ABSTRACT
Few-atom metal clusters (FAMCs) exhibit superior performance in catalyzing complex molecular transformations due to their special spatial environments and electronic states, compared to single-atom catalysts (SACs). However, achieving the efficient and accurate synthesis of FAMCs while avoiding the formation of other species, such as nanoparticles and SACs, still remains challenges. Herein, we report a two-step strategy for synthesis of few-atom platinum (Pt) clusters by predeposition of zinc single-atom-glue (Zn1) on MgO nanosheets (Ptn-Zn1/MgO), where FAMCs can be obtained over a wide range of Pt contents (0.09 to 1.45â wt %). Zn atoms can act as Lewis acidic sites to allow electron transfer between Zn and Pt through bridging O atoms, which play a crucial role in the formation and stabilization of few-atom Pt clusters. Ptn-Zn1/MgO exhibited a high selectivity of 93 % for anti-Markovnikov alkene hydrosilylation. Moreover, an excellent activity with a turnover frequency of up to 1.6×104â h-1 can be achieved, exceeding most of the reported Pt SACs. Further theoretical studies revealed that the Pt atoms in Ptn-Zn1/MgO possess moderate steric hindrance, which enables high selectivity and activity for hydrosilylation. This work presents some guidelines for utilizing atomic-scale species to increase the synthesis efficiency and precision of FAMCs.
ABSTRACT
Vapor-based deposition techniques are emerging approaches for the design of carbon-supported metal powder electrocatalysts with tailored catalyst entities, sizes, and dispersions. Herein, a pulsed CVD (Pt-pCVD) approach is employed to deposit different Pt entities on mesoporous N-doped carbon (MPNC) nanospheres to design high-performance hydrogen evolution reaction (HER) electrocatalysts. The influence of consecutive precursor pulse number (50-250) and deposition temperature (225-300 °C) are investigated. The Pt-pCVD process results in highly dispersed ultrasmall Pt clusters (≈1 nm in size) and Pt single atoms, while under certain conditions few larger Pt nanoparticles are formed. The best MPNC-Pt-pCVD electrocatalyst prepared in this work (250 pulses, 250 °C) reveals a Pt HER mass activity of 22.2 ± 1.2 A mg-1 Pt at -50 mV versus the reversible hydrogen electrode (RHE), thereby outperforming a commercially available Pt/C electrocatalyst by 40% as a result of the increased Pt utilization. Remarkably, after optimization of the Pt electrode loading, an ultrahigh Pt mass activity of 56 ± 2 A mg-1 Pt at -50 mV versus RHE is found, which is among the highest Pt mass activities of Pt single atom and cluster-based electrocatalysts reported so far.
ABSTRACT
As cost-effective catalysts, platinum (Pt) single-atom catalysts (SACs) have attracted substantial attention. However, most studies indicate that Pt SACs in acidic hydrogen evolution reaction (HER) follow the slow Volmer-Heyrovsky (VH) mechanism instead of the fast kinetic Volmer-Tafel (VT) pathway. Here, this work propose that the VH mechanism in Pt SACs can be switched to the faster VT pathway for efficient HER by correlating Pt single atoms (SAs) with Pt clusters (Cs). Our calculations reveal that the correlation between Pt SAs and Cs significantly impacts the electronic structure of exposed Pt atoms, lowering the adsorption barrier for atomic hydrogen and enabling a faster VT mechanism. To validate these findings, this work purposely synthesize three catalysts: l-Pt@MoS2, m-Pt@MoS2 and h-Pt@MoS2 with low, moderate, and high Pt-loading, having different distributions of Pt SAs and Cs. The m-Pt@MoS2 catalyst with properly correlating Pt SAs and Cs exhibits outstanding performance with an overpotential of 47 mV and Tafel slope of 32 mV dec-1. Further analysis of the Tafel values confirms that the m-Pt@MoS2 sample indeed follows the VT reaction mechanism, aligning with the theoretical findings. This study offers a deep understanding of the synergistic mechanism, paving a way for designing novel-advanced catalysts.
