Your browser doesn't support javascript.
loading
Show: 20 | 50 | 100
Results 1 - 15 de 15
Filter
Add more filters










Publication year range
1.
ACS Environ Au ; 4(1): 12-30, 2024 Jan 17.
Article in English | MEDLINE | ID: mdl-38250341

ABSTRACT

Residential wood combustion contributing to airborne particulate matter (PM10) was studied for 1 year at two sites in the village of Melpitz. Significant excess pollution was observed at the Melpitz center compared to that at the TROPOS research station Melpitz reference site, situated only 700 m away. Local concentration increments at the village site for the combustion PM constituents organic carbon, elemental carbon, levoglucosan, and benzo[a]pyrene were determined under appropriate wind directions, and their winter mean values were 0.7 µg m-3, 0.3 µg m-3, 0.1 µg m-3, and 0.4 ng m-3, representing relative increases over the regional background concentration of 24, 70, 61, and 107%, respectively. Yearly, weekly, and diurnal profiles of village increments suggest residential heating as the dominant source of this excess pollution, mainly originating from wood combustion. Receptor modeling using positive matrix factorization quantified 4.5 µg m-3 wood combustion PM at the village site, representing an increment of 1.9 µg m-3 and an increase of ∼75% over the 2.6 µg m-3 regional background wood combustion PM. This increment varied with season, temperature, and boundary layer height and reached daily mean values of 4-6 µg m-3 during unfavorable meteorological conditions. Potential health effects were estimated and resulted in an all-cause mortality from short-term exposure to wood combustion PM of 2.1 cases per 100,000 inhabitants and year for areas with similar wood smoke levels as observed in Melpitz. The excess cancer risk from the concentrations of polycyclic aromatic hydrocarbons was 6.4 per 100,000. For both health metrics, the very local contributions from the village itself were about 40-50%, indicating a strong potential for mitigation through local-scale policies. A compilation of literature data demonstrates wood combustion to represent a major source of PM pollution in Germany, with average winter-time contributions of 10-20%. The present study quantifies the negative impacts of heating with wood in rural residential areas, where the continuous monitoring of air quality is typically lacking. Further regulation of this PM source is warranted in order to protect human health.

2.
Anal Chem ; 94(25): 8966-8974, 2022 06 28.
Article in English | MEDLINE | ID: mdl-35708243

ABSTRACT

Atmospheric particles and droplets contain numerous organic substances, some of which form complexes with metal ions, significantly affecting bulk physicochemical properties and chemical reactivity. However, the detection and identification of complexing agents and their corresponding metal complexes remains an analytical challenge. In this study, we developed an LC/HRMS nontarget screening (NTS) approach which allows the selective detection of complexing agents in aerosol particle extracts and rainwater. To achieve this, a T-junction is installed between the LC outlet and the ion source, and a FeCl3 solution is added for postcolumn complexation. The resulting mass spectra are screened for the three characteristic iron(III)-complexes [M - H + FeCl3]-, [M - 2H + FeCl2]-, and [M - 3H + FeCl]- with mass differences (Δm/z) between the complexing agent and the iron complex of 160.8416, 124.8648, and 89.8959, respectively. Up to 29 di- or tricarboxylic acids were identified as complexing agents in aerosol particle samples from two different sites (Melpitz, Germany, and Wangdu, China) at concentrations as low as 50 nM. Thirteen complexing agents were detected even in measurements without postcolumn iron addition from complexation with background Fe3+ traces from the analytical system. At least for the highest concentrated complexing agents, the proposed screening approach can thus be exploited in a NTS approach without any device modification. Besides carboxylic acids, 4-nitrophenol and 4-nitrocatechol were identified as further complexing agents, demonstrating the applicability of the approach to other matrices and to a range of different complexing agents.


