Image-Based Computational Fluid Dynamics to Compare Two Repair Techniques for Mitral Valve Prolapse.

OBJECTIVE : The treatment of mitral valve prolapse involves two distinct repair techniques: chordal replacement (Neochordae technique) and leaflet resection (Resection technique). However, there is still a debate in the literature about which is the optimal one. In this context, we performed an image-based computational fluid dynamic study to evaluate blood dynamics in the two surgical techniques. METHODS : We considered a healthy subject (H) and two patients (N and R) who underwent surgery for prolapse of the posterior leaflet and were operated with the Neochordae and Resection technique, respectively. Computational Fluid Dynamics (CFD) was employed with prescribed motion of the entire left heart coming from cine-MRI images, with a Large Eddy Simulation model to describe the transition to turbulence and a resistive method for managing valve dynamics. We created three different virtual scenarios where the operated mitral valves were inserted in the same left heart geometry of the healthy subject to study the differences attributed only to the two techniques. RESULTS : We compared the three scenarios by quantitatively analyzing ventricular velocity patterns and pressures, transition to turbulence, and the ventricle ability to prevent thrombi formation. From these results, we found that the operative techniques affected the ventricular blood dynamics in different ways, with variations attributed to the reduced mobility of the Resection posterior leaflet. Specifically, the Resection technique resulted in turbulent forces, related with the risk of hemolysis formation, up to 640 Pa, while the other two scenarios exhibited a maximum of 240 Pa. Moreover, in correspondence of the ventricular apex, the Resection technique reduced the areas with low velocity to 15%, whereas the healthy case and the Neochordae case maintained these areas at 30 and 48%, respectively. Our findings suggest that the Neochordae technique developed a more physiological flow with respect to the Resection technique. CONCLUSION: Resection technique gives rise to a different direction of the mitral jet during diastole increasing the ability to washout the ventricular apex preventing from thrombi formation, but at the same time it promotes turbulence formation that is associated with ventricular effort and risk of hemolysis.

Discovery of delayed gas production after implantation of a continuous-flow left ventricular assist device and a preliminary exploration of the mechanisms of its occurrence.

Objective: To characterize the gas production phenomenon in the animal model of left ventricular assist device (LVAD), and study its mechanism. Methods: An in vitro bubble precipitation experiment was conducted, and the blood samples of Parma spp. animals were divided into ordinary group and oxygen-enriched group according to whether they were oxygenated or not at the time of blood collection, and a static control group was set up respectively. Blood gases were drawn and analyzed before and after the experiment. Activate the pump, and the number of air bubbles in the loop was measured by ultrasound at different rotational speeds; CFD was applied to simulate the flow field in the blood pump, and pressure, fluid velocity vector and shear force diagrams were plotted, and a thrombus model was constructed and the flow field was simulated and plotted as a cloud diagram. Results: There was a statistical difference in the number of bubbles in the inflow and outflow tubes of the blood pump (P values of 0.04 and 0.023, respectively), and the number of bubbles in the outflow tubes of both groups was significantly higher than the number of bubbles in the inflow tubes. The number of bubbles in the tubes of both the oxygen-enriched and normal groups was significantly higher than that in the inflow group. In both the normal and oxygen-enriched groups, more gas was produced at higher speeds than at lower speeds. Blood gas analysis showed that the reduced gas composition in the blood was mainly oxygen. Flow field simulation results: the high rotation speed group had lower central pressure and greater scalar shear. The thrombus simulation group was more prone to turbulence, sudden pressure changes, and greater shear than the normal group. Conclusion: Blood gas production is associated with higher partial pressures of blood oxygen, higher rotation speed, and intrapump thrombosis, and the mechanism of pump gas production is degassing of dissolved gases rather than cavitation of water, and the gas released is most likely to have oxygen. The degassing phenomenon is an warning factor for pump thrombosis.

A Pseudo-Spectral Method for Wall Shear Stress Estimation from Doppler Ultrasound Imaging in Coronary Arteries.

