Enhancing the Quality of Polypropylene Recyclates: Predictive Modelling of the Melt Flow Rate and Shear Viscosity.

The extensive use of polypropylene (PP) in various industries has heightened interest in developing efficient methods for recycling and optimising its mixtures. This study focuses on formulating predictive models for the Melt Flow Rate (MFR) and shear viscosity of PP blends. The investigation involved characterising various grades, including virgin homopolymers, copolymers, and post-consumer recyclates, in accordance with ISO 1133 standards. The research examined both binary and ternary blends, utilising traditional mixing rules and symbolic regression to predict rheological properties. High accuracy was achieved with the Arrhenius and Cragoe models, attaining R2 values over 0.99. Symbolic regression further enhanced these models, offering significant improvements. To mitigate overfitting, empirical noise and variable swapping were introduced, increasing the models' robustness and generalisability. The results demonstrated that the developed models could reliably predict MFR and shear viscosity, providing a valuable tool for improving the quality and consistency of PP mixtures. These advancements support the development of recycling technologies and sustainable practices in the polymer industry by optimising processing and enhancing the use of recycled materials.

Comprehensive rheological and mechanistic evaluation of an asphalt binder and mixture modified with warm mix additives.

Though warm mix asphalt (WMA) technology has been introduced for a long time, there is still reluctance in the industry to utilize it in practice. In regions like India, where WMA incorporation into road construction has been limited over the past two decades, building confidence in local binders is imperative for widespread adoption. Thus, the present study appraises the effect of three commonly used WMA additives in India, namely Sasobit®, Evotherm®, and Zycotherm®, with base binder VG-30 on the rheological and mixture performance parameters. Three dosages of each WMA additive were blended with the control binder to give ten binder combinations. Different binder evaluations such as Superpave grading and parameters, frequency sweep testing, multiple stress creep recovery test, and linear amplitude sweep test were conducted for comparative dynamic mechanical analysis. Based on the binder testing results, suitable dosages of WMA additives were established, and mixture testing was carried out using these specific additive dosages. Binder evaluations showed improvement in high-temperature characteristics with Sasobit® and better fatigue performance with Evotherm®, while Zycotherm® did not alter binder properties significantly. The asphalt mixture testing results indicated satisfactory performance with the three additives based on Marshall stability and flow testing. The WMA additives also showed enhancement in moisture susceptibility based on the modified Lottman test with Zycotherm® demonstrating the best performance. Overall, the study underscores promising effects of the three WMA additives across different parameters, signaling their potential for widespread application in real-world scenarios.

Controlling sodium chloride concentration modulates the supramolecular structure and sol features of wheat starch-acetylated starch binary matrix.

The sol performance of wheat starch (WS) matrix incorporating acetylated starch (AS) is crucial for the processing and quality features of wheat products. From a supramolecular structure view, how regulating salt (sodium chloride) concentration modulates the sol features, e.g., pasting, zero-shear viscosity (ZSV) and thixotropy of WS-AS binary matrix was explored. Compared to the salt-free counterpart, the saline matrices exhibited a delayed pasting profile and a decreased viscoelasticity. Thereinto, the sol at 0.02 M NaCl exhibited the smallest ZSV (23,710 Pa·s) and the greatest in-shear recovery ratio (33.7 %). Such variations could be attributed to the weakened coil-helix, nematic-smectic and isotropy-anisotropy transitions from a side-chain liquid-crystalline perspective. Meanwhile, the correlation length (ξ) and radius of gyration (Rg) obtained from small angle X-ray scattering analysis were increased by 5.2 and 9.6 Å respectively, which disclosed a restrained entanglement and an enhanced chain mobility. These results would provide a reference for the design of fluid/semisolid products with optimized qualities.

Structural and mechanical behavior of type-I collagen fibrils in presence of induced electrostatic interactions through ionic liquids.

