Evaluation of particle and volatile organic compound emissions during the use of 3D pens.

This study investigated particle and volatile organic compound (VOC) emission rates (ER) from 3D pens, which are increasingly popular in children's toys. Nine filaments and two 3D pens were evaluated using a flow tunnel, a scanning mobility particle sizer, a proton-transfer-reaction time-of-flight mass spectrometer for particles, and a thermal desorption-gas chromatography-mass spectrometer for VOCs. Results showed that the ERs varied with the pen type, filament, and brand. The particle ER was highest for acrylonitrile butadiene styrene (ABS), followed by polylactic acid (PLA) and polycaprolactone (PCL). Notably, ERs of 83 % and 33 % of ABS and PLA filaments exceeded the maximum allowable particle ER (MAER; 5 × 109 particles/min) for 3D printers but were lower than the VOC MAER (173 µg/min in the office). Different filaments emitted diverse VOCs; ABS emitted styrene and benzene, PLA emitted lactide, and PCL emitted phenol. While particle ERs from 3D pens were comparable to those from printers, the total VOC ERs from 3D pens were slightly lower. Caution is warranted when using 3D pens because of potential health risks, especially their prolonged use, proximity to the breathing zone, and usage by children. This study highlights the need for considering particles and VOCs when assessing the safety of 3D pens, emphasizing awareness of potential hazards, particularly in child-oriented settings.

Effect of spraying air freshener on particulate and volatile organic compounds in vehicles.

People in these days spend approximately 6 % of their time in a means of transport. Air fresheners are frequently used in vehicles to mask odors; however, they can cause adverse health effects such as cardiovascular disease, systemic inflammation and autonomic dysfunction. This study aimed to identify the effects of air fresheners on the concentrations of particulate and volatile organic compounds (VOCs) in different vehicle cabins. Scanning mobility and optical particle sizers were used for the particle measurements. VOCs (e.g., BTEX and d-limonene) were collected using a Tenax TA. The products were sprayed for less than a minute. The study assessed three spray products (all trigger types), vehicle size (small, medium, and large), cabin temperature (10 °C, 20 °C, and 25 °C), and in-vehicle ventilation mode (all-off, recirculation, and external inflow modes). The particle concentration increased rapidly during the 1-min spraying of the products. The proportion of nanoparticles in the front seat (67.2 % ± 2.2 %) was 11.1 % ± 2.2 % lower than that in the rear seat (75.6 % ± 2.1 %). The spray product and vehicle size did not significantly affect the particle or VOC concentrations. With an increase in the temperature of the front seat, the proportion of nanoparticles increased by 25.3 % ± 3.2 %. Moreover, the maximum total VOC concentrations (front seat: 364.3 µg/m3; back seat: 241.3 µg/m3) were observed at 20 °C. Under in-vehicle ventilation, recirculation effectively reduced the overall particle concentration within the cabin; however, the generated VOCs circulated. The external inflow proved effective in cabin air purification by reducing the total VOC concentration to 56.0-57.2 % compared with other ventilation modes. These findings provide substantial insight into the persistence of particles and the dynamics of their dispersion, thereby enabling informed decision-making for particle-related risk management.

Non-target screening of volatile organic compounds in spray-type consumer products and their potential health risks.

Widespread use of spray-type consumer products can raise significant concerns regarding their effects on indoor air quality and human health. In this study, we conducted non-target screening using gas chromatography-mass spectrometry (GC-MS) to analyze VOCs in 48 different spray-type consumer products. Using this approach, we tentatively identified a total of 254 VOCs from the spray-type products. Notably, more VOCs were detected in propellant-type products which are mostly solvent-based than in trigger-type ones which are mostly water-based. The VOCs identified encompass various chemical classes including alkanes, cycloalkanes, monoterpenoids, carboxylic acid derivatives, and carbonyl compounds, some of which arouse concerns due to their potential health effects. Alkanes and cycloalkanes are frequently detected in propellant-type products, whereas perfumed monoterpenoids are ubiquitous across all product categories. Among the identified VOCs, 12 compounds were classified into high-risk groups according to detection frequency and signal-to-noise (S/N) ratio, and their concentrations were confirmed using reference standards. Among the identified VOCs, D-limonene was the most frequently detected compound (freq. 21/48), with the highest concentration of 1.80 mg/g. The risk assessment was performed to evaluate the potential health risks associated with exposure to these VOCs. The non-carcinogenic and carcinogenic risks associated with the assessed VOC compounds were relatively low. However, it is important not to overlook the risk faced by occupational exposure to these VOCs, and the risk from simultaneous exposure to various VOCs contained in the products. This study serves as a valuable resource for the identification of unknown compounds in the consumer products, facilitating the evaluation of potential health risks to consumers.

