Efficient degradation of sulfonamides by introducing sulfur to magnetic Prussian blue analog in photo-assisted persulfate oxidation system.

The peroxynitrite photocatalytic degradation system was considered a green, convenient, and efficient water treatment process, but not satisfying against some antibiotics, e.g. sulfonamides (SAs). To improve the photocatalytic degradation efficiency of SAs, sulfur was introduced to a magnetic Fe-MOF (Fe-metal organic framework) Prussian blue analog to achieve a heteroatomic material CuFeO@S, which was applied in heterogeneous visible light photo-assisted catalytic process with persulfate (PS) as an oxidant. The characterization results of CuFeO@S by XRD and XPS confirmed the presence of Fe3O4 (for magnetic separation), Cu+ (for activation of PS) and S2- (for narrowing the energy band and prolonging the lifetime of photo-generated electronics). Through systematic optimization of reaction conditions in CuFeO@S + PS + hv system, efficient degradation of four tested SAs was achieved in 30 min (removal rate of 97-100% for the tested 4 SAs). Moreover, the material could be magnetically recycled and reused for over 7 cycles with a removal rate of >90% for sulfamerazine. Furthermore, the removal rate of sulfamerazine in pond water reached 99% at a mineralization rate of about 34% (decrease in total organic matter), demonstrating its potential in the treatment of antibiotic-containing wastewater.

Quantification and Characterization of Fine Plastic Particles as Considerable Components in Atmospheric Fine Particles.

The negative effects of air pollution, especially fine particulate matter (PM2.5, particles with an aerodynamic diameter of ≤2.5 µm), on human health, climate, and ecosystems are causing significant concern. Nevertheless, little is known about the contributions of emerging pollutants such as plastic particles to PM2.5 due to the lack of continuous measurements and characterization methods for atmospheric plastic particles. Here, we investigated the levels of fine plastic particles (FPPs) in PM2.5 collected in urban Shanghai at a 2 h resolution by using a novel versatile aerosol concentration enrichment system that concentrates ambient aerosols up to 10-fold. The FPPs were analyzed offline using the combination of spectroscopic and microscopic techniques that distinguished FPPs from other carbon-containing particles. The average FPP concentrations of 5.6 µg/m3 were observed, and the ratio of FPPs to PM2.5 was 13.2% in this study. The FPP sources were closely related to anthropogenic activities, which pose a potential threat to ecosystems and human health. Given the dramatic increase in plastic production over the past 70 years, this study calls for better quantification and control of FPP pollution in the atmosphere.

A proteomic study on gastric impairment in rats caused by microcystin-LR.

Microcystins (MCs) are the most common cyanobacterial toxins. Epidemiological investigation showed that exposure to MCs can cause gastro-intestinal symptoms, gastroenteritis and gastric cancer. MCs can also accumulate in and cause histopathological damage to stomach. However, the exact mechanisms by which MCs cause gastric injury were unclear. In this study, Wistar rats were administrated 50, 75 or 100 µg microcystin-LR (MC-LR)/kg, body mass (bm) via tail vein, and histopathology, response of anti-oxidant system and the proteome of gastric tissues at 24 h after exposure were studied. Bleeding of fore-stomach and gastric corpus, inflammation and necrosis in gastric corpus and exfoliation of mucosal epithelial cells in gastric antrum were observed following acute MC-LR exposure. Compared with controls, activities of superoxide dismutase (SOD) were significantly greater in gastric tissues of exposed rats, while activities of catalase (CAT) were less in rats administrated 50 µg MC-LR/kg, bm, and concentrations of glutathione (GSH) and malondialdehyde (MDA) were greater in rats administrated 75 or 100 µg MC-LR/kg, bm. These results indicated that MC-LR could disrupt the anti-oxidant system and cause oxidative stress. The proteomic results revealed that MC-LR could affect expressions of proteins related to cytoskeleton, immune system, gastric functions, and some signaling pathways, including platelet activation, complement and coagulation cascades, and ferroptosis. Quantitative real-time PCR (qRT-PCR) analysis showed that transcriptions of genes for ferroptosis and gastric function were altered, which confirmed results of proteomics. Overall, this study illustrated that MC-LR could induce gastric dysfunction, and ferroptosis might be involved in MC-LR-induced gastric injury. This study provided novel insights into mechanisms of digestive diseases induced by MCs.

