ABSTRACT
Knowledge of the minimal detectable bone fracture gap is essential in three-dimensional (3D) models, particularly in pre-operative planning of osteosynthesis to avoid overlooking gaps. In this study, defined incisions and bony displacements ranging from 100 to 400 µm were created in diaphyseal radii in 20 paired forearm specimens and verified with light microscopy. The specimens were scanned utilizing different computed tomography (CT) technologies/scanners, specimen positionings, scan protocols, image segmentations, and processing protocols. Inter- and intra-operator variabilities were reported as coefficient kappa. In CT images, fracture gaps of 100 µm and bone lamellae of 300 µm and 400 µm width were identified at a rate of 80 to 100%, respectively, independent of the investigated settings. In contrast, only 400µm incisions and bony displacements were visible in digital 3D models, with detection rates dependent on CT technology, image segmentation, and post-processing algorithm. 3D bone models based on state-of-the-art CT imaging can reliably visualize clinically relevant bone fracture gap sizes. However, verification of fractures to be surgically addressed should be verified with the original CT image series.
ABSTRACT
Aims: Serum inflammatory parameters are widely used to aid in diagnosing a periprosthetic joint infection (PJI). Due to their limited performances in the literature, novel and more accurate biomarkers are needed. Serum albumin-to-globulin ratio (AGR) and serum CRP-to-albumin ratio (CAR) have previously been proposed as potential new parameters, but results were mixed. The aim of this study was to assess the diagnostic accuracy of AGR and CAR in diagnosing PJI and to compare them to the established and widely used marker CRP. Methods: From 2015 to 2022, a consecutive series of 275 cases of revision total hip (n = 129) and knee arthroplasty (n = 146) were included in this retrospective cohort study. Based on the 2021 European Bone and Joint Infection Society (EBJIS) definition, 144 arthroplasties were classified as septic. Using receiver operating characteristic curve (ROC) analysis, the ideal thresholds and diagnostic performances were calculated. The areas under the curve (AUCs) were compared using the z-test. Results: AGR, CAR, and CRP were associated with PJI (p < 0.001). Sensitivities were 62.5% (95% CI 54.3 to 70.0), 73.6% (95% CI 65.8 to 80.1), and 71.5% (95% CI 63.6 to 78.3), respectively. Specificities were calculated with 84.7% (95% CI 77.5 to 89.9), 86.3% (95% CI 79.2 to 91.2), and 87.8% (95% CI 80.9 to 92.4), respectively. The AUC of CRP (0.797 (95% CI 0.750 to 0.843)) was significantly higher than the AUC of AGR (0.736 (95% CI 0.686 to 0.786), p < 0.001), and similar to AUC of CAR (0.799 (95% CI 0.753 to 0.846), p = 0.832). Decreased sensitivities were observed in PJIs caused by low-virulence organisms (AGR: 60%, CAR: 78%) compared to high-virulence pathogens (AGR: 80%, p = 0.042; CAR: 88%, p = 0.158). Higher sensitivities were seen in acute haematogenous (AGR: 83%, CAR: 96%) compared to chronic PJIs (AGR: 54%, p = 0.001; CAR: 65%, p < 0.001). Conclusion: Serum AGR and CAR showed limited diagnostic accuracy (especially in low-grade and chronic infections) and did not outperform the established marker CRP in our study. Hence, neither parameter can be recommended as an additional tool for diagnosing PJI.
ABSTRACT
OBJECTIVES: The revised European Society of Musculoskeletal Radiology (ESSR) consensus guidelines on soft tissue tumor imaging represent an update of 2015 after technical advancements, further insights into specific entities, and revised World Health Organization (2020) and AJCC (2017) classifications. This second of three papers covers algorithms once histology is confirmed: (1) standardized whole-body staging, (2) special algorithms for non-malignant entities, and (3) multiplicity, genetic tumor syndromes, and pitfalls. MATERIALS AND METHODS: A validated Delphi method based on peer-reviewed literature was used to derive consensus among a panel of 46 specialized musculoskeletal radiologists from 12 European countries. Statements that had undergone interdisciplinary revision were scored online by the level of agreement (0 to 10) during two iterative rounds, that could result in 'group consensus', 'group agreement', or 'lack of agreement'. RESULTS: The three sections contain 24 statements with comments. Group consensus was reached in 95.8% and group agreement in 4.2%. For whole-body staging, pulmonary MDCT should be performed in all high-grade sarcomas. Whole-body MRI is preferred for staging bone metastasis, with [18F]FDG-PET/CT as an alternative modality in PET-avid tumors. Patients with alveolar soft part sarcoma, clear cell sarcoma, and angiosarcoma should be screened for brain metastases. Special algorithms are recommended for entities such as rhabdomyosarcoma, extraskeletal Ewing sarcoma, myxoid liposarcoma, and neurofibromatosis type 1 associated malignant peripheral nerve sheath tumors. Satisfaction of search should be avoided in potential multiplicity. CONCLUSION: Standardized whole-body staging includes pulmonary MDCT in all high-grade sarcomas; entity-dependent modifications and specific algorithms are recommended for sarcomas and non-malignant soft tissue tumors. CLINICAL RELEVANCE STATEMENT: These updated ESSR soft tissue tumor imaging guidelines aim to provide support in decision-making, helping to avoid common pitfalls, by providing general and entity-specific algorithms, techniques, and reporting recommendations for whole-body staging in sarcoma and non-malignant soft tissue tumors. KEY POINTS: An early, accurate, diagnosis is crucial for the prognosis of patients with soft tissue tumors. These updated guidelines provide best practice expert consensus for standardized imaging algorithms, techniques, and reporting. Standardization can improve the comparability examinations and provide databases for large data analysis.