Comparison of sampling methods for the determination of volatile organic compounds in consumer aerosol sprays.

Many studies have evaluated the hazardous substances contained in various household chemical products. However, for aerosol spray products there is currently no international standard sampling method for use in a component analysis. The aim of this study was to develop an appropriate sampling method for the analysis of volatile organic compounds (VOCs) in consumer aerosol sprays. Two different sampling methods, spraying (into a vial) and perforating (and transferring the contents into a vial), were used to evaluate the levels of 16 VOC components in eight different aerosol spray products. All eight products contained trace amounts of hazardous VOCs, and a quantitative analysis showed that, for the same product, VOC concentrations were higher when spraying than when perforating. Using the spraying method, average toluene, ethylbenzene, p-xylene, o-xylene, and styrene concentrations were 1.80-, 2.10- 2.25-, 2.03-fold, and 1.28-fold higher, respectively, than when using the perforating method. The spraying method may provide more realistic estimates of the user's exposure to harmful substances and the associated health risks when using spray products. Of the two representative methods widely used to analyze harmful substances in consumer aerosol sprays, the spraying method is recommended over the perforating method for the analysis of VOCs.

Measurement of Airborne Particles and Volatile Organic Compounds Produced During the Heat Treatment Process in Manufacturing Welding Materials.

Background: There is little information about the airborne hazardous agents released during the heat treatment when manufacturing a welding material. This study aimed to evaluate the airborne hazardous agents generated at welding material manufacturing sites through area sampling. Methods: concentration of airborne particles was measured using a scanning mobility particle sizer and optical particle sizer. Total suspended particles (TSP) and respirable dust samples were collected on polyvinyl chloride filters and weighed to measure the mass concentrations. Volatile organic compounds and heavy metals were analyzed using a gas chromatography mass spectrometer and inductively coupled plasma mass spectrometer, respectively. Results: The average mass concentration of TSP was 683.1 ± 677.4 µg/m3, with respirable dust accounting for 38.6% of the TSP. The average concentration of the airborne particles less than 10 µm in diameter was 11.2-22.8 × 104 particles/cm3, and the average number of the particles with a diameter of 10-100 nm was approximately 78-86% of the total measured particles (<10 µm). In the case of volatile organic compounds, the heat treatment process concentration was significantly higher (p < 0.05) during combustion than during cooling. The airborne heavy metal concentrations differed depending on the materials used for heat treatment. The content of heavy metals in the airborne particles was approximately 32.6%. Conclusions: Nanoparticle exposure increased as the number of particles in the air around the heat treatment process increases, and the ratio of heavy metals in dust generated after the heat treatment process is high, which may adversely affect workers' health.

Occupational Exposure during Intraperitoneal Pressurized Aerosol Chemotherapy Using Doxorubicin in a Pig Model.

Background: This study evaluated occupational exposure levels of doxorubicin in healthcare workers performing rotational intraperitoneal pressurized aerosol chemotherapy (PIPAC) procedures. Methods: All samples were collected during PIPAC procedures applying doxorubicin to an experimental animal model (pigs). All procedures were applied to seven pigs, each for approximately 44 min. Surface samples (n = 51) were obtained from substances contaminating the PIPAC devices, surrounding objects, and protective equipment. Airborne samples were also collected around the operating table (n = 39). All samples were analyzed using ultra-high performance liquid chromatography-mass spectrometry. Results: Among the surface samples, doxorubicin was detected in only five samples (9.8%) that were directly exposed to antineoplastic drug aerosols in the abdominal cavity originating from PIPAC devices. The telescopes showed concentrations of 0.48-5.44 ng/cm2 and the trocar showed 0.98 ng/cm2 in the region where the spraying nozzles were inserted. The syringe line connector showed a maximum concentration of 181.07 ng/cm2, following a leakage. Contamination was not detected on the surgeons' gloves or shoes. Objects surrounding the operating table, including tables, operating lights, entrance doors, and trocar holders, were found to be uncontaminated. All air samples collected at locations where healthcare workers performed procedures were found to be uncontaminated. Conclusions: Most air and surface samples were uncontaminated or showed very low doxorubicin concentrations during PIPAC procedures. However, there remains a potential for leakage, in which case dermal exposure may occur. Safety protocols related to leakage accidents, selection of appropriate protective equipment, and the use of disposable devices are necessary to prevent occupational exposure.