Colorimetric Detection of Multiple Phenols Based on Multifunctional Fe3 O4 /SnS2 Composites.

Phenols pose a great threat to human and environment due to their high toxicity and low bio-degradability. Therefore, the development of a rapid and sensitive detection method for multiple phenols is of great importance. Here, a colorimetric detection method based on Fe3 O4 /SnS2 composites was established for the detection and discrimination of ten phenols for the first time. The results demonstrated that the incorporation of the photo catalyst SnS2 significantly improved the peroxidase-like activity of Fe3 O4 , leading to an enhancing efficiency of the colorimetric detection method. The developed method was capable of detecting phenol within a concentration range of 0.5-2000 µM, with detection limit as low as 0.06 µM. This method was successfully applied to detect total phenols in samples obtained from two sewage treatment plants and seawater. Furthermore, by employing principal component analysis, the established colorimetric method enabled the simultaneous discrimination of all ten phenols. The performance was further evaluated by accurately identifying binary or ternary mixtures of phenols, and even identifying the type of phenol in 10 unknown samples containing one of the ten phenols. These findings highlight the potential of the Fe3 O4 /SnS2 composite as a promising candidate for the simultaneous detection of multiple phenols in liquid samples.

Rapid screening of benzyl dodecyl dimethyl ammonium bromide co-metabolic degrading bacteria based on NIR hyperspectral imaging technology.

As a typical disinfectant, the use of benzyl dodecyl dimethyl ammonium bromide (BDAB) has dramatically increased since the emergence of SARS-CoV-2, posing a threat to environmental balance and human health. Screening BDAB co-metabolic degrading bacteria is required for efficient microbial degradation. Conventional methods for screening co-metabolic degrading bacteria are laborious and time-consuming, especially when the number of strains is large. This study aimed to develop a novel method for the rapid screening of BDAB co-metabolic degrading bacteria from the cultured solid medium using near-infrared hyperspectral imaging (NIR-HSI) technology. Based on NIR spectra, the concentration of BDAB in the solid medium can be well predicted by partial least squares regression (PLSR) models, non-destructively and rapidly, with Rc2 > 0.872 and Rcv2 > 0.870. The results show that the predicted BDAB concentrations decrease after degrading bacteria utilization, comparing with the regions where no degrading bacteria grew. The proposed method was applied to directly identify the BDAB co-metabolic degrading bacteria cultured on the solid medium, and two kinds of co-metabolic degrading bacteria RQR-1 and BDAB-1 were correctly identified. This method provides a high-efficiency method for screening BDAB co-metabolic degrading bacteria from a large number of bacteria.

From Medical Herb to Functional Food: Development of a Fermented Milk Containing Silybin and Protein from Milk Thistle.

Milk thistle is a traditional medicinal herb. Silybin is a medicinal component found in the seed coat of milk thistle, which has liver-protective and anti-cancer properties. Conventional studies have focused on the extraction of silybin with organic reagents, which was inapplicable to the food industry. This study aims to develop a fermented milk containing silybin and protein from the milk thistle seeds. A three step procedure was developed, comprising homogenization of milk thistle seeds, NaHCO3 heat treatment, and microbial fermentation. The silybin was characterized by high performance liquid chromatography, and the protein was quantified and electrophorized. It was found that the homogenization step was essential for the preparation of protein, and the NaHCO3 heat treatment was the crucial step in obtaining silybin. The optimal NaHCO3 treatment settings were 1% NaHCO3, 60°C, and 3 h, and the optimal strains for microbial fermentation were L131 (Rummeliibacillus stabekisii) and RS72 (Lactobacillus plantarum). The silybin yield in the fermented milk reached 11.24-12.14 mg/g seeds, accounting for 72.6-78.4% of the total silybin in the milk thistle seeds, and the protein yield reached 121.8-129.6 mg/g seeds. The fermented milk had a slightly sweet yoghurt-like flavor and could be used as a dietary supplement for silybin and protein.

