Laser-induced graphene non-enzymatic glucose sensors for on-body measurements.

Non-enzymatic glucose sensors outperform enzymatic ones in terms of cost, sensitivity, stability, and operating duration. Though highly sensitive, it is still desirable to further improve the sensitivity of non-enzymatic glucose sensors to detect a trace amount of glucose in sweat and other biofluids. Among the demonstrated effective approaches using bimetals or 3D porous structures, the porous laser-induced graphene (LIG) on flexible polymers showcases good conductivity and a simple fabrication process for the integration of sensing materials. The uniform electroless plating of the nickel and gold layer on LIG electrodes demonstrates significantly enhanced sensitivity and a large linear range for glucose sensing. The sensor with the porous LIG foam exhibits a high sensitivity of 1080 µA mM-1 cm-2, whereas a further increased sensitivity of 3500 µA mM-1 cm-2 is obtained with LIG fibers (LIGF). Impressively, a large linear range (0-30 mM) can be achieved by changing the bias voltage from 0.5 to 0.1 V due to the Au coating. Because the existing non-enzymatic glucose sensors are limited to use in basic solutions, their application in wearable electronics is elusive. In addition to the reduced requirement for the basic solution, this work integrates a porous encapsulating reaction cavity containing alkali solutions with a soft, skin-interfaced microfluidic component to provide integrated microfluidic non-enzymatic glucose sensors for sweat sampling and glucose sensing. The accurate glucose measurements from the human sweat and cell culture media showcase the practical utility, which opens up opportunities for the non-enzymatic glucose sensors in wearable electronics.

A three-dimensional nerve guide conduit based on graphene foam/polycaprolactone.

In this study, a novel nerve guide conduit was developed, based on a three-dimensional (3D) graphene conductive core grown, by chemical vapor deposition (CVD) coupled with a polycaprolactone (PCL) polymer coating. Firstly, the monolithic 3D-graphene foam (3D-GF) was synthesized on Ni foam templates via inductive heating CVD, subsequently, Ni/Graphene samples were dipped successively in PCL and cyclododecane (CDD) solutions prior to the removal of Ni from the 3D-GF/PCL scaffold in FeCl3. Our results showed that the electrical conductivity of the polymer composites reached to 25 S.m-1 after incorporation of 3D-GF. Moreover, the mechanical properties of 3D-GF/PCL composite scaffold were enhanced with respect to the same geometry of PCL scaffolds. The wettability, surface porosity, and morphology did not show any significant changes, while the PC12 cell proliferation and extension were increased for the developed 3D-GF/PCL nanocomposite. It can be concluded that 3D-GF/PCL nanocomposites could be good candidates to utilize as a versatile system for the engineering of peripheral nerve tissue.

Rational construction of porous N-doped Fe2O3 films on porous graphene foams by molecular layer deposition for tunable microwave absorption.

Graphene-based materials with porous microstructure have attracted immense attentions due to their wide application in microwave absorption. However, constructing magnetic film with both porous microstructure and uniform pore size by using traditional methods still remains a challenge. To overcome this problem, we reported a facile strategy of molecular layer deposition (MLD) for successfully fabrication of the hybrid-architecture of porous graphene foams and nitrogen-doped porous Fe2O3 films. The surfaces of porous graphene foams are uniformly covered by porous Fe2O3 films without aggregation and the pore structures are widely distributed. The porous graphene-based composites exhibit remarkably enhanced microwave absorption performance compared to the pristine graphene foams. The minimum reflection loss value is increased by approximately 8 times, reaching -64.36 dB with a thickness of only 2.18 mm. More importantly, the absorption property can be precisely modulated by tuning the MLD cycle numbers and effective absorption bandwidth covers 3.04-18.0 GHz by adjusting the thickness from 1.0 to 5.0 mm. This work provides new insights for exploring novel and high-performance graphene-based microwave absorbents and offers a new idea to rationally design three-dimensional composites with porous magnetic films.

Applications of three-dimensional graphenes for preconcentration, extraction, and sorption of chemical species: a review.