Subject(s)
Ferric Compounds , Iron , Aerosols , Carboxylic Acids/chemistry , Iron/chemistry , Mass Spectrometry/methods
5.
J Sep Sci ; 44(12): 2343-2357, 2021 Jun.
Article in English | MEDLINE | ID: mdl-33822470

ABSTRACT

A method using ion chromatography coupled to high-resolution Orbitrap mass spectrometry was developed to quantify highly-polar organic compounds in aqueous filter extracts of atmospheric particles. In total, 43 compounds, including short-chain carboxylic acids, terpene-derived acids, organosulfates, and inorganic anions were separated within 33 min by a KOH gradient. Ionization by electrospray was maximized by adding 100 µL min-1 isopropanol as post-column solvent and optimizing the ion source settings. Detection limits (S/N ≥ 3) were in the range of 0.075-25 µg L-1 and better than previously reported for 22 compounds. Recoveries of extraction typically range from 85 to 117%. The developed method was applied to three ambient samples, including two arctic flight samples, and one sample from Melpitz, a continental backround research site. A total of 32 different compounds were identified for all samples. From the arctic flight samples, organic tracers could be quantified for the first time with concentrations ranging from 0.1 to 17.8 ng m-3 . Due to the minimal sample preparation, the beneficial figures of merit, and the broad range of accessible compounds, including very polar ones, the new method offers advantages over existing ones and enables a detailed analysis of organic marker compounds in atmospheric aerosol particles.

6.
J Sep Sci ; 43(3): 577-589, 2020 Feb.
Article in English | MEDLINE | ID: mdl-31697033

ABSTRACT

A method using ultra-high performance liquid chromatography coupled to a high resolution Orbitrap mass spectrometer was developed to identify and quantify imidazoles in aqueous extracts of aerosol particles. The aqueous particle extract was used without further enrichment or sample clean-up. Five columns were tested for efficient separation of ten imidazoles and the Acquity HSS T3 column was chosen for further optimization. Low limits of detection (<25 nM) and good intraday and interday repeatability (<1.6 and <6%, respectively) were achieved. Investigation of matrix effects showed that external calibration is applicable when the loading of organic carbon in the sample is below 10 µg m-3 . The developed method was applied to ten real samples, and six out of the ten test imidazoles were successfully quantified, while six further imidazoles were qualitatively identified, among them 4-imidazolecarboxaldehyde and 4-methyl-5-imidazolecarboxaldehyde. Advantages of the method are the minimal sample preparation, the short run time for each sample, and the low detection limits. These allow for a fast and reliable quantification of imidazoles even in a large number of aqueous particle extract samples.

7.
Environ Sci Technol ; 51(9): 5061-5070, 2017 May 02.
Article in English | MEDLINE | ID: mdl-28333457

ABSTRACT

Organic carbon in atmospheric particles comprises a large fraction of chromatographically unresolved compounds, often referred to as humic-like substances (HULIS), which influence particle properties and impact climate, human health, and ecosystems. To better understand its composition, a two-dimensional (2D) offline method combining size-exclusion (SEC) and reversed-phase liquid chromatography (RP-HPLC) using a new spiked gradient profile is presented. It separates HULIS into 55 fractions of different size and polarity, with estimated ranges of molecular weight and octanol/water partitioning coefficient (log P) from 160-900 g/mol and 0.2-3.3, respectively. The distribution of HULIS within the 2D size versus polarity space is illustrated with heat maps of ultraviolet absorption at 254 nm. It is found to strongly differ in a small example set of samples from a background site near Leipzig, Germany. In winter, the most intense signals were obtained for the largest molecules (>520 g/mol) with low polarity (log P ∼ 1.9), whereas in summer, smaller (225-330 g/mol) and more polar (log P ∼ 0.55) molecules dominate. The method reveals such differences in HULIS composition in a more detailed manner than previously possible and can therefore help to better elucidate the sources of HULIS in different seasons or at different sites. Analyzing Suwannee river fulvic acid as a common HULIS surrogate shows a similar polarity range, but the sizes are clearly larger than those of atmospheric HULIS.


Subject(s)
Aerosols , Humic Substances , Carbon , Rivers , Water/chemistry
8.
Environ Sci Technol ; 51(1): 418-426, 2017 01 03.
Article in English | MEDLINE | ID: mdl-27996238

ABSTRACT

Methanesulfonic acid (MSA) has been widely used as a proxy for marine biogenic sources, but it is still a challenge to provide an accurate MSA mass concentration with high time resolution. This study offers an improved MSA quantification method using high resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). Particularly, the method was validated based on an excellent agreement with parallel offline measurements (slope = 0.88, R2 = 0.89). This comparison is much better than those using previously reported methods, resulting in underestimations of 31-54% of MSA concentration. With this new method, MSA mass concentrations were obtained during 4 North/South Atlantic cruises in spring and autumn of 2011 and 2012. The seasonal and spatial variation of the particulate MSA mass concentration as well as the MSA to non-sea-salt sulfate ratio (MSA:nssSO4) over the North/South Atlantic Ocean were determined for the first time. Seasonal variation of the MSA mass concentration was observed, with higher values in spring (0.03 µg m-3) than in autumn (0.01 µg m-3). The investigation of MSA:nssSO4 suggests a ubiquitous and significant influence of anthropogenic sources on aerosols in the marine boundary layer.