Non-Destructive Extraction and Separation of Nano- and Microplastics from Environmental Samples by Density Gradient Ultracentrifugation.

Nano-/microplastics (NMPs, particle diameter < 5 mm) are widespread emerging pollutants causing diverse impacts on organisms due to their sizes, shapes, and chemical properties. Despite the fast increase in NMP research, an effective method to separate and identify NMP types from environmental samples is still lacking. Here, we developed a simple and effective approach for the non-destructive extraction and separation of various types of NMPs from environmental samples by density gradient ultracentrifugation (DGU). For the first time, DGU was capable to separate various NMPs from the complex matrix with high selectivity (100%), purity (93%), and applicability. Through a gradually changing density of the density gradient medium by changing the concentrations or volumes of CsCl/water solution (from 0.00065 to 0.01989 g cm-3 mm-1), various NMPs (with particle sizes as little as 50 nm) could be extracted and separated from soil samples with high recovery (78.5-96.0%). We confirmed the effectiveness and compatibility of DGU through a correct identification of all types of NMPs separated from artificial soil samples with Raman spectroscopy, simultaneous thermal analysis (STA), and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). DGU is compatible with all analytical processes compared to other existing methods with much less sample pretreatment time (0.5 h). Overall, DGU is an effective and cheap method (2.2 USD/sample) to separate NMPs from environmental samples such as soil and water and, hence, can facilitate research on NMPs related to terrestrial and marine environments as well as human health.

Identification and characterization of Fe3O4/peroxodisulfate advanced oxidation products from sulfameter.

Sulfonamides (SAs) are one of the most widely used antibiotics and their residuals in the environment could cause some negative environmental issues. Advanced oxidation such as Fenton-like reaction has been widely applied in the treatment of SAs polluted water. Degradation rates of 95%-99.7% were achieved in this work for the tested 8 SAs, including sulfisomidine, sulfameter (SME), phthalylsulfathiazole, sulfamethoxypyridazine, sulfamonomethoxine, sulfisoxazole, sulfachloropyridazine, and sulfadimethoxine, in the Fe3O4/peroxodisulfate (PDS) oxidation system after the optimization of PDS concentration and pH. Meanwhile, it was found that a lot of unknown oxidation products were formed, which brought up the uncertainty of health risks to the environment, and the identification of these unknown products was critical. Therefore, SME was selected as the model compound, from which the oxidation products were never elucidated, to identify these intermediates/products. With liquid chromatography-high resolution tandem mass spectrometry (LC-HRMS/MS), 10 new products were identified, in which 2-amino-5-methoxypyrimidine (AMP) was confirmed by its standard. The investigation of the oxidation process of SME indicated that most of the products were not stable and the degradation pathways were very complicated as multiple reactions, such as oxidation of the amino group, SO2 extrusion, and potential cross-reaction occurred simultaneously. Though most of the products were not verified due to the lack of standards, our results could be helpful in the evaluation of the treatment performance of SAs containing wastewater.

C/N-Dependent Element Bioconversion Efficiency and Antimicrobial Protein Expression in Food Waste Treatment by Black Soldier Fly Larvae.

The black soldier fly (BSF), Hermetia illucens, has emerged as a promising species for waste bioconversion and source of antimicrobial proteins (AMPs). However, there is a scarcity of research on the element transformation efficiency and molecular characterization of AMPs derived from waste management. Here, food waste treatment was performed using BSF larvae (BSFL) in a C/N ratio of 21:1−10:1, with a focus on the C/N-dependent element bioconversion, AMP antimicrobial activity, and transcriptome profiling. The C-larvae transformation rates were found to be similar among C/Ns (27.0−35.5%, p = 0.109), while the N-larvae rates were different (p = 0.001), with C/N 21:1−16:1 (63.5−75.0%) being higher than C/N 14:1−10:1 (35.0−45.7%). The C/N ratio did not alter the antimicrobial spectrum of AMPs, but did affect the activities, with C/N 21:1 being significantly lower than C/N 18:1−10:1. The lysozyme genes were found to be significantly more highly expressed than the cecropin, defensin, and attacin genes in the AMP gene family. Out of 51 lysozyme genes, C/N 18:1 and C/N 16:1 up-regulated (p < 0.05) 14 and 12 genes compared with C/N 21:1, respectively, corresponding to the higher activity of AMPs. Overall, the element bioconversion efficiency and AMP expression can be enhanced through C/N ratio manipulation, and the C/N-dependent transcriptome regulation is the driving force of the AMP difference.