Occupational Exposure to Refractory Ceramic Fibers in the Semiconductor Scrubber Manufacturing Industry.

Background: Refractory ceramic fibers (RCFs) are a suspected carcinogen but have been widely used as insulations. Depending on the temperature, RCFs can transform into crystalline SiO2, which is a carcinogen that can be present in the air during bulk RCF handling. This study analyzed the physicochemical and morphological characteristics of RCFs at high temperatures and determined the exposure levels during the semiconductor scrubber maintenance. Methods: Sampling was conducted at a company that manufactures semiconductor scrubbers using RCFs as insulation. Bulk RCF samples were collected both before and after exposure to a scrubber temperature of 700°C. Airborne RCFs were collected during scrubber maintenance, and their characteristics were analyzed using microscopes. Results: The components of bulk RCFs were SiO2 and Al2O3, having an amorphous structure. Airborne RCFs were morphologically different from bulk RCFs in size, which could negatively affect maintenance workers' health. 58% of airborne RCFs correspond to the size of thoracic and respirable fibers. RCFs did not crystallize at high temperatures. The exposure caused by airborne RCFs during the scrubber frame assembly and insulation replacement was higher than the occupational exposure limit. Conclusion: Workers conducting insulation replacement are likely exposed to airborne RCFs above safe exposure limits. As RCFs are suspected carcinogens, this exposure should be minimized through prevention and precautionary procedures.

Characteristics of COVID-19 infection clusters occurring among workers in several Asia-Pacific countries.

The types of workplaces and occupations with coronavirus 2019 (COVID-19) clusters vary between countries and periods. We aimed to characterize major occupational groups with mass outbreaks of COVID-19 infections in several Asia-Pacific countries. Data on the major occupations or workplaces reporting COVID-19 cases in workplaces from January 2020 to July 2021 was collected from industrial hygiene professionals in nine countries. The proportion of workers accounted for 39.1 to 56.6% of the population in each country. The number of workers covered in the national statistics varies among nations based on their definition of a worker. None of the countries examined here have systematically collected occupational data on COVID-19 illnesses and deaths classified by type of industry, occupation, or job. Most countries experienced COVID-19 clusters among health and social care workers (HSCW) in hospitals or long-term care facilities. The types of occupations or workplaces with virus clusters in some participating countries included prisons, call centers, workplaces employing immigrants, garment facilities, grocery stores, and the military, which differed among countries, except for a few common occupations such as HSCW and those populated by immigrants. Further study is necessary in order to seek ways to control infection risks, including revisions to industrial-health-related laws.

Evaluation of airborne total suspended particulates and heavy metals in anodizing and electroplating surface treatment process.

This study is to evaluate exposure to harmful substances, such as particulate and heavy metals, by considering various factors, in anodizing and electroplating surface treatment process. Exposure evaluation studies on seven heavy metals (Cr, Zn, Ni, Pb, Cd, Al, and Ba) and total suspended particulates (TSP) were conducted. Heavy metals were analyzed using inductively coupled plasma mass spectrometry (ICP-MS). This study also checked the ventilation volume of the hood with a thermal anemometer. Measurement was conducted for 8 h and 8 days. The sample number, N, of the heavy metals and TSP was 107. Geometric mean (GM) of TSP during Cr plating process was 6.15(GSD, 3.35) mg/m3. GM of Cr during Cr plating was 1.86(GSD, 6.65) mg/m3. GM of TSP and heavy metals differences were statistically significant for each process and date variation. Average ventilation volume for all hoods ranged from 1.20 to 4.98 m3/s. In the hood 30 cm from bath, ventilation was 0.1 times lower. Increasing ventilation volume of the hood was the most influential factor, followed by machine operation time and workload. The high concentration was due to low ventilation suction flow. We can improve health to reduce exposure by resolving the fundamental cause of risk occurrence.