Subject(s)
Aerosols , Mass Spectrometry , Air Pollutants , Climate , Sulfates
11.
Environ Sci Technol ; 50(3): 1166-73, 2016 Feb 02.
Article in English | MEDLINE | ID: mdl-26726845

ABSTRACT

Imidazoles are widely discussed in recent literature. They have been studied as a secondary product of the reaction of dicarbonyls with nitrogen containing compounds in a number of laboratory studies, potentially acting as photosensitizers triggering secondary organic aerosol growth and are forming constituents of light absorbing brown carbon. Despite the knowledge from laboratory studies, no quantitative information about imidazoles in ambient aerosol particles is available. Within the present study, five imidazoles (1-butylimidazole, 1-ethylimidazole, 2-ethylimidazole, imidazol-2-carboxaldehyde, and 4(5)-methylimidazole) were successfully identified and quantified for the first time in ambient aerosol samples from different environments in Europe and China. Their concentrations range between 0.2 and 14 ng/m(3). 4(5)-Methylimidazole was found to be the most abundant imidazole. The occurrence of imidazoles seems to be favored at sites with strong biomass burning influence or connected to more polluted air masses. No connection was found between aerosol particle pH and imidazole concentration. Our work corroborates the laboratory studies by showing that imidazoles are present in ambient aerosol samples in measurable amounts. Moreover, it further motivates to explore the potential photosensitizing properties of small alkyl-substituted imidazoles.


Subject(s)
Aerosols/analysis , Air Pollutants/analysis , Carbon/analysis , Imidazoles/analysis , Photosensitizing Agents/analysis , Aerosols/chemistry , China , Environmental Monitoring/methods , Europe , Photosensitizing Agents/chemistry
12.
Environ Sci Technol ; 49(21): 12688-96, 2015 Nov 03.
Article in English | MEDLINE | ID: mdl-26422664

ABSTRACT

Deposition of atmospheric constituents--either gas phase or particulate--onto urban impervious surfaces gives rise to a thin "urban grime" film. The area exposed by these impervious surfaces in a typical urban environment is comparable to, or greater than, that of particles present in the urban boundary layer; however, it is largely overlooked as a site for heterogeneous reactions. Here we present the results of a field campaign to determine and compare the chemical composition of urban grime and of particles collected simultaneously during the autumn of 2014 at an urban site in central Leipzig, Germany. We see dramatically reduced ammonium and nitrate levels in the film as compared to particles, suggesting a significant loss of ammonium nitrate, thus enhancing the mobility of these species in the environment. Nitrate levels are 10% lower for films exposed to sunlight compared to those that were shielded from direct sun, indicating a possible mechanism for recycling nitrate anion to reactive nitrogen species. Finally, chloride levels in the film suggest that urban grime could represent an unrecognized source of continental chloride available for ClNO2 production even in times of low particulate chloride. Such source and recycling processes could prove to be important to local and regional air quality.


Subject(s)
Air Pollutants/analysis , Environmental Pollutants/chemistry , Chlorides/analysis , Cities , Environmental Monitoring/methods , Environmental Pollutants/analysis , Germany , Nitrates/chemistry , Reactive Nitrogen Species/chemistry
13.
Electrophoresis ; 35(9): 1353-61, 2014 May.
Article in English | MEDLINE | ID: mdl-24347320

