Development of Flexible Biceps Tremors Sensing Chip of PVDF Fibers with Nano-Silver Particles by Near-Field Electrospinning.

Polyvinylidene fluoride (PVDF) and AgNO3/PVDF composite piezoelectric fibers were prepared using near-field electrospinning technology. The prepared fibers are attached to the electrode sheet and encapsulated with polydimethylsiloxane to create an energy acquisition device and further fabricated into a dynamic sensing element. The addition of AgNO3 significantly increased the conductivity of the solution from 40.33 µS/cm to 883.59 µS/cm, which in turn made the fiber drawing condition smoother with the increase of high voltage electric field and reduced the fiber wire diameter size from 0.37 µm to 0.23 µm. The tapping test shows that the voltage signal can reach ~0.9 V at a frequency of 7 Hz, and the energy conversion efficiency is twice that of the PVDF output voltage. The addition of AgNO3 effectively enhances the molecular bonding ability, which effectively increases the piezoelectric constants of PVDF piezoelectric fibers. When the human body is exercised for a long period of time and the body is overloaded, the biceps muscle is found to produce 8 to 16 tremors/second through five arm flexion movements. The voltage output of the flexible dynamic soft sensor is between 0.7-0.9 V and shows an orderly alternating current waveform of voltage signals. The sensor can be used to detect muscle tremors after high-intensity training and to obtain advance information about changes in the symptoms of fasciculation, allowing for more accurate diagnosis and treatment.

Characterization of Piezoelectric Properties of Ag-NPs Doped PVDF Nanocomposite Fibres Membrane Prepared by Near Field Electrospinning.

BACKGROUND: In this study, Near-field electrospinning (NFES) technique is used with a cylindrical collector to fabricate a large area permanent piezoelectric micro and nanofibers by a prepared solution. NFES requires a small electric field to fabricate fibers Objective: The objective of this paper to investigate silver nanoparticle (Ag-NP)/ Polyvinylidene fluoride (PVDF) composite as the best piezoelectric material with improved properties to produced tremendously flexible and sensitive piezoelectric material with pertinent conductance Methods: In this paper, we used controllable electrospinning technique based on Near-field electrospinning (NFES). The process parameter for Ag-NP/PVDF composite electrospun fiber based on pure PVDF fiber. A PVDF solution concentration of 18 wt.% and 6 wt.% silver nitrate, which is relative to the weight of PVDF wt.% with 1058 µS conductivity fibers, have been directly written on a rotating cylindrical collector for aligned fiber PVDF/Ag-NP fibers are patterned on fabricated copper (Cu) interdigitated electrodes were implemented on a thin flexible polyethylene terephthalate (PET) substrate and Polydimethylsiloxane (PDMS) used as a package to enhance the durability of the PVDF/ Ag-NP device. RESULTS: A notable effect on the piezoelectric response has been observed after Ag-NP addition, confirmed by XRD characterization and tapping test of Ag-NP/PVDF composite fiber. The morphology of the PVDF/Ag-NP fibers and measure diameter by scanning electron microscopy (SEM) and Optical micrograph (OM), of fiber. Finally, a diameter of PVDF/Ag-NP fibers up to ~7 µm. The high diffraction peak at 2θ = 20.5˚ was investigated by X-ray diffraction (XRD) in the piezoelectric crystal ß-phase structure. Further addition of silver nanoparticles (Ag- NPs) in the PVDF solution resulted in enhancing the electromechanical conversion of the fibers from ~0.1 V to ~1 V. CONCLUSION: In conclusion, we can say that confirmed and validated the addition of Ag-NP in PVDF could enhance the piezoelectric property by using NFES technique with improved crystalline phase content can be useful for a wide range of power and sensing applications like biomedical devices and energy harvesting, among others.

Flexible Piezoresistive Tactile Sensor Based on Polymeric Nanocomposites with Grid-Type Microstructure.

