BF4- Tailoring Solvation Chemistry of Ether-Based Electrolytes to Construct Stable Electrode/Electrolyte Interfaces for Sodium-Ion Full Batteries.

The ether-based electrolytes show excellent performance on anodes in sodium-ion batteries (SIBs), but they still show poor compatibility with the cathodes. Here, ether electrolytes with NaBF4 as the main salt or additive were applied in NFM//HC full cells and showed enhanced performance than the electrolyte with NaPF6. Then, BF4- was found to have a stronger interaction with Na+, which could reduce the solvation of Na+ with the solvent, thus inducing the formation of the cathode electrolyte interface (CEI) and solid electrolyte interface (SEI) layers rich in inorganic species. Moreover, the morphology, structure, composition, and solubility of CEI and SEI were explored, concluding that NaBF4 could induce more stable CEI and SEI layers rich in B-containing species and inorganics. This work proposes using NaBF4 as the main salt or additive to improve the performance of ether electrolytes in NFM//HC full cells, which provides a strategy to improve the compatibility of ether-based electrolytes and cathodes.

Spray Pyrolysis Regulated FeCo Alloy Anchoring on Nitrogen-Doped Carbon Hollow Spheres Boost the Performance of Zinc-Air Batteries.

Low-cost and high-efficiency non-precious metal-based oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) bifunctional catalysts are the key to promoting the commercial application of metal-air batteries. Herein, a highly efficient catalyst of Fe0.18 Co0.82 alloy anchoring on the nitrogen-doped porous carbon hollow sphere (Fex Co1-x /N-C) is intelligently designed by spray pyrolysis (SP). The zinc in the SP-derived metal oxides and metal-organic framework volatilize at high temperature to construct a hierarchical porous structure with abundant defects and fully exposes the FeCo nanoparticles which uniformly anchor on the carbon substrate. In this structure, the coexistence of Fe0.18 Co0.82 alloy and binary metal active sites (Fe-Nx /Co-Nx ) guarantees the Fe0.2 Co0.8 /N-C catalyst exhibiting an excellent half-wave potential (E1/2 ═ 0.84 V) superior to 20% Pt/C for ORR and a suppressed overpotential (280 mV) than RuO2 for OER. Assembled rechargeable Zn-air battery (RZAB) demonstrates a promising specific capacity of 807.02 mAh g-1 , peak power density of 159.08 mW cm-2 and durability without electrolyte circulation (550 h). This work proposes the design concept of utilizing an oxide core to in situ consume the porous carbon shell for anchoring metal active sites and construct defects, which benefits from spray pyrolysis in achieving precise control of the alloy structure and mass preparation.

Breaking the Solubility Limit of LiNO3 in Carbonate Electrolyte Assisted by BF3 to Construct a Stable SEI Film for Dendrite-Free Lithium Metal Batteries.

Lithium (Li) metal is regarded as a potential candidate for the next generation of lithium secondary batteries, but it has poor cycling stability with the broadly used carbonate-based electrolytes due to the uncontrollable dendritic growth and low Coulombic efficiency (CE). LiNO3 is an effective additive and its limited solubility (<800 ppm) in carbonate-based electrolytes is still a challenge, as reported. Herein, using BF3 (Lewis acid) is proposed to enhance the solubility of LiNO3 in carbonate-based electrolytes. The dissolved NO3 - can be involved in the first solvation shell of Li+, reducing the coordination number of PF6 - and EC (ethylene carbonate). In addition, the NO3 - is proved to be preferentially reduced on Li metal by differential electrochemical mass spectrometry so that the decomposition of PF6 - and EC is suppressed. Therefore, a SEI layer containing Li3N can be obtained, which exhibits high lithium-ion conductivity, achieving even and dense Li deposits. Consequently, the CE of Li||Cu cell with BF3/LiNO3 can be increased to 98.07%. Moreover, the capacity retention of Li||LiFePO4 with a low N/P ratio (3:1) is as high as 90% after 300 cycles (≈1500 h). This work paved a new way for incorporating LiNO3 into carbonate-based electrolytes and high-performance lithium metal batteries.

Sex-Specific Cardiac Troponin Thresholds in Transgender Patients With Suspected Acute Coronary Syndrome.

This cohort study compares the use and outcomes of high-sensitivity cardiac troponin assay vs conventional troponin assay in transgender adults.

Uncovering the Redox Shuttle Degradation Mechanism of Ether Electrolytes in Sodium-Ion Batteries and its Inhibition Strategy.