ABSTRACT
PURPOSE: In forensic medicine, maceration is often essential for examining bone surfaces, serving purposes such as identifying cut marks, making geometric measurements, and determining the victim's age. While hot water maceration removes soft tissue effectively, it is known to cause bone surface shrinkage. This raises the question of whether this effect is permanent or if it can be partially reversed through rehydration, considering the presence of soft tissue. METHODS: Computed tomography (CT) scans were conducted on the radii of 20 paired human anatomic forearm specimens. Subsequently, the radii were extracted, macerated in 60 °C water, CT-scanned in an air environment, rehydrated, re-implanted into the forearms, and CT-scanned again. RESULTS: Maceration resulted in a mean shrinkage of 0.12 mm on the outer bone surface. This shrinkage was nearly fully recoverable for the diaphysis after rehydration and accounting for soft tissue surrounding the bone. In contrast, the epiphysis showed permanent shrinkage, likely due to the loss of small bone fragments. Analysis of the inner bone surface indicated a smaller effect, but with significant standard deviations, especially for the epiphysis, possibly related to the less well-defined nature of the inner bone surface. CONCLUSION: The epiphyseal surface of hot water-macerated bone will, on average, be approximately 0.15 mm deflated and cannot retain the original surface. On the other hand, the diaphyseal surface is less affected and can be nearly completely restored after rehydration and accounting for soft tissue surrounding the bone.
ABSTRACT
PURPOSE: Osteosarcoma may arise as a secondary cancer following leukemias or lymphomas. We intended to increase the knowledge about such rare events. PATIENTS AND METHODS: We searched the Cooperative Osteosarcoma Study Group's database for individuals who developed their osteosarcoma following a previous hematological malignancy. The presentation and treatment of both malignancies was investigated, and additional neoplasms were noted. Outcomes after osteosarcoma were analyzed and potential prognostic factors were searched for. RESULTS: A total of 33 eligible patients were identified (male: 23, female: 10; median age: 12.9 years at diagnosis of hematological cancer; 20 lymphomas, 13 leukemias). A cancer predisposition syndrome was evident in one patient only. The hematological cancers had been treated by radiotherapy in 28 (1 unknown) and chemotherapy in 26 cases, including bone-marrow transplantation in 9. The secondary bone sarcomas (high-grade central 27, periosteal 2, extra-osseous 2, undifferentiated pleomorphic sarcoma of bone 2) arose after a median lag-time of 9.4 years, when patients were a median of 19.1 years old. Tumors were considered radiation-related in 26 cases (1 unknown). Osteosarcoma-sites were in the extremities (19), trunk (12), or head and neck (2). Metastases at diagnosis affected eight patients. Information on osteosarcoma therapy was available for 31 cases. All of these received chemotherapy. Local therapy involved surgery in 27 patients, with a good response reported for 9/18 eligible patients. Local radiotherapy was given to three patients. The median follow-up was 3.9 (0.3-12.0) years after bone tumor diagnosis. During this period, 21 patients had developed events as defined, and 15 had died, resulting in 5-year event-free and overall survival rates of 40% (standard error: 9%) and 56% (10%), respectively. There were multiple instances of additional neoplasms. Several factors were found to be of prognostic value (p < 0.05) for event-free (osteosarcoma site in the extremities) or overall (achievement of a surgical osteosarcoma-remission, receiving chemotherapy for the hematologic malignancy) survival. CONCLUSIONS: We were able to prove radiation therapy for hematological malignancies to be the predominant risk factor for later osteosarcomas. A resulting overrepresentation of axial and a tendency towards additional neoplasms affects prognosis. Still, selected patients may become long-term survivors with appropriate therapies, which is an argument against therapeutic negligence.