Piezoresistive tactile sensors made using nanocomposite polymeric materials have been shown to possess good flexibility, electrical performance, and sensitivity. However, the sensing performance, especially in the low-pressure range, can be significantly improved by enabling uniform dispersion of the filler material and utilization of effective structural designs that improve the tactile sensing performance. In this study, a novel flexible piezoresistive tactile sensor with a grid-type microstructure was fabricated using polymer composites comprising multi-walled carbon nanotubes (MWCNTs) as the conductive filler and polydimethylsiloxane (PDMS) as the polymeric matrix. The research focused on improving the tactile sensor performance by enabling uniform dispersion of filler material and optimizing sensor design and structure. The doping weight ratio of MWCNTs in PDMS varied from 1 wt.% to 10 wt.% using the same grid structure-sensing layer (line width, line spacing, and thickness of 1 mm). The sensor with a 7 wt.% doping ratio had the most stable performance, with an observed sensitivity of 6.821 kPa-1 in the lower pressure range of 10-20 kPa and 0.029 kPa-1 in the saturation range of 30-200 kPa. Furthermore, the dimensions of the grid structure were optimized and the relationship between grid structure, sensitivity, and sensing range was correlated. The equation between pressure and resistance output was derived to validate the principle of piezoresistance. For the grid structure, dimensions with line width, line spacing, and thickness of 1, 1, and 0.5 mm were shown to have the most stable and improved response. The observed sensitivity was 0.2704 kPa-1 in the lower pressure range of 50-130 kPa and 0.0968 kPa-1 in the saturation range of 140-200 kPa. The piezoresistive response, which was mainly related to the quantum tunneling effect, can be optimized based on the dopant concentration and the grid microstructure. Furthermore, the tactile sensor showed a repeatable response, and the accuracy was not affected by temperature changes in the range of 10 to 40 °C and humidity variations from 50 to 80%. The maximum error fluctuation was about 5.6% with a response delay time of about 1.6 ms when cyclic loading tests were performed under a normal force of 1 N for 10,200 cycles. Consequently, the proposed tactile sensor shows practical feasibility for a wide range of wearable technologies and robotic applications such as touch detection and grasping.

Enhancement of PVDF Sensing Characteristics by Retooling the Near-Field Direct-Write Electrospinning System.

This research aimed to develop a direct-write near-field electrospinning system (DW-NFES) with three-axis positioning of controllable speed, torque and position to produce sizable and high-quality piezoelectric fibers for sensing purposes. Sensor devices with high electrical response signals were developed and tested. To achieve DW-NFES purpose, a servo motor controller was designed to develop a high response rate, accurate positioning, and stable mobile device through the calculation of bandwidth and system time delay. With this retooled system of DW-NFES, controllable and uniform size fibers in terms of diameters, stretching force, and interspaces can be obtained. Sensor devices can be made selectively without a complicated lithography process. The characteristics of this DW-NFES platform were featured by high response rate, accurate positioning, and stable movement to make fibers with high piezoelectric property. In this study, polyvinylidene fluoride (PVDF) was used to explore and enhance their sensing quality through the platform. The parametric study of the process factors on piezoelectric sensing signals mainly included the concentration of electrospinning PVDF solution, high voltage electric field, and collection speed. Finally, the surface morphology and piezoelectric properties of the as-electrospun PVDF fibers were examined by scanning electron microscopy (SEM) and characterized by electrical response measurement techniques. The results showed that the fiber spinning speed of the DW-NFES system could be increased to ~125 from ~20 mm/s and the accuracy precision was improved to ~1 from ~50 µm, compared to conventional step motor system. The fiber diameter reached ~10 µm, and the electrospinning pitch reached to as small as ~10 µm. The piezoelectric output voltage of the electrospun fibers was increased ~28.6% from ~97.2 to ~125 mV; the current was increased ~27.6% from ~163 to ~208 nA, suggesting that the piezoelectric signals can be enhanced significantly by using this retooled system. Finally, an external control module (Arduino-MAGE) was introduced to control the PVDF piezoelectric fiber sensors integrated as a sensing array. The behavior of long-term sedentary patients can be successfully detected by this module system to prevent the patients from the bedsores.

Polyvinylidene Fluoride-Added Ceramic Powder Composite Near-Field Electrospinned Piezoelectric Fiber-Based Low-Frequency Dynamic Sensors.