Ether-based electrolytes exhibit excellent performance when applied in different anode materials of sodium ion batteries (SIBs), but their exploration on cathode material is deficient and the degradation mechanism is still undiscovered. Herein, various battery systems with different operation voltage ranges are designed to explore the electrochemical performance of ether electrolyte. It is found for the first time that the deterioration mechanism of ether electrolyte is closely related to the "redox shuttle" between cathode and low-potential anode. The "shuttle" is discovered to occur when the potential of anodes is below 0.57 V, and the gas products coming from "shuttle" intermediates are revealed by differential electrochemical mass spectrometry (DEMS). Moreover, effective inhibition strategies by protecting low-potential anodes are proposed and verified; ethylene carbonate (EC) is found to be very effective as an additive by forming an inorganics-rich solid electrolyte interphase (SEI) on low-potential anodes, thereby suppressing the deterioration of ether electrolytes. This work reveals the failure mechanism of ether-based electrolytes applied in SIBs and proposes effective strategies to suppress the "shuttle," which provides a valuable guidance for advancing the application of ether-based electrolytes in SIBs.

Uniform Densification of Garnet Electrolyte for Solid-State Lithium Batteries.

Highly uniformly dense garnet type solid-state electrolyte plays a significant role in determining the performance of solid-state lithium batteries. Herein, a rational powder-covering sintering strategy is proposed and demonstrated, in which narrow-particle-size-distribution fine powder and uniform sintering temperature distribution are considered as very significant factors. It is suggested that powder materials with wider particle size distribution dramatically decrease the densified level of electrolytes. Slow temperature elevating rate and the overhead structure of bearing table are found to be beneficial to uniform densification. Moreover, the uniform densification process of sintering solid-state electrolyte is studied both microscopically and macroscopically, which can be divided into three phases according to the grain growing evolution and linear shrinkage patterns. The ionic conductivity of the as-prepared Li6.4 La3 Zr1.4 Ta0.6 O12 (LLZTO) garnet electrolyte is determined to be 0.73 mS cm-1 at 303 K with an activation energy of 0.37 eV. The Li/LLZTO/Li symmetric cell exhibits a small interfacial impedance of 8.49 Ω cm2 and a high apparent critical current density of 2.15 mA cm-2 and also can be cycled for 1000 h continuously without short-circuit. Such results indicate the good feasibility of as-proposed sintering strategy to prepare uniformly dense garnet type solid-state electrolytes for solid-state lithium batteries.

A Fresh One-Step Spray Pyrolysis Approach to Prepare Nickel-Rich Cathode Material for Lithium-Ion Batteries.

The Ni-rich layered cathode material LiNi0.8Co0.1Mn0.1O2 (NCM811) with high specific capacity and acceptable rate performance is one of the key cathode materials for high-energy-density lithium-ion batteries. Coprecipitation, the widely utilized method in the precursor synthesis of NCM811 materials, however, suffers long synthetic processes and challenges in uniform element distribution. The spray pyrolysis method is able to prepare oxide precursors in seconds where all transition-metal elements are well distributed, but the difficulty of lithium distribution will also arise when the lithium salts are added in the subsequent sintering process. Herein, a fresh one-step spray pyrolysis approach is proposed for preparing high-performance NCM811 cathode materials by synthesizing lithium-contained precursors in which all elements are well distributed at a molecular level. The precursors with folded morphology and exceptional uniformity are successfully obtained at a low pyrolysis temperature of 300 °C by an acetate system. Furthermore, the final products commendably inherit the folded morphology of the precursors and exhibit excellent cyclic retentions of 94.6% and 88.8% after 100 and 200 cycles at 1 C (1 C = 200 mA g-1), respectively.

Inhibiting Mn Migration by Sb-Pinning Transition Metal Layers in Lithium-Rich Cathode Material for Stable High-Capacity Properties.

Owing to the interacted anion and cation redox dynamics in Li2 MnO3 , the high energy density can be obtained for lithium-rich manganese-based layered transition metal (TM) oxide [Li1.2 Ni0.2 Mn0.6 O2 , LNMO]. However, irreversible migration of Mn ions and oxygen release during highly de-lithiation can destroy its layered structure, leading to voltage and capacity decline. Herein, non-TM antimony (Sb) is pinned to the TM layer of LNMO by a facile sol-gel method. High-resolution ex and in situ characterization technologies manifest that the introduction of trace Sb inhibits the migration of Mn ions, forming a more stable structure. Sb can impressively adjust the Mn-O interaction between anions and cations, beneficial to decrease the energy level of Mn 3d and O 2p orbitals and expand their band gap according to the  theoretical calculation results. As a result, the discharge specific capacity and the energy density for SbLi1.2 [Ni0.2 Mn0.6 ]O2 (SLNMO) reaches as high as 301 mAh g-1 and 1019.6 Wh kg-1 at 0.1 C, respectively. Moreover, the voltage decay is reduced by 419.8 mV compared with LNMO. The regulative interaction between Mn 3d and isolated O 2p bands provides an accurate guidance for solving electrochemical performance deficiencies of lithium-rich manganese-based cathode oxide.

