Redispersing Ir Nanoparticles via a Carbon-Assisted Pyrolysis Process to Break the Activity-Stability Trade-Off of H2 Sensors.

Oxide semiconductor-supported metal nanoparticles often suffer from a high-temperature gas sensing process, resulting in agglomeration and coalescence, which significantly decrease their surface activity and stability. Here, we develop an in situ pyrolysis strategy to redisperse commercial Ir particles (∼15.6 nm) into monodisperse Ir species (∼5.4 nm) on ZnO supports, exhibiting excellent sintering-resistant properties and H2 sensing. We find that large-size Ir nanoparticles can undergo an unexpected splitting decomposition process and spontaneously migrate along the encapsulated carbon layer surface during high-temperature pyrolysis of ZIF-8. This resultant monodisperse status can be integrally reserved, accompanying further oxidation sintering. The final Irred/ZnO-450-based sensor exhibits outstanding stability, H2 response (10-2000 ppm), fast response/recovery capability (7/9.7 s@100 ppm), and good moisture resistance. In situ Raman and ex situ XPS further experimentally verify that highly dispersive Ir species can promote the electron transfer process during the gas sensing process. Our strategy thus provides important insights into the design of agglomeration-resistant gas sensing materials for highly effective H2 detection.

Facile preparation of re-dispersible/amphoteric nanochitin powder via choline chloride/propanedioic composite for stabilizing Pickering emulsions.

Choline chloride (ChCl)/propanedioic acid (PA) based hydrated composites are synthesized for producing nanochitins from crab shell in this work. The yield of nanochitin remains higher than 75 %, even if the water content reaches 80 %. ChCl is found necessary for the successful nano-fibrillation of chitin. However, PA contributes more to the yield improvement of nanochitin. ChCl mediated PA hydrolysis leads to the successful grafting of carboxyl groups in nanochitins, contributing to its amphoteric dispersed nature. After salt-induced separation and freeze-drying treatment, dried nanochitin powder can be prepared and found to disperse well either in acidic or alkaline suspension, exhibiting efficient drying/redispersion performance. The well amphoteric and drying/redispersion nature both benefit the facile preparation of nanochitin-based Pickering emulsions. For Pickering emulsion prepared under different pH, creaming only appears under acidic conditions (pH 3) for which the creaming index reaches 10.56 % after 30 days of storage. No obvious de-emulsification can be observed under pH 7 and 10. The efficient amphoteric and drying/redispersion nature together with the simplified preparation process of nanochitins are believed to facilitate the processing and practical applications of nanochitin.

In Situ Visualization and Mechanistic Understandings on Facet-Dependent Atomic Redispersion of Platinum on CeO2.

Redispersion is an effective method for regeneration of sintered metal-supported catalysts. However, the ambiguous mechanistic understanding hinders the delicate controlling of active metals at the atomic level. Herein, the redispersion mechanism of atomically dispersed Pt on CeO2 is revealed and manipulated by in situ techniques combining well-designed model catalysts. Pt nanoparticles (NPs) sintered on CeO2 nano-octahedra under reduction and oxidation conditions, while redispersed on CeO2 nanocubes above ∼500 °C in an oxidizing atmosphere. The dynamic shrinkage and disappearance of Pt NPs on CeO2 (100) facets was directly visualized by in situ TEM. The generated atomically dispersed Pt with the square-planar [PtO4]2+ structure on CeO2 (100) facets was also confirmed by combining Cs-corrected STEM and spectroscopy techniques. The redispersion and atomic control were ascribed to the high mobility of PtO2 at high temperatures and its strong binding with square-planar O4 sites over CeO2 (100). These understandings are important for the regulation of atomically dispersed platinum catalysts.

Tackling the challenge of drying and redispersion of cellulose nanofibrils via membrane-facilitated liquid phase exchange.

It is generally acknowledged that to advance the application of cellulose nanofibrils (CNFs) in product formulations, challenges associated with the drying and redispersion of this material must be addressed. Despite increased research efforts in this area, these interventions still involve the use of additives or conventional drying technologies, which both have the capacity to drive up the cost of the final CNF powders. Herein, we prepared dried and redispersible CNF powders with varying surface functionalities without the use of additives nor conventional drying technologies. Rapid drying in air was achieved after liquid phase exchange from water to isopropyl alcohol. The surface properties, morphology and thermal stabilities were the same for the never-dried and redispersed forms. The rheological properties of the CNFs were also unaffected after drying and redispersion of unmodified and organic acid modified materials. However, for 2,2,6,6-tetramethylpiperidine 1-oxyl (TEMPO)-mediated oxidised CNFs with higher surface charge and longer fibrils, the storage modulus could not be recovered to the never-dried state because of the possible non-selective reduction in length upon redispersion. Nevertheless, this method provides an effective and low-cost process for the drying and redispersion of unmodified and surface modified CNFs.

