Complex network analysis of slaughterhouse waste anaerobic digestion: From failure to success of long-term operation.

The study explored slaughterhouse waste (SHW) as prime feedstock associated with and without supplement of an external slowly degradable lignocellulosic carbon source to overcome the synergistic co-inhibitions of ammonia and fatty acids. Long-term solid-state digestion (SSD) and liquid-state digestion (LSD) were investigated using a mixture of pork liver and fat. At 2.0 g volatile solids (VS) L-1 d-1 of organic loading rate (OLR), the two reactors of SSD experienced operational instability due to ammonia inhibition and volatile fatty acid (VFA) accumulation while LSD successfully produced 0.725 CH4 L CH4 g-1VS during 197 d of working days under unfavorable condition with high total ammonia nitrogen (>4.7 g/L) and VFAs concentration (>1.9 g/L). The network analysis between complex microflora and operational parameters provided an insight for sustainable biogas production using SHW. Among all, hydrogenotrophic methanogens have shown better resistance than acetoclastic methanogens.

Responses of Coagulant Type, Dosage and Process Conditions to Phosphate Removal Efficiency from Anaerobic Sludge.

Phosphorus, a crucial component of life, may cause eutrophication if it is discharged untreated into the aquatic ecosystem. Phosphate (PO43-) may exist at an elevated level in anaerobic digestion (AD) effluents and can lead to the clogging of pipes by forming struvite crystals. This study was conducted to assess the responses of coagulant type, dosage and process conditions to phosphate removal efficiency from anaerobic sludge. The experiments were performed in two steps. First, a sensitivity test was conducted to compare five coagulant types (alum, poly-aluminum chloride (PAC), FeCl2, FeCl3 and PAC + FeCl3) at standard coagulation conditions. The results showed that PAC would be the best coagulant among the tested, while a combination of PAC and FeCl3 may be beneficial under circumstances. Second, an optimization study was performed for PAC using response surface methodology employing central composite design. Among the three independent variables (coagulant dosage, slow mixing duration and agitation speed), the dosage was the sole significant variable for phosphate removal efficiency, while the other two had limited effects. A future study to optimize the rapid mixing conditions would give additional insights into the process. The results of this study may be useful to design a process to counteract phosphate discharges from AD plants, as well as to reduce the risks of pipe clogging and maintenance problems due to crystalline struvite formation in the later stage of AD.

Tracking microbial community shifts during recovery process in overloaded anaerobic digesters under biological and non-biological supplementation strategies.

Anaerobic digestion encounters operational instability due to fluctuations in organic loading. Propionic acid (HPr) is frequently accumulated due to its unfavorable reaction thermodynamics. Here, 'specific' bioaugmentation using HPr enrichment cultures (three different injection regimes of quantity and frequency) was compared with 'non-specific' bioaugmentation using anaerobic sludge, and with non-biological supplementation of magnetite or coenzyme M. The specific bioaugmentation treatments showed superior recovery responses during continuous feeding after a peak overload. A 'one-shot' bioaugmentation with enrichment showed the best remediation, with ~25% recovery time and >10% CH4 conversion efficiency compared to the control. Consecutive bioaugmentation showed evidence of increased stability of the introduced community. Families Synergistaceae, Syntrophobacteraceae, and Kosmotogaceae were likely responsible for HPr-oxidation, in potential syntrophy with Methanoculleus and Methanobacterium. The different supplementation strategies can be considered to reduce the effect of start-up or overload in anaerobic digesters based on the availability of supplementation resources.

Density profile modeling for real-time estimation of liquid level in anaerobic digester using multiple pressure meters.

The liquid level of a bioreactor is an important operating parameter governing the hydraulic retention time. In this study, a novel method is proposed to estimate the liquid level of anaerobic digesters. The proposed method has an advantage over typical differential pressure measurement as it considers the heterogeneity of the digestate along the level using multiple pressure meters. The real-time measurement generates a model to fit the densities at different liquid columns, predicts the density of the surface layer and determines the overall liquid level. A pilot-scale (0.33 m3 working volume; 1.2 m liquid level) digester, equipped with seven pressure meters, was operated to test the methodology. The performance of the digester was confirmed stable during a long-term (175 d) operation. A set of density-pressure models was developed and were validated using the long-term experimental data. The new method employing cubic model showed significantly better estimation of the reactor level (mean error rate of 1.31%) with improved CDF, as compared with the traditional differential pressure method (mean error rate of 5.71%). The methodology proposed in this study is simple, robust, and cost-effective and can be used to provide additional insights into the operation of an anaerobic digester such as assessing the mixing efficiency.

Direct-patterning of porphyrin dot arrays and lines using electrohydrodynamic jet printing.

In this research, we have fabricated micron-sized patterns of porphyrins on silicon substrates using an electrohydrodynamic (EHD) jet printing technique. Optical and fluorescence microscopies have been used to examine the shape and fluorescence property of porphyrin patterns. The morphology of the porphyrin patterns printed with variously formulated porphyrin inks and the effects of applied voltage, working distance, and substrate properties on the morphology of patterns were investigated using scanning electron microscopy (SEM) and atomic force microscopy (AFM). We have also demonstrated the acid-vapor sensing capability of the porphyrins by exposing the porphyrin patterns on Si substrates to nitric acid vapor.