Overview of Legal Measures for Managing Workplace COVID-19 Infection Risk in Several Asia-Pacific Countries.

BACKGROUND: Despite the lack of official COVID-19 statistics, various workplaces and occupations have been at the center of COVID-19 outbreaks. We aimed to compare legal measures and governance established for managing COVID-19 infection risks at workplaces in nine Asia and Pacific countries and to recommend key administrative measures. METHODS: We collected information on legal measures and governance from both general citizens and workers regarding infection risks such as COVID-19 from industrial hygiene professionals in nine countries (Indonesia, India, Japan, Malaysia, New Zealand, Republic of the Philippines, Republic of Korea, Taiwan, and Thailand) using a structured questionnaire. RESULTS: A governmental body overseeing public health and welfare was in charge of containing the spread and occurrence of infectious diseases under an infectious disease control and prevention act or another special act, although the name of the pertinent organizations and legislation vary among countries. Unlike in the case of other traditional hazards, there have been no specific articles or clauses describing the means of mitigating virus risk in the workplace that are legally required of employers, making it difficult to define the responsibilities of the employer. Each country maintains own legal systems regarding access to the duration, administration, and financing of paid sick leave. Many workers may not have access to paid sick leave even if it is legally guaranteed. CONCLUSION: Specific legal measures to manage infectious disease risks, such as providing proper personal protective equipment, education, engineering control measures, and paid sick leave are recommended to be stipulated in Industrial safety and health-related acts.

Estimates of particulate matter inhalation doses during three-dimensional printing: How many particles can penetrate into our body?

Harmful emissions including particulates, volatile organic compounds, and aldehydes are generated during three-dimensional (3D) printing. Ultrafine particles are particularly important due to their ability to penetrate deep into the lung. We modeled inhalation exposure by particle size during 3D printing. A total of six thermoplastic filaments were used for printing under manufacturer's recommended conditions, and particle emissions in the size range between 10 nm and 10 µm were measured. The inhalation exposure dose including inhaled and deposited doses was estimated using a mathematical model. For all materials, the number of particles between 10 nm and 1 µm accounted for a large proportion among the released particles, with nano-sized particles being the dominant size. More than 1.3 × 109 nano-sized particles/kgbw/g (95.3 ± 104.0 ng/kgbw/g) could be inhaled, and a considerable amount was deposited in respiratory regions. The total deposited dose in terms of particle number was 3.1 × 108 particles/kgbw/g (63.6% of the total inhaled dose), and most (41.3%) were deposited in the alveolar region. The total mass of particles deposited was 19.8 ± 16.6 ng/kgbw/g, with 10.1% of the total mass deposited in the alveolar region. Given our findings, the inhalation exposure level is mainly determined by printing conditions, particularly the filament type and manufacturer-recommended extruder temperature.

Chemical Use and Associated Health Concerns in the Semiconductor Manufacturing Industry.

BACKGROUND: Research on the status of many chemicals used in the semiconductor industry is needed. The purpose of this study was to describe the overall status of chemical use in the semiconductor industry in Korea and to examine it from a health perspective. METHODS: Data on the status of chemical use and safety data sheets at 11 of 12 major semiconductor workplaces in Korea were collected. The number of chemical products and chemical constituents, quantities of chemicals, and trade secret ingredients used, as well as the health hazards were examined. RESULTS: On average, 210 chemical products and 135 chemical constituents were used at the surveyed workplaces. Among all chemical products, 33% (range: 16-56%) contained at least one trade secret ingredient. Most of the trade secret ingredients were used in the photolithography process. Several carcinogens, including sulfuric acid, chromic acid, ethylene oxide, crystalline silica, potassium dichromate, and formaldehyde were also used. Only 29% (39 of 135) of the chemical constituents had occupational exposure limits, and more than 60% had no National Fire Protection Association health, safety, and reactivity ratings. Based on the aforementioned results, this study revealed the following. First, many chemical products and constituents are being used in the semiconductor industry and many products contained trade secret ingredients. Second, many products contained significant amounts of carcinogenic, mutagenic, and reproductive toxicant materials. CONCLUSION: We conclude that protecting workers in the semiconductor industry against harm from chemical substances will be difficult, due to widespread use of trade secret ingredients and a lack of hazard information. The findings of the status of chemical use and the health and safety risks in semiconductor industry will contribute to epidemiological studies, safe workplace, and worker health protection.