Tuning the self-assembly of collagen has broad applications in the biomedical field owing to their desired biological performance as collagenous materials with tunable functionalities can further determine cellular responses. In this work, an attempt has been made to tune the self-assembly of collagen using ionic liquids, viz., imidazolium chloride (IC) and choline dihydrogen phosphate (CDHP) at its physiological pH, followed by probing assembled systems using various characterization methods. Turbidity measurements of fibrillar networks were performed to ascertain the rate of fibril formation in addition of imidazolium chloride and choline dihydrogen phosphate to collagen at physiological pH. Morphological changes were examined using Scanning Electron Microscope (SEM), binding affinities were measured by Microscale Thermophoresis (MST), in addition to, changes in the shear viscosity, mechanical strength of collagen fibrils when interacted with imidazolium and choline based ILs were carried out using rotational rheometer and Quartz Crystal Microbalance (QCM) measurements. Experimental result depicts that CDHP imparts better crosslinking as well as mechanical strength compare to IC, which is already known for destabilizing the triple helix structure is inhibiting the fibril formation. This self-assembled, ionic-liquid treated collagen-fibrillar system would accelerate various force modulated fibrillar network study, for mimicking the ECM and tissue engineering application.

Rigid Rod-like Viscoelastic Behaviors of Methyl Cellulose Samples with a Wide Range of Molar Masses Dissolved in Aqueous Solutions.

The viscoelastic behaviors of aqueous solutions of commercially available methyl cellulose (MC) samples with a degree of substitution of 1.8 and a wide range of weight average molar masses (Mw) were investigated over a wide concentration (c) range at some temperatures from -10 to 25 °C. The viscoelastic parameters useful to discuss the structure and dynamics of MC-forming particles in aqueous solutions were precisely determined, such as the zero-shear viscosity (η0), the steady-state compliance (Je), the average relaxation time (τw), and the activation energy (E*) of τw. Because previously obtained scattering and intrinsic viscosity ([η]) data revealed that the MC samples possess a rigid rod-like structure in dilute aqueous solutions over the entire Mw range examined, the viscoelastic data obtained in this study were discussed in detail based on the concept of rigid rod particle suspension rheology. The obtained Je-1 was proportional to the number density of sample molecules (ν = cNAMw-1, where NA means the Avogadro's constant) over the ν range examined irrespective of Mw. The reduced relaxation time (4NAτw(3νJe [η]ηmMw)-1), where ηm means the medium viscosity, was proportional to (νL3)2, L; the average particle length depending on Mw for each sample was determined in a previous study; and the reduced specific viscosity (ηspNAL3(Mw [η])-1), where ηsp means the specific viscosity, was proportional to (νL3)3 in a range of νL3 < 3 × 102. These findings were typical characteristics of the rigid rod suspension rheology. Therefore, the MC samples behave as entangling rigid rod particles in the νL3 range from rheological points of view. A stepwise increase in E* was clearly observed in a c range higher than the [η]-1 value irrespective of Mw. This observation proposes that contact or entanglement formation between particles formed by MC molecules results in an increase in E*.

Wall Slip-Free Viscosity Determination of Filled Rubber Compounds Using Steady-State Shear Measurements.

The high-pressure capillary rheometer (HPCR) represents a state-of-the-art instrument for the determination of rheological properties for plastics and rubber compounds. Rubber compounds have an increased tendency to exhibit flow anomalies depending on the compound ingredients and the processing parameters. Combined with non-isothermal effects due to dissipative material heating, this causes rheological material measurements and the resulting material parameters derived from them to be affected by errors, since the fundamental analytical and numerical calculation approaches assume isothermal flow and wall adhesion. In this paper, the applicability of the empirical rheological transfer function of the Cox-Merz rule, which establishes a relationship between shear viscosity measured with a HPCR and complex viscosity measured with a closed cavity rheometer (CCR), is investigated. The Cox-Merz relation could not be verified for an unfilled EPDM raw polymer or for filled, practical rubber compounds. Using a closed cavity rheometer, a methodology based on ramp tests is then introduced to collect wall slip-free steady-state shear viscosity data under isothermal conditions. The generated data show high agreement with corrected viscosity data generated using the HPCR, while requiring less measurement effort.

On Characterization of Shear Viscosity and Wall Slip for Concentrated Suspension Flows in Abrasive Flow Machining.

