ABSTRACT
A number of quinoidal molecules with symmetric end-capping groups, particularly dicyanomethylene units, have been synthesized for organic optoelectronic materials. In comparison, dissymmetric quinoidal molecules, characterized by end-capping with different groups, are less explored. In this paper, we present the unexpected formation of new formal quinoidal molecules, which are end-capped with both dicyanomethylene and triphenylphosphonium moieties. The structures of these dissymmetric quinoidal molecules were firmly verified by single crystal structural analyses. On the basis of the control experiments and DFT calculations, we proposed the reaction mechanism for the formation of these dissymmetric quinoidal molecules. The respective zwitterionic forms should make contributions to the ground state structures of these quinoidal molecules based on the analysis of their bond lengths and aromaticity and Mayer Bond Orbital (MBO) calculation. This agrees well with the fact that negative solvatochromism was observed for these quinoidal molecules. Although these new quinoidal molecules are non-emissive both in solutions and crystalline states, they become emissive with quantum yields up to 51.4% after elevating the solvent viscosity or dispersing them in a PMMA matrix. Interestingly, their emissions can also be switched on upon binding with certain proteins, in particular with human serum albumin.
ABSTRACT
Conjugated polymers promise inherently flexible and low-cost thermoelectrics for powering the Internet of Things from waste heat1,2. Their valuable applications, however, have been hitherto hindered by the low dimensionless figure of merit (ZT)3-6. Here we report high-ZT thermoelectric plastics, which were achieved by creating a polymeric multi-heterojunction with periodic dual-heterojunction features, where each period is composed of two polymers with a sub-ten-nanometre layered heterojunction structure and an interpenetrating bulk-heterojunction interface. This geometry produces significantly enhanced interfacial phonon-like scattering while maintaining efficient charge transport. We observed a significant suppression of thermal conductivity by over 60 per cent and an enhanced power factor when compared with individual polymers, resulting in a ZT of up to 1.28 at 368 kelvin. This polymeric thermoelectric performance surpasses that of commercial thermoelectric materials and existing flexible thermoelectric candidates. Importantly, we demonstrated the compatibility of the polymeric multi-heterojunction structure with solution coating techniques for satisfying the demand for large-area plastic thermoelectrics, which paves the way for polymeric multi-heterojunctions towards cost-effective wearable thermoelectric technologies.
ABSTRACT
The oxygen sensitivity of voltage-gated potassium (Kv) channels regulates cardiovascular physiology. Members of the Kv1 family interact with intracellular Kvß proteins, which exhibit aldo-keto reductase (AKR) activity and confer redox sensitivity to Kv channel gating. The Kvß proteins contribute to vasoregulation by controlling outward K+ currents in smooth muscle upon changes in tissue oxygen consumption and demand. Considering exercise as a primary physiological stimulus of heightened oxygen demand, the current study tested the role of Kvß proteins in exercise performance, exercise-induced adaptations in myocardial perfusion, and physiological cardiac growth. Our findings reveal that genetic ablation of Kvß2 proteins diminishes baseline exercise capacity in mice and attenuates the enhancement in exercise performance observed after long-term training. Moreover, we demonstrate that Kvß2 proteins are critical for exercise-mediated enhancement in myocardial perfusion during cardiac stress as well as adaptive changes in cardiac structure. Our results underscore the importance of Kvß proteins in metabolic vasoregulation, highlighting their role in modulating both exercise capacity and cardiovascular benefits associated with training. Furthermore, our study sheds light on a novel molecular target for enhancing exercise performance and improving the health benefits associated with exercise training in patients with limited capacity for physical activity.