This review (with 115 refs) summarizes applications of 3-dimensional graphene (3DGs) and its derivatives in the fields of preconcentration, extraction, and sorption. Following an introduction into the field (including a definition of the materials treated here), the properties and synthetic strategies for 3DGs are described. The next section covers applications of 3DG-based adsorbents in solid phase extraction of organic species including drugs, phthalate esters, chlorophenols, aflatoxins, insecticides, and pesticides. Another section treats applications of 3DGs in solid phase microextraction of species such as polycyclic aromatic hydrocarbons, alcohols, and pesticides. We also describe how the efficiency of assays may be improved by using these materials as a sorbent. A final section covers conclusions and perspectives. Graphical abstract Graphical abstract contains poor quality and small text inside the artwork. Please do not re-use the file that we have rejected or attempt to increase its resolution and re-save. It is originally poor, therefore, increasing the resolution will not solve the quality problem. We suggest that you provide us the original format. We prefer replacement figures containing vector/editable objects rather than embedded images. Preferred file formats are eps, ai, tiff and pdf.Tiff file of graphical abstract was attached. Schematic presentation of synthesis of three-dimensional graphene (3DG) from two-dimensional graphene (2DG) with self-assembly, template-assisted and direct deposition methods. Application of 3DG-based nanoadsorbents in direct immersion-solid phase microextraction (DI-SPME), headspace-SPME (HS-SPME), magnetic-solid phase extraction (Magnetic-SPE), dispersive-SPE, and magnetic sheet-SPE.

Three-Dimensional Graphene Foams: Synthesis, Properties, Biocompatibility, Biodegradability, and Applications in Tissue Engineering.

Presently, clinical nanomedicine and nanobiotechnology have impressively demanded the generation of new organic/inorganic analogues of graphene (as one of the intriguing biomedical research targets) for stem-cell-based tissue engineering. Among different shapes of graphene, three-dimensional (3D) graphene foams (GFs) are highly promising candidates to provide conditions for mimicking in vivo environments, affording effective cell attachment, proliferation,and differentiation due to their unique properties. These include the highest biocompatibility among nanostructures, high surface-to-volume ratio, 3D porous structure (to provide a homogeneous/isotropic growth of tissues), highly favorable mechanical characteristics, and rapid mass and electron transport kinetics (which are required for chemical/physical stimulation of differentiated cells). This review aims to describe recent and rapid advances in the fabrication of 3D GFs, together with their use in tissue engineering and regenerative nanomedicine applications. Moreover, we have summarized a broad range of recent studies about the behaviors, biocompatibility/toxicity,and biodegradability of these materials, both in vitro and in vivo. Finally, the highlights and challenges of these 3D porous structures, compared to the current polymeric scaffold competitors, are discussed.

A Fast Response-Recovery 3D Graphene Foam Humidity Sensor for User Interaction.

Humidity sensors allow electronic devices to convert the water content in the environment into electronical signals by utilizing material properties and transduction techniques. Three-dimensional graphene foam (3DGF) can be exploited in humidity sensors due to its convenient features including low-mass density, large specific surface area, and excellent electrical. In this paper, 3DGF with super permeability to water enables humidity sensors to exhibit a broad relative humidities (RH) range, from 0% to 85.9%, with a fast response speed (response time: ~89 ms, recovery time: ~189 ms). To interpret the physical mechanism behind this, we constructed a 3DGF model decorated with water to calculate the energy structure and we carried out the CASTEP as implemented in Materials Studio 8.0. This can be ascribed to the donor effect, namely, the electronic donation of chemically adsorbed water molecules to the 3DGF surface. Furthermore, this device can be used for user interaction (UI) with unprecedented performance. These high performances support 3DGF as a promising material for humidity sensitive material.

A Broadband Phototransistor Based on Three-Dimensional Reduced Graphene Oxide Foam.

Three-dimensional (3D) cross-linked polymer-like reduced graphene oxide foams (rGOFs) with a seamlessly continuous graphene network, exhibit high photoresponsive and conductivity and have received much attention regarding solar cells and supercapacitors. However, little attention has been paid to photodetection applications of 3D rGOFs. Here we report a novel broadband phototransistor based on metal-3D GFs-metal, which exhibits a high light absorption and a wide spectra response ranging at least from 400 to 1600 nm wavelength with a maximum photoresponsivity of 10 mA/W at 400 nm. In particular, stable and reproducible photocurrent cycles are achieved under different light blue light (405 nm), green light (532 nm), and NIR (808 nm) irradiations. Moreover, the device displays a typical transistor characteristic with a rapid response time of 18 ms at under 532 nm irradiation. The excellent performances indicate 3D rGOF as a promising candidate for future photodetection application.