Enhanced selective nitrate-to-nitrogen reduction by aerosol-assisted iron-carbon composites: Insights into the key factors.

In this study, an aerosol-assisted Fe0/C (carbon supported zero-valent iron) composite was prepared and evaluated, which could effectively remove nitrate and exhibit high nitrogen selectivity. The results show that the selectivity of nitrogen for freshly prepared Fe0/C composites could reach 52.2% when pH at 7, compared to that of 7.7% for traditional nZVI. Meanwhile, the removal efficiency of nitrate was slightly increased from 63.5% to 69.9%. Furthermore, a variety of methods such as SEM, TEM, XRD, XPS, BET, FTIR and TGA were used to characterize the Fe0/C composites before and after reaction. Hence, the following key factors were determined for the effective conversion from nitrate to nitrogen: the surface of zero valent iron particle should be protected from oxidation and its genuine characteristics are well retained; the reaction should be controlled under an anaerobic condition; and the carbon as the carrier to support iron particles is very important; lower initial pH favors nitrogen generation. Various materials including aged Fe0/C composites, Fe0/SiO2 (SiO2 supported zero-valent iron) composites and nZVI particles in the deoxygenated and oxygenated systems were assessed for comparison.

An Organic Solvent-Free Method for the Extraction of Ellagic Acid Compounds from Raspberry Wine Pomace with Assistance of Sodium Bicarbonate.

Industrial processing of raspberry juice and wine generates considerable byproducts of raspberry pomace. Ellagic acids/ellagitannins, being characterized by their antioxidant and antiproliferation properties, constitute the majority of polyphenolics in the pomace and are valuable for recovery. In the present study, we developed a novel procedure with sodium bicarbonate assisted extraction (SBAE) to recover ellagic acid from raspberry wine pomace. Key parameters in the procedure, i.e., sodium bicarbonate concentration, temperature, time and solid/liquid (S/L) ratio, were investigated by single factor analysis and optimized subsequently by Response Surface Methodology (RSM). Optimal parameters for the SBAE method here were found to be 1.2% (w/v) NaHCO3, 1:93 (w/v) S/L ratio, 22 min and 100 °C. Under these conditions, the ellagic acid yield was 6.30 ± 0.92 mg/g pomace with an antioxidant activity of 79.0 ± 0.96 µmol Trolox eq/g pomace (DPPH assay), which are 2.37 and 1.32 times the values obtained by extraction with methanol-acetone-water solvent, respectively. The considerable improvement in ellagic acid extraction efficiency could be highly attributed to the reactions of lipid saponification and ellagitannin hydrolysis resulted from sodium bicarbonates. The present study has established an organic solvent-free method for the extraction of ellagic acid from raspberry wine pomace, which is feasible and practical in nutraceutical applications.

Performance and bacterial community profiles of sequencing batch reactors during long-term exposure to polyethylene terephthalate and polyethylene microplastics.