ABSTRACT
Introduction: Aneurysmal subarachnoid hemorrhage (SAH) constitutes a life-threatening condition, and identifying the ruptured aneurysm is essential for further therapy. This study aimed to evaluate the diagnostic accuracy of hypo-attenuating berry sign (HBS) observed on computed tomography (CT) scan in distinguishing ruptured aneurysms. Methods: In this diagnostic accuracy study, patients who had SAH and underwent non-enhanced brain CT scan were recruited. The HBS was defined as a hypo-attenuating area with an identifiable border in the blood-filled hyper-dense subarachnoid space. The screening performance characteristics of HBS in identifying ruptured aneurysms were calculated considering the digital subtraction angiography (DSA) as the gold standard. Results: A total of 129 aneurysms in 131 patients were analyzed. The overall sensitivity and specificity of HBS in the diagnosis of aneurysms were determined to be 78.7% (95%CI: 73.1% - 83.4%) and 70.7% (95%CI: 54.3% - 83.4%), respectively. Notably, the sensitivity increased to 90.9% (95%CI: 84.3% - 95.0%) for aneurysms larger than 5mm. The level of inter-observer agreement for assessing the presence of HBS was found to be substantial (kappa=0.734). The diagnostic accuracy of HBS in individuals exhibited enhanced specificity, sensitivity, and reliability when evaluating patients with a solitary aneurysm or assessing ruptured aneurysms. The multivariate logistic regression analysis revealed a statistically significant relationship between aneurysm size and the presence of HBS (odds ratios of 1.667 (95%CI: 1.238 - 2.244; p < 0.001) and 1.696 (95%CI: 1.231 - 2.335; p = 0.001) for reader 1 and reader 2, respectively). Conclusions: The HBS can serve as a simple and easy-to-use indicator for identifying a ruptured aneurysm and estimating its size in SAH patients. â.
ABSTRACT
Nanoresolved doping of polymeric semiconductors can overcome scaling limitations to create highly integrated flexible electronics, but remains a fundamental challenge due to isotropic diffusion of the dopants. Here we report a general methodology for achieving nanoscale ion-implantation-like electrochemical doping of polymeric semiconductors. This approach involves confining counterion electromigration within a glassy electrolyte composed of room-temperature ionic liquids and high-glass-transition-temperature insulating polymers. By precisely adjusting the electrolyte glass transition temperature (Tg) and the operating temperature (T), we create a highly localized electric field distribution and achieve anisotropic ion migration that is nearly vertical to the nanotip electrodes. The confined doping produces an excellent resolution of 56 nm with a lateral-extended doping length down to as little as 9.3 nm. We reveal a universal exponential dependence of the doping resolution on the temperature difference (Tg - T) that can be used to depict the doping resolution for almost infinite polymeric semiconductors. Moreover, we demonstrate its implications in a range of polymer electronic devices, including a 200% performance-enhanced organic transistor and a lateral p-n diode with seamless junction widths of <100 nm. Combined with a further demonstration in the scalability of the nanoscale doping, this concept may open up new opportunities for polymer-based nanoelectronics.
ABSTRACT
Chiral nanographenes (NGs) have garnered significant interest as optoelectronic materials in recent years. While helically chiral NGs have been extensively studied, axially chiral NGs have only witnessed limited examples, with no prior reports of axially chiral nonbenzenoid NGs. Herein we report an axially chiral nonbenzenoid nanographene featuring six pentagons and four heptagons. This compound, denoted as 2, was efficiently synthesized via an efficient Pd-catalyzed aryl silane homocoupling reaction. The presence of two bulky 3,5-di-tert-butylphenyl groups around the axis connecting the two nonbenzenoid PAH (AHR) segments endows 2 with atropisomeric chirality and high racemization energy barrier, effectively preventing racemization of both R- and S-enantiomers at room temperature. Optically pure R-2 and S-2 were obtained by chiral HPLC separation, and they exhibit circular dichroism (CD) activity at wavelengths up to 660 nm, one of the longest wavelengths with CD responses reported for the chiral NGs. Interestingly, racemic 2 forms a homoconfiguration π-dimer in the crystal lattice, belonging to the I222 chiral space group. Consequently, this unique structure renders crystals of 2 with a second harmonic generation (SHG) response, distinguishing it from all the reported axially chiral benzenoid NGs. Moreover, R-2 and S-2 also exhibit SHG-CD properties.