Conductivity Maximum in 3D Graphene Foams.

In conventional foams, electrical properties often play a secondary role. However, this scenario becomes different for 3D graphene foams (GrFs). In fact, one of the motivations for synthesizing 3D GrFs is to inherit the remarkable electrical properties of individual graphene sheets. Despite immense experimental efforts to study and improve the electrical properties of 3D GrFs, lack of theoretical studies and understanding limits further progress. The causes to this embarrassing situation are identified as the multiple freedoms introduced by graphene sheets and multiscale nature of this problem. In this article, combined with transport modeling and coarse-grained molecular dynamic (MD) simulations, a theoretical framework is established to systematically study the electrical conducting properties of 3D GrFs with or without deformation. In particular, through large-scale and massive calculations, a general relation between contact area and conductance for two van der Waals bonded graphene sheets is demonstrated, in terms of which the conductivity maximum phenomenon in GrFs is first theoretically proposed and its competition mechanism is explained. Moreover, the theoretical prediction is consistent with previous experimental observations.

Multiscale Mechanics of Triply Periodic Minimal Surfaces of Three-Dimensional Graphene Foams.

The mechanics of triply periodic minimal surfaces (TPMSs) with three-dimensional (3D) graphene foams are systematically studied to understand the effects of structure and size on the mechanical properties, for example, elasticity, strength, and fracture. The design of lightweight open-shell porous solid materials with TPMSs has shown excellent and tunable load-bearing properties. However, fracture properties and their relations with surface topologies are largely unknown. Utilizing reactive molecular dynamics simulations, here we investigate the elastic and fracture properties of three different surface topologies with 3D graphene foams: P (primitive), D (diamond), and G (gyroid), called Schwarzites. Models with different lattice sizes are utilized to derive power laws, which can connect the properties along different sizes to shed light on the multiscale mechanics of TPMSs. Our study provides a systematic understanding of the relation between TPMS topologies and their mechanical properties, including failure mechanisms of graphene foams, opening opportunities to explore designable structures with tailored properties.

Vertically Aligned High-Quality Graphene Foams for Anisotropically Conductive Polymer Composites with Ultrahigh Through-Plane Thermal Conductivities.

Although graphene-based thermal interface materials (TIMs) have great potentials in removing excess heat generated during highly efficient running of electronic devices, their practical applications are usually limited by their unsatisfactory thermal conductions, which are mainly caused by unsatisfactory dispersion and distribution, low loading, and low quality of graphene sheets, as well as the thermal interfacial resistance between graphene sheets and polymer matrix. Herein, we develop vertically aligned graphene hybrid foams (GHFs) with high densities by hydrothermal reduction of graphene oxide in the presence of high-quality graphene nanoplatelets (GNPs) followed by air-drying. The reduced graphene oxide sheets play an important role in constructing a vertically aligned interconnection network for accommodating GNPs during the hydrothermal reduction process, while the incorporated GNPs not only make the thermal conductance network denser but also prevent excessive shrinkage of the foams during air-drying. More critically, graphitization of GHF at 2800 °C removes the residual oxygen-containing groups and heals the defects of their reduced graphene oxide component, leading to high-quality graphene foams. The resultant vertically aligned high-quality graphene porous architecture with high density as an ideal thermal conductance network of TIMs is highly efficient in improving the thermal conductivity of its epoxy composite, which exhibits an ultrahigh through-plane thermal conductivity of 35.5 W m-1 K-1 at a graphene loading of 19.0 vol %. The excellent thermally conductive performance makes the annealed GHF/epoxy composites suitable for the thermal management.

Laminated Object Manufacturing of 3D-Printed Laser-Induced Graphene Foams.

Laser-induced graphene (LIG), a graphene structure synthesized by a one-step process through laser treatment of commercial polyimide (PI) film in an ambient atmosphere, has been shown to be a versatile material in applications ranging from energy storage to water treatment. However, the process as developed produces only a 2D product on the PI substrate. Here, a 3D LIG foam printing process is developed on the basis of laminated object manufacturing, a widely used additive-manufacturing technique. A subtractive laser-milling process to yield further refinements to the 3D structures is also developed and shown here. By combining both techniques, various 3D graphene objects are printed. The LIG foams show good electrical conductivity and mechanical strength, as well as viability in various energy storage and flexible electronic sensor applications.