Mixed-linkage (1,3;1,4)-ß-d-glucans as rehydration media for improved redispersion of dried cellulose nanofibrils.

Improving the redispersion and recycling of dried cellulose nanofibrils (CNFs) without compromising their nanoscopic dimensions and inherent mechanical properties are essential for their large-scale applications. Herein, mixed-linkage (1,3;1,4)-ß-d-glucan (MLG) was studied as a rehydration medium for the redispersion and recycling of dried CNFs, benefiting from the intrinsic affinity of MLG to both cellulose and water molecules as inspired from plant cell wall. MLG from barley with a lower molar ratio of cellotriosyl to cellotetraosyl units was found homogeneously coated on CNFs, facilitating rehydration of the network of individualized CNFs. The addition of barley MLG did not impair the mechanical properties of the CNF/MLG composites as compared to neat CNFs nanopaper. With the addition of 10 wt% barley MLG, dry CNF/MLG composite film was successfully redispersed in water and recycled with well-maintained mechanical properties, while lichenan from Icelandic moss, cationic starch, and xyloglucan could not help the redispersion of dried CNFs.

Redispersion Behavior of 2D MoS2 Nanosheets: Unique Dependence on the Intervention Timing of Natural Organic Matter.

The aggregation-redispersion behavior of nanomaterials determines their transport, transformation, and toxicity, which could be largely influenced by the ubiquitous natural organic matter (NOM). Nonetheless, the interaction mechanisms of two-dimensional (2D) MoS2 and NOM and the subsequent influences on the redispersion behavior are not well understood. Herein, we investigated the redispersion of single-layer MoS2 (SL-MoS2) nanosheets as influenced by Suwannee River NOM (SRNOM). It was found that SRNOM played a decisive role on the redispersion of MoS2 2D nanosheets that varied distinctly from the 3D nanoparticles. Compared to the poor redispersion of MoS2 aggregates in the absence or post-addition of SRNOM to the aggregates, co-occurrence of SRNOM in the dispersion could largely enhance the redispersion and mobility of MoS2 by intercalating into the nanosheets. Upon adsorption to SL-MoS2, SRNOM enhanced the hydration force and weakened the van der Waals forces between nanosheets, leading to the redispersion of the aggregates. The SRNOM fractions with higher molecular mass imparted better dispersity due to the preferable sorption of the large molecules onto SL-MoS2 surfaces. This comprehensive study advances current understanding on the transport and fate of nanomaterials in the water system and provides fresh insights into the interaction mechanisms between NOM and 2D nanomaterials.

Keys Unlocking Redispersion of Reactive PdOx Nanoclusters on Ce-Functionalized Perovskite Oxides for Methane Activation.

Nowadays, trace CH4 emitted from vehicle exhausts severely threaten the balance of the ecology system of our earth. Thereby, the development of active and stable catalysts capable of methane conversion under mild conditions is critical. Here, we present a convenient method to redisperse catalytically inert PdO nanoparticles (NPs) (>10 nm) into reactive PdOx nanoclusters (∼2 nm) anchored on a Ce-doped LaFeO3 parent. Isothermally activated in an N2 flow, the redispersed catalyst achieved a CH4 conversion of 90% at 400 °C, which is significantly higher than the fresh and H2- and O2-treated counterparts (625, 616, and 641 °C, respectively), indicating the importance of the gas atmosphere in the redispersion of PdO NPs. In addition, the comprehensive catalyst characterizations demonstrated that the isolated Ce ions in the perovskite lattice play an irreplaceable role in the redispersion of reactive sites and the reduction of the energy barrier for C-H scission. More importantly, the Ce additive helps to stabilize the PdOx species by reducing overoxidation, resulting in significant lifetime extension. Through a thorough understanding of structural manipulation, this study sheds light on the design of highly performing supported catalysts for methane oxidation.

Eco-friendly alkaline lignin/cellulose nanofiber drying system for efficient redispersion behavior.

