Amphiphilic Block Copolymer of Poly(dimethylsiloxane) and Methoxypolyethylene Glycols for High-Permeable Polysulfone Membrane Preparation.

Poly(dimethylsiloxane)-block-methoxypolyethylene glycols (PDMS-b-mPEG) were synthesized by Steglich esterification. The high-permeable membrane (PSf/PDMS-b-mPEG) was prepared by using PDMS-b-mPEG as additives. The successful synthesis of PDMS-b-mPEG was confirmed by nuclear magnetic resonance. Field emission scanning electron microscopy images show that the distribution of finger-like macroporous and sponge-like macroporous can be modulated by controlling the ratio of the hydrophilic/hydrophobic components of additives. The distribution of additives and membrane wettability are validated with X-ray photoelectron spectroscopy and water contact angle test. The permeability of the blended membrane, especially for the membrane PSf/PDMS-b-mPEG1900 (M3), was remarkably improved. The water permeability of M3 (239.4 L/m2·h·bar) was 6.6 times that of the unblended membrane M0 (42.5 L/m2·h·bar). The findings of protein BSA filtration show that the flux recovery ratio of M3 is 89.2% at a BSA retention rate of about 80%, which demonstrates that the polysulfone membranes blended with PDMS-b-mPEG have excellent antifouling performance and extraordinary permeability.

Top-Down Strategy of Implantable Biosensor Using Adaptable, Porous Hollow Fibrous Membrane.

Fabrication of an outer membrane is crucial for an implantable biosensor to enhance the long-term stability and accuracy of sensors. Herein, an adaptable, controllable, porous outer membrane for an implantable biosensor was fabricated using a "top-down" method, allowing maximum retention of enzyme activity and fine control over membrane microstructure. Polysulfone hollow fibrous membranes with different pore sizes and porosities were used as a base membrane. Chitosan (CH) and sodium alginate (SA) were self-assembled on the inner surface of PSfHM to construct a biocompatible and conductive interface between PSfHM and the electrode. In vitro and in vivo experiments were used to evaluate the performance of implantable glucose biosensors with PSfHM and CH/SA modified PSfHM (PSfHM-CH/SA). The glucose biosensor with PSfHM-CH/SA exhibited a more stable output current than bare sensors and a quick response time (<50 s). The glucose biosensor with PSfHM-CH/SA linear sensing range was between 0 and 22 mM ( R2 = 0.9905), and relative sensitivity remained at >87% within 7 days and >76% within 15 days. Furthermore, response currents recorded by implanted sensors closely followed the blood glucose trend from the tail vein blood during in vivo experiments.

Integration of RAFT polymerization and click chemistry to fabricate PAMPS modified macroporous polypropylene membrane for protein fouling mitigation.

A copper (I)-catalyzed azide-alkyne cycloaddition (CuAAC) grafting-to method was used to tether alkyne-terminated poly(2-acrylamido-2-methyl propane sulfonic acid) (alkyne-PAMPS) to the azide functionalized macroporous polypropylene membrane (MPPM-N3). Alkyne-PAMPS was synthesized by the reversible addition-fragmentation chain transfer polymerization (RAFT) of AMPS with an alkyne-terminated trithiocarbonate served as a chain transfer agent. The combination of RAFT polymerization with click chemistry to graft polymer to the surface of polypropylene membrane produced relatively high grafting density and controllable grafting chain length. The structure and composition of the modified and unmodified MPPM surfaces were analyzed by attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR), X-ray photoelectron spectroscopy (XPS); field emission scanning electron microscopy (FE-SEM) was employed to observe the morphological changes on the membrane surface. The permeation performances were tested by the filtration of protein dispersion. The experimental results show that with the grafting degree going up, the relative flux reduction decreases, while the relative flux recovery ratio increases, and the protein fouling is obviously mitigated by tethering PAMPS to the membrane surface. The modified membranes can be potentially applied for fouling reduction during the filtration of proteins.

Tramadol pretreatment enhances ketamine-induced antidepressant effects and increases mammalian target of rapamycin in rat hippocampus and prefrontal cortex.

Several lines of evidence have demonstrated that acute administration of ketamine elicits fast-acting antidepressant effects. Moreover, tramadol also has potential antidepressant effects. The aim of this study was to investigate the effects of pretreatment with tramadol on ketamine-induced antidepressant activity and was to determine the expression of mammalian target of rapamycin (mTOR) in rat hippocampus and prefrontal cortex. Rats were intraperitoneally administrated with ketamine at the dose of 10 mg/kg or saline 1 h before the second episode of the forced swimming test (FST). Tramadol or saline was intraperitoneally pretreated 30 min before the former administration of ketamine or saline. The locomotor activity and the immobility time of FST were both measured. After that, rats were sacrificed to determine the expression of mTOR in hippocampus and prefrontal cortex. Tramadol at the dose of 5 mg/kg administrated alone did not elicit the antidepressant effects. More importantly, pretreatment with tramadol enhanced the ketamine-induced antidepressant effects and upregulated the expression of mTOR in rat hippocampus and prefrontal cortex. Pretreatment with tramadol enhances the ketamine-induced antidepressant effects, which is associated with the increased expression of mTOR in rat hippocampus and prefrontal cortex.