ABSTRACT
OBJECTIVES: The aim of this study was to introduce the MOCART 2.0 ankle score and evaluate its utility and reproducibility for the radiological assessment of cartilage repair tissue in the ankle joint. METHODS: The MOCART 2.0 ankle score evaluates seven individual variables, including "volume fill of (osteo)chondral defect," "Integration into adjacent cartilage and bone," "surface of the repair tissue," "signal intensity of the repair tissue," "bony defect and bony overgrowth," "presence of edema-like-marrow signal," and "presence of subchondral cysts." Overall, a MOCART 2.0 ankle score between 0 and 100 points may be reached. Two independent readers assessed the 3-T MRI examinations of 48 ankles, who had undergone cartilage repair of a talar cartilage defect using the new MOCART 2.0 ankle score. One of the readers performed two readings. Intra- and interrater reliability were assessed using intraclass correlation coefficients (ICCs) for the overall MOCART 2.0 ankle score. RESULTS: Forty-eight ankles (mean age at surgery 30.2 ± 11.2 years) were evaluated. The overall interrater (ICC = 0.75; 95%CI 0.60-0.85), as well as the intrarater (ICC = 0.83; 95%CI 0.72-0.90) reliability of the MOCART 2.0 ankle score was good. For individual variables the interrater reliability ranged from a kappa value of 0.29 (95%CI 0.01-0.57) for "surface of the repair tissue" to 0.83 (95%CI 0.71-0.95) for "presence of subchondral cysts". CONCLUSIONS: The newly introduced MOCART 2.0 ankle score, which encompasses the distinct anatomy of the ankle joint, demonstrates good intra- and interrater reliability. CRITICAL RELEVANCE STATEMENT: The newly introduced MOCART 2.0 ankle score may facilitate the standardized assessment of cartilage repair in the ankle joint and allow an objective comparison of the morphological outcome between alternative treatment options and between different studies. KEY POINTS: This study introduces the MOCART 2.0 ankle score. The MOCART 2.0 ankle score demonstrated good intra- and interrater reliability. Standardized reporting may improve communication between radiologists and other physicians.
ABSTRACT
BACKGROUND: Currently, povidone-iodine (PVP-I) and hydrogen peroxide (H2O2) are frequently used antiseptics in joint infections, but the cytotoxic effects of these solutions are already reported. N-chlorotaurine (NCT) shows a broad-spectrum bactericidal activity and is well tolerated in various tissues, but its effect on human chondrocytes is unknown. The purpose of this study was to assess the cytotoxic effect of NCT, PVP-I, and H2O2 on human chondrocytes compared to a control group in an in vitro setting to get first indications if NCT might be a promising antiseptic in the treatment of septic joint infections for the future. MATERIAL AND METHODS: Chondrocytes extracted from human cartilage were incubated with various concentrations of NCT, PVP-I, and H2O2 for 5 and 30 min respectively. EZ4U cell viability kit was used according to the manufacturer's recommendations determining cell viability. To assess cell viability based on their nuclear morphology, cells were stained with acridine-orange and identified under the fluorescence microscope. RESULTS: EZ4U kit showed after 5 and 30 min of incubation a significant decrease in cell viability at NCT 1%, NCT 0.1%, PVP-I, and H2O2, but not for NCT 0.001% and NCT 0.01%. Acridine-orange staining likewise presented a significant decrease in vital cells for all tested solutions except NCT 0.001% and NCT 0.01% after 5 and 30 min of incubation. CONCLUSION: Our results demonstrate that NCT is well tolerated by chondrocytes in vitro at the tested lower NCT concentrations 0.01% and 0.001% in contrast to the higher NCT concentrations 1% and 0.1%, PVP-I (1.1%), and H2O2 (3%), for which a significant decrease in cell viability was detected. Considering that the in vivo tolerability is usually significantly higher, our findings could be an indication that cartilage tissue in vivo would tolerate the already clinically used 1% NCT solution. In combination with the broad-spectrum bactericidal activity, NCT may be a promising antiseptic for the treatment of septic joint infections.