PURPOSE: The Wall Shear Stress (WSS) is the component tangential to the boundary of the normal stress tensor in an incompressible fluid, and it has been recognized as a quantity of primary importance in predicting possible adverse events in cardiovascular diseases, in general, and in coronary diseases, in particular. The quantification of the WSS in patient-specific settings can be achieved by performing a Computational Fluid Dynamics (CFD) analysis based on patient geometry, or it can be retrieved by a numerical approximation based on blood flow velocity data, e.g., ultrasound (US) Doppler measurements. This paper presents a novel method for WSS quantification from 2D vector Doppler measurements. METHODS: Images were obtained through unfocused plane waves and transverse oscillation to acquire both in-plane velocity components. These velocity components were processed using pseudo-spectral differentiation techniques based on Fourier approximations of the derivatives to compute the WSS. RESULTS: Our Pseudo-Spectral Method (PSM) is tested in two vessel phantoms, straight and stenotic, where a steady flow of 15 mL/min is applied. The method is successfully validated against CFD simulations and compared against current techniques based on the assumption of a parabolic velocity profile. The PSM accurately detected Wall Shear Stress (WSS) variations in geometries differing from straight cylinders, and is less sensitive to measurement noise. In particular, when using synthetic data (noise free, e.g., generated by CFD) on cylindrical geometries, the Poiseuille-based methods and PSM have comparable accuracy; on the contrary, when using the data retrieved from US measures, the average error of the WSS obtained with the PSM turned out to be 3 to 9 times smaller than that obtained by state-of-the-art methods. CONCLUSION: The pseudo-spectral approach allows controlling the approximation errors in the presence of noisy data. This gives a more accurate alternative to the present standard and a less computationally expensive choice compared to CFD, which also requires high-quality data to reconstruct the vessel geometry.

A synergistic approach combining computational fluid dynamics simulation with hydrolysis-acidification for dye wastewater treatment.

Wastewater treatment is effectively conducted using anaerobic biological methods. Nevertheless, the efficiency of these methods can be hindered by challenges like short-circuits and dead zones, particularly in treating persistent contaminants. This work utilized computational fluid dynamics (CFD) simulations to enhance water distribution, ensuring uniform interactions between solid and liquid phases, and thus mitigating issues related to short-circuits and dead zones. Such enhancements notably amplified the anaerobic biological process's efficiency. Furthermore, dye biodegradability was improved through the application of the hydrolysis acidification technique. Optimal hydraulic retention time for the hydrolysis-acidification reactor, established at 9 h, was determined via sludge cultivation and domestication for stable operation. During stable operation, an elevation in effluent volatile fatty acids was observed, alongside a COD removal rate fluctuating between 15% and 29%. Approximately 50% was noted as the rate of color removal. Simultaneously, a noticeable decrease in effluent pH occurred, with total nitrogen removal approximating 8%. An estimated BOD5/COD ratio of 0.32 was recorded. The incorporation of microbial agents led to an enhanced COD removal, ranging from 28% to 33%, thereby stabilizing the effluent BOD5/COD ratio at around 0.35. This research highlights the advantages of optimizing water distribution in anaerobic reactors, particularly when combined with hydrolysis-acidification techniques, effectively addressing issues of short-circuits and dead zones.

Evaluating the efficacy of the punch-out technique in systemic-to-pulmonary shunts: A computational fluid dynamics approach.

BACKGROUND: Systemic-to-pulmonary shunt is a palliative procedure used to decrease pulmonary blood flow in congenital heart diseases. Shunt stenosis or occlusion has been reported to be associated with mortality; therefore, the management of thrombotic complications remains a challenge for most congenital cardiovascular surgeons. Despite its importance, the optimal method for shunt anastomosis remains unclear. OBJECTIVE: The study investigates the clinical benefits of the punch-out technique over conventional methods in the anastomosis process of Systemic-to-pulmonary shunt, focusing on its potential to reduce shunt-related complications. METHODS: Anastomotic models were created by two different surgeons employing both traditional slit and innovative punch-out techniques. Computational tomography was performed to construct three-dimensional models for computational fluid dynamics (CFD) analysis. We assessed the flow pattern, helicity, magnitude of wall shear stress, and its gradient. RESULTS: The anastomotic flow area was larger in the model using the punch-out technique than in the slit model. In CFD simulation, we found that using the punch-out technique decreases the likelihood of establishing a high wall shear stress distribution around the anastomosis line in the model. CONCLUSION: The punch-out technique emerges as a promising method in SPS anastomosis, offering a reproducible and less skill-dependent alternative that potentially diminishes the risk of shunt occlusion, thereby enhancing patient outcomes.