Research Progress of Single-Crystal Nickel-Rich Cathode Materials for Lithium Ion Batteries.

Single-crystal nickel-rich cathode materials (SC-NRCMs) are the most promising candidates for next-generation power batteries which enable longer driving range and reliable safety. In this review, the outstanding advantages of SC-NRCMs are discussed systematically in aspects of structural and thermal stabilities. Particularly, the intergranular-crack-free morphology exhibits superior cycling performance and negligible parasitic reactions even under severe conditions. Besides, various synthetic methods are summarized and the relation between precursor, sintering process, and final single-crystal products are revealed, providing a full view of synthetic methods. Then, challenges of SC-NRCMs in fields of kinetics of lithium diffusion and the one particularly occurred at high voltage (intragranular cracks and aggravated parasitic reactions) are discussed. The corresponding mechanism and modifications are also referred. Through this review, it is aimed to highlight the magical morphology of SC-NRCMs for application perspective and provide a reference for following researchers.

Change in Invasively Measured Mean Pulmonary Artery Pressure After Transcatheter Mitral Valve Repair Is Associated With Heart Failure Readmission.

BACKGROUND: Pre-existing pulmonary hypertension is associated with poor outcomes after transcatheter mitral valve repair (TMVr) for mitral regurgitation (MR). However, the impact of an immediate change in mean pulmonary artery pressure (ΔmPAP) following TMVr on outcomes is unknown. METHODS: Patients who underwent TMVr from December 2015 to February 18, 2020 at our institution for symptomatic 3-4+ MR and who had invasive hemodynamics measured immediately pre- and post-TMVR were included. Multivariate Cox regression analysis was performed to examine the association of ΔmPAP (post-TMVr - pre-TMVr mPAP) with the primary endpoint of heart failure (HF) readmission at 1 year. Secondary endpoints included all-cause mortality and the composite endpoint of HF readmission or all-cause mortality at 1 year. RESULTS: Among 55 patients, 55% were men, mean age was 72 ± 14.2 years, and mean ΔmPAP was -1.4 ± 8.2 mm Hg. Overall, HF readmission occurred in 14 (25%), death in 10 (18%), and the composite endpoint in 20 (36%) patients. In multivariable analyses, higher ΔmPAP was significantly associated with HF readmission (hazard ratio (HR) = 1.10, 95% confidence interval (CI): 1.00 - 1.21; P = 0.04). ΔmPAP was not associated with death (HR = 1.04, 95% CI: 0.96 - 1.14; P = 0.33), though there was a numerical but statistically non-significant trend towards the composite endpoint (HR = 1.06, 95% CI: 1.00 - 1.13; P = 0.06) driven by HF readmission. CONCLUSION: Higher ΔmPAP immediately following TMVr was associated with increased HF readmission at 1 year. Larger prospective studies are needed to validate these data and further explore the utility of ΔmPAP as a novel hemodynamic parameter to predict post-TMVR outcomes.

Highly-Dispersed Submicrometer Single-Crystal Nickel-Rich Layered Cathode: Spray Synthesis and Accelerated Lithium-Ion Transport.

For conventional polycrystalline Ni-rich cathode material consisting of numerous primary particles in disordered orientation, the crystal anisotropy in charge/discharge process results in the poor rate capability and rapid capacity degradation. In this work, highly-dispersed submicron single-crystal LiNi0.8 Co0.15 Al0.05 O2 (SC-NCA) cathode is efficiently prepared by spray pyrolysis (SP) technique followed by a simple solid-state lithiation reaction. Porous Ni0.8 Co0.15 Al0.05 Ox precursor prepared via SP exhibits high chemical activity for lithiation reaction, enabling the fabrication of single-crystal cathode at a relatively low temperature. In this way, the contradiction between high crystallinity and cation disordering is well balanced. The resulted optimized SC-NCA shows polyhedral single-crystal morphology with moderate grain size (≈1 µm), which are beneficial to shortening the Li+ diffusion path and improving the structural stability. As cathode for lithium ion batteries, SC-NCA delivers a high discharge capacity of 202 and 140 mAh g-1 at 0.1 and 10 C, respectively, and maintains superior capacity retention of 161 mAh g-1 after 200 cycles at 1C. No micro-crack is observed in the cycled SC-NCA particles, indicating such single-crystal morphology can greatly relieve the anisotropic micro-strain. This effective, continuous and adaptable strategy for preparing single-crystal Ni-rich cathode without any additive may accelerate their practical application.