In this study, near-field electrospinning (NFES) is used to fabricate Ba x Sr1-x TiO3 (BST)/poly(vinylidene fluoride) (PVDF) piezoelectric fiber composites with excellent mechanical properties and chemical properties. BST ceramic powder is blended with PVDF solution uniformly to prepare a solution of appropriate conductance. The parameter for BST/PVDF fiber processing is based on PVDF fibers. Scanning electron microscopy, differential scanning calorimetry, microtensile testing, Fourier transform infrared spectroscopy, and electricity test of the blends of BST/PVDF fibers are incorporated. Mechanical properties of the fibers are then measured by microtensile testing. Effects of distinct ratios of Ba/Sr and the content of Ba0.7Sr0.3TiO3 ceramic powder on BST/PVDF piezoelectric fibers are discussed. Finally, BST/PVDF piezoelectric fiber composites are patterned on a poly(ethylene terephthalate) (PET)-based structure with an interdigital electrode as a BST/PVDF flexible energy harvester to capture ambient energy. The results show that the BST ceramic powder is ∼58-93 nm, and the diameters of piezoelectric fiber composites are ∼6.8-13.7 µm. The tensile strength of piezoelectric fiber composites is ∼74.92 MPa, and the Young's coefficient tensile strength is ∼3.74 GPa. Mechanical properties are 2-3 times higher than those of pure PVDF piezoelectric fibers. The maximum open-circuit voltage and closed-loop current of BST/PVDF fibers reached ∼1025 mV and ∼391 nA, respectively. The electromechanical energy conversion efficiency of the BST/PVDF energy harvester is found to be 1-2 times higher than that of the PVDF energy harvester. It is confirmed and validated that the addition of BST ceramic powder could effectively increase the piezoelectric constant of PVDF piezoelectric fibers.

Improvement of Model Predictive Current Control Sensing Strategy for a Developed Small Flux-Switching Permanent Magnet Motor.

This paper presents an improved control system for a small flux-switching permanent magnet motor (FSPM) to enhance its performance and torque sensing. The analytical magnetic circuit design was used to determine the related motor parameters, such as the air gap flux density, permeance coefficient (Pc), torque, winding turns, pole number, width, length, magnet geometry, and the current density of FSPM. The electromagnetic analysis of this motor was performed by software (ANSYS Maxwell) to optimize the motor performance. In this study, the performance of FSPM was investigated by the uniform design experimentation (UDE). For the control system, the model predictive current control (MPCC) is currently recognized as a high-performance control strategy, due to its quick response and simple principle. This model contained the nonlinear part of the system, to improve the torque ripple of FSPM. A modified MPCC strategy was proposed to improve the distortion of the current waveform and decrease the computational burden. The new modified control architecture was mainly composed of three parts, such as the estimation of electromotive force (EMF), current prediction, and optimal vector selection/vector duration. When the reference voltage vector was obtained, the three-phase duties were easily determined by the principle of space vector modulation (SVM). The results show the different strategy methods between the newly proposed modified MPCC and traditional proportional integral (PI) controller. In the control of FSPM, a modified MPCC strategy was able to achieve a better performance response and decrease the computational burden. At a low speed of 350 rpm, the proposed modified MPCC can achieve a better dynamic response. The nonlinear problem of the startup speed was also effectively resolved. The torque sensing performance of the simulation and the experimental test value were compared. The torque sensing performance of the simulation and the actual test value were also examined. In this study, the optimization focused not only on the motor design and fabrication, but also on an improved motor control strategy and torque sensing, in order to achieve the integrity of the FSPM system.

Fabrication of Biodegradable Poly(caprolactone) Spherical-Microcarriers for Arterial Embolization.

This study aimed to develop emulsification assisted with ultrasonic atomization (EUA) to make embolic biodegradable poly(caprolactone) (PCL) spherical-microcarriers with uniform particle size for mass production which was used to cure hepatocellular carcinoma, because this kind of embolic drugs is expensive at the current market due to their complex manufacturing process. The embolic spherical-microcarriers with sustained-releasing therapeutic agents can shrink an unresectable tumor into a respectable size. Through high frequency vibrating surface on the ultrasonic atomizer nozzle, the thin liquid film for PCL oil-phase solution was broken into the uniform PCL microdroplets (particle sizes are from 20 to 55 µm) with less medicine loss. To determine the optimal parameters to make PCL microcarriers, the ultrasonic module parameters including the concentration of PCL solution, vibrating amplitude of atomizer, feeding rate of PCL oil-phase solution and collection distance on the particle size of microdroplets were analyzed. Besides, a vertical circulation flow field of aqueous-phase poly(vinyl alcohol) (PVA) solution was created to enhance the separation of the microdroplets and increase the production of the PCL microcarriers, and about 8~11 wt% of PVA solution with high stable dispersion property was used to effectively improve the yield rate of PCL spherical-microcarriers (89.8~98.2 wt%). The final particle size of PCL microcarriers was ca. 5-18 µm, indicating an about 25-50% volume shrinkage from microdroplets to solid spherical-microcarriers.