Although nanocellulose is an eco-friendly, high-performance raw material provided by nature, the agglomeration of nanocellulose that occurs during the drying process is the biggest obstacle to its advanced materialization and commercialization. In this study, a facile and simple nanocellulose drying system was designed using lignin, which is self-assembled together with cellulose in natural wood, as an eco-friendly additive. The addition of lignin not only minimized aggregation during the drying and dehydration process of nanocellulose but also ensured excellent redispersion kinetics and stability. In addition, the added lignin could be removed through a simple washing process. Through FTIR, XRD, TGA, tensile and swelling tests, it was confirmed that the addition of lignin enabled the reversible restitution of the nanocellulose physicochemical properties to the level of pristine never-dried nanocellulose in drying, redispersion, and polymer processing processes.

MXene-Supported, Atomic-Layered Iridium Catalysts Created by Nanoparticle Re-Dispersion for Efficient Alkaline Hydrogen Evolution.

Tailoring the structure of metal components and interaction with their anchored substrates is essential for improving the catalytic performance of supported metal catalysts; the ideal catalytic configuration, especially down to the range of atomic layers, clusters, and even single atoms, remains a subject under intensive study. Here, an Ir-on-MXene (Mo2 TiC2 Tx ) catalyst with controlled morphology changing from nanoparticles down to flattened atomic layers, and finally ultrathin layers and single atoms dispersed on MXene nanosheets at elevated temperature, is presented. The intermediate structure, consisting of mostly Ir atomic layers, shows the highest activity toward the hydrogen evolution reaction (HER) under industry-compatible alkaline conditions. In addition, the better HER activity of Ir atomic layers than that of single atoms suggests that the former serves as the main active sites. Detailed mechanism analysis reveals that the nanoparticle re-dispersion process and Ir atomic layers with a moderate interaction to the substrate associate with unconventional electron transfer from MXene to Ir, leading to suitable H* adsorption. The results indicate that the structural design is important for the development of highly efficient catalysts.

Development of Fully Redispersible Dried Nanocrystals by Using Sucrose Laurate as Stabilizer for Increasing Surface Area and Dissolution Rate of Poorly Water-Soluble Drugs.

There is much interest in converting poorly water-soluble drugs into nanocrystals as they provide extremely high surface area that increases dissolution rate and oral bioavailability. However, nanocrystals are prepared as aqueous suspensions, and once the suspensions are dried for development of solid dosage forms, the nanocrystals agglomerate as large particles to reduce the excess surface energy. For successful development of drug products, it is essential that any agglomeration is reversible, and the dried nanocrystals regain original particle sizes after redispersion in aqueous media. We have established that sucrose laurate serves as a superb stabilizer to ensure complete redispersion of dried nanocrystals in aqueous media with mild agitation. Nanocrystals (150-300 nm) of three neutral drugs (fenofibrate, danazol and probucol) were produced with sucrose laurate by media milling, and suspensions were dried by tray drying under vacuum, spray drying, and lyophilization. Dried solids and their tablets redispersed into original particle sizes spontaneously. Preliminary studies showed that sucrose laurate can also redisperse acidic and basic drugs, indicating its versatile application. Fatty acid ester of another disaccharide, lactose laurate, also performed like sucrose laurate. Thus, we have developed a method of retaining high dissolution rate and, by implication, high bioavailability of nanocrystals from solid formulations.

A prospect of cost-effective handling and transportation of graphene oxides: folding and redispersion of graphene oxide microsheets.

Controlling the assembly of 2D materials such as graphene oxides (GO) has a significant impact on their properties and performance. One of the critical issues on the processing and handling of GO is that they need to be in dilution solution (0.5 to 2.5 wt%) to maintain their high degree of exfoliation and dispersion. As a result, the shipment of GO in large quantity involves a huge volume of solvent (water) and thus the transportation costs for large sales volume would become extremely high. Through cross-sectional scanning electron microscopy and polarized optical microscopy together with x-ray diffraction and small-angle x-ray scattering studies, we demonstrated that the assembly and structure of GO microsheets can be preserved without restacking, when assembled GO via water-based wet spinning are re-dispersed into solution. A couple of alkyl ammonium bromides, CTAB and TBAB, as well as NaOH, were examined as coagulants and the resulting fibers were redispersed in an aqueous solution. The redispersed solution of fibers that were wet-spun into the commonly used CTAB and TBAB coagulation baths, maintained their physico-chemical properties (similar to the original GO dispersion) however, did not reveal preservation of liquid crystallinity. Meanwhile, the redispersed fibers that were initially spun into NaOH coagulation bath were able to maintain their liquid crystallinity if the lateral size of the GO sheets was large. Based on these findings, a cost-effective solid handling approach is devised which involves (i) processing GO microsheets in solution into folded layers in solid-state, (ii) transporting assembled GO to the customers, and (iii) redispersion of folded GO into a solution for their use. The proposed solid handling of GO followed by redispersion into solution can greatly reduce the transportation costs of graphene oxide materials by reducing the transportation volume by more than 90%.

