ABSTRACT
Elevated sea surface temperatures are causing an increase in coral bleaching events worldwide, and represent an existential threat to coral reefs. Early studies of Mesophotic Coral Ecosystems (MCEs) highlighted their potential as thermal refuges for shallow-water coral species in the face of predicted 21st century warming. However, recent genetic evidence implies that limited ecological connectivity between shallow- and deep-water coral communities inhibits their effectiveness as refugia; instead MCEs host distinct endemic communities that are ecologically significant in and of themselves. In either scenario, understanding the response of MCEs to climate change is critical given their ecological significance and widespread global distribution. Such an understanding has so far eluded the community, however, because of the challenges associated with long-term field monitoring, the stochastic nature of climatic events that drive bleaching, and the paucity of deep-water observations. Here we document the first observed cold-water bleaching of a mesophotic coral reef at Clipperton Atoll, a remote Eastern Tropical Pacific (ETP) atoll with high coral cover and a well-developed MCE. The severe bleaching (>70 % partially or fully bleached coral cover at 32 m depth) was driven by an anomalously shallow thermocline, and highlights a significant and previously unreported challenge for MCEs. Prompted by these observations, we compiled published cold-water bleaching events for the ETP, and demonstrate that the timing of past cold-water bleaching events in the ETP coincides with decadal oscillations in mean zonal wind strength and thermocline depth. The latter observation suggests any future intensification of easterly winds in the Pacific could be a significant concern for its MCEs. Our observations, in combination with recent reports of warm-water bleaching of Red Sea and Indian Ocean MCEs, highlight that 21st century MCEs in the Eastern Pacific face a two-pronged challenge: warm-water bleaching from above, and cold-water bleaching from below.
ABSTRACT
Extreme weather events are increasing in frequency and magnitude. Consequently, it is important to understand their effects and remediation. Resilience reflects the ability of an ecosystem to absorb change, which is important for understanding ecological dynamics and trajectories. To describe the impact of a powerful storm on coral reef structural complexity, we used novel computational tools and detailed 3D reconstructions captured at three time points over three years. Our data-set Reefs4D of 21 co-registered image-based models enabled us to calculate the differences at seven sites over time and is released with the paper. We employed six geometrical metrics, two of which are new algorithms for calculating fractal dimension of reefs in full 3D. We conducted a multivariate analysis to reveal which sites were affected the most and their relative recovery. We also explored the changes in fractal dimension per size category using our cube-counting algorithm. Three metrics showed a significant difference between time points, i.e., decline and subsequent recovery in structural complexity. The multivariate analysis and the results per size category showed a similar trend. Coral reef resilience has been the subject of seminal studies in ecology. We add important information to the discussion by focusing on 3D structure through image-based modeling. The full picture shows resilience in structural complexity, suggesting that the reef has not gone through a catastrophic phase shift. Our novel analysis framework is widely transferable and useful for research, monitoring, and management.
Subject(s)
Anthozoa , Coral Reefs , Animals , Ecosystem , Climate Change , FractalsABSTRACT
Quantifying coral reef biodiversity is challenging for cryptofauna and organisms in early life stages. We demonstrate the utility of eDNA metabarcoding as a tool for comprehensively evaluating invertebrate communities on complex 3D structures for reef reformation, and the role these structures play in provisioning habitat for organisms. 3D design and printing were used to create 18 complex tiles, which were used to form artificial reef structures. eDNA was collected from scraping tile surfaces for organismal biomass and from seawater samples around the artificial reefs in the Gulf of Eilat/Aqaba, Red Sea. Metabarcoding targeted the mitochondrial COI gene with specific primers for marine biodiversity. We provide the first eDNA biodiversity baseline for the Gulf of Eilat/Aqaba, capturing extensive information on species abundance, richness, and diversity. Tile tops had higher phylogenetic diversity and richness, despite a higher abundance of organisms on tile bottoms, highlighting the detection of cryptic organisms with eDNA. We recommend eDNA metabarcoding for reef restoration initiatives, especially for complex marine structures, to improve success and evaluation of biodiversity.
Subject(s)
Coral Reefs , DNA, Environmental , Phylogeny , Biodiversity , Ecosystem , Environmental MonitoringABSTRACT
The rapid decline of vulnerable coral reefs has increased the necessity of exploring interdisciplinary methods for reef restoration. Examining how to upgrade these tools may uncover options to better support or increase biodiversity of coral reefs. As many of the issues facing reef restoration today deal with the scalability and effectiveness of restoration efforts, there is an urgency to invest in technology that can help reach ecosystem-scale. Here, we provide an overview on the evolution to current state of artificial reefs as a reef reformation tool and discuss a blueprint with which to guide the next generation of biomimetic artificial habitats for ecosystem support. Currently, existing artificial structures have difficulty replicating the 3D complexity of coral habitats and scaling them to larger areas can be problematic in terms of production and design. We introduce a novel customizable 3D interface for producing scalable, biomimetic artificial structures, utilizing real data collected from coral ecosystems. This interface employs 3D technologies, 3D imaging and 3D printing, to extract core reef characteristics, which can be translated and digitized into a 3D printed artificial reef. The advantages of 3D printing lie in providing customized tools by which to integrate the vital details of natural reefs, such as rugosity and complexity, into a sustainable manufacturing process. This methodology can offer economic solutions for developing both small and large-scale biomimetic structures for a variety of restoration situations, that closely resemble the coral reefs they intend to support.