A Misalignment Optical Guiding Module for Power Generation Enhancement of Fixed-Type Photovoltaic Systems.

: This study presents a misalignment light-guiding module to increase the effectiveness of absorbing light. For a general fixed-type photovoltaic (PV) panel, the misalignment light decreases the efficiency of the system. A solar tracking system was installed for obtaining higher power generation. However, the cost of the PV system and maintenance was 5-10 times higher than the general type. In this study, this module is composed of an array of misalignment light-guiding units that consist of a non-axisymmetric compound parabolic curve (NACPC) and a freeform surface collimator. The NACPC efficiently collects the misalignment light within ±30° and guides the light to the collimator. The light has a better uniformity and smaller angle at the exit aperture. The simulation results show that the optical efficiency of the unit was above 70% when the misalignment angle was smaller than 20°. The experimental results show that the power generation of the light-guiding unit was 1.8 times higher than the naked PV panel.

Nanoparticles-mediated Brain Imaging and Disease Prognosis by Conventional as well as Modern Modal Imaging Techniques: a Comparison.

BACKGROUND: Multimodal imaging plays an important role in the diagnosis of brain disorders. Neurological disorders need to be diagnosed at an early stage for their effective treatment as later, it is very difficult to treat them. If possible, diagnosing at an early stage can be much helpful in curing the disease with less harm to the body. There is a need for advanced and multimodal imaging techniques for the same. This paper provides an overview of conventional as well as modern imaging techniques for brain diseases, specifically for tumor imaging. In this paper, different imaging modalities are discussed for tumor detection in the brain along with their advantages and disadvantages. Conjugation of two and more than two modalities provides more accurate information rather than a single modality. They can monitor and differentiate the cellular processes of normal and diseased condition with more clarity. The advent of molecular imaging, including reporter gene imaging, has opened the door of more advanced noninvasive detection of brain tumors. Due to specific optical properties, semiconducting polymer-based nanoparticles also play a pivotal role in imaging tumors. OBJECTIVE: The objective of this paper is to review nanoparticles-mediated brain imaging and disease prognosis by conventional as well as modern modal imaging techniques. CONCLUSION: We reviewed in detail various medical imaging techniques. This paper covers recent developments in detail and elaborates a possible research aspect for the readers in the field.

Vein Pattern Locating Technology for Cannulation: A Review of the Low-Cost Vein Finder Prototypes Utilizing near Infrared (NIR) Light to Improve Peripheral Subcutaneous Vein Selection for Phlebotomy.

One of the most common means for diagnosis is through medical laboratory testing, which primarily uses venous blood as a sample. This requires an invasive method by cannulation that needs proper vein selection. The use of a vein finder would help the phlebotomist to easily locate the vein, preventing possible pre-analytical error in the specimen collection and even more discomfort and pain to the patient. This paper is a review of the scientific publications on the different developed low-cost vein finder prototypes utilizing camera assisted near infrared (NIR) light technology. Methods: Electronic databases were searched online, these included PubMed (PMC), MEDLINE, Science Direct, ResearchGate, and Institute of Electrical and Electronics Engineers (IEEE) Xplore digital library. Specifically, publications with the terms vein finder prototype, NIR technology, vein detection, and infrared imaging were screened. In addition, reference lists were used to further review related publications. Results: Cannulation challenges medical practitioners because of the different factors that can be reduced by the utilization of a vein finder. A limited number of publications regarding the assessment of personnel performing cannulation were observed. Moreover, variations in methodology, number of patients, type of patients according to their demographics and materials used in the assessment of the developed prototypes were noted. Some studies were limited with regard to the actual human testing of the prototype. Conclusions: The development of a low-cost effective near infrared (NIR) vein finder remains in the phase of improvement. Since, it is being challenged by different human factors, increasing the number of parameters and participants/human for actual testing of the prototypes must also be taken into consideration for possible commercialization. Finally, it was noted that publications regarding the assessment of the performance of phlebotomists using vein finders were limited.