In the realm of abrasive flow machining (AFM), precise finishing and maintaining dimensional accuracy have remained challenging due to non-uniformities in the AFM process and complexities associated with the abrasive media's shear viscosity and wall slip behavior. By addressing these challenges, this study introduces a comprehensive framework, combining theoretical foundations, measurement techniques, and experimental setups. Utilizing capillary flow, a novel compensation strategy is incorporated within the Mooney method to counter entrance pressure drop effects. This enhanced capillary flow method emerges as a promising alternative to the conventional Cox-Merz empirical rule, enabling precise characterization of wall slip behavior and shear viscosity, particularly at elevated shear rates. The abrasive media exhibit a Navier nonlinear wall slip, as highlighted by the Mooney method. Rigorous verification of the proposed methodologies and models against supplemental experiments showcases a high degree of congruence between predicted and observed results, emphasizing their accuracy and broad application potential in AFM. This research illuminates the intricacies of the abrasive media's behavior, accentuating the need for meticulous characterization, and provides a robust foundation for genuine modeling and predictions in material removal within AFM.

Rheology of liquid foods under shear flow conditions: Recently used models.

Proper modeling of flow or viscosity curves as a function of shear rate is a useful tool in any engineering activity. The rheology of foods depends on the composition, processing to which they have been subjected and the state of dispersion in which they are found. Liquid foods are complex biosystems, that show non-Newtonian behavior under flow conditions. This review presents models used in recent decades to describe the experimental rheological behavior of various liquid foods, ranging from Newtonian fluids to the most complex. Some non-Newtonian parameters such as those of the Ostwald-de Waele, Bingham, Herschel-Bulkley, Casson, Cross, and Carreau models are summarized. Examples of thixotropic behavior described by the Weltman and Abu-Jdayil models are also presented. In each model, explanations based on the composition and dispersion state of the food are made. This is useful in innovative processing technologies and for scientists new to the field of food rheology. An attempt is made to exemplify and group the expected behavior for most fluid foods, including some for a dysphagia diet, depending on their composition or the dispersed system formed, which will be useful for professionals who wish to compare reported rheological parameters with those obtained experimentally.

Pseudo hard-sphere viscosities from equilibrium Molecular Dynamics.

Transport coefficients like shear, bulk and longitudinal viscosities are sensitive to the intermolecular interaction potential and finite size effects when are numerically determined. For the hard-sphere (HS) fluid, such transport properties are determined almost exclusively with computer simulations. However, their systematic determination and analysis throughout shear stress correlation functions and the Green-Kubo formalism can not be done due to discontinuous nature of the interaction potential. Here, we use the pseudo hard-sphere (PHS) potential to determine pressure correlation functions as a function of volume fraction in order to compute mentioned viscosities. Simulation results are compared to available event-driven molecular dynamics of the HS fluid and also used to propose empirical corrections for the Chapman-Enskog zero density limit of shear viscosity. Moreover, we show that PHS potential is a reliable representation of the HS fluid and can be used to compute transport coefficients. The molecular simulation results of the present work are valuable for further exploration of HS-type fluids or extend the approach to compute transport properties of hard-colloid suspensions.

Fluid Properties Extraction in Confined Nanochannels with Molecular Dynamics and Symbolic Regression Methods.

In this paper, we propose an alternative road to calculate the transport coefficients of fluids and the slip length inside nano-conduits in a Poiseuille-like geometry. These are all computationally demanding properties that depend on dynamic, thermal, and geometrical characteristics of the implied fluid and the wall material. By introducing the genetic programming-based method of symbolic regression, we are able to derive interpretable data-based mathematical expressions based on previous molecular dynamics simulation data. Emphasis is placed on the physical interpretability of the symbolic expressions. The outcome is a set of mathematical equations, with reduced complexity and increased accuracy, that adhere to existing domain knowledge and can be exploited in fluid property interpolation and extrapolation, bypassing timely simulations when possible.

Shear-Viscosity-Dependent Effect of a Gum-Based Thickening Product on the Safety of Swallowing in Older Patients with Severe Oropharyngeal Dysphagia.