Comparison of Effects of Sodium Chloride and Potassium Chloride on Spray Drying and Redispersion of Cellulose Nanofibrils Suspension.

Cellulose nanofibrils (CNFs) were exposed to the same levels of potassium chloride (KCl) and sodium chloride (NaCl) before being subjected to spray drying. The effect of NaCl and KCl on the size of atomized droplets and the hydrogen bond retardation between CNFs was investigated by characterizing product morphology, particle size distribution, dispersion stability in aqueous system, and surface chemistry. The results showed that the CNF suspensions treated with KCl could be atomized into smaller droplets during spray drying, and then CNF powder with smaller sizes could be obtained. As the agglomeration was less, and the CNF with KCl addition had good dispersion stability after redispersion compared with CNF treated by NaCl. Therefore, KCl treatment was an effective method to reduce the agglomeration of CNF during spray drying.

Synthesis and conservation of cellulose nanocrystals.

This work deals with the preparation of cellulose nanocrystals (CNC) from microcrystalline cellulose by acid hydrolysis, discusses how their characteristics varied according to the drying technique used for their conservation and analyzes their re-dispersion in water. A stable water dispersion of "rod" or "needle" type CNC (≈5 nm of diameter, 276 nm of length and 41 mV of Z potencial) was initially prepared and then dried by lyophilization and spray. Thus powders with similar cristalinity but different morphology were obtained, while CNC seemed to aggregate in such an extent that hindered their re-dispersion in water. Only lyophilized CNC could be re-dispersed in water and maintained stable in dispersion for at least 24 h, when working with concentrations of CNC higher than a certain minimum value (3 %) and after submitting them to intense ultrasound treatments. The tested time achieved should be enough to allow their subsequent use in several applications.

Development of Universal Formulation with Superior Re-dispersion Using Nanocrystal Approach with Simultaneous Identification of API Physicochemical Properties.

Universal nanocrystal formulation which can be applied to water-insoluble compounds was proposed and the criteria of its physicochemical properties as an active pharmaceutical ingredients (API) were investigated. Nanocrystal suspension was prepared by a wet-beads milling method. An acceptable Critical Quality Attributes (CQA) of nanocrystal suspension was defined by Z-average less than 500 nm and Polydispersity index (PDI) less than 0.3. Screening studies of dispersing and wetting agents were conducted using three model compounds in different pKa, melting points, etc., to find universal nanocrystal formulation. The effect of four structurally different polymer species (hydroxypropyl cellulose (HPC), hydoroxypropyl methylcellulose (HPMC), polyvinylpyrrolidone (PVP) and polyvinyl alcohol (PVA)) and their different grades or five different surfactants (docusate sodium (DOSS), sodium lauryl sulfate (SLS), cetyl trimethyl ammonium bromide (CTAB), polysolbate80 (PS80), and polyoxyethylene castor oil (CO-35)) were studied on the re-dispersion stability. It was found that the combination of 4% (w/v) HPC-SSL and 0.2% (w/v) DOSS was the most robust nanocrystal formulation owing to Z-average less than 200 nm and good re-dispersion stability without aggregates at pH 1.2 and pH 6.8. API physicochemical properties were also identified using ten water-insoluble compounds. Consequently, it was found that solubility (water, pH 1.2 and pH 6.8), molecular weight, hydrogen bonding acceptor and the ratio of log D7.4 to C Log P were critical factors.

Can spray freeze-drying improve the re-dispersion of crystalline nanoparticles of pure naproxen?

