibility for developing flexible PCMs for solar conversion and thermal storage applications.
ABSTRACT
The demand for flexible strain sensors with high sensitivity and durability has increased significantly. However, traditional sensors are limited in terms of their detection ranges and fabrications. In this work, a space stacking method was proposed to fabricate natural rubber (NR)/ Ti3C2Tx (MXene)/silica (SiO2) films that possessed exceptional electrical conductivity, sensitivity and reliability. The introduction of SiO2 into the NR/MXene composite enabled the construction of an "island-chain structure", which promoted the formation of conductive pathways and significantly improved the conductivity of the composite. Specifically, the electrical conductivity of the NR/MXene/10 wt%SiO2 composite was enhanced by about 200 times compared to that of the NR/MXene composite alone (from 0.07 to 13.4 S/m). Additionally, the "island-chain structure" further enhanced the sensing properties of the NR/MXene/10 wt%SiO2 composite, as evidenced by its excellent sensitivity (GF = 189.2), rapid response time (102 ms), and good repeatability over 10,000 cycles. The fabricated device demonstrates an outstanding mechanical sensing performance and can accurately detect human physiological signals. Specifically, the device serves as a strain detector, recognizing different strain signals by monitoring the movement of fingers, arms, and thighs. This study provides critical insights into composite manufacturing with exceptional conductivity, flexibility and stability, which are essential properties for creating high-performance flexible sensors.
Subject(s)
Rubber , Silicon Dioxide , Humans , Reproducibility of Results , Electric ConductivityABSTRACT
Due to the properties of a positive temperature coefficient (PTC) effect and a negative temperature coefficient (NTC) effect, electrically conductive polymer composites (CPCs) have been widely used in polymer thermistors. A dual percolated conductive microstructure was prepared by introducing the polybutylene adipate terephthalate phase (PBAT) into graphene nanoplatelets (GNPs)-filled polylactic acid (PLA) composites, intending to develop a favorable and stable PTC material. To achieve this strategy, GNPs were selectively distributed in the PBAT phase by injection molding. In this study, we investigated the crystallization behavior, electrical conductivity, and temperature response of GNP-filled PLA/PBAT composites. The introduction of GNPs into PLA significantly increased PLA crystallization capacity, where the crystallization onset temperature (To) is raised from 116.7 °C to 134.7 °C, and the crystallization half-time (t1/2) decreases from 35.8 min to 27.3 min. The addition of 5 wt% PBAT increases the electrical conductivity of PLA/PBAT/GNPs composites by almost two orders of magnitude when compared to PLA/GNPs counterparts. The temperature of the heat treatment is also found to play a role in affecting the electrical conductivity of PLA-based composites. Increasing crystallinity is favorable for increasing electrical conductivity. PLA/PBAT/GNPs composites also show a significant positive temperature coefficient, which is reflected in the temperature-electrical resistance cycling tests.