Fluid thickening is a valid therapeutic strategy for patients with oropharyngeal dysphagia (OD). The main aim of this study was to determine the therapeutic effect of the xanthan-gum-based thickener Tsururinko Quickly (TQ, Morinaga Milk Co., Tokyo, Japan) in older patients with severe OD. A total of 85 patients (83.32 ± 6.75 y) with OD and a penetration-aspiration score (PAS) of n ≥ 3 were studied by videofluoroscopy while swallowing duplicate 10 mL boluses at <50 mPa·s, 100, 200, 400, 800, and 1600 mPa·s, to assess the safety and efficacy of swallowing and the biomechanics of a swallowing response at each viscosity level. At <50 mPa·s, only 16.25% patients swallowed safely, 45% had penetrations (PAS 3-5), and 38.75% had aspirations (PAS 6-8). Fluid thickening with TQ greatly increased the prevalence of patients with safe swallowing from 62.90% at 100 mPa·s to 95.24% at 1600 mPa·s in a shear-viscosity-dependent manner. The penetrations and aspirations were significantly reduced to 3.60% and 1.19%, respectively, at 1600 mPa·s. The threshold viscosity was 100 mPa·s and the increasing viscosity above 800 mPa·s did not further improve the therapeutic effect significantly. Increasing the shear viscosity significantly reduced the time to laryngeal vestibule closure (-16.70%), increased the time to upper oesophageal sphincter opening (+26.88%), and reduced the pharyngeal bolus velocity (-31.62%) without affecting the pharyngeal residue. TQ has a strong shear-viscosity-dependent effect on the safety of swallowing in older patients with severe OD without increasing the pharyngeal residue. The therapeutic range for TQ is 100-800 mPa·s, with 200 and 800 mPa·s being the optimal doses to cover the needs of older patients with OD.

Atomic transport properties and liquid-liquid phase separation of ZnxBi1-xliquid monotectic alloys.

Atomic transport properties specifically the shear viscosity and the diffusion coefficient for ZnxBi1-xliquid monotectic segregating alloys are theoretically investigated by using the Rice-Allnatt theory. The essential ingredient for the microscopic description of the metals and their alloys is the interionic interaction which in the present work is described by a widely used local pseudopotential. The temperature dependent behaviour of the above mentioned physical properties is also examined. The overall agreement of our calculated results with the available experimental data is found to be good for the full range of concentration. More interestingly, the temperature dependent results for the viscosity and the diffusion coefficient apparently exhibit a signature of liquid-liquid phase separation through a sudden bending in their concentration dependent profiles. Onset of this bending also provides information about the critical temperature and the critical concentration, and also provides a value for the critical exponent of liquid-liquid phase separation.

Extensional Rheology of Poly(vinylidene fluoride)/N,N-dimethylformamide Solutions.

Typical extension flow occurs in electrospinning process of Poly(vinylidene fluoride) (PVDF) solutions such that researchers focus on extensional rheological behaviors of PVDF solutions. The extensional viscosity of PVDF solutions is measured to know the fluidic deformation in extension flows. The solutions are prepared by dissolving PVDF powder into N,N-dimethylformamide (DMF) solvent. A homemade extensional viscometric device is used to produce uniaxial extension flows and the feasibility of the viscometric device is verified by applying the glycerol as a test fluid. Experimental results show that PVDF/DMF solutions are extension shinning as well as shear shinning. The Trouton ratio of thinning PVDF/DMF solution is close to three at very low strain rate and then reaches a peak value until it drops to a small value at high strain rate. Furthermore, an exponential model may be used to fit the measured values of uniaxial extensional viscosity at various extension rates, while traditional power-law model is applicable to steady shear viscosity. For 10~14% PVDF/DMF solution, the zero-extension viscosity by fitting reaches 31.88~157.53 Pa·s and the peak Trouton ratio is 4.17~5.16 at applied extension rate of less than 34 s-1. Characteristic relaxation time is λ~100 ms and corresponding critical extension rate is ε˙c~5 s-1. The extensional viscosity of very dilute PVDF/DMF solution at very high extension rate is beyond the limit of our homemade extensional viscometric device. This case needs a higher sensitive tensile gauge and a higher-accelerated motion mechanism for test.