ABSTRACT
The hydrogen evolution reaction (HER) activity of defect-stabilized low-Pt-loading catalysts is closely related with defect type in support materials, while the knowledge about the effect of higher-dimensional defects on the property and activity of trapped Pt atomic species is scarce. Herein, small size (5-10 nm) TiO2 nanoparticles with abundant surface step defects (one kind of line defect) are used to direct the uniform anchoring of Pt atomic clusters (Pt-ACs) via PtâOâTi linkage. The as-made low-Pt catalysts (Pt-ACs/S-TiO2 -NP) exhibit exceptional HER intrinsic activity due to the unique step-site Pi-O-Ti species, in which the mass activity and turnover frequency are as high as 21.46 A mg Pt -1 and 21.69 s-1 at the overpotential of 50 mV, both far beyond those of benchmark Pt/C catalysts and other Pt-ACs/TiO2 samples with less step sites. Spectroscopic measurements and theoretical calculations reveal that the step-defect-located PtâOâTi sites can simultaneously induce the charge transfer from TiO2 substrate to the trapped Pt-ACs and the downshift of d-band center, which helps the proton reduction to H* intermediates and the following hydrogen desorption process, thus improving the HER. The work provides a deep insight on the interactions between high-dimensional defect and well-dispersed atomic metal motifs for superior HER catalysis.
ABSTRACT
Fuel cells are considered potential energy conversion devices for utopia; nevertheless, finding a highly efficacious and economical electrocatalyst for the oxygen reduction reaction (ORR) is of great interest. By keeping this in view, we have proposed a novel design of a trimetallic nanocatalyst (NC) comprising atomic Pt clusters at the heterogeneous Ni(OH)2-to-Pd interface (denoted NPP-70). The as-prepared material surpasses the commercial J.M.-Pt/C (20 wt %) catalyst by â¼ 166 and â¼19 times with exceptionally high specific and mass activities of 16.11 mA cm-2 and 484.8 mA mgPt-1 at 0.90 V versus reversible hydrogen electrode (RHE) in alkaline ORR (0.1 M KOH), respectively. On top of that, NPP-70 NC retains nearly 100% performance after 10k accelerated durability test (ADT) cycles. The results of physical characterization and electrochemical analysis confirm that atomic-scale Pt clusters induce strong lattice strain (compressive) at the Ni(OH)2-to-Pd interface, which triggers the electron relocation from Ni to Pt atoms. Such charge localization is vital for O2 splitting on surface Pt atoms, followed by the relocation of OH- ions from the Pd surface. Besides, a sharp fall down in ORR performance (mass activity is 37 mA mgPt-1 at 0.90 V versus RHE) is observed when the Pt clusters are decorated on the surface of NiOx and Pd (denoted NPP-RT). In situ partial fluorescence yield mode X-ray absorption spectroscopy (PFY-XAS) was employed to reveal the ORR pathways on both configurations. The obtained results demonstrate that interface engineering can be a potential approach to boost the electrocatalytic activity of metal hydroxide/oxide-supported Pd nanoparticles and in turn allow Pd to be a promising alternative for commercial Pt catalysts.
ABSTRACT
Platinum is one of the best-performing catalysts for the hydrogen evolution reaction (HER). However, high cost and scarcity severely hinder the large-scale application of Pt electrocatalysts. Constructing highly dispersed ultrasmall Platinum entities is thereby a very effective strategy to increase Pt utilization and mass activities, and reduce costs. Herein, highly dispersed Pt entities composed of a mixture of Pt single atoms, clusters, and nanoparticles are synthesized on mesoporous N-doped carbon nanospheres. The presence of Pt single atoms, clusters, and nanoparticles is demonstrated by combining among others aberration-corrected annular dark-field scanning transmission electron microscopy, X-ray absorption spectroscopy, and electrochemical CO stripping. The best catalyst exhibits excellent geometric and Pt HER mass activity, respectively ≈4 and 26 times higher than that of a commercial Pt/C reference and a Pt catalyst supported on nonporous N-doped carbon nanofibers with similar Pt loadings. Noteworthily, after optimization of the geometrical Pt electrode loading, the best catalyst exhibits ultrahigh Pt and catalyst mass activities (56 ± 3 A mg-1 Pt and 11.7 ± 0.6 A mg-1 Cat at -50 mV vs. reversible hydrogen electrode), which are respectively ≈1.5 and 58 times higher than the highest Pt and catalyst mass activities for Pt single-atom and cluster-based catalysts reported so far.
ABSTRACT
The size effect on nanoparticles, which affects the catalysis performance in a significant way, is crucial. The tuning of oxygen vacancies on metal-oxide support can help reduce the size of the particles in active clusters of Pt, thus improving catalysis performance of the supported catalyst. Herein, Ce-Sn solid solutions (CSO) with abundant oxygen vacancies have been synthesized. Activated by simple CO reduction after loading Pt species, the catalytic CO oxidation performance of Pt/CSO was significantly better than that of Pt/CeO2 . The reasons for the elevated activity were further explored regarding ionic Pt single sites being transformed into active Pt clusters after CO reduction. Due to more exposed oxygen vacancies, much smaller Pt clusters were created on CSO (ca. 1.2â nm) than on CeO2 (ca. 1.8â nm). Consequently, more exposed active Pt clusters significantly improved the ability to activate oxygen and directly translated to the higher catalytic oxidation performance of activated Pt/CSO catalysts in vehicle emission control applications.