Spray freeze drying (SFD) was used to prepare re-dispersible powders of crystalline, pure-drug nanodispersions of naproxen in lactose and stabilized with hydroxypropyl cellulose. The particle size of the rehydrated powders was determined using static light scattering/Mie analysis. The nanoparticles present in the SFD powders were aggregated but could be dispersed on re-dispersion with water and stirring either with or without additional ultrasonic treatment. The disaggregation of the SFD nanoparticles was superior to that reported in the literature for spray dried nanoparticles of the same composition. It appears that the moderately-rapid freezing of the large spray droplets in LN2 during SFD produces less aggregation than does evaporative drying of the much smaller droplets during spray drying. Re-dispersion was also found to depend strongly on the pH of the original nanodispersion. The solubility of this weak acid is greater at higher pH which resulted in formation of a dissolved fraction of drug in the nanodispersions during media milling. After SFD, the dissolved naproxen fraction formed an amorphous solid which re-dissolves on re-hydration whereas the crystalline nanoparticles disaggregate.

Effects of pH of processing-medium on re-dispersion of spray dried, crystalline nanoparticles of pure naproxen.

Crystalline nanodispersions of naproxen stabilized with hydroxypropyl cellulose were prepared at different pHs both below and above the pKa of the drug. After spray drying together with lactose, the measured particle size of the rehydrated dispersions using laser light scattering/Mie analysis was found to depend strongly on the pH of the original, processed nanodispersion. The pH-dependent solubility of this weak acid resulted in formation of a dissolved fraction of drug in the nanodispersions, this being higher as the pH increases. There was therefore a loss of crystalline naproxen during processing at higher pH, with fewer and/or smaller nanoparticles in the nanodispersion after nanomilling. After spray drying, the dissolved naproxen fraction formed an amorphous solid, as shown by differential scanning calorimetry and X-ray powder diffraction. The amorphous fraction re-dissolves on re-hydration. An improved disaggregation and smaller particle size of the nanoparticles at higher pH was observed because of the lower amount of crystalline nanoparticles now present. If the pH of the nanodispersion during processing is kept below the pKa for a weak acid, then a high yield of nanoparticles should be expected with little formation of an amorphous phase of the drug.

Salt-Induced Colloidal Destabilization, Separation, Drying, and Redispersion in Aqueous Phase of Cationic and Anionic Nanochitins.

This study is aimed at facilitating the use of ocean biomass for the isolation and use of derived nanostructures. Specifically, cationic and anionic nanochitins were produced from never-dried crab shells that underwent partial deacetylation (PD-NCh) or TEMPO-oxidization (TO-NCh). The effects of different electrolyte types (NaCl, CH3COONa, Na2CO3, CaCl2, AlCl3, and NH4Cl) were investigated with regards to fractionation (via colloidal destabilization and precipitation), drying, and ultimate redispersion of the nanochitins. Sodium carbonate was most effective in the case of PD-NCh processing, whereas no significant effect of salt type was noted for TO-NCh. The results are rationalized in terms of the dispersion stability that resulted from specific counterion adsorption and nanoparticle association as well as electrostatic-charge development at a given solution pH. These effects were used to limit hydrogen bonding and nonspecific interactions upon drying of the nanochitins. The weak interactions between nanochitin and monovalent Na+ and NH4+ explain the experimental observations. Aqueous dispersions reconstituted from dried PD-NCh and TO-NCh were colloidally stable and yielded highly viscous, gel-like nanochitin dispersions at mass concentrations as low as 1.5 and 3.0%, respectively. Our findings are expected to greatly facilitate green processing of nanochitin, an emerging type of biobased nanomaterial.

Bioavailability Enhancement of Poorly Water-Soluble Drugs via Nanocomposites: Formulation⁻Processing Aspects and Challenges.

Drug nanoparticles embedded in a dispersant matrix as a secondary phase, i.e., drug-laden nanocomposites, offer a versatile delivery platform for enhancing the dissolution rate and bioavailability of poorly water-soluble drugs. Drug nanoparticles are prepared by top-down, bottom-up, or combinative approaches in the form of nanosuspensions, which are subsequently dried to prepare drug-laden nanocomposites. In this comprehensive review paper, the term “nanocomposites” is used in a broad context to cover drug nanoparticle-laden intermediate products in the form of powders, cakes, and extrudates, which can be incorporated into final oral solid dosages via standard pharmaceutical unit operations, as well as drug nanoparticle-laden strip films. The objective of this paper is to review studies from 2012⁻2017 in the field of drug-laden nanocomposites. After a brief overview of the various approaches used for preparing drug nanoparticles, the review covers drying processes and dispersant formulations used for the production of drug-laden nanocomposites, as well as various characterization methods including quiescent and agitated redispersion tests. Traditional dispersants such as soluble polymers, surfactants, other water-soluble dispersants, and water-insoluble dispersants, as well as novel dispersants such as wet-milled superdisintegrants, are covered. They exhibit various functionalities such as drug nanoparticle stabilization, mitigation of aggregation, formation of nanocomposite matrix⁻film, wettability enhancement, and matrix erosion/disintegration. Major challenges such as nanoparticle aggregation and poor redispersibility that cause inferior dissolution performance of the drug-laden nanocomposites are highlighted. Literature data are analyzed in terms of usage frequency of various drying processes and dispersant classes. We provide some engineering considerations in comparing drying processes, which could account for some of the diverging trends in academia vs. industrial practice. Overall, this review provides rationale and guidance for drying process selection and robust nanocomposite formulation development, with insights into the roles of various classes of dispersants.