Exposure assessment of elemental carbon, polycyclic aromatic hydrocarbons and crystalline silica at the underground excavation sites for top-down construction buildings.

Enclosed underground excavation worksite has an environment with poor ventilation and exposure to hazardous substances from diesel engine exhaust and construction materials. The objective of this study was to evaluate the exposure level of elemental carbon (EC), organic carbon (OC), total carbon (TC), polycyclic aromatic hydrocarbons (PAHs), dust and crystalline silica (CS) during underground excavation work for top down construction buildings. Active local air sampling for EC, OC, and TC (n = 105), PAHs (n = 50), dust (n = 34) and CS (n = 34) was conducted from inside and outside the excavator at underground excavation workshop in four different construction sites. EC, OC, TC and CS were sampled with each respirable and total particulates. EC, OC, and TC were collected on quartz-filter and analyzed using the thermal optical transmittance method. PAHs was collected on polytetrafluorethylene filter with XAD-2 and analyzed using liquid chromatography with fluorescence detector. CS and particulates were collected on poly vinyl chloride filter and analyzed using fourier-transform infrared spectroscopy. The geometric mean of respirable EC, OC, TC, total PAHs, respirable dust and respirable CS were 8.69 µg/m3, 34.32 µg/m3, 44.96 µg/m3, 6.818 µg/m3 0.13 mg/m3 and 0.02 mg/m3 from inside the excavator and 33.20 µg/m3, 46.53 µg/m3, 78.21 µg/m3, 3.934 µg/m3, 0.9 mg/m3 and 0.08 mg/m3 from outside the excavator (underground excavation workshop), respectively. The EC and RCS concentration from outside the excavator is significantly higher than that of inside the excavator (p<0.01). The worksite with rock ground, higher vehicle density, blasting and enclosed environments had higher exposure to EC than other sites (p<0.05). There was no significant difference of EC concentration between total and respirable particulates. In top down construction sites, EC concentrations during underground excavation work exceeded recommended exposure limits as 20 µg/m3, accounted for about 50% of the total sample, and the level of concentration of RCS exceeded 1.5 times of occupational exposure limit, 0.05 mg/m3. Efforts are needed to minimize exposure to diesel engine exhaust and silica in underground excavation sites. Management of diesel engine vehicle, supply of fresh air and ventilation and introducing water facilities to create wet environment in underground worksites are strongly suggested.

Behavioral characteristics to airborne particles generated from commercial spray products.

Commercial spray products are commonly used in daily life and airborne particles generated by these products may cause adverse health effects. Our study was aimed to characterize the behaviors of airborne particles from spray products and to determine the deposition loss rate. Four categories of spray products with highly frequent use - air fresheners, fabric deodorants, window cleaners, and a bathroom cleaner - were selected for the study. The products were applied in a cleanroom according to the instructions for use. Airborne particles (10-10,000 nm) were measured within the breathing zone of a user with a scanning mobility particle sizer and an optical particle spectrometer. Additionally, filter sampling was performed to examine the morphological characteristics of the particles using a field emission-scanning electron microscope (FE-SEM). The initial concentration and particle size distribution varied among different spray types and products. Two propellant-type air fresheners that we tested showed a high initial concentration of smaller sized particles. However, one of these and all hand-pressure type propellants showed a low initial concentration in all size ranges. We observed that particles in nucleation mode (10-31.6 nm) decreased and aggregated particles shifted to accumulation mode (100-1,000 nm) over time. The FS-SEM analysis confirmed the aggregation of nano-sized particles for all products. The deposition loss rates of various particle sizes depended on the initial concentration and distribution of particle sizes. For two air fresheners with high initial concentrations, the loss rate of small-sized particles was higher than that of the other products whereas the particle loss rate of large-sized particles was higher, regardless of initial concentration. The results of this study can give us useful information in the behaviors of airborne particles in the consumer spray products and resulting exposure assessment especially in the application to the exposure modeling of spray products.

Evaluation of Short-Term Exposure Levels on Ammonia and Hydrogen Sulfide During Manure-Handling Processes at Livestock Farms.