Improvement in Processability for Injection Molding of Bisphenol-A Polycarbonate by Addition of Low-Density Polyethylene.

The rheological properties and processability at injection molding were studied for bisphenol-A polycarbonate (PC) that was modified by low-density polyethylene (LDPE) having a low shear viscosity. The LDPE addition significantly decreased the steady-state shear viscosity, especially in the high shear rate region. The decrease did not originate from slippage on the die wall but due to interfacial slippage between the PC and dispersed LDPE droplets that deformed to the flow direction to a great extent. As a result of the viscosity decrease, injection pressure largely decreased from 150 to 110 MPa with the addition only 5 wt.% of LDPE. The enhanced flowability also reduced the warpage of the molded product significantly, demonstrating that the processability at injection molding was improved by the addition of LDPE.

Rheological Issues on Oropharyngeal Dysphagia.

There is an increasing proof of the relevance of rheology on the design of fluids for the diagnosis and management of dysphagia. In this sense, different authors have reported clinical evidence that support the conclusion that an increase in bolus viscosity reduces the risks of airway penetration during swallowing. However, this clinical evidence has not been associated yet to the definition of objective viscosity levels that may help to predict a safe swallowing process. In addition, more recent reports highlight the potential contribution of bolus extensional viscosity, as elongational flows also develops during the swallowing process. Based on this background, the aim of this review paper is to introduce the lecturer (experts in Dysphagia) into the relevance of Rheology for the diagnosis and management of oropharyngeal dysphagia (OD). In this sense, this paper starts with the definition of some basic concepts on Rheology, complemented by a more extended vision on the concepts of shear viscosity and elongational viscosity. This is followed by a short overview of shear and elongational rheometrical techniques relevant for the characterization of dysphagia-oriented fluids, and, finally, an in-depth analysis of the current knowledge concerning the role of shear and elongational viscosities in the diagnosis and management of OD (shear and elongational behaviors of different categories of dysphagia-oriented products and contrast fluids for dysphagia assessment, as well as the relevance of saliva influence on bolus rheological behavior during the swallowing process).

Investigation and prediction of the extensional viscosity of okra mucilage using the Giesekus model.

BACKGROUND: Okra is a vegetable that is widely grown around the world. Okra mucilage contains a high mucus concentration that can be useful for supporting the swallowing process. Although the extensional rheology of okra mucilage is essential to its flow, its extensional viscosity has not received much attention. OBJECTIVE: Using a filament stretching rheometer, the extensional viscosity of the mucilage in okra was examined. The Giesekus model was used to predict this parameter. METHODS: The okra mucilage with different concentrations was extracted from fresh okra. The extensional viscosity was measured using a filament breakup apparatus. The diameter of the liquid bridge was measured by a laser micrometer and it was also observed by a high-speed camera. A rotational rheometer was used to measure the shear viscosity. In addition, the master curves for the shear viscosity were plotted to eliminate the influence of solvent and shear rate and evaluate the influence of concentration on the elasticity of okra mucilage. The okra mucilage shear and extensional viscosity were predicted using the Giesekus model. RESULTS: Every sample of okra mucilage exhibited shear thinning behavior. In addition to having a high extensional viscosity that is hundreds of times higher than its shear viscosity, okra mucilage also exhibited stretching phenomena. The master curves demonstrated that the pseudoplasticity of the okra mucilage increased along with the concentration. The rheological behavior of the mucilage in okra can be explained by the Giesekus model. CONCLUSIONS: Okra mucilage's shear viscosity exhibited shear thinning behavior and a strong extensional viscosity that was significantly higher than its shear viscosity. The shear and extensional viscosity of okra mucilage can be described and predicted using the Giesekus model.

aRDG Analysis of Asphaltene Molecular Viscosity and Molecular Interaction Based on Non-Equilibrium Molecular Dynamics Simulation.

Understanding the noncovalent (weak) interactions between asphaltene molecules is crucial to further comprehending the viscosity and aggregation behavior of asphaltenes. In the past, intermolecular interactions