Microplastics (MPs) are ubiquitous in wastewater treatment plants (WWTPs), but much remains to be learned about their roles in WWTPs. Herein, polyethylene terephthalate (PET) and polyethylene (PE) particles were added into sequencing batch reactors (SBRs), and the sole impacts and co-impacts of MPs with other pollutants (phenol and Cu2+) on wastewater treatment processes were evaluated. Results indicated that MPs did not significantly affect SBR performance, either alone or co-occurrence with phenol, but the co-exposure to MPs and Cu2+ severely suppressed COD removal efficiency by 37.02%-64.70%. The functional groups of activated sludge had no changes after receiving MPs, but the MPs-Cu2+ co-exposure could greatly promote the secretion of extracellular polymeric substances. Furthermore, MPs had no negative impacts on diversity, richness and structure of bacterial communities, and PET and PE showed different preferences for enrichment of bacterial populations. Moreover, the MPs-Cu2+ co-exposure obviously reduced the overall abundances of Cu-related genes in SBRs.

Catalytic performance and periodate activation mechanism of anaerobic sewage sludge-derived biochar.

Periodate (PI)-based advanced oxidation processes are a newly discovered approach for effective pollutant elimination. In this study, we demonstrated that biochar obtained from pyrolysis of anaerobic sewage sludge without any pretreatment can be used for PI activation. The biochar obtained at 800 °C (SBC-800) exhibited the best PI activation capacity using acid organic II (AO7) as substrate. The PI activation was strongly dependent on pH and exhibited the highest AO7 removal rate at pH 3.0. Meanwhile, the anti-interference capacity with common wastewater components and reusability of the SBC-800/PI system were confirmed. Combined with the results of chemical quenching, reactive oxygen species (ROS) trapping, X-ray photoelectric spectroscopy (XPS), electrochemical and density function theory (DFT)-based calculations, singlet oxygen production and electron transfer mediated by the SBC-800-PI complex were the dominant AO7 oxidation mechanisms. This study provides easily prepared catalysts for PI activation and paves the way for solid waste recycling and reuse.

Effects of Different Nitrogen Sources and Ratios to Carbon on Larval Development and Bioconversion Efficiency in Food Waste Treatment by Black Soldier Fly Larvae (Hermetia illucens).

Biowaste treatment by black soldier fly larvae (BSFL, Hermetia illucens) has received global research interest and growing industrial application. Larvae farming conditions, such as temperature, pH, and moisture, have been critically examined. However, the substrate carbon to nitrogen ratio (C/N), one of the key parameters that may affect larval survival and bioconversion efficiency, is significantly less studied. The current study aimed to compare the nitrogen supplying effects of 9 nitrogen species (i.e., NH4Cl, NaNO3, urea, uric acid, Gly, L-Glu, L-Glu:L-Asp (1:1, w/w), soybean flour, and fish meal) during food waste larval treatment, and further examine the C/N effects on the larval development and bioconversion process, using the C/N adjustment with urea from the initial 21:1 to 18:1, 16:1, 14:1, 12:1, and 10:1, respectively. The food wastes were supplied with the same amount of nitrogen element (1 g N/100 g dry wt) in the nitrogen source trial and different amount of urea in the C/N adjustment trial following larvae treatment. The results showed that NH4Cl and NaNO3 caused significant harmful impacts on the larval survival and bioconversion process, while the 7 organic nitrogen species resulted in no significant negative effect. Further adjustment of C/N with urea showed that the C/N range between 18:1 and 14:1 was optimal for a high waste reduction performance (73.5-84.8%, p < 0.001) and a high larvae yield (25.3-26.6%, p = 0.015), while the C/N range of 18:1 to 16:1 was further optimal for an efficient larval protein yield (10.1-11.1%, p = 0.003) and lipid yield (7.6-8.1%, p = 0.002). The adjustment of C/N influenced the activity of antioxidant enzymes, such as superoxide dismutase (SOD, p = 0.015), whereas exerted no obvious impact on the larval amino acid composition. Altogether, organic nitrogen is more suitable than NH4Cl and NaNO3 as the nitrogen amendment during larval food waste treatment, addition of small amounts of urea, targeting C/N of 18:1-14:1, would improve the waste reduction performance, and application of C/N at 18:1-16:1 would facilitate the larval protein and lipid bioconversion process.

Assembly of fungal mycelium-carbon nanotube composites and their application in pyrene removal.