Surface modification of polypropylene macroporous membrane to improve its antifouling characteristics in a submerged membrane-bioreactor: H(2)O plasma treatment.

To improve the antifouling characteristics of polypropylene hollow fiber macroporous membranes in a submerged membrane-bioreactor for wastewater treatment, the membranes were surface modified by H(2)O plasma treatment. Structural and morphological changes on the membrane surface were characterized by X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM). The change of surface wettability was monitored by contact angle measurement. The static water contact angle of the modified membrane reduced obviously with the increase of plasma treatment time. The total surface free energy and its dispersive component decreased, while the polar component increased with the increase of treatment time. The relative pure water flux for the modified membranes increased gradually with the increase of plasma treatment time. The tensile strength and the tensile elongation at break for the membranes decreased after plasma treatment. After continuous operation in a submerged membrane-bioreactor for about 68 h, flux recovery after water and caustic cleaning, flux ratio after fouling were improved by 2.0, 3.6 and 22.0%, while reduction of flux was reduced by 1.1% for the 1 min H(2)O plasma treated membrane, compared to those of the unmodified membrane.

Surface modification of polypropylene microporous membrane to improve its antifouling characteristics in an SMBR: N2 plasma treatment.

Fouling is the major obstacle in membrane processes applied in water and wastewater treatment. The polypropylene hollow fiber microporous membranes (PPHFMMs) were surface modified by N(2) low-temperature plasma treatment to improve the antifouling characteristics. Morphological changes on the membrane surface were characterized by field emission scanning electron microscopy (FE-SEM). The change of surface wettability was monitored by contact angle measurements. The static water contact angle of the modified membrane reduced obviously; the relative pure water flux of the modified membranes increased with the increase of plasma treatment time. To assess the relation between plasma treatment and membrane fouling in a submerged membrane bioreactor (SMBR), filtration of activated sludge was carried out by using synthetic wastewater. After continuous operation in the SMBR for about 90 h, flux recoveries for the N(2) plasma-treated PPHFMM for 8 min were 62.9% and 67.8% higher than those of the virgin membrane after water and NaOH cleaning. The irreversible fouling resistance decreased after plasma treatment.

Improvement of antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20.

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes (PPMMs). Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR) and field emission scanning electron microscope (FE-SEM) were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor (MBR), filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.

Enhancement of the flux for polypropylene hollow fiber membrane in a submerged membrane-bioreactor by surface modification.

To improve its limiting flux and antifouling characteristics in a submerged membrane-bioreactor (SMBR) for wastewater treatment, polypropylene hollow fiber microporous membrane (PPHFMM) was surface-modified by the plasma-induced immobilization of poly (N-vinyl-2-pyrrolidone) (PVP) and the plasma treatment with different gases respectively. Attenuated total reflection-Fourier transform infrared spectroscopy (FT-IR/ATR), X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscope (FE-SEM) were used to characterize the structural and morphological changes on the membrane surface. Water contact angle was measured by the sessile drop method. It was found that the water contact angle was 128.8, 72.3, 62.7, 74.4, 79.1, 86.3, and 71.3 degrees for the nascent, PVP-immobilized, air, O2, Ar, CO2 and H2O plasma treated PPHFMM, respectively. The SMBR was operated at fixed transmembrane pressure to determine the limiting flux for the PPHFMM before and after surface modification. Results showed that the limiting flux appeared to be 103, 159, 117, 133, 136, 121 and 152 L/(m(2)x h) for the nascent, PVP-immobilized, air, 02, Ar, CO2 and H2O plasma treated PPHFMM, respectively. After continuous operation for about 50 h in the SMBR, the antifouling characteristics were improved to some extent.

[Chemical modification on the surface of nano-particles of ZnO and its characterization].

After nano-particles (ZnO) had been encapsulated by a kind of water-soluble cellulose Hydoxyl-Propyl-Methyl Cellulose (HPMC), then methyl methacrylate was grafted onto the surface of them. Thus the surface of nano-ZnO had been successfully modified. FTIR, DTA and TEM were utilized to confirm the results. FTIR shows that HPMC was adsorbed onto the surface of ZnO, and PMMA was also grafted onto its surface, DTA says that the heat stability of HPMC, HPMC-g-PMMA and ZnO/HPMC-g-PMMA increased greatly, TEM photo demonstrates that polymer adhered onto the surface of nano-ZnO which was encapsulated by a layer of film-like polymer.