BACKGROUND: Ammonia and hydrogen sulfide are harmful gases generated during aerobic/anaerobic bacterial decomposition of livestock manure. We evaluated ammonia and hydrogen sulfide concentrations generated from workplaces at livestock farms and determined environmental factors influencing the gas concentrations. METHODS: Five commercial swine farms and five poultry farms were selected for monitoring. Real-time monitors were used to measure the ammonia and hydrogen sulfide concentrations and environmental conditions during the manure-handling processes. Monitoring was conducted in the manure storage facility and composting facility. Information on the farm conditions was also collected through interview and walk-through survey. RESULTS: The ammonia concentrations were significantly higher at the swine composting facilities (9.5-43.2 ppm) than at other manure-handling facilities at the swine and poultry farms, and high concentrations of hydrogen sulfide were identified during the manure agitation and mixing process at the swine manure storage facilities (6.9-19.5 ppm). At the poultry manure-handling facilities, the ammonia concentration was higher during the manure-handling processes (2.6-57.9 ppm), and very low hydrogen sulfide concentrations (0-3.4 ppm) were detected. The air temperature and relative humidity, volume of the facility, duration of manure storage, and the number of animals influenced the gas concentrations. CONCLUSION: A high level of hazardous gases was generated during manure handling, and some levels increased up to risk levels that can threaten workers' health and safety. Some of the farm operational factors were also found to influence the gas levels. By controlling and improving these factors, it would be possible to protect workers' safety and health from occupational risks.

Physicochemical characteristics of colloidal nanomaterial suspensions and aerosolized particulates from nano-enabled consumer spray products.

Physicochemical properties between colloidal engineered nanomaterials (ENMs) and aerosols released from consumer spray products were characterized. A dynamic light scattering (DLS), transmission electron microscopy (TEM), and inductively coupled plasma mass spectrometer (ICP-MS) were used to evaluate the suspended ENMs in the products. Direct-reading instruments, TEM, and ICP-MS were used to characterize the properties of aerosolized ENMs. The aerosolized organic compounds with ENMs were assumed to be vaporized for a short time after spraying. The median diameter of ENMs in product solutions measured by DLS was about 200-350 nm, while individual particle was confirmed from 3 to 50 nm by TEM. The size of aerosolized ENMs was ranged from 7 to 44 nm, and their aggregates were about 100-1000 nm in near distance. Some inorganic substances including raw nanomaterials were also found in the aerosol. The particles released from the propellant sprays were identified in far distance, while they were not found in far distance when pump sprays were used. The number concentration from the propellant sprays increased up to 6000 particles/cm3 /g at near distance and dispersed to far distance, while the most of droplets emitted from pump sprays were settled down near sprayer's location. We found other metals besides labeled ENMs are included in each product and the characteristics of the particles are different when they are sprayed.

Behavioral characteristics of polyhexamethyleneguanidine (PHMG) particles in aqueous solution and air when sprayed into an ultrasonic humidifier.

Polyhexamethyleneguanidine (PHMG) is widely used as a disinfectant to prevent microbial contamination in ultrasonic humidifiers in Korea; however, sales have been prohibited by the government after an outbreak of severe lung injury among humidifier disinfectant users. This study was therefore conducted to determine the characteristics of PHMG particles in aqueous solution and to investigate the behavior of airborne particles generated when using PHMG as a humidifier disinfectant. Three types of PHMG were selected (manufactured in Korea, USA, and China), with dynamic light scattering (DLS) used to determine their behavioral characteristics in aqueous solution. To determine the airborne behavioral characteristics, PHMG was diluted to obtain high (62.5-65 ppm) and low (6.25-6.5 ppm) concentrations, and then real-time monitoring instruments were used to measure the effect of using a diffusion dryer and thermodenuder to control moisture in a cleanroom. A polycarbonate filter sample was analyzed by field emission-scanning electron microscope-energy dispersive spectrometry (FE-SEM-EDS) to determine the particle morphology. The DLS intensity results for the three products showed a slightly right-shifted (~100 nm) bimodal distribution relative to the airborne particle size distribution. The size of the airborne PHMG particles increased during the spraying due to aggregation, with the particle size of aggregated particles confirmed by FE-SEM to be approximately 20 nm or more. As the PHMG concentration increased by 10 times, the airborne concentrations measured by the real-time monitoring instrument increased by 2-3 times for nanoparticles, and by 45-85 times for 1-10 µm particles during humidifier operation; however, 99% of the particles generated could be classified as PM1. Without ventilation, even after operating the humidifier, the PHMG particles could be airborne for about 2 h until the background concentration was reached. Therefore, we found that the airborne behavior was affected by PHMG concentration. Products from different manufacturers had no effect on the airborne behavior.