A Renewable Sedimentary Slurry Battery: Preliminary Study in Zinc Electrodes.

Low-cost, scalable energy storage is the key to continuing growth of renewable energy technologies. Here a battery with sedimentary slurry electrode (SSE) is proposed. Through the conversion of discrete particles between sedimentary and suspending types, it not only inherits the advantages of semi-solid flow cell but also exhibits high energy density and stable conductive network. Given an example, the zinc SSE (ZSSE) delivers a large discharge capacity of 479.2 mAh g-1 at 10 mA cm-2. More importantly, by renewal of the slurry per 20 cycles, it can run for 112 and 75 cycles before falling below 80% of designed capacity under 10 mA cm-2 (20% DODZn) and 25 mA cm-2 (25% DODZn), respectively. The lost capacity after cycles is able to recover after slurry renewal and the end-of-life SSE can be easily reused by re-formation. The concept of SSE brands a new way for electrochemical energy storage.

Effect of phase-change material blood containers on the quality of red blood cells during transportation in environmentally-challenging conditions.

BACKGROUND: The effect of phase-change material blood containers on the quality of stored red blood cells (RBCs) transported in the Qinghai-Tibet Plateau remains to be studied. STUDY DESIGN AND METHODS: RBCs stored in a phase-change material blood container were transported from Chengdu to Tibet and then back to Chengdu. The detection time points were the 1st day of fresh-collected RBCs (group 1), the 14th day of resting refrigerated storage (group 2), and the 14th day of plateau transportation under refrigerated storage in the container (group 3). RBC counts, hemoglobin (HGB) content, free hemoglobin (FHb) content, blood biochemical indexes, hemorheologic indexes and 2,3-DPG content were detected. RESULTS: Compared with group 2, RBC counts and HGB were decreased, and the mean corpuscular volume (MCV), FHb and K+ content were increased in group 3. The glucose consumption and lactic acid production were significantly increased in groups 2 and 3. Compared with group 2, the 2,3-DPG content and whole blood viscosity were decreased in group 3. After resting refrigerated storage and plateau transportation, the RBC quality still met the national standard (GB18469-2012 whole blood and component blood quality requirements). CONCLUSION: The phase-change material blood container can be maintained at a constant temperature under plateau environmental conditions, ensuring that the quality of the stored RBCs is compliant with GB18469-2012 whole blood and component blood quality requirements.

Novel LiV(PO4)0.9F1.3 with ultrahigh rate capability and prolonged cycle life.

Novel triclinic LiV(PO4)0.9F1.3, characterized through its crystal lattice expansion, ultrafine primary particle size and uniform carbon coating, was designed and fabricated through regulating the PO4/F ratio. It exhibited excellent electrochemical performance, maintaining 105 mA h g-1 at 50C and 92.9% capacity retention after 500 cycles at 10C due to its superior structural stability, greater charge transfer properties, enhanced electronic conductivity and fast Li+ diffusion kinetics.

Advances in nanostructures fabricated via spray pyrolysis and their applications in energy storage and conversion.

Functional nanostructured materials have attracted great attention over the past several decades owing to their unique physical and chemical properties, while their applications have been proven to be advantageous not only in fundamental scientific areas, but also in many technological fields. Spray pyrolysis (SP), which is particularly facile, effective, highly scalable and suitable for on-line continuous production, offers significant potential for the rational design and synthesis of various functional nanostructured materials with tailorable composition and morphology. In this review, we summarize the recent progress in various functional nanostructured materials synthesized by SP and their potential applications in energy storage and conversion. After a brief introduction to the equipment, components, and working principles of the SP technique, we thoroughly describe the guidelines and strategies for designing particles with controlled morphology, composition, and interior architecture, including hollow structures, dense spheres, yolk-shell structures, core-shell structures, nanoplates, nanorods, nanowires, thin films, and various nanocomposites. Thereafter, we demonstrate their suitability for a wide range of energy storage and conversion applications, including electrode materials for rechargeable batteries, supercapacitors, highly active catalysts for hydrogen production, carbon dioxide reduction and fuel cells, and photoelectric materials for solar cells. Finally, the potential advantages and challenges of SP for the preparation of nanostructured materials are particularly emphasized and discussed, and several perspectives on future research and development directions of SP are highlighted. We expect that this continuous, one-pot, and controllable synthetic technology can serve as a reference for preparing various advanced functional materials for broader applications.

Fluidized bed reaction towards crystalline embedded amorphous Si anode with much enhanced cycling stability.