Hemodynamic influence of mild stenosis morphology in different coronary arteries: a computational fluid dynamic modelling study.

Introduction: Mild stenosis [degree of stenosis (DS) < 50%] is commonly labeled as nonobstructive lesion. Some lesions remain stable for several years, while others precipitate acute coronary syndromes (ACS) rapidly. The causes of ACS and the factors leading to diverse clinical outcomes remain unclear. Method: This study aimed to investigate the hemodynamic influence of mild stenosis morphologies in different coronary arteries. The stenoses were modeled with different morphologies based on a healthy individual data. Computational fluid dynamics analysis was used to obtain hemodynamic characteristics, including flow waveforms, fractional flow reserve (FFR), flow streamlines, time-average wall shear stress (TAWSS), and oscillatory shear index (OSI). Results: Numerical simulation indicated significant hemodynamic differences among different DS and locations. In the 20%-30% range, significant large, low-velocity vortexes resulted in low TAWSS (<4 dyne/cm2) around stenoses. In the 30%-50% range, high flow velocity due to lumen area reduction resulted in high TAWSS (>40 dyne/cm2), rapidly expanding the high TAWSS area (averagely increased by 0.46 cm2) in left main artery and left anterior descending artery (LAD), where high OSI areas remained extensive (>0.19 cm2). Discussion: While mild stenosis does not pose any immediate ischemic risk due to a FFR > 0.95, 20%-50% stenosis requires attention and further subdivision based on location is essential. Rapid progression is a danger for lesions with 20%-30% DS near the stenoses and in the proximal LAD, while lesions with 30%-50% DS can cause plaque injury and rupture. These findings support clinical practice in early assessment, monitoring, and preventive treatment.

Haemodynamic effects of non-Newtonian fluid blood on the abdominal aorta before and after double tear rupture.

OBJECTIVES: Intimal tears caused by aortic dissection can weaken the arterial wall and lead to aortic aneurysms. However, the effect of different tear states on the blood flow behaviour remains complex. This study uses a novel approach that combines numerical haemodynamic simulation with in vitro experiments to elucidate the effect of arterial dissection rupture on the complex blood flow state within the abdominal aneurysm and the endogenous causes of end-organ malperfusion. MATERIALS AND METHODS: Based on the CT imaging data and clinical physiological parameters, the overall arterial models including aortic dissection and aneurysm with single tear and double tear were established, and the turbulence behaviours and haemodynamic characteristics of arterial dissection and aneurysm under different blood pressures were simulated by using non-Newtonian flow fluids with the pulsatile blood flow rate of the clinical patients as a cycle, and the results of the numerical simulation were verified by in vitro simulation experiments. RESULTS: Hemodynamic simulations revealed that the aneurysm and single-tear false lumen generated a maximum pressure of 320.591 mmHg, 267 % over the 120 mmHg criterion. The pressure differential generates reflux, leading to a WSS of 2247.9 Pa at the TL inlet and blood flow velocities of up to 6.41 m/s inducing extend of the inlet. DTD Medium FL instantaneous WP above 120 mmHg Standard 151 % Additionally, there was 82.5 % higher flow in the right iliac aorta than in the left iliac aorta, which triggered malperfusion. Thrombus was accumulated distal to the tear and turbulence. These results are consistent with the findings of the in vitro experiments. CONCLUSIONS: This study reveals the haemodynamic mechanisms by which aortic dissection induces aortic aneurysms to produce different risk states. This will contribute to in vitro simulation studies as a new fulcrum in the process of moving from numerical simulation to clinical trials.

Unsteady CFD simulation of a rotor blade under various wind conditions.