Study on Delamination Between Polymer Materials and Metals in IC Packaging Process.

The electronic package interconnects electronic signals from one area to another and package delamination is a serious problem in the configuration of materials. This study focused on decreasing the delamination of the low-profile fine pitch ball grid array (LFBGA) and plastic ball grid array (PBGA) packages in terms of polymer thermal issue, metal bonding and bonding mechanisms. PBGA and LFBGA are a very common type of packaging processes in the electronics industry. The present study dealt first with delamination of the LFBGA packaging, through characterization and determination of physical and chemical properties such as surface roughness, surface energy, and contact angle. The relationship between surface roughness and delamination was verified through various roughness bonding experiments. In addition, the surface energy was determined by measuring the contact angle after cleaning the metal surface of Cu, Ni and Cr with Ar + O2 gas, and, this gas plasma treatment was applied to enhance the adhesive properties. The compositions of the surface were analyzed through an X-ray photoelectron spectroscopy (XPS). Also, the delamination issue between the corner of the heat sink cap and the epoxy resin was observed for delamination of the LFBGA packaging. Further, this study analyzed the PBGA packaging process through the finite element analysis simulation software ANSYS. To improve the heat sink cap delamination issue of the PBGA, a new chamfer design of the corner seat was streamlined to decrease the stress value and delamination. Besides, the simulation results demonstrated that the stress value reduced after increasing the shoulder length. The results implicate that the stress value is inversely proportional to the shoulder width and the chamfer radius. This study demonstrated that the optimization in design was able reduce the delamination phenomena in configuration material.

Cancer Biology Aspects of Computational Methods & Applications in Drug Discovery.

BACKGROUND: Cancer is one of the most debilitating diseases worldwide; even though advances in molecular and cellular biology have contributed to the decline of mortality associated with cancer, the procedure of drug discovery and development of cancer are time-consuming and expensive. However, with computer-aided drug discovery (CADD) techniques, pharmaceutical firms can save production costs and reduce the time of introducing effective anticancer drugs for clinical trials. CADD strategies like structure-based drug designing, ligandbased drug designing, and combined structure-based and ligand-based approaches also have the advantage of identifying target sites and discovering active compounds with high affinity for the target sites. In this article, research carried out on cancer biology aspect of the computational approaches in drug discovery technology have been reviewed. OBJECTIVE: The main objective of the study is to identify the potential causes and the development of the cancer. In addition to this, its recovery has been discussed briefly. CONCLUSION: Our findings indicate that only a few studies have been carried out regarding this area. Hence, it is recommended that further researches should be conducted on the computational methods for identifying candidate drugs for breast, pancreatic, colon, prostate, and other types of cancer.

Energy Harvester and Cell Proliferation from Biocompatible PMLG Nanofibers Prepared Using Near-Field Electrospinning and Electrospray Technology.

This paper describes the application of piezoelectric fibers and films formed using near-field electrospinning (NFES) and electrospray (ESP) technology. Poly(γ-methyl L-glutamate) (PMLG), a biocompatible material, was mixed with poly(ethylene oxide) (PEO) and surfactant to obtain a solution of appropriate viscosity and conductance. Because the orientation of the dipoles in PMLG was enhanced upon applying an electric field, we could use the NFES and ESP processes to align dipoles and enhance the piezoelectric properties of the resulting fibrous materials. The maximum peak voltage of a fiber-based harvester prepared using this approach was 0.056 V. Because the fibers and films were non-toxic biological materials displaying excellent piezoelectric characteristics, we deposited them on glass substrates coated with indium tin oxide to observe their effects on the proliferation of cells. The negative charge of PMLG decreased the proliferation of mouse fibroblast cells (NIH3T3); indeed, decreasing the interspacing between the fibers slightly decreased the proliferation of these cells. Moreover, the migration of the cells was inhibited significantly, or even halted, when the coverage of the ESP films increased, implying a growth inhibition effect.