pH-Responsive Mercaptoundecanoic Acid Functionalized Gold Nanoparticles and Applications in Catalysis.

Mercaptoundecanoic acid (MUA) functionalized gold nanoparticles (AuNP-MUA) were synthesized and demonstrated to possess pH-triggered aggregation and re-dispersion, as well as the capability of phase transfer between aqueous and organic phases in response to changes in pH. The pH of aggregation for AuNP-MUA is consistent with the pKa of MUA (pH ~4) in solution, while AuNP-MUA phase transition between aqueous and organic phases occurs at pH ~9. The ion pair formation between the amine group in octadecylamine (ODA), the carboxylate group in MUA, and the hydrophobic alkyl chain of ODA facilitates the phase transfer of AuNP-MUA into an organic medium. The AuNP-MUA were investigated as a reusable catalyst in the catalytic reduction of 4-nitrophenol by borohydride-a model reaction for AuNPs. It was determined that 100% MUA surface coverage completely inhibits the catalytic activity of AuNPs. Decreasing the surface coverage was shown to increase catalytic activity, but this decrease also leads to decreased colloidal stability, recoverability, and reusability in subsequent reactions. At 60% MUA surface coverage, colloidal stability and catalytic activity were achieved, but the surface coverage was insufficient to enable redispersion following pH-induced recovery. A balance between AuNP colloidal stability, recoverability, and catalytic activity with reusability was achieved at 90% MUA surface coverage. The AuNP-MUA catalyst can also be recovered at different pH ranges depending on the recovery method employed. At pH ~4, protonation of the MUA results in reduced surface charge and aggregation. At pH ~9, ODA will form an ion-pair with the MUA and induce phase transfer into an immiscible organic phase. Both the pH-triggered aggregation/re-dispersion and aqueous/organic phase transfer methods were employed for catalyst recovery and reuse in subsequent reactions. The ability to recover and reuse the AuNP-MUA catalyst by two different methods and different pH regimes is significant, based on the fact that nanoparticle-catalyzed reactions may occur under different pH conditions.

CO2 switchable hollow nanospheres.

HYPOTHESIS: Hollow nanospheres, characterized by a cavity inside a solid shell, have potential applications due to their unique structure, but the unchangeable morphology and permeability of the shell restrain their further practical utilization. While several smart hollow nanospheres that can respond to pH, ion strength, and temperature have been developed, they are inclined to suffer from problems associated with high energy consumption or the difficult removal of residual stimulants. Thus, it is desirable to develop a novel and free-of-residual trigger stimulating mode. EXPERIMENTS: In this work, CO2 is used to fabricate smart hollow nanospheres composed of crosslinked poly(diethylamino-ethyl methacrylate) (PDEAEMA) network from polystyrene (PS)/PDEAEMA core-shell nanospheres by a template-removal technique. The morphology evolution of the resultant nanospheres during the fabrication process was characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), thermogravimetry analysis (TGA) and dynamic light scattering (DLS) and was visualized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). FINDINGS: Hollow nanospheres can be generated by experiencing a morphology change from a core nanosphere, core-shell, yolk-shell to a final hollow structure. The increase in shell-stiffness can restrain the collapse of hollow spheres. It is demonstrated that CO2 is easy to introduce and remove (via N2 input) without stimulation residues in this system. In addition, mild CO2/N2 purging can only reversibly change the swelling/collapse of hollow particles; violent CO2/N2 bubbling can reversibly regulate both the size and aggregation/re-dispersion state of the hollow nanospheres, which can be intuitively observed by atomic force microscopy (AFM).