Wind and gusts can significantly impact the performance of rotors and turbines. The transient behavior of the rotor should be carefully examined to account for these effects. This paper investigates the unsteady aerodynamic characteristics of a rotor blade under different wind conditions, such as direction, speed, and angle. A 3D transient Computational Fluid Dynamics (CFD) simulation using the dynamic mesh technique is performed to analyze the rotor dynamics. The unsteady Reynolds-averaged Navier-Stokes (URANS) equations with the k-ω SST turbulence model are solved. The rotor blade used for this study is the U15XXL Combo KV29 industrial blade, which has not been numerically analyzed before. The results show that wind in the same direction as the rotation reduces the thrust more than lateral or opposite wind. Lateral wind with a speed lower than 5 m/s decreases the blade performance, but higher speeds increase it. Higher lateral wind speeds also cause two peaks in the torque curve, forming a butterfly wing shape in the polar torque plot and multiple extrema in the torque curve with increasing speed. The maximum thrust shifts slightly to the left with increasing lateral wind speed. The lateral angle does not affect the average thrust produced in one blade revolution but only causes a spatial shift. The thrust production decreases as the angle approaches the opposite direction of rotation. The motion amplitude decreases, and the curve becomes smoother as this angle increases. A nearly straight line similar to no side wind is observed at 60 and 90 degrees, which is attributed to the constant effective angle of attack during the rotation cycle.

Enhancing precision in effective regurgitant orifice area estimation by transthoracic echocardiography for functional mitral regurgitation using computational fluid dynamics.

Computational fluid dynamics (CFD) was used to identify factors influencing the accuracy of the hemispherical proximal isovelocity surface area (PISA) method in calculating the effective regurgitant orifice area (EROA) for patients with functional mitral regurgitation (FMR). Ninety-nine CFD models were constructed to investigate the impact of regurgitant orifice shape and leaflet tethering on the EROA calculation using the PISA method. The correction factors for regurgitation orifice shape (CFs) and for leaflet tethering (CFt) were derived by comparing the 2D PISA method and the actual orifice area. The correction formula was then tested in vivo via 2D transthoracic echocardiography with 3D transesophageal echocardiography of the vena contracta area (VCA) as a reference method in 62 patients with FMR. Based on the CFD simulation results, the two major factors for correcting the EROA calculation were vena contracta length (VCL) and coaptation depth (CD). The correction formula for the EROA was corrected effective regurgitant orifice area (CEROA) = EROA*CFs*CFt, where CFs = 0.59 × VCL(cm) + 0.6 × MR Vmax(cm/s)-0.63 × PISA R(cm)-1.51 and CFt = 0.4 × CD (cm) + 0.96. The correction formula was applied to FMR patients, and the bias and LOA between the CEROA and VCA (0.01 ± 0.13 cm2) were much smaller than those between the EROA and VCA (0.26 ± 0.32 cm2). The CFD-based correction formula improves the accuracy of the EROA calculation based on the hemispheric PISA method, possibly leading to more accurate and reliable data for treatment decision-making in FMR patients.

Validation of classification system for isolated superior mesenteric artery dissections using image-based computational flow analysis.

BACKGROUND AND OBJECTIVE: The isolated superior mesenteric artery dissection (ISMAD) is a rare but potentially fatal vascular disorder. Classifications for ISMAD were previously proposed based on morphometric features. However, the classification systems were not standardized and verified yet. This study conducted computational flow analysis to validate the latest classification system of ISMAD and aid clinical decision-making based on hemodynamic parameters. METHODS: 62 patients with ISMAD were included and classified into different types according to false lumen structures (five types, Type I-V) and true lumen patency (two types, Type P and Type S) according to Qiu classification system. Computational fluid dynamics and three-dimensional structural analyses were conducted on the basis of computed tomography angiography datasets. Quantitative and qualitative functional analyses were performed via parameters of interest including volume flow of each minute, pressure drop, pressure gradient, the derivative parameters of wall shear stress such as time-averaged wall shear stress (TAWSS), oscillatory shear index (OSI), and the relative residence time (RRT). Statistical analyses were conducted among different ISMAD types. RESULTS: TAWSS, OSI and RRT showed significant difference among different types when classified using false lumen structures. In detail, Type IV showed significantly higher TAWSS than other types (p = 0.007). OSI was obviously higher in Type II (p = 0.015). Type IV also presented the lowest RRT (p = 0.005). The pressure drop, pressure gradient, OSI and RRT showed higher value in Type S than that in Type P, demonstrating a statistical significance with p values of 0.017, 0.041, 0.001 and 0.012, respectively. While Type P had larger volume flow than Type S (p = 0.041). CONCLUSIONS: The notable differences in hemodynamic features among different types demonstrated the feasibility of Qiu classification system. The evaluation based on hemodynamic simulation might also provide insights into risk identification and guide therapeutic decisions for ISMAD.