ABSTRACT
Water-gas shift (WGS) reaction at low temperature plays an important role in hydrogen production from fossil fuels and hydrogen purification for proton-exchange membrane fuel cells. However, the activation of H2 O is a critical reaction step that greatly limits the overall performance during WGS reaction. Here we fabricate porous single-crystalline (PSC) MoO3 monoliths at 1â cm scale and deposit atomic-layered Pt clusters at the lattice surface to create the interfacial system toward the low-temperature WGS reaction. The single-crystalline nature stabilizes the oxygen vacancies (VO ) at lattice and facilitates the effective activation of H2 O at the interface. We show the highest Pt-normalized activity of 0.86â molCO molPt -1 s-1 for the ultra-low temperature WGS reaction at 120 °C. The single-crystalline features with enhanced fluxion in porous architectures lead to outstanding performance without visible degradation even after continuous operation for 100â hours.
ABSTRACT
Cellulose grains were carbonized and applied as catalyst supports for nickel- and magnetite-promoted bimetallic palladium- and platinum-containing catalysts. The bimetallic spherical aggregates of Pd and Pt particles were created to enhance the synergistic effect among the precious metals during catalytic processes. As a first step, the cellulose bead-based supports were impregnated by nitrate salts of nickel and iron and carbonized at 973 K. After this step, the nickel was in an elemental state, while the iron was in a magnetite form in the corresponding supports. Then, Pd and Pt particles were deposited onto the supports and the catalyst surface; precious metal nanoparticles (10-20 nm) were clustered inside spherical aggregated particles 500-600 nm in size. The final bimetallic catalysts (i.e., Pd-Pt/CCB, Pd-Pt/Ni-CCB, and Pd-Pt/Fe3O4-CCB) were tested in hydrogenation of chlorate ions in the aqueous phase. For the nickel-promoted Pd-Pt catalyst, a >99% chlorate conversion was reached after 45 min at 80 °C. In contrast, the magnetite-promoted sample reached an 84.6% chlorate conversion after 3 h. Reuse tests were also carried out with the catalysts, and in the case of Pd-Pt/Ni-CCB after five cycles, the catalytic activity only decreased by ~7% which proves the stability of the system.
Subject(s)
Cellulose/chemistry , Chlorates/chemistry , Ferrosoferric Oxide/chemistry , Hydrogen/chemistry , Metal Nanoparticles/chemistry , Palladium/chemistry , Platinum/chemistry , Catalysis , Water/chemistryABSTRACT
Subnanometric metal clusters have attracted extensive attention because of their unique properties as heterogeneous catalysts. However, it is challenging to obtain uniformly distributed metal clusters under synthesis and reaction conditions. Herein, we report a template-guidance protocol to synthesize subnanometric metal clusters uniformly encapsulated in beta-zeolite, with the metal ions anchored to the internal channels of the zeolite template via electrostatic interactions. Pt metal clusters with a narrow size range of 0.89 to 1.22â nm have been obtained on the intersectional sites of beta-zeolite (Pt@beta) with a broad range of Si/Al molar ratios (15-200). The uniformly distributed Pt clusters in Pt@H-beta are subject to strong electron withdrawal by the zeolite, which promotes transfer of active hydrogen, providing excellent activity and stability in hydrodeoxygenation reactions. A general strategy is thus proposed for the encapsulation of subnanometric metal clusters in zeolites with high thermal stability.
ABSTRACT
The rational synthesis of single-layer noble metal directly anchored on support materials is an elusive target to accomplish for a long time. This paper reports well-defined single-layer Pt (Pt-SL) clusters anchored on ultrathin TiO2 nanosheets-as a new frontier in electrocatalysis. The structural evolution of Pt-SL/TiO2 via self-assembly of single Pt atoms (Pt-SA) is systematically recorded. Significantly, the Pt atoms of Pt-SL/TiO2 possess a unique electronic configuration with PtPt covalent bonds surrounded by abundant unpaired electrons. This Pt-SL/TiO2 catalyst presents enhanced electrochemical performance toward diverse electrocatalytic reactions (such as the hydrogen evolution reaction and the oxygen reduction reaction) compared with Pt-SA, multilayer Pt nanoclusters, and Pt nanoparticles, suggesting an efficient new type of catalyst that can be achieved by constructing single-layer atomic clusters on supports.