Nitrogen-Superdoped 3D Graphene Networks for High-Performance Supercapacitors.

An N-superdoped 3D graphene network structure with an N-doping level up to 15.8 at% for high-performance supercapacitor is designed and synthesized, in which the graphene foam with high conductivity acts as skeleton and nested with N-superdoped reduced graphene oxide arogels. This material shows a highly conductive interconnected 3D porous structure (3.33 S cm-1 ), large surface area (583 m2 g-1 ), low internal resistance (0.4 Ω), good wettability, and a great number of active sites. Because of the multiple synergistic effects of these features, the supercapacitors based on this material show a remarkably excellent electrochemical behavior with a high specific capacitance (of up to 380, 332, and 245 F g-1 in alkaline, acidic, and neutral electrolytes measured in three-electrode configuration, respectively, 297 F g-1 in alkaline electrolytes measured in two-electrode configuration), good rate capability, excellent cycling stability (93.5% retention after 4600 cycles), and low internal resistance (0.4 Ω), resulting in high power density with proper high energy density.

Harnessing Three Dimensional Anatomy of Graphene Foam to Induce Superior Damping in Hierarchical Polyimide Nanostructures.

Graphene foam-based hierarchical polyimide composites with nanoengineered interface are fabricated in this study. Damping behavior of graphene foam is probed for the first time. Multiscale mechanisms contribute to highly impressive damping in graphene foam. Rippling, spring-like interlayer van der Waals interactions and flexing of graphene foam branches are believed to be responsible for damping at the intrinsic, interlayer and anatomical scales, respectively. Merely 1.5 wt% graphene foam addition to the polyimide matrix leads to as high as ≈300% improvement in loss tangent. Graphene nanoplatelets are employed to improve polymer-foam interfacial adhesion by arresting polymer shrinkage during imidization and π-π interactions between nanoplatelets and foam walls. As a result, damping behavior is further improved due to effective stress transfer from the polymer matrix to the foam. Thermo-oxidative stability of these nanocomposites is investigated by exposing the specimens to glass transition temperature of the polyimide (≈400 °C). The composites are found to retain their damping characteristics even after being subjected to such extreme temperature, attesting their suitability in high temperature structural applications. Their unique hierarchical nanostructure provides colossal opportunity to engineer and program material properties.

New strategy to rescue the inhibition of osteogenesis of human bone marrow-derived mesenchymal stem cells under oxidative stress: combination of vitamin C and graphene foams.

To rescue the oxidative stress induced inhibition of osteogenesis, vitamin C (VC) was chemically modified onto three-dimensional graphene foams (3D GFs), then their regulation on osteogenesis of human bone marrow-derived mesenchymal stem cells (BM-MSCs) was studied. Combined action of VC + GF significantly decreased H2O2-induced oxidative stress, and rescued H2O2-inhibited cell viability, differentiation and osteogenesis of BM-MSCs in vitro. Further studies revealed that Wnt pathway may be involved in this protection of osteogenesis. Furthermore, an in vivo mouse model of BM-MSCs transplantation showed that VC + GF remarkably rescued oxidative stress inhibited calcium content and bone formation. The combination of VC and GF exhibited more pronounced protective effects against oxidative stress induced inhibition of osteogenesis, compared to monotherapy of VC or GF. Our study proposed a new strategy in stem cell-based therapies for treating bone diseases.

Bacteria-Affinity 3D Macroporous Graphene/MWCNTs/Fe3O4 Foams for High-Performance Microbial Fuel Cells.