Experimental broad-based curved sidewall aneurysms in rabbits mimicking human carotid siphon aneurysms: proof of feasibility and comparability using computational fluid dynamics.

PURPOSE: Broad-based sidewall aneurysms of the carotid artery are primarily treated endovascularly. However, recurrence or rupture after treatment still pose a significant risk. Hence, reliable animal models mimicking this aneurysm type are essential for to evaluate the performance of new advanced endovascular devices. METHODS: Experimental aneurysms were created in 12 New Zealand white rabbits (2.5-3.5kg). The human carotid siphon was mimicked with an end-to-end anastomosis of both common carotid arteries. A venous pouch was sutured on the convexity to mimic a broad-based side wall aneurysm. Patency and configuration was investigated 4 weeks postoperatively by 3 T-MRA. To compare flow conditions of broad-based sidewall aneurysms in rabbits and humans exemplary computational fluid dynamics (CFD) simulations were performed using species specific blood viscosity values. RESULTS: We were able to achieve 0% peri- or postoperative mortality. Patency was confirmed by 3T-MRA in 11 out of 12 aneurysms (91.7%). Aneurysm lengths ranged from 6.4 - 9.8mm and aneurysm necks from 7.3-9.8mm. CFD showed simple flow profiles with one vortex in rabbit as well as in human aneurysms. Wall shear stress (WSS) rates were comparable using species-specific blood viscosity values (rabbit mean 1.65 Pa vs. human mean 1.7 Pa). CONCLUSION: The broad-based curved sidewall aneurysm model mimicking the carotid siphon showed high aneurysm patency rates with low morbidity. High comparability with human flow patterns and human intranaeurysmal biomechanical forces was shown using simulations.

Common iliac artery aneurysm with narrow inner lumen treated by a novel surgeon-modified inner branch iliac branch device.

OBJECTIVES: The iliac branch device (IBD) has emerged as the optimal method for endovascular reconstruction of internal iliac artery (IIA). However, due to its high anatomical requirements, the applicability rate among East Asians is limited, especially for common iliac artery aneurysm (CIAA) with narrow inner lumen cases. Here, we report a case with narrow distal inner lumen of the CIAA treated with a novel surgeon-modified inner branch iliac branch device (IIBD). METHODS: This is a case report, and consent for publication was obtained from the patient. RESULTS: The 1-year follow-up CTA showed that the CIAA regressed without abdominal pain. Right CIA, external iliac artery, and IIA were all patent. CONCLUSIONS: The IIBD technique has lower anatomical requirements for the CIA. Therefore, it may be a feasible option for IIA preservation in cases of CIAA with narrow inner lumen.

Effect of differences in proximal neck angles on biomechanics of abdominal aortic aneurysm based on fluid dynamics.

BACKGROUND: This study aimed to analyze the effect of proximal neck angulation on the biomechanical indices of abdominal aortic aneurysms (AAA) and to investigate its impact on the risk of AAA rupture. METHODS: CT angiography (CTA) data of patients with AAA from January 2015 to January 2022 were collected. Patients were divided into three groups based on the angle of the proximal neck: Group A (âˆ ß ≤ 30°), Group B (30°<âˆ ß ≤ 60°), and Group C (âˆ ß > 60°). Biomechanical indices related to the rupture risk of AAA were analyzed using computational fluid dynamics modeling (CFD-Post) based on the collected data. RESULTS: Group A showed slight turbulence in the AAA lumen with a mixed laminar flow pattern. Group B had a regular low-speed eddy line characterized by cross-flow dominated by lumen blood flow and turbulence. In Group C, a few turbulent lines appeared at the proximal neck, accompanied by eddy currents in the lumen expansion area following the AAA shape. Significant differences were found in peak wall stress, shear stress, and the maximum blood flow velocity impact among the three groups. The maximum blood flow velocity at the angle of the proximal neck impact indicated the influence of the proximal neck angle on the blood flow state in the lumen. CONCLUSION: As the angle of the proximal neck increased, it caused stronger eddy currents and turbulent blood flow due to a high-speed area near the neck. The region with the largest diameter in the abdominal aortic aneurysm was prone to the highest stress, indicating a higher risk of rupture. The corner of the proximal neck experienced the greatest shear stress, potentially leading to endothelial injury and further enlargement of the aneurysm.

