Effects of hydroxyapatite on PMMA-HAp cement for biomedical applications.

OBJECTIVE: The main goal of this study was to examine the influence of hydroxyapatite (HAp) macroaggreate concentrations on thermal and mechanical properties of radioactive bone cement and to study the relation of glass transition Tg with its mechanical properties. METHODS: The bone cement as (1-x)PMMA-xHAp binary system was prepared in six [x] distinct concentration parameters of 0.0 up to 0.5. The HAp was synthesized using a solgel procedure following calcination by thermal treatment. The composite was prepared in cold based (non-radioactive) mixing polymethyl methacrylate (PMMA) and HAp. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and mechanical compressive strength (CS) were used to measure the thermal and mechanical properties. RESULTS: The DSC and TGA thermal profiles in function to concentration parameter [x] were presented. The CS lies in a range of 3.71-7.37 MPa and the glass transition temperature Tg = 126.27 °C. There was a direct relationship between the PMMA-HAp thermoplastic properties with mechanical and thermal properties in function of HAp concentrations. CONCLUSION: The specific PMMA-HAp composite, with a concentration ratio of 1:1 and HAp thermal treatment at the Tg, provides a material with a compression strength of 7.37 MPa and a suitable amount of porous similar to a trabecular bone, possible to apply in bone cement implants, regardless of whether they are radioactive or not.

Development and chemical characterization of biodegradable polymeric implants containing sirolimus for the treatment of malignant solid tumors.

The use of sirolimus and its analogs has been evaluated in studies aimed at combating several types of cancer; however, because of the limited bioavailability of the drug, the search for new forms of administration is required. Biodegradable polymeric implants containing sirolimus were developed and assessed as an alternative method of drug administration. Implants containing 25 % (w/w) sirolimus were prepared employing the polymer matrices chitosan, polycaprolactone and poly(lactic-co-glycolic acid) (PLGA) in two proportions: PLGA 50:50 and PLGA 75:25. Thermal analysis techniques such as thermogravimetry and differential scanning calorimetry, combined with x-ray diffraction were used to characterize and evaluate the compatibility of the constituents of the formulation. No incompatibilities were found between the components, but drug amorphization was observed in all samples. Implants made from the polymers chitosan and PCL may accelerate the degradation of SRL when these polymers are dissolved in methanol at 50 °C. HPLC analysis showed that the implant prepared with PLGA 75:25 did not present degradation products and maintained its appropriate drug content, even when dissolved in methanol and heated to 50 °C. Therefore, it represents the most suitable biodegradable polymer for use in implants developed for the treatment of malignant solid tumors. However, it is still necessary to further study the drug effects after amorphization of the crystal and also to perform stability and solubility analysis.

Polyurethane foam impregnated with lignin as a filler for the removal of crude oil from contaminated water.

The present study describes the influence of the concentration of lignin when used as a filler in polyurethane foam for crude oil sorption. The foams (lignin 0-20wt%) were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric analysis, contact angle and density. The FTIR analysis confirmed urethane linkage formation, showing that the chemical structure of the polymer was preserved, despite the addition of different lignin concentrations. Thermogravimetric analysis showed that the presence of lignin has altered the onset temperature (Tonset) of the foams, decreasing as the concentration of lignin is increased. The contact angle analysis showed a decrease in the hydrophobicity of the foams with increasing lignin concentration. All modified foams showed an improvement in the oil sorption capacity in a PUF/oil/water system, and the PUF-10 showed an improvement of about 35.5% compared to the PUF-blank. The Langmuir isotherm showed a better fit to the data and predicted a maximum oil adsorption of 28.9gg-1 by the PUF-10. The ΔG° value of -4.4kJmol-1 indicated that crude oil adsorption process by PUF-10 was spontaneous. The results of reuse of the PUF-10 showed that oil removal efficiency remained greater than 95% after five consecutive cycles.

Influence of the power density on the kinetics of photopolymerization and properties of dental composites.

Polymer shrinkage during photopolymerization of dimethacrylate monomers, used for many years to produce materials for dental restoration, can induce either the formation of tooth-restoration gaps or the production of residual stress depending on the quality of adhesion between tooth and dental composites. In this work, the effect of the power density, used to photopolymerize three commercial dental composites (Fill Magic, Supra Fill, and Z100), on the kinetics of the reaction was investigated to determine processing conditions in which the generation of residual stress would be reduced by allowing polymer chains and macromers to flow before freezing during gelation of the polymer network. The kinetics of photopolymerization of the dental composites was monitored by real-time infrared (FTIR) spectroscopy. Polymer shrinkage and mechanical properties were also investigated by using, respectively, density and microhardness measurements. Results showed that the final conversion (after 200 s), volumetric shrinkage, and microhardness values were not affected by different power densities, mainly because the amount of energy used during photopolymerization was set constant by using different irradiation times. Lower power densities were able to reduce the maximum polymerization rate and delay the formation of a rigid network. Conversion before the formation of the rigid network was also enhanced by using a lower power density. Considering that too premature gelation can lead to residual stress during shrinkage, the results of this work indicated that the use of a lower power density can be effective in terms of delaying the onset of the formation of a rigid network, providing then conditions for macromolecules to flow and relieve stress during shrinkage.