Promoting the performance of microbial fuel cells (MFCs) relies heavily on the structure design and composition tailoring of electrode materials. In this work, three-dimensional (3D) macroporous graphene foams incorporated with intercalated spacer of multiwalled carbon nanotubes (MWCNTs) and bacterial anchor of Fe3O4 nanospheres (named as G/MWCNTs/Fe3O4 foams) were first synthesized and used as anodes for Shewanella-inoculated microbial fuel cells (MFCs). Thanks to the macroporous structure of 3D graphene foams, the expanded electrode surface by MWCNTs spacing, as well as the high affinity of Fe3O4 nanospheres toward Shewanella oneidensis MR-1, the anode exhibited high bacterial loading capability. In addition to spacing graphene nanosheets for accommodating bacterial cells, MWCNTs paved a smoother way for electron transport in the electrode substrate of MFCs. Meanwhile, the embedded bioaffinity Fe3O4 nanospheres capable of preserving the bacterial metabolic activity provided guarantee for the long-term durability of the MFCs. With these merits, the constructed MFC possessed significantly higher power output and stronger stability than that with conventional graphite rod anode.

Solution-Processed Ultraelastic and Strong Air-Bubbled Graphene Foams.

Solution-processed ultraelastic graphene foams are prepared via a convenient air-bubble-promoted synthesis. These foams can dissipate external compression through the ordered interconnecting graphene network between the bubbles without causing a local fracture and thus reliably show compressive stress of 5.4 MPa at a very high strain of 99%, setting a new benchmark for solution-processed graphene foams.

A Phytic Acid Induced Super-Amphiphilic Multifunctional 3D Graphene-Based Foam.

Surfaces with super-amphiphilicity have attracted tremendous interest for fundamental and applied research owing to their special affinity to both oil and water. It is generally believed that 3D graphenes are monoliths with strongly hydrophobic surfaces. Herein, we demonstrate the preparation of a 3D super-amphiphilic (that is, highly hydrophilic and oleophilic) graphene-based assembly in a single-step using phytic acid acting as both a gelator and as a dopant. The product shows both hydrophilic and oleophilic intelligence, and this overcomes the drawbacks of presently known hydrophobic 3D graphene assemblies. It can absorb water and oils alike. The utility of the new material was demonstrated by designing a heterogeneous catalytic system through incorporation of a zeolite into its amphiphilic 3D scaffold. The resulting bulk network was shown to enable efficient epoxidation of alkenes without prior addition of a co-solvent or stirring. This catalyst also can be recovered and re-used, thereby providing a clean catalytic process with simplified work-up.

Base-Induced Liquid Crystals of Graphene Oxide for Preparing Elastic Graphene Foams with Long-Range Ordered Microstructures.

Base-induced graphene oxide (GO) liquid crystals form a highly ordered texture. This microstructure can be inherited by graphene foams prepared by hydrothermal reduction, showing a long-range ordered microstructure of graphene sheets in 3D. This provides an insightful understanding into the supramolecular chemistry of GO sheets.

3D Graphene-Foam-Reduced-Graphene-Oxide Hybrid Nested Hierarchical Networks for High-Performance Li-S Batteries.

A 3D graphene-foam-reduced-graphene-oxide hybrid nested hierarchical network is synthesized to achieve high sulfur loading and content simultaneously, which solves the "double low" issues of Li-S batteries. The obtained Li-S cathodes show a high areal capacity two times larger than that of commercial lithium-ion batteries, and a good cycling performance comparable to those at low sulfur loading.

A Robust and Cost-Effective Superhydrophobic Graphene Foam for Efficient Oil and Organic Solvent Recovery.

Water pollution caused by chemical reagent leaking, industrial wastewater discharging, and crude oil spills has raised global concerns on environmental sustainability, calling for high-performance absorbent materials for effective treatments. However, low-cost materials capable of effectively separating oils and organic solvents from water with a high adsorption capacity and good recyclability are rare on the market. Here, a cost-effective method is reported to fabricate high-performance graphene modified absorbents through the facile thermal reduction of graphene oxide on the skeletons of melamine foam. By integrating the high porosity, superior elasticity, and mechanical stability of raw sponge with the chemical stability and hydrophobicity of graphene sheets, the as-fabricated graphene foam not only possesses a rough and superhydrophobic surface, but also exhibits an excellent adsorption performance and extraordinary recyclability for various oils and organic solvents. It is worth mentioning that the superhydrophobic surface also endows the graphene foam with an excellent efficiency for oil/water separation. More importantly, the cost-effective fabrication method without involving expensive raw materials and sophisticated equipment permits a scale-up of the graphene foam for pollution disposal. All these features make the graphene foam an ideal candidate for removal and collection of oils and organic solvents from water.