Oxymetazoline as a predictor of turbinate reduction surgery outcomes: Objective support from a prospective, single-blinded, computational fluid dynamics study.

BACKGROUND: A patient's subjective response to topical nasal decongestant is often used to screen for turbinate reduction surgery suitability. However, this anecdotal strategy has not been objectively and quantitatively evaluated. METHODS: Prospective, longitudinal, and single-blinded cohort study employing computational fluid dynamic modeling based on computed tomography scans at baseline, 30 min postoxymetazoline, and 2 months postsurgery on 11 patients with chronic turbinate hypertrophy. RESULTS: Nasal obstruction symptom evaluation (NOSE) and visual analogue scale (VAS) obstruction scores significantly improved from baseline to postoxymetazoline and again to postsurgery (NOSE: 71.82 ± 14.19 to 42.27 ± 25.26 to 22.27 ± 21.04; VAS: 6.09 ± 2.41 to 4.14 ± 2.20 to 2.08 ± 1.56; each interaction p < 0.05), with significant correlation between the latter two states (r∼0.37-0.69, p < 0.05). Oxymetazoline had a broader anatomical impact throughout inferior and middle turbinates than surgery (many p < 0.05); however, the improvement in regional airflow is similar (most p > 0.05) and predominantly surrounding the inferior turbinate. Strong postoxymetazoline to postsurgery correlations were observed in decreased nasal resistance (r = 0.79, p < 0.05), increased regional airflow rates (r = -0.47 to -0.55, p < 0.05) and regional air/mucosa shear force and heat flux (r = 0.43 to 0.58, p < 0.05); however, only increasing peak heat flux significantly correlated to symptom score improvement (NOSE: r = 0.48, p < 0.05). CONCLUSION: We present the first objective evidence that the "topical decongestant test" can help predict turbinate reduction surgery outcomes. The predictive effect is driven by similar improvementin regional airflow that leading to improved air/mucosa stimulations (peak heat flux) rather than through reduced nasal resistance.

Controlled preparation of curcumin nanocrystals by detachable stainless steel microfluidic chip.

Microfluidic technology has not been extensively utilized in nanocrystals manufacture, although it has been used in the production of liposomes and LNPs. This is mainly due to concerns including blockage of narrow pipes and corrosion of organic solvents on chips. In this study, a detachable stainless steel microfluidic chip with split-and-recombine (SAR) structure was engraved and used to prepare curcumin nanocrystal suspensions by a microfluidic-antisolvent precipitation method. A simulation study of the mixing activities of three chip structures was conducted by COMSOL Multiphysics software. Then the curcumin nanocrystals preparation was optimized by Box-Behnken design to screen different stabilizers and solvents. Two curcumin nanocrystals formulations with an average particle size of 59.29 nm and 168.40 nm were obtained with PDIs of 0.131 and 0.058, respectively. Compared to curcumin powder, the formulation showed an increase in dissolution rate in 0.1 M HCL while pharmacokinetic study indicated that Cmax was increased by 4.47 and 3.14 times and AUC0-∞ were 4.26 and 3.14 times greater. No clogging or deformation of the chip was observed after long usage. The results demonstrate that the stainless steel microfluidic chips with SAR structure have excellent robustness and controllability. It has the potential to be applied in GMP manufacturing of nanocrystals.

Characterisation of hydraulic properties of commercial gas diffusion layers: Toray, SGL, MGL, woven carbon cloth.