Subject(s)
Anti-Infective Agents, Local , Cell Survival , Chondrocytes , Hydrogen Peroxide , Povidone-Iodine , Taurine , Chondrocytes/drug effects , Humans , Taurine/pharmacology , Taurine/analogs & derivatives , Anti-Infective Agents, Local/pharmacology , Anti-Infective Agents, Local/toxicity , Hydrogen Peroxide/toxicity , Hydrogen Peroxide/pharmacology , Cell Survival/drug effects , Povidone-Iodine/pharmacology , Cells, Cultured , Dose-Response Relationship, DrugABSTRACT
Aims: Histology is widely used for diagnosis of persistent infection during reimplantation in two-stage revision hip and knee arthroplasty, although data on its utility remain scarce. Therefore, this study aims to assess the predictive value of permanent sections at reimplantation in relation to reinfection risk, and to compare results of permanent and frozen sections. Methods: We retrospectively collected data from 226 patients (90 hips, 136 knees) with periprosthetic joint infection who underwent two-stage revision between August 2011 and September 2021, with a minimum follow-up of one year. Histology was assessed via the SLIM classification. First, we analyzed whether patients with positive permanent sections at reimplantation had higher reinfection rates than patients with negative histology. Further, we compared permanent and frozen section results, and assessed the influence of anatomical regions (knee versus hip), low- versus high-grade infections, as well as first revision versus multiple prior revisions on the histological result at reimplantation. Sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV), chi-squared tests, and Kaplan-Meier estimates were calculated. Results: Overall, the reinfection rate was 18%. A total of 14 out of 82 patients (17%) with positive permanent sections at reimplantation experienced reinfection, compared to 26 of 144 patients (18%) with negative results (p = 0.996). Neither permanent sections nor fresh frozen sections were significantly associated with reinfection, with a sensitivity of 0.35, specificity of 0.63, PPV of 0.17, NPV of 0.81, and accuracy of 58%. Histology was not significantly associated with reinfection or survival time for any of the analyzed sub-groups. Permanent and frozen section results were in agreement for 91% of cases. Conclusion: Permanent and fresh frozen sections at reimplantation in two-stage revision do not serve as a reliable predictor for reinfection.
Subject(s)
Arthroplasty, Replacement, Hip , Arthroplasty, Replacement, Knee , Hip Prosthesis , Knee Prosthesis , Prosthesis-Related Infections , Humans , Arthroplasty, Replacement, Knee/adverse effects , Arthroplasty, Replacement, Knee/methods , Knee Prosthesis/adverse effects , Arthroplasty, Replacement, Hip/adverse effects , Arthroplasty, Replacement, Hip/methods , Hip Prosthesis/adverse effects , Prosthesis-Related Infections/diagnosis , Prosthesis-Related Infections/etiology , Prosthesis-Related Infections/surgery , Retrospective Studies , Reinfection , Knee Joint/surgery , Reoperation/methodsABSTRACT
The introduction of three-dimensional (3D) printed anatomical models has garnered interest in pre-operative planning, especially in orthopedic and trauma surgery. Identifying potential error sources and quantifying their effect on the model dimensional accuracy are crucial for the applicability and reliability of such models. In this study, twenty radii were extracted from anatomic forearm specimens and subjected to osteotomy to simulate a defined fracture of the distal radius (Colles' fracture). Various factors, including two different computed tomography (CT) technologies (energy-integrating detector (EID) and photon-counting detector (PCD)), four different CT scanners, two scan protocols (i.e., routine and high dosage), two different scan orientations, as well as two segmentation algorithms were considered to determine their effect on 3D model accuracy. Ground truth was established using 3D reconstructions of surface scans of the physical specimens. Results indicated that all investigated variables significantly impacted the 3D model accuracy (p < 0.001). However, the mean absolute deviation fell within the range of 0.03 ± 0.20 to 0.32 ± 0.23 mm, well below the 0.5 mm threshold necessary for pre-operative planning. Intra- and inter-operator variability demonstrated fair to excellent agreement for 3D model accuracy, with an intra-class correlation (ICC) of 0.43 to 0.92. This systematic investigation displayed dimensional deviations in the magnitude of sub-voxel imaging resolution for all variables. Major pitfalls included missed or overestimated bone regions during the segmentation process, necessitating additional manual editing of 3D models. In conclusion, this study demonstrates that 3D bone fracture models can be obtained with clinical routine scanners and scan protocols, utilizing a simple global segmentation threshold, thereby providing an accurate and reliable tool for pre-operative planning.