ABSTRACT
Polymer semiconductors hold tremendous potential for applications in flexible devices, which is however hindered by the fact that they are usually processed by halogenated solvents rather than environmentally more friendly solvents. An effective strategy to boost the solubility of high-performance polymer semiconductors in nonhalogenated solvents such as tetrahydrofuran (THF) by appending hydroxyl groups in the side chains is herein presented. The results show that hydroxyl groups, which can be easily incorporated into the side chains, can significantly improve the solubility of typical p- and n-types as well as ambipolar polymer semiconductors in THF. Meanwhile, the thin films of these polymer semiconductors from the respective THF solutions show high charge mobilities. With THF as the processing and developing solvents these polymer semiconductors with hydroxyl groups in the side chains can be well photopatterned in the presence of the photo-crosslinker, and the charge mobilities of the patterned thin films are mostly maintained by comparing with those of the respective pristine thin films. Notably, THF is successfully utilized as the processing and developing solvent to achieve high-density photopatterning with ≈82 000 device arrays cm-2 for polymer semiconductors in which hydroxyl groups are appended in the side chains.
ABSTRACT
Objective: To explore the morphodynamics of the active-inactive cell monolayer interfaces by using the active liquid crystal model. Methods: A continuum mechanical model was established based on the active liquid crystal theory and the active-inactive cell monolayer interfaces were established by setting the activity difference of cell monolayers. The theoretical equations were solved numerically by the finite difference and the lattice Boltzmann method. Results: The active-inactive cell interfaces displayed three typical morphologies, namely, flat interface, wavy interface, and finger-like interface. On the flat interfaces, the cells were oriented perpendicular to the interface, the -1/2 topological defects were clustered in the interfaces, and the interfaces were negatively charged. On the wavy interfaces, cells showed no obvious preference for orientation at the interfaces and the interfaces were neutrally charged. On the finger-like interfaces, cells were tangentially oriented at the interfaces, the +1/2 topological defects were collected at the interfaces, driving the growth of the finger-like structures, and the interfaces were positively charged. Conclusion: The orientation of the cell alignment at the interface can significantly affect the morphologies of the active-inactive cell monolayer interfaces, which is closely associated with the dynamics of topological defects at the interfaces.
ABSTRACT
ConspectusIn recent decades, there has been rapid development in the field of polymer semiconductors, particularly those based on conjugated donor-acceptor (D-A) polymers exhibiting high charge mobilities. Furthermore, the application of polymer semiconductors has been successfully extended to a wide range of functional devices, including sensors, photodetectors, radio frequency identification (RFID) tags, electronic paper, skin electronics, and artificial synapses. Over the past few years, there has been a growing focus on stimuli-responsive polymer semiconductors, which have the potential to impart additional functionalities to conventional field-effect transistors, garnering increased attention within the research community. In this context, phototunable polymer semiconductors have received significant attention due to their ability to utilize light as an external stimulus, enabling remote control of device performance with high spatiotemporal resolution. Meanwhile, integration of field-effect transistors with polymer semiconductors can enable the realization of complex functions. To achieve this, precise and controllable patterning of polymer semiconductors becomes essential. In this Account, we discuss our research findings in the context of phototunable and photopatternable polymer semiconductors. These developments encompass the following key aspects: (i) polymer semiconductors, such as poly(diketopyrrolopyrrole-quaterthiophene) (PDPP4T), exhibit phototunability when blended with the photochromic compound hexaarylbiimidazole (HABI). The photo/thermal-responsive field-effect transistors (FETs) can be fabricated using blending thin films. Remarkably, these photo/thermal-responsive transistors can function as photonically programmable and thermally erasable nonvolatile memory devices. (ii) By incorporating photoswitchable groups like azo and spiropyran into the side chains of conjugated D-A polymers, we can create phototunable polymer semiconductors. The reversible isomerization of azo and spiropyran groups significantly influences the charge transport properties of these polymer semiconductors. Consequently, the performance of the resulting FETs can be reversibly tuned through UV/visible or near-infrared light (NIR) irradiation. Notably, the incorporation of two distinct azo groups into the side chains leads to polymer semiconductors with tristable semiconducting states, offering the ability to logically control device performance using light irradiation at three different wavelengths. (iii) Photopatterning of p-type, n-type, and ambipolar semiconductors featuring alkyl side chains can be achieved using a diazirine-based, four-armed photo-cross-linker (4CNN) with a loading concentration of no more than 3% (w/w). Furthermore, the semiconducting performances of FETs with patterned thin films were found to be satisfactorily uniform. Importantly, the cross-linked thin films are robust and show good resistance to organic solvents, which is useful for fabricating all-solution processable multilayer electronic devices. (iv) The introduction of azide groups into the side chains of conjugated polymers results in a single-component semiconducting photoresist. The presence of azide groups renders the side chains with photo-cross-linking ability, enabling the successful formation of uniform patterns, even as small as 5 µm, under UV light irradiation. Benefiting from the single component feature, field-effect transistors with individual patterned thin films display satisfactorily uniform performances. Moreover, this semiconducting photoresist has proven effective for efficiently photopatterning other polymer semiconductors, demonstrating its versatility.