Polycyclic aromatic hydrocarbons (PAHs) have been known for decades to threaten human health. Various physical, chemical and biological methods have been developed to remove PAHs from different matrices. Microbial biodegradation processes are thought to be effective and environmentally friendly, but the low bioavailability of PAHs and their slow removal rate often limit the application of biodegradation. In this study, novel self-assembled PAH-degrading fungal mycelium (Penicillium oxalicum SYJ-1)-carbon nanotube (CNT) composites were applied for pyrene removal. The addition of CNTs did not affect the growth of strain SYJ-1 and promoted the total PAH removal efficiency. The composite could completely remove pyrene at 20 mg L-1 within 48 h, while the sole fungus and CNTs alone could only remove 72% and 80% of pyrene at 72 h, respectively. A cytochrome P450 inhibition experiment, together with degradation product identification and transcriptomic analysis, suggested that an intracellular PAH transformation pathway was employed by strain SYJ-1. The versatility of this assembly approach was also confirmed by adding different nanomaterials and using them to remove different pollutants. This study provides a strategy of coupling the chemical adsorption and biodegradation capacity of inorganic nanomaterials and microorganisms as composites to treat hydrophobic substrates in restricted bioreactor.

Effect of Polystyrene Microplastics of Different Sizes to Escherichia coli and Bacillus cereus.

The toxicity of polystyrene (PS) particles of different sizes was investigated using Gram-negative Escherichia coli and Gram-positive Bacillus cereus. PS particles could inhibit the cell growth of E. coli but promote the cell growth of B. cereus, and this difference might be attributed to different composition in their cell walls and the different interactions between the two bacteria and PS particles. Direct adhesion of E. coli cells on the surface of 5 µm PS microbeads by flagella was observed, indicating the putative role of E. coli on biofilm formation of plastisphere. The regulations of malondialdehyde, lactate dehydrogenase and glutathione were similar between the two bacteria, so the difference in the toxicity effect of PS between the two bacteria was not caused by the antioxidant activity. The overall results of the present study could help to understand the responses of different bacteria to microplastic exposure.

Identification of chloramination disinfection by-products from phenylalanine in tap drinking water.

Phenylalanine (Phe) is widely present in natural water and serves as a precursor of disinfection by-products (DBPs). We reported the identification of chloramination DBPs from Phe in drinking water using ultra-high performance liquid chromatography (UHPLC) coupled with complementary high-resolution quadrupole time-of-flight (QTOF) and triple quadrupole (tQ) tandem mass spectrometry (MS/MS). In the chloraminated Phe water solution, sixteen new DBPs in a total of seventeen were identified based on their accurate mass, MS/MS spectra and 35Cl/37Cl isotopic patterns. Three of these DBPs were verified as benzamide, phenylacetamide, and p-hydroxyphenylacetamide with their standards, while the others were chlorinated derivatives of Phe, hydrazone, amidine, amide and peroxide, in which the unique structures of these DBPs were rarely reported. Their stability and formation process were investigated as well. Furthermore, a method consisting of solid phase extraction (SPE) and UHPLC-MS/MS using dynamic multiple reaction monitoring (dMRM) was developed to investigate these DBPs in authentic waters. Phe, benzamide, phenylacetamide, and N-Cl-2-phenylacetimidamide were detected in chlorinated tap water. Compared with the other identified DBPs, these three DBPs were exceptionally stable and could be formed in wide formation conditions. Our work not only provided ideas for the identification of new chloramination DBPs, but also demonstrated that some DBPs usually generated in the chloramination disinfection process could also be found in the chlorinated drinking water.

Molecular mechanisms of zooplanktonic toxicity in the okadaic acid-producing dinoflagellate Prorocentrum lima.