ABSTRACT
The unaffordable costs of the automotive proton exchange membrane fuel cell (PEMFC), remaining a roadblock for commercial applications as an alternative to combustion engine vehicles, can be overcome partially by remarkably increasing the utilization of irreplaceable platinum (Pt). Herein, atomically precise Pt with scalable atoms ranging from 1 to 43 atoms, stabilized by a homemade carbon from white radish without any ligands, is prepared by a repeated UV irradiation method that is industrially scalable. Compared with the isolated Pt1 in the form of Pt-N4, octahedral Pt6, and icosahedron Pt13, the ordered Pt43 cluster (â¼0.75 nm) with higher metal coordination number displays much higher oxygen reduction reaction performance with a mass activity, which is about 1036% higher than that obtained by state-of-the-art Pt/C, an increase by a factor of â¼3.3 as compared with the DOE 2020 target (0.44 A mgPt-1). The utilization rate of Pt atoms reaches up to 94.7%, much higher than that of Pt (2 nm, 56%), capable of further reducing the amount of platinum that is required for PEMFCs. Moreover, the cluster exhibits an outstanding stability due to the improved Pt vacancy formation energy raised by stronger atom interaction in the close-packed cluster. The cluster exhibits a unique finite size effect from self-tuned energy band and strain levels. A clear strain effect on the d-band center is first presented for pure Pt without distortion from ligands like a second metal. Therefore, the assembly of subnanometer Pt with atom alteration opens up new horizons in designing efficient platinum group metal (PGM) catalysts by reducing the size to subnanometer scale.
ABSTRACT
Single-atom catalysts (SAs) with the maximum atom utilization and breakthrough activities toward hydrogen evolution reaction (HER) have attracted considerable research interests. Uncovering the nature of single-atom metal centers under operating electrochemical condition is highly significant for improving their catalytic performance, yet is poorly understood in most studies. Herein, Pt single atoms anchoring on the nitrogen-carbon substrate (PtSA /N-C) as a model system are utilized to investigate the dynamic structure of Pt single-atom centers during the HER process. Via in situ/operando synchrotron X-ray absorption spectroscopy and X-ray photoelectron spectroscopy, an intriguing structural reconstruction at atomic level is identified in the PtSA /N-C when it is subjected to the repetitive linear sweep voltammetry and cyclic voltammetry scanning. It demonstrates that the PtN bonding tends to be weakened under cathodic potentials, which induces some Pt single atoms to dynamically aggregate into forming small clusters during the HER reaction. More importantly, experimental evidence and/or indicator is offered to correlate the observed Tafel slope with the dynamic structure of Pt catalysts. This work provides an evident understanding of SAs under electrocatalytic process and offers informative insights into constructing efficient catalysts at atomic level for electrochemical water-splitting system.
ABSTRACT
Electrochemical water splitting is considered as a promising approach to produce clean and sustainable hydrogen fuel. As a new class of nanomaterials with high ratio of surface atoms and tunable composition and electronic structure, metal clusters are promising candidates as catalysts. Here, a new strategy is demonstrated to synthesize active and stable Pt-based electrocatalysts for hydrogen evolution by confining Pt clusters in hollow mesoporous carbon spheres (Pt5 /HMCS). Such a structure would effectively stabilize the Pt clusters during the ligand removal process, leading to remarkable electrocatalytic performance for hydrogen production in both acidic and alkaline solutions. Particularly, the optimal Pt5 /HMCS electrocatalyst exhibits 12 times the mass activity of Pt in commercial Pt/C catalyst with similar Pt loading. This study exemplifies a simple yet effective approach to improve the cost effectiveness of precious-metal-based catalysts with stabilized metal clusters.