ABSTRACT
In recent decades, polymer semiconductors, extensively employed as charge transport layers in devices like organic field-effect transistors (OFETs), have undergone thorough investigation due to their capacity for large-area solution processing, making them promising for mass production. Research efforts have been twofold: enhancing the charge mobilities of polymer semiconductors and augmenting their mechanical properties to meet the demands of flexible devices. Significant progress has been made in both realms, propelling the practical application of polymer semiconductors in flexible electronics. However, integrating excellent semiconducting and mechanical properties into a single polymer still remains a significant challenge. This review intends to introduce the design strategies and discuss the properties of high-charge mobility stretchable conjugated polymers. In addition, another key challenge faced in this cutting-edge field is maintaining stable semiconducting performance during long-term mechanical deformations. Therefore, this review also discusses the development of healable polymer semiconductors as a promising avenue to improve the lifetime of stretchable device. In conclusion, challenges and outline future research perspectives in this interdisciplinary field are highlighted.
ABSTRACT
The laminated transition metal disulfides (TMDs), which are well known as typical two-dimensional (2D) semiconductive materials, possess a unique layered structure, leading to their wide-spread applications in various fields, such as catalysis, energy storage, sensing, etc. In recent years, a lot of research work on TMDs based functional materials in the fields of electromagnetic wave absorption (EMA) has been carried out. Therefore, it is of great significance to elaborate the influence of TMDs on EMA in time to speed up the application. In this review, recent advances in the development of electromagnetic wave (EMW) absorbers based on TMDs, ranging from the VIB group to the VB group are summarized. Their compositions, microstructures, electronic properties, and synthesis methods are presented in detail. Particularly, the modulation of structure engineering from the aspects of heterostructures, defects, morphologies and phases are systematically summarized, focusing on optimizing impedance matching and increasing dielectric and magnetic losses in the EMA materials with tunable EMW absorption performance. Milestones as well as the challenges are also identified to guide the design of new TMDs based dielectric EMA materials with high performance.
ABSTRACT
Since light propagation in water bodies is subject to absorption and scattering effects, underwater images using only conventional intensity cameras will suffer from low brightness, blurred images, and loss of details. In this paper, a deep fusion network is applied to underwater polarization images; that is, the underwater polarization images are fused with intensity images using the deep learning method. To construct a training dataset, we establish an experimental setup to obtain underwater polarization images and perform appropriate transformations to expand the dataset. Next, an end-to-end learning framework based on unsupervised learning and guided by an attention mechanism is constructed for fusing polarization and light intensity images. The loss function and weight parameters are elaborated. The produced dataset is used to train the network under different loss weight parameters, and the fused images are evaluated based on different image evaluation metrics. The results show that the fused underwater images are more detailed. Compared with light intensity images, the information entropy and standard deviation of the proposed method increase by 24.48% and 139%. The image processing results are better than other fusion-based methods. In addition, the improved U-net network structure is used to extract features for image segmentation. The results show that the target segmentation based on the proposed method is feasible under turbid water. The proposed method does not require manual adjustment of weight parameters, has faster operation speed, and has strong robustness and self-adaptability, which is important for research in vision fields, such as ocean detection and underwater target recognition.