A facile and large-scale fluidized bed reaction route was introduced for the first time to prepare crystalline embedded amorphous silicon nanoparticles with an average size of 50 nm as anode materials for lithium-ion batteries. By increasing the operating potential to control the electrochemically active degree, the resulting sample showed excellent cycle stability with a high capacity retention of 94.7% after 200 cycles at 1 A g-1 in the voltage range of 0.12-2.00 V.

Nondestructive Measurement of Hemoglobin in Blood Bags Based on Multi-Pathlength VIS-NIR Spectroscopy.

Hemoglobin concentration is an indicator for assessing blood product quality. To measure hemoglobin concentration in blood products without damaging blood bags, we proposed a method based on visible-near infrared transmission spectroscopy. Complex optical properties of blood bag walls result in measurement irregularities. Analyses showed that the slope of the light intensity-pathlength curve was more robust to the influence of the blood bag wall. In this study, the transmission spectra of red blood cell suspensions at multiple optical pathlengths were obtained, and the slopes of logarithmic light intensity-pathlength curves were calculated through curve fitting. A nondestructive measurement of hemoglobin content was achieved by using a regression model correlating slope spectra and hemoglobin concentration. Sixty samples with hemoglobin concentrations ranging from 72 to 161 g/L were prepared. Among them, 40 samples were used as a calibration set, and the remaining 20 samples were used as a prediction set. The determination coefficient of the prediction set was 0.97, with a mean square error of 2.78 g/L. This result demonstrates that a non-destructive measurement of hemoglobin levels in blood bags can be achieved by multiple-pathlength transmission spectroscopy.

Lightweight Reduced Graphene Oxide@MoS2 Interlayer as Polysulfide Barrier for High-Performance Lithium-Sulfur Batteries.

The further development of lithium-sulfur (Li-S) batteries is limited by the fact that the soluble polysulfide leads to the shuttle effect, thereby reducing the cycle stability and cycle life of the batteries. To address this issue, here a thin and lightweight (8 µm and 0.24 mg cm-2) reduced graphene oxide@MoS2 (rGO@MoS2) interlayer between the cathode and the commercial separator is developed as a polysulfide barrier. The rGO plays the roles of both a polysulfide physical barrier and an additional current collector, while MoS2 has a high chemical adsorption for polysulfides. The experiments demonstrate that the Li-S cell constructed with an rGO@MoS2-coated separator shows a high reversible capacity of 1122 mAh g-1 at 0.2 C, a low capacity fading rate of 0.116% for 500 cycles at 1 C, and an outstanding rate performance (615 mAh g-1 at 2 C). Such an interlayer is expected to be ideal for lithium-sulfur battery applications because of its excellent electrochemical performance and simple synthesis process.

BODIPY-Based Conjugated Porous Polymer and Its Derived Porous Carbon for Lithium-Ion Storage.

Conjugated porous polymers (CPPs) possess great potential in the energy storage aspect. In this work, a boron-dipyrromethene (BODIPY)-conjugated porous polymer (CPP-1) is achieved by a traditional organic synthesis route. Following this, a carbonization process is employed to obtain the carbonized porous material (CPP-1-C). The two as-prepared samples, which are characterized by doping with heteroatoms and their porous structure, are able to shorten the lithium-ion pathways and improve the lithium-ion storage property. Then, CPP-1 and CPP-1-C are applied as anode materials in lithium-ion batteries. As expected, long-term cyclic performances at 0.1 and 1 A g-1 are achieved with maintaining the specific capacity at 273.2 mA h g-1 after 100 cycles at 0.1 A g-1 and 250.8 mA h g-1 after 300 cycles at 1 A g-1. The carbonized sample exhibits a better electrochemical performance with a reversible specific capacity of 675 mA h g-1 at 0.2 A g-1. Moreover, the capacity is still stabilized at 437 mA h g-1 after 500 cycles at 0.5 A g-1. These results demonstrate that BODIPY-based CPPs are capable of being exploited as promising candidates for electrode materials in the fields of energy storage and conversion.

Note: Demodulation of spectral signal modulated by optical chopper with unstable modulation frequency.

When an optical chopper is used to modulate the light source, the rotating speed of the wheel may vary with time and subsequently cause jitter of the modulation frequency. The amplitude calculated from the modulated signal would be distorted when the frequency fluctuations occur. To precisely calculate the amplitude of the modulated light flux, we proposed a method to estimate the range of the frequency fluctuation in the measurement of the spectrum and then extract the amplitude based on the sum of power of the signal in the selected frequency range. Experiments were designed to test the feasibility of the proposed method and the results showed lower root means square error than the conventional way.