Subject(s)
Imaging, Three-Dimensional , Tomography, X-Ray Computed , Humans , Tomography, X-Ray Computed/methods , Imaging, Three-Dimensional/methods , Models, Anatomic , Radius Fractures/diagnostic imaging , Radius Fractures/surgery , Reproducibility of Results , Algorithms , Fractures, Bone/diagnostic imaging , Fractures, Bone/surgeryABSTRACT
BACKGROUND: Additively manufactured (AM) anatomical bone models are primarily utilized for training and preoperative planning purposes. As such, they must meet stringent requirements, with dimensional accuracy being of utmost importance. This study aimed to evaluate the precision and accuracy of anatomical bone models manufactured using three different AM technologies: digital light processing (DLP), fused deposition modeling (FDM), and PolyJetting (PJ), built in three different part orientations. Additionally, the study sought to assess surgeons' perceptions of how well these models mimic real bones in simulated osteosynthesis. METHODS: Computer-aided design (CAD) models of six human radii were generated from computed tomography (CT) imaging data. Anatomical models were then manufactured using the three aforementioned technologies and in three different part orientations. The surfaces of all models were 3D-scanned and compared with the original CAD models. Furthermore, an anatomical model of a proximal femur including a metastatic lesion was manufactured using the three technologies, followed by (mock) osteosynthesis performed by six surgeons on each type of model. The surgeons' perceptions of the quality and haptic properties of each model were assessed using a questionnaire. RESULTS: The mean dimensional deviations from the original CAD model ranged between 0.00 and 0.13 mm with maximal inaccuracies < 1 mm for all models. In surgical simulation, PJ models achieved the highest total score on a 5-point Likert scale ranging from 1 to 5 (with 1 and 5 representing the lowest and highest level of agreement, respectively), (3.74 ± 0.99) in the surgeons' perception assessment, followed by DLP (3.41 ± 0.99) and FDM (2.43 ± 1.02). Notably, FDM was perceived as unsuitable for surgical simulation, as the material melted during drilling and sawing. CONCLUSIONS: In conclusion, the choice of technology and part orientation significantly influenced the accuracy and precision of additively manufactured bone models. However, all anatomical models showed satisfying accuracies and precisions, independent of the AM technology or part orientation. The anatomical and functional performance of FDM models was rated by surgeons as poor.
ABSTRACT
BACKGROUND: Persistent knee synovitis leads to joint discomfort, incapacitating inflammation, and functional limitations. The conventional approach has involved surgical procedures to eliminate the actively inflamed synovial membrane. This study aims to investigate the recurrence-free survival and functional outcome after synovectomy and subsequent radiosynoviorthesis (RSO) in patients with knee synovitis. METHODS: Thirty-seven knees diagnosed with pigmented villonodular synovitis (PVNS), rheumatoid arthritis (RA), and peripheral spondyloarthritis underwent synovectomy and subsequent RSO between May 2005 and October 2016. The mean age was 34.9 ± 15.1 years, and the mean follow-up period was 84 ± 36.4 months. Clinical outcomes were assessed using the Oxford Knee Score and the presence of swelling and pain at the last follow-up. Recurrence-free survival denotes the duration from synovectomy to surgical re-synovectomy. RESULTS: In general, twelve knees underwent re-synovectomy after a mean follow-up of 34.8 ± 24.9 months. The recurrence-free survival was 83.8% at two years, 71.3% at five years, and 61.7% at ten years. The subgroup analysis revealed recurrence-free survival at two years in 63.6% of patients with PVNS, 86.7% of those with RA, and 100% of individuals with peripheral spondyloarthritis. CONCLUSIONS: This study demonstrates that combined therapy for synovitis is an effective approach, significantly improving clinical outcomes.
ABSTRACT
BACKGROUND: The importance of meniscal repair is widely accepted because of the association of loss of meniscal tissue with the development of early-onset knee arthritis. Many factors influencing the results of meniscal repair have been reported, but results remain controversial. PURPOSE: This meta-analysis determines the pooled meniscal repair failure rate of studies with a minimum follow-up of 2 years up to 5 years, with a mean follow-up of 43 months. Moreover, selected failure-influencing factors are analyzed. STUDY DESIGN: Systematic review and meta-analysis; Level of evidence, 4. METHODS: PubMed and Scopus were searched for studies published between January 2000 and November 2021 reporting on meniscal repair outcome with a minimum follow-up of 24 months. The overall pooled failure rate and pooled failure rates for possible predictors were calculated. Random-effect models were used to pool failure rates, and effect estimates in the form of odds ratios with 95% CIs were established. RESULTS: The initial literature search identified 6519 studies. A total of 51 studies met the inclusion criteria. In total, 3931 menisci were included with an overall failure rate of 14.8%. Subgroup analysis revealed a significantly lower failure rate for meniscal repair with concomitant anterior cruciate ligament (ACL) reconstruction compared with knees without any reported injury to the ACL (8.5% vs 14%; P = .043). The pooled failure rate for lateral meniscal repair was significantly lower than that for medial meniscal repair (6.1% vs 10.8%; P = .031). Pooled failure rates of all-inside and inside-out repair were not significantly different (11.9% vs 10.6%; P > .05). CONCLUSION: This meta-analysis on close to 4000 patients demonstrates an overall meniscal repair failure rate of 14.8% at a minimum follow-up from 2 years up to 5 years. Meniscal repair remains a procedure with a high failure rate, especially within the first 2 postoperative years. This review and meta-analysis also identified clinically relevant factors associated with favorable outcomes such as concomitant ACL reconstruction or repair of the lateral meniscus. All-inside meniscal repair with the latest-generation devices yields failure rates of <10%. The failure mechanism and the time of failure is poorly documented; further studies are needed for a better understanding of the retear mechanism.
Subject(s)
Anterior Cruciate Ligament Reconstruction , Arthroplasty, Replacement, Knee , Humans , Follow-Up Studies , Knee Joint , Menisci, Tibial/surgeryABSTRACT
PURPOSE: The Chiari pelvic osteotomy was the first surgical procedure to address hip dysplasia by changing the position of the acetabulum by medialization, thus creating a bony roof and improving biomechanical conditions. The aim of this retrospective cohort study was to report on the very long-term results of this technique. METHODS: Out of a consecutive series of 1536 hips, 504 in 405 patients were available for follow-up. The patients were assessed by physical and radiological examination. A Kaplan-Meier survival analysis with total hip arthroplasty as an endpoint was performed and stratified for age groups, pre-operative diagnosis, sex and osteoarthritis stage. RESULTS: The average follow-up was 36 ± 8.1 years (range, 35.2 to 54). The average pain level on the Visual Analogue Scale was 2.9 ± 2.6 (range 0 to 8.7). The average Harris Hip Score was 80.2 ± 17.4 (range 17.4 to 100). Correction of dysplasia was effective and remained stable over time. Osteoarthritis significantly increased over time with 53% Tönnis grade 3 at follow-up. The cumulative survivorship was 79.8% (95% confidence interval (CI), 76.1-83.2%) at 20 years, 57.1% (95% CI, 52.8-61.8%) at 30 years and 35% (95% CI, 30.3-40.3%) at 40 years. Young age, male sex and low osteoarthritis grade were positive prognostic factors. CONCLUSIONS: Although the Chiari pelvic osteotomy is considered a salvage procedure nowadays, it achieved excellent long-term results even in indications, which would be treated differently today. Young patients without osteoarthritis had the best outcome.
Subject(s)
Hip Dislocation, Congenital , Hip Dislocation , Osteoarthritis, Hip , Humans , Male , Hip Dislocation/surgery , Follow-Up Studies , Retrospective Studies , Treatment Outcome , Hip Dislocation, Congenital/surgery , Acetabulum/surgery , Osteoarthritis, Hip/etiology , Osteoarthritis, Hip/surgery , Osteotomy/adverse effects , Osteotomy/methodsABSTRACT
OBJECTIVE: To investigate whether biological DMARDs affect the risk of aseptic loosening after total hip/knee arthroplasty (THA/TKA) in patients with RA. METHODS: We retrospectively identified all patients suffering from RA who underwent THA/TKA at our academic centre between 2002 and 2015 and linked them with an existing prospective observational RA database at our institution. The risk of aseptic loosening was estimated using radiological signs of component loosening (RCL). A time-dependent Cox regression analysis was used to compare the risk of implant loosening between patients treated with traditional DMARDS and biological DMARDs, or alternately both over time. RESULTS: A total of 155 consecutive total joint arthroplasties (TJAs) (103 TKA vs 52 THA) was retrospectively included in the study. Mean age at implantation was 59 ± 13 years. Mean follow-up time was 69 ± 43 months. Overall, 48 (31%) TJAs showed signs of RCL, with 28 (27.2%) RCLs occurring after TKA compared with 20 after THA (38.5%). A significant difference regarding the incidence of RCL between the traditional DMARDs group (39 cases of RCL, 35%) and the biological DMARDs group (nine cases of RCL, 21%) (P = 0.026) was observed using the log-rank test. This was also true when using a time-dependent Cox regression with therapy as well as arthroplasty location (hip vs knee) as variables (P = 0.0447). CONCLUSION: Biological DMARDs may reduce the incidence of aseptic loosening after TJA in patients with RA compared with traditional DMARDs. This effect seems to be more pronounced after TKA than THA.
Subject(s)
Antirheumatic Agents , Arthroplasty, Replacement, Hip , Arthroplasty, Replacement, Knee , Humans , Middle Aged , Aged , Retrospective Studies , Arthroplasty, Replacement, Hip/adverse effects , Regression Analysis , Antirheumatic Agents/therapeutic use , Reoperation , Prosthesis FailureABSTRACT
BACKGROUND: Meta-diaphyseal fixation of straight, tapered, uncemented stems has been proven to be very reliable for total hip arthroplasty in 10 to 20 years of follow-up studies. The aim of the study was to evaluate whether the implant survival as well as radiological and functional outcome have changed in patients with a minimum follow-up of 30 years. METHODS: From a total of 210 patients, who received a straight, rectangular, tapered cementless stem and a threaded cup, there were 37 total hip arthroplasties (33 patients) still available for follow-up after a minimum of 30 years. Patients were examined clinically and radiographically, and revision surgeries were recorded. RESULTS: There was a low rate of revisions of the femoral stem with a survival probability of 0.92 (confidence interval 0.85 to 0.96) at 30 years. Survival probability of the acetabular component decreased drastically with 0.45 (confidence interval 0.30 to 0.59). Radiographic analysis of the stem revealed radiolucencies in 73% (n = 16), but only in the proximal/metaphyseal part and none of the stems were radiographically loose. CONCLUSION: In this minimum 30-year follow-up study, a straight rectangular cementless implant continues to provide excellent implant survival and high patient satisfaction. However, survival rates of the whole total hip replacement system were reduced by a high revision rate due to wear-related problems.
Subject(s)
Arthroplasty, Replacement, Hip , Hip Prosthesis , Humans , Follow-Up Studies , Hip Prosthesis/adverse effects , Treatment Outcome , Prosthesis Design , Prosthesis Failure , Arthroplasty, Replacement, Hip/adverse effects , Acetabulum , ReoperationABSTRACT
OBJECTIVES: Early, accurate diagnosis is crucial for the prognosis of patients with soft tissue sarcomas. To this end, standardization of imaging algorithms, technical requirements, and reporting is therefore a prerequisite. Since the first European Society of Musculoskeletal Radiology (ESSR) consensus in 2015, technical achievements, further insights into specific entities, and the revised WHO-classification (2020) and AJCC staging system (2017) made an update necessary. The guidelines are intended to support radiologists in their decision-making and contribute to interdisciplinary tumor board discussions. MATERIALS AND METHODS: A validated Delphi method based on peer-reviewed literature was used to derive consensus among a panel of 46 specialized musculoskeletal radiologists from 12 European countries. Statements were scored online by level of agreement (0 to 10) during two iterative rounds. Either "group consensus," "group agreement," or "lack of agreement" was achieved. RESULTS: Eight sections were defined that finally contained 145 statements with comments. Overall, group consensus was reached in 95.9%, and group agreement in 4.1%. This communication contains the first part consisting of the imaging algorithm for suspected soft tissue tumors, methods for local imaging, and the role of tumor centers. CONCLUSION: Ultrasound represents the initial triage imaging modality for accessible and small tumors. MRI is the modality of choice for the characterization and local staging of most soft tissue tumors. CT is indicated in special situations. In suspicious or likely malignant tumors, a specialist tumor center should be contacted for referral or teleradiologic second opinion. This should be done before performing a biopsy, without exception. CLINICAL RELEVANCE: The updated ESSR soft tissue tumor imaging guidelines aim to provide best practice expert consensus for standardized imaging, to support radiologists in their decision-making, and to improve examination comparability both in individual patients and in future studies on individualized strategies. KEY POINTS: ⢠Ultrasound remains the best initial triage imaging modality for accessible and small suspected soft tissue tumors. ⢠MRI is the modality of choice for the characterization and local staging of soft tissue tumors in most cases; CT is indicated in special situations. Suspicious or likely malignant tumors should undergo biopsy. ⢠In patients with large, indeterminate or suspicious tumors, a tumor reference center should be contacted for referral or teleradiologic second opinion; this must be done before a biopsy.
ABSTRACT
Osteoinductive BMPs require a suitable delivery system for treating various pathological conditions of the spine and segmental bone defects. INFUSE, the only commercially available BMP-based osteoinductive device, consisting of rhBMP2 on bovine absorbable collagen sponge (ACS) showed major disadvantages due to serious side effects. A novel osteoinductive device, OSTEOGROW, comprised of rhBMP6 dispersed within autologous blood coagulum (ABC) is a promising therapy for bone regeneration, subjected to several clinical trials for diaphysial bone repair and spinal fusion. In the present study, we have examined the release dynamics showing that the ABC carrier provided a slower, more steady BMP release in comparison to the ACS. Rat subcutaneous assay was employed to evaluate cellular events and the time course of ectopic osteogenesis. The host cellular response to osteoinductive implants was evaluated by flow cytometry, while dynamics of bone formation and maintenance in time were evaluated by histology, immunohistochemistry and micro CT analyses. Flow cytometry revealed that the recruitment of lymphoid cell populations was significantly higher in rhBMP6/ABC implants, while rhBMP2/ACS implants recruited more myeloid populations. Furthermore, rhBMP6/ABC implants more efficiently attracted early and committed progenitor cells. Dynamics of bone formation induced by rhBMP2/ACS was characterized by a delayed endochondral ossification process in comparison to rhBMP6/ABC implants. Besides, rhBMP6/ABC implants induced more ectopic bone volume in all observed time points in comparison to rhBMP2/ACS implants. These results indicate that OSTEOGROW was superior to INFUSE due to ABC's advantages as a carrier and rhBMP6 superior efficacy in inducing bone.
Subject(s)
Ossification, Heterotopic , Osteogenesis , Rats , Animals , Cattle , Collagen/pharmacology , Transforming Growth Factor beta/pharmacology , Bone Morphogenetic Proteins , Bone Regeneration , Recombinant Proteins/pharmacologyABSTRACT
While previous studies on navigated total hip replacement (nTHA) focused on acetabular component positioning, we compared the results of nTHA with conventional total hip replacement (cTHA) in respect of changes in leg length and hip offset. In a single-center study results radiographic parameters of patients with unilateral THA were included. Data were retrospectively analyzed from computer navigation data and radiographs. Analysis concentrated on the discrepancy in leg length (LLD) and hip offset (OSD) between the affected and unaffected hip. The effect of the procedure was defined as the difference between postoperative and preoperative LLD and OSD values in each group. 2332 patients were analyzed. Both nTHA and cTHA were effective in restoring LLD and OSD by reducing the preoperative value significantly (p < 0.001). Regarding changes in LLD, no statistical difference between nTHA and cTHA could be found. Changes in OSD nTHA was a slightly more effective than cTHA (- 2.06 ± 6.00 mm vs. - 1.50 ± 5.35 mm; p < 0.05). Both navigated and conventional THA were successful in reconstruction of leg length and hip offset, while postoperative offset discrepancy was significantly lower in the navigated group at the cost of longer operation times. If these results are clinically relevant further investigation is needed.
Subject(s)
Arthroplasty, Replacement, Hip , Hip Prosthesis , Humans , Arthroplasty, Replacement, Hip/methods , Leg/surgery , Retrospective Studies , Leg Length Inequality/diagnostic imaging , Leg Length Inequality/surgery , Acetabulum/surgeryABSTRACT
Several authors observed a loss of correction after performing Chiari pelvic osteotomy (CPO) in young patients. Hence, the aim of this study was to answer two questions: (1) Does the Chiari pelvic osteotomy affect the development of the acetabulum in skeletally immature patients in the long term? (2) Is there any evidence of the previously described "Anti-Chiari" effect after a mean follow-up of 36 years? Data from 21 patients (27 hips) undergoing CPO before the age of 16 years were clinically assessed, and the evolution of radiological parameters over time was analyzed. The mean age at CPO was 11.2 years (±3; 4.4-15.7). The 20- and 30-year survival rates of the CPO were 100% and 92.6%, respectively. Mean postoperative medialization was 54% (±18; 23-99). The average osteotomy angle was 11° (±7; 2-28). No significant changes were found for the center-edge angle (CEA) and acetabular index (AI) over time; the angle of Idelberger and Frank (ACM) almost reached normal values at follow-up (FU); for the acetabular-head index (AHI), a slight shift toward the initial situation could be detected. The morphology of the acetabulum remained unchanged over time. The "Anti-Chiari effect" seems to be primarily caused by insufficient coverage of the femoral head rather than damage to the apophysis due to surgery.
ABSTRACT
Due to its high printing resolution and ability to print multiple materials simultaneously, inkjet technology has found wide application in medicine. However, the biological safety of 3D-printed objects is not always guaranteed due to residues of uncured resins or support materials and must therefore be verified. The aim of this study was to evaluate the quality of standard assessment methods for determining the quality and properties of polyjet-printed scaffolds in terms of their dimensional accuracy, surface topography, and cytotoxic potential.Standardized 3D-printed samples were produced in two printing orientations (horizontal or vertical). Printing accuracy and surface roughness was assessed by size measurements, VR-5200 3D optical profilometer dimensional analysis, and scanning electron microscopy. Cytotoxicity tests were performed with a representative cell line (L929) in a comparative laboratory study. Individual experiments were performed with primary cells from clinically relevant tissues and with a Toxdent cytotoxicity assay.Dimensional measurements of printed discs indicated high print accuracy and reproducibility. Print accuracy was highest when specimens were printed in horizontal direction. In all cytotoxicity tests, the estimated mean cell viability was well above 70% (p < 0.0001) regardless of material and printing direction, confirming the low cytotoxicity of the final 3D-printed objects.