Subject(s)
Algorithms , Unsupervised Machine Learning , Benchmarking , Entropy , WaterABSTRACT
Non-benzenoid polycyclic aromatic hydrocarbons (PAHs) have received a lot of attention because of their unique optical, electronic, and magnetic properties, but their synthesis remains challenging. Herein, we report a non-benzenoid isomer of peri-tetracene, diazulenorubicene (DAR), with two sets of 5/7/5 membered rings synthesized by a (3+2) annulation reaction. Compared with the precursor containing only 5/7 membered rings, the newly formed five membered rings switch the aromaticity of the original heptagon/pentagon from antiaromatic/aromatic to non-aromatic/antiaromatic respectively, modify the intermolecular packing modes, and lower the LUMO levels. Notably, compound 2 b (DAR-TMS) shows p-type semiconducting properties with a hole mobility up to 1.27â cm2 â V-1 s-1 . Moreover, further extension to larger non-benzenoid PAHs with 19â rings was achieved through on-surface chemistry from the DAR derivative with one alkynyl group.
ABSTRACT
The thermoelectric (TE) performance of organic materials is limited by the coupling of Seebeck coefficient and electrical conductivity. Herein a new strategy is reported to boost the Seebeck coefficient of conjugated polymer without significantly reducing the electrical conductivity by incorporation of an ionic additive DPPNMe3 Br. The doped polymer PDPP-EDOT thin film exhibits high electrical conductivity up to 1377 ± 109 S cm-1 but low Seebeck coefficient below 30 µV K-1 and a maximum power factor of 59 ± 10 µW m-1 K-2 . Interestingly, incorporation of small amount (at a molar ratio of 1:30) of DPPNMe3 Br into PDPP-EDOT results in the significant enhancement of Seebeck coefficient along with the slight decrease of electrical conductivity after doping. Consequently, the power factor (PF) is boosted to 571 ± 38 µW m-1 K-2 and ZT reaches 0.28 ± 0.02 at 130 °C, which is among the highest for the reported organic TE materials. Based on the theoretical calculation, it is assumed that the enhancement of TE performance for the doped PDPP-EDOT by DPPNMe3 Br is mainly attributed to the increase of energetic disorder for PDPP-EDOT.
ABSTRACT
Bacteriophages have been used in phage therapy for the treatment of bacterial infections. They are biological agents that used for management of diseases caused by resistant bacteria. As compared to antibiotics, phages can kill bacteria specifically. It requires more awareness about phage-host interactions by exploring new phages. Escherichia coli (E. coli) is a conditional pathogen and cause infections like pneumonia and diarrhea in hospitalized patients. In the current research work, a virus IME178, a novel strain, was extracted from the sewage of hospital against the clinical E. coli of multidrug resistant nature. Genomic characterization and transmission electron microscopy have exhibited relation of phage to the Tequintavirus genus, Demerecviridae family. The Phage IME178's double-stranded DNA genome was 108588 bp long, with a GC content of 39%. The phage genome transcribes 155 open reading frames, 72 are hypothetical proteins, 81 have putative functions assigned to them, and two are unknown to any database. A total number of 19 tRNA genes were found in the genome of this phage. There were no genes associated with virulence or drug resistance in the phage genome. According to a comparative genomic analysis, the genomic sequence of phage IME178 is 91% identical to E. coli phage phiLLS (NC 047822.1). The phage's host range and one-step growth curve were also estimated. As per genomic and bioinformatics analysis findings, Phage IME178, a propitious biological agent that infects E. coli and have the potential to use in phage therapies.