This study utilises computational fluid dynamics simulations with the OpenFOAM computational framework to investigate and compare the in-plane and through-plane permeability properties of four different gas diffusion layers (GDLs). Also the through-plane water and air relative permeability values and water saturations at different rates were simulated. Permeability analysis enhances our understanding of fluid flow, ways to decrease pressure loss in the GDL, and methods to enhance oxygen concentration at the catalyst layer interface through convection. The analysis reveals that the investigated GDL materials have spatial heterogeneity of porosity and permeability, especially in the Sigracet SGL 25 BA GDL. However, the porosity and permeability of the Toray TGP-H 060 and AvCarb 370 MGL GDLs exhibit less variations. The two-phase flow studies on GDL saturation show that at the same water injection flowrate, the AvCarb 370 MGL GDL has the largest remaining water saturation, with Sigracet SGL 25 BA GDL being the less saturated GDL among the four investigated GDLs. The compression from the ribs significantly affected the in-plane permeabilities of both Toray TGP-H 060 and especially impacted Sigracet SGL 25 BA GDL. This impact was expected as the pore size distribution varied significantly in the areas under the ribs versus the channel.

Computational model-based hemodynamic comparisons of traditional and modified idealized models of autologous radiocephalic fistula.

Autologous arteriovenous fistula (AVF) is a commonly used vascular access (VA) for hemodialysis, and hemodynamic changes are one of the main factors for its failure. To explore the effect of geometry on the hemodynamics in the AVF, a modified model is built with a gradual and smooth turn at the anastomosis and is compared with the traditional model, which has an abrupt sharp turn at the anastomisis. Transient computational fluid dynamics (CFD) simulations were performed for the comparison and analysis of the hemodynamic fields of the two models at different stages of the pulse cycle. The results showed that the low shear stress region and high oscillatory shear stress region in the modified AVF model coincided with regions of intimal hyperplasia that have been identified by previous studies. A comparison with the blood flow velocities measured in vivo was performed, and the error between the simulation results and the medical data was reduced by 22% in the modified model, which verifies the rationality and utility of the modified model.

Impact of reconstructed portal vein morphology on postoperative nutritional status in pancreatoduodenectomy: a computational fluid dynamics study.

This study evaluated the impact of reconstructed portal vein/superior mesenteric vein (PV/SMV) morphology on the long-term nutritional status following pancreatoduodenectomy (PD) using computational fluid dynamics (CFD). Twenty-four patients who underwent PD with PV/SMV resection and reconstruction without tumor recurrence for over 9 months after the operation were enrolled in the study. Three-dimensional models were constructed from computed tomography images obtained 3-6 months postoperatively. The pressure (p) at the inlet and turbulence dissipation rate (ε) at the outlet were investigated in the models. Patients with values of either p or ε above the upper interquartile range were classified as the poor flow group. The prognostic nutritional index improvement rate was significantly lower at 9 postoperative months in the poor flow group than in the good flow group (P = 0.016). This finding indicates the utility of a CFD analysis for evaluating the reconstructed PV/SMV morphology.

Mixing properties of coronary infusion catheters assessed by in vitro experiments and computational fluid dynamics.

Aims: Continuous infusion thermodilution is an established technique for the assessment of absolute coronary blood flow and microvascular resistance due to its proven accuracy and reproducibility. However, for this technique to yield reliable measurements, direct and homogenous mixing of injected saline and blood is mandatory. This study aimed to assess and compare the mixing properties of two different microcatheters, namely the Rayflow® (with sideholes for infusion) and the Finecross® catheter (single end-hole for infusion), which are commonly used in the catheterization laboratory. Methods and results: The study employed three different methods to evaluate the mixing properties of the catheters. Firstly, a qualitative assessment of mixing was performed using ink injections in an in vitro bench model of a coronary artery. Secondly, in analogy to the human catheterization laboratory, mixing properties over the length of the coronary artery were assessed semi-quantitatively by temperature measurements in the bench model. Lastly, a quantitative assessment was performed by 3D computational fluid dynamics, where the standard deviation and entropy ratio of the temperature over the cross-section in the coronary artery model were calculated for both catheters. Conclusion: All three evaluation methods demonstrated that the Rayflow catheter's specific design leads to a more optimal, homogeneous mixture of blood and saline over both the cross-section and length of a coronary vessel, as compared with the standard end-hole catheter.