Effect of nozzle temperature on the emission rate of ultrafine particles during 3D printing.

Ultrafine particles and other hazardous materials are emitted during 3D printing, but the effect of temperature on such particles has not been studied systematically. The aim of this study was to evaluate the effect of temperature on the emission rate of particulate matter during fused deposition modeling (FDM) three-dimensional (3D) printing using different filament types. The number concentration of particles was measured with direct-reading instruments in an exposure chamber at various temperatures while using four filament materials during 3D printing. The temperature was increased from 185 to 290°C in 15°C increments, while incorporating the manufacturer-recommended operating conditions. The emission rate increased gradually as the temperature increased for all filament types, and temperature was the key factor affecting the emission rate after filament type. For all filaments, at the lowest operating temperature, the emission rate was 107 -109 particles/min, whereas the emission rate at the highest temperature was about 1011 particles/min, that is, 100-10 000 times higher than the emission rate at the lowest temperature. To reduce particle emissions from 3D printing, we recommend printing at the lowest temperature possible or using low-emission materials.

Evaluation of Hazardous Chemicals with Material Safety Data Sheet and By-products of a Photoresist Used in the Semiconductor-Manufacturing Industry.

BACKGROUND: The photolithography process in the semiconductor industry uses various chemicals with little information on their constitution. This study aimed to identify the chemical constituents of photoresist (PR) products and their by-products and to compare these constituents with material safety data sheets (MSDSs) and analytical results. METHODS: A total of 51 PRs with 48 MSDSs were collected. Analysis consisted of two parts: First, the constituents of the chemical products were identified and analyzed using MSDS data; second, for verification of the by-products of PR, volatile organic compounds were analyzed. The chemical constituents were categorized according to hazards. RESULTS: Forty-five of 48 products contained trade secrets in amounts ranging from 1 to 65%. A total of 238 ingredients with multiple counting (35 ingredients without multiple counting) were identified in the MSDS data, and 48.7% of ingredients were labeled as trade secrets under the Korea Occupational Safety and Health Act. The concordance rate between the MSDS data and the analytical result was 41.7%. The by-product analysis identified 129 chemicals classified according to Chemical Abstracts Service No., with 17 chemicals that are carcinogenic, mutagenic, and reprotoxic substances. Formaldehyde was found to be released from 12 of 21 products that use novolak resin. CONCLUSION: We confirmed that several PRs contain carcinogens, and some were not specified in the toxicological information in the MSDS. Hazardous chemicals, including benzene and formaldehyde, are released from PRs products as by-products. Therefore, it is necessary to establish a systematic management system for chemical compounds and the working environment.

Chemical use in the semiconductor manufacturing industry.

BACKGROUND: The semiconductor industry is known to use a number of chemicals, but little is known about the exact chemicals used due to the ingredients being kept as a trade secret. OBJECTIVES: The objective of this study was to analyze chemical use using a safety data sheet (SDS) and chemical inventory provided by a major semiconductor company, which operated two factories (A and B). METHODS: Descriptive statistics were obtained on the number of chemical products and ingredients, photoresists, and carcinogens, classified by the International Agency for Research on Cancer (IARC), as well as trade secret ingredients. The total chemical use per year was estimated from chemical inventories mass (kg). RESULTS: A total of 428 and 432 chemical products were used in factories A and B, respectively. The number of pure chemical ingredients, after removing both trade secret ingredients and multiple counting, was 189 and 157 in factories A and B, respectively. The number of products containing carcinogens, such as sulfuric acid, catechol, and naphthalene was 47/428 (A) and 28/432 (B). Chemicals used in photolithography were 21% (A) and 26% (B) of all chemical products, and more than 97% among them were chemicals containing trade secret ingredients. CONCLUSIONS: Each year, 4.3 and 8.3 tons of chemicals were used per person in factories A and B, respectively. Because of the high level of commercial secrecy and the use of many unregulated chemicals, more sustainable policies and methods should be implemented to address health and safety issues in the semiconductor industry.