Subject(s)
Bacteriophages , Siphoviridae , Humans , Bacteriophages/genetics , Escherichia coli/genetics , Genome, Viral , GenomicsABSTRACT
Molecular probes which can be modulated, functionalized and used to visualize the processes are highly desirable for understanding and manipulating biological systems. Geometric cis and trans isomers of tetraphenylethene (TPE) emerge as attractive candidates to fulfill these tasks thanks to the unique aggregation-induced emission properties, tailorable structures, and responsiveness to external stimuli. This minireview focuses on cis and trans isomers of TPE derivatives that are functionalized with molecular recognition units for fluorescence detection, bioimaging and cancer therapy. The effects of molecular geometry on fluorescence property, target binding ability and biological activity are summarized. The feasibility to inâ vitro and inâ vivo switch molecular configuration and thus bio-activity is discussed. Finally, the future development and challenges are discussed in view of TPE-based stereoisomers for targeted sensing and imaging-guided modulation of biological processes.
Subject(s)
Fluorescent Dyes , Spectrometry, Fluorescence/methods , Isomerism , Fluorescent Dyes/chemistryABSTRACT
Non-benzenoid acenes containing heptagons have received increasing attention. We herein report a heptacene analogue containing a quinoidal benzodi[7]annulene core. Derivatives of this new non-benzenoid acene were obtained through an efficient synthetic strategy involving an Aldol condensation and a Diels-Alder reaction as key steps. The configuration of this heptacene analogue can be modulated from a wavy to a curved one by just varying the substituents from a (triisopropylsilyl)ethynyl group to a 2,4,6-triisopropylphenyl (Trip) group. When mesityl (Mes) groups are linked to the heptagons, the resulting non-benzenoid acene displays polymorphism with a tunable configuration from a curved to a wavy one upon varying the crystallization conditions. In addition, this new non-benzenoid acene can be oxidized or reduced by NOSbF6 or KC8 to the respective radical cation or radical anion. Compared with the neutral acene, the radical anion shows a wavy configuration and the central hexagon becomes aromatic.
ABSTRACT
Emissive organic semiconductors are highly demanding for organic light-emitting transistors (OLETs) and electrically pumped organic lasers (EPOLs). However, it remains a great challenge to obtain organic semiconductors with high carrier mobility and high photoluminescence quantum yield simultaneously. Here, a new design strategy is reported for highly emissive ambipolar and even n-type semiconductors by introducing perfluorophenyl groups into polycyclic aromatic hydrocarbons such as perylene and anthracene. The results reveal that 3,9-diperfluorophenyl perylene (5FDPP) exhibits the ambipolar semiconducting property with hole and electron mobilities up to 0.12 and 1.89 cm2 V-1 s-1 , and a photoluminescence quantum yield of 55%. One of the crystal forms of 5FDPA exhibits blue emission with an emission quantum yield of 52% and simultaneously shows the n-type semiconducting property with an electron mobility up to 2.65 cm2 V-1 s-1 , which is the highest value among the reported organic emissive n-type semiconductors. Furthermore, crystals of 5FDPP are utilized to fabricate OLETs by using Ag as source-drain electrodes. The electroluminescence is detected in the transporting channels with an external quantum efficiency (EQE) of up to 2.2%, and the current density is up to 145 kA cm-2 , which are among the highest values for single-component OLETs with symmetric electrodes.
ABSTRACT
Intrinsically stretchable polymer semiconductors are highly demanding for flexible electronics. However, it still remains challenging to achieve synergy between intrinsic stretchability and charge transport property properly for polymer semiconductors. In this paper, terpolymers are reported as intrinsically stretchable polymeric semiconductors with good ductility and high charge mobility simultaneously by incorporation of non-centrosymmetric spiro[cycloalkane-1,9'-fluorene] (spiro-fluorene) units into the backbone of diketopyrrolopyrrole (DPP) based conjugated polymers. The results reveal that these terpolymers show obviously high crack onset strains and their tensile moduli are remarkably reduced, by comparing with the parent DPP-based conjugated polymer without spiro-fluorene units. They exhibit simultaneously high charge mobilities (>1.0 cm2 V-1 s-1 ) at 100% strain and even after repeated stretching and releasing cycles for 500 times under 50% strain. The terpolymer P2, in which cyclopropane is linked to the spiro-fluorene unit, is among the best reported intrinsically stretchable polymer semiconductors with record mobility up to 3.1 cm2 V-1 s-1 at even 150% strain and 1.4 cm2 V-1 s-1 after repeated stretching and releasing cycles for 1000 times.