ABSTRACT
As a highly oxygen-dependent process, the effect of photodynamic therapy is often obstructed by the premature leakage of photosensitizers and the lack of oxygen in hypoxic cancer cells. To overcome these limitations, this study designs bovine serum albumin protein (BSA)-encapsulated Pt nanoclusters (PtBSA) as O2-supplied biocoats and further incorporates them with mesoporous silica nanospheres to develop intelligent nanoaggregates for achieving improved therapeutic outcomes against hypoxic tumors. The large number of amino groups on BSA can provide sufficient functional groups to anchor tumor targeting agents and thus enhance the selective cellular uptake efficiency. Owing to the outstanding biocompatibility features of BSA and the state-of-the-art catalytic activity of Pt nanoclusters, the nanocomposites have lower dark cytotoxicity, and O2 continuously evolves via the decomposition of H2O2 in a tumor microenvironment. Both in vivo and in vitro experiments indicate that the resulting nanocomposites can effectively relieve hypoxic conditions, specifically induce necrotic cell apoptosis, and remarkably hinder tumor growth. Our results illuminate the great potential of BSA-encapsulated Pt nanoclusters as versatile biocoats in designing intelligent nanocarriers for hypoxic-resistant photodynamic therapy.
Subject(s)
Biocompatible Materials/pharmacology , Nanostructures/administration & dosage , Neoplasms/therapy , Photochemotherapy , A549 Cells , Animals , Apoptosis/drug effects , Biocompatible Materials/chemistry , Cell Proliferation/drug effects , Heterografts , Humans , Hydrogen Peroxide/chemistry , Hydrogen Peroxide/pharmacology , Mice , Nanocomposites/chemistry , Nanostructures/chemistry , Neoplasms/pathology , Oxygen/metabolism , Photosensitizing Agents/chemistry , Photosensitizing Agents/pharmacology , Serum Albumin, Bovine/chemistry , Serum Albumin, Bovine/pharmacology , Silicon Dioxide/chemistry , Silicon Dioxide/pharmacology , Tumor Hypoxia/drug effects , Tumor Microenvironment/drug effectsABSTRACT
The trinuclear platinum cluster [Pt3(µ-PBut2)3(CO)3]CF3SO3 (I) was designed featuring the presence of a nearly equilateral platinum triangle bridged by three di-tert-butylphosphide ligands; in addition, each platinum center bears a terminal carbonyl ligand. This triplatinum cluster was initially developed in view of applications in the field of cluster-containing innovative materials. Yet, due to the large success of platinum complexes in cancer treatment, we also decided to explore its cytotoxic and anticancer properties. Accordingly, the solubility profile of this compound in several solvents was preliminarily investigated, revealing a conspicuous solubility in DMSO and DMSO/buffer mixtures; this makes the biological testing of I amenable. UV-Vis measurements showed that the triplatinum cluster is stable for several hours under a variety of conditions, within aqueous environments. No measurable reactivity was observed for I toward two typical model proteins, i.e. lysozyme and cytochrome c. On the contrary, a significant reactivity was evidenced when reacting I with small sulfur-containing ligands. In particular, a pronounced reactivity with reduced glutathione and cysteine emerged from ESI-MS experiments, proving complete formation of I-GSH and I-Cys derivatives, with the loss of a single carbonyl ligand. Starting from these encouraging results, the cytotoxic potential of I was assayed in vitro against a panel of representative cancer cell lines, and potent cytotoxic properties were disclosed. Of particular interest is the finding that the triplatinum species manifests potent antiproliferative properties toward Triple Negative Breast Cancer Cells, often refractory to most anticancer drugs. Owing to the reported encouraging results, a more extensive biological and pharmacological evaluation of this Pt cluster is now warranted to better elucidate its mode of action.
Subject(s)
Antineoplastic Agents , Breast Neoplasms/drug therapy , Breast Neoplasms/metabolism , Organoplatinum Compounds , Antineoplastic Agents/chemical synthesis , Antineoplastic Agents/chemistry , Antineoplastic Agents/pharmacology , Breast Neoplasms/pathology , Drug Screening Assays, Antitumor , Female , HL-60 Cells , Humans , MCF-7 Cells , Organoplatinum Compounds/chemical synthesis , Organoplatinum Compounds/chemistry , Organoplatinum Compounds/pharmacologyABSTRACT
Highly monodispersed Cu-Pt bimetallic nanoclusters were synthesized by a facile synthesis approach. Analysis of transmission electron microscopy (TEM) and spherical aberration (C s)-corrected scanning transmission electron microscopy (STEM) images shows that the average diameter of the Cu-Pt nanoclusters is 3.0 ± 1.0 nm. The high angle annular dark field (HAADF-STEM) images, intensity profiles, and energy dispersive X-ray spectroscopy (EDX) line scans, allowed us to study the distribution of Cu and Pt with atomistic resolution, finding that Pt is embedded randomly in the Cu lattice. A novel simulation method is applied to study the growth mechanism, which shows the formation of alloy structures in good agreement with the experimental evidence. The findings give insight into the formation mechanism of the nanosized Cu-Pt bimetallic catalysts.