ABSTRACT

A hollow-fiber liquid-phase microextraction method was developed to enrich nine nitrophenolic compounds from aqueous extracts of atmospheric aerosol particles. Analysis was performed by CE coupled with ESI MS. The BGE composition was optimized to a 20 mM ammonium acetate buffer at pH 9.7 containing 15% methanol v/v. Several extraction parameters (composition of organic liquid membrane, pH of acceptor phase, salting-out effect, extraction time) were investigated for their effect on the analyte recoveries. The donor phase consisted of a 1.8 mL sample solution kept at pH 2 while the acceptor phase was a 15 µL 100 mM aqueous ammonia solution. Dihexyl ether served as supported liquid membrane. Low detection limits in the range of nanomole per liter were achieved. Recoveries of aqueous standard solutions were found to be between 11 and 90% with enrichment factors between 10 and 100. Interday and intraday repeatabilities were in an acceptable range for most compounds (6-15% and 7-10%, respectively) but somewhat higher for 4-nitrocatechol (59 and 48%) and 2-nitrophenol (17 and 35%). The developed method was found to be competitive with more established method and was successfully applied to samples of atmospheric particulate matter from field experiments.


Subject(s)
Air Pollutants/analysis , Electrophoresis, Capillary/methods , Liquid Phase Microextraction/methods , Nitrophenols/analysis , Air Pollutants/chemistry , Air Pollutants/isolation & purification , Hydrogen-Ion Concentration , Mass Spectrometry/methods , Nitrophenols/chemistry , Nitrophenols/isolation & purification , Reproducibility of Results , Sodium Chloride
14.
Science ; 340(6133): 727-30, 2013 May 10.
Article in English | MEDLINE | ID: mdl-23661757

ABSTRACT

Global sulfate production plays a key role in aerosol radiative forcing; more than half of this production occurs in clouds. We found that sulfur dioxide oxidation catalyzed by natural transition metal ions is the dominant in-cloud oxidation pathway. The pathway was observed to occur primarily on coarse mineral dust, so the sulfate produced will have a short lifetime and little direct or indirect climatic effect. Taking this into account will lead to large changes in estimates of the magnitude and spatial distribution of aerosol forcing. Therefore, this oxidation pathway-which is currently included in only one of the 12 major global climate models-will have a significant impact on assessments of current and future climate.


Subject(s)
Atmosphere/chemistry , Climate , Dust , Sulfur Dioxide/chemistry , Aerosols , Catalysis , Minerals/chemistry , Oxidation-Reduction , Transition Elements
15.
J Chromatogr A ; 1171(1-2): 112-23, 2007 Nov 09.
Article in English | MEDLINE | ID: mdl-17920610

ABSTRACT

A capillary electrophoresis/electrospray ionisation mass spectrometry (CE/ESI-MS) method was developed for the determination of 38 organic acids in atmospheric particles and cloud water. The target analytes include many functionalised carboxylic acids, such as carboxylic acids with additional oxo-, hydroxy- or nitro-groups. These compounds are of large interest as their determination might give new insights into the atmospheric multiphase chemistry. OASIS HLB sorbent material (Waters) was used to extract and enrich polar carboxylic acids from aqueous solutions with recoveries greater than 80% for most analytes. Relative standard deviations in the range of 4-20% for peak areas (n=5), including the SPE step, and 0.2-0.5% (n=8) for migration times were found. The limits of detection (S/N=3) ranged from 0.005 to 0.6 micromol l(-1) for an ion-trap mass spectrometer and from 0.0004 to 0.08 micromol l(-1) for a time-of-flight mass spectrometer. These detection limits translate into atmospheric concentrations in the low pg m(-3) range based on the experimental conditions in this study. Severe matrix effects were observed for real samples, arising from complex co-extracted organic material. However, using the method of standard addition, most of the analytes could successfully be quantified in samples of ambient particles and cloud water with concentrations in the low ng m(-3) to high pg m(-3) range. These results demonstrate the suitability of the proposed method for the determination of a wide range of polar carboxylic acids at low concentrations in complex samples of different atmospheric phases.


Subject(s)
Air Pollutants/analysis , Carboxylic Acids/analysis , Electrophoresis, Capillary/methods , Environmental Monitoring/methods , Spectrometry, Mass, Electrospray Ionization/methods , Air Pollutants/chemistry , Atmosphere/analysis , Atmosphere/chemistry , Carboxylic Acids/chemistry , Reproducibility of Results , Sensitivity and Specificity , Water/chemistry
SELECTION OF CITATIONS
SEARCH DETAIL