Prorocentrum lima is a dinoflagellate that forms hazardous blooms and produces okadaic acid (OA), leading to adverse environmental consequences associated with the declines of zooplankton populations. However, little is known about the toxic effects and molecular mechanisms of P. lima or OA on zooplankton. Here, their toxic effects were investigated using the brine shrimp Artemia salina. Acute exposure of A. salina to P. lima resulted in lethality at concentrations 100-fold lower than densities observed during blooms. The first comprehensive results from global transcriptomic and metabolomic analyses in A. salina showed up-regulated mRNA expression of antioxidant enzymes and reduced non-enzyme antioxidants, indicating general detoxification responses to oxidative stress after exposure to P. lima. The significantly up-regulated mRNA expression of proteasome, spliceosome, and ribosome, as well as the increased fatty acid oxidation and oxidative phosphorylation suggested the proteolysis of damaged proteins and induction of energy expenditure. Exposure to OA increased catabolism of chitin, which may further disrupt the molting and reproduction activities of A. salina. Our data shed new insights on the molecular responses and toxicity mechanisms of A. salina to P. lima or OA. The simple zooplankton model integrated with omic methods provides a sensitive assessment approach for studying hazardous algae.

Determination of phenolic compounds in estuary water and sediment by solid-phase isotope dansylation coupled with liquid chromatography-high resolution mass spectrometry.

A method consisting of solid-phase isotope dansylation (derivatization with dansyl chloride) and liquid chromatography-high resolution mass spectrometry (LC-HRMS) was developed for the quantitative analysis of phenolic compounds (phenols) in environmental samples. A magnetic-HLB (hydrophilic lipophilic balanced) material was synthesized and applied as an adsorbent in magnetic solid-phase extraction (MSPE) for the enrichment of the analytical targets. Furthermore, with the solid-phase isotope labeling, the desalting and removal of labeling residuals could be simplified over conventional in-solution labeling. In addition to overcoming the matrix effect by isotope dansylation, the sensitivity for the analysis of phenols by LC-HRMS was remarkably improved by over 100-fold. The method was systematically verified, and good accuracy (86.5-104.9%) and precision (<8.6% and <11.4% for intra- and inter-day, respectively) were achieved for the tested 15 phenols. The limits of detection (LODs) of this method were estimated to be 0.2-5 ng L-1 and 5-100 ng kg-1 in estuary water and sediment samples, respectively. With this method, samples collected from the Daliao River estuary (Panjin, China) were analyzed. It was found that all of the targeted phenols were detected at concentrations ranging from unquantifiable to 485 ng L-1 (the total concentration of analytes found in each sample were in the range 822-957 ng L-1) and unquantifiable to 1368 ng kg-1 (the total concentration of analytes found in each sample were in the range 2251-2992 ng kg-1) in water and sediment, respectively.

Performance and microbial community analysis of bioaugmented activated sludge for nitrogen-containing organic pollutants removal.

Nitrogen-containing organic pollutants (quinoline, pyridine and indole) are widely distributed in coking wastewater, and bioaugmentation with specific microorganisms may enhance the removal of these recalcitrant pollutants. The bioaugmented system (group B) was constructed through inoculation of two aromatics-degrading bacteria, Comamonas sp. Z1 (quinoline degrader) and Acinetobacter sp. JW (indole degrader), into the activated sludge for treatment of quinoline, indole and pyridine, and the non-bioaugmented activated sludge was used as the control (group C). Both groups maintained high efficiencies (> 94%) for removal of nitrogen-containing organic pollutants and chemical oxygen demand (COD) during the long-term operation, and group B was highly effective at the starting period and the operation stage fed with raw wastewater. High-throughput sequencing analysis indicated that nitrogen-containing organic pollutants could shape the microbial community structure, and communities of bioaugmented group B were clearly separated from those of non-bioaugmented group C as observed in non-metric multidimensional scaling (NMDS) plot. Although the inoculants did not remain their dominance in group B, bioaugmentation could induce the formation of effective microbial community, and the indigenous microbes might play the key role in removal of nitrogen-containing organic pollutants, including Dokdonella, Comamonas and Pseudoxanthomonas. Phylogenetic Investigation of Communities by Reconstruction of Unobserved States (PICRUSt) analysis suggested that bioaugmentation could facilitate the enrichment of functional genes related to xenobiotics biodegradation and metabolism, probably leading to the improved performance in group B. This study indicated that bioaugmentation could promote the removal of nitrogen-containing organic pollutants, which should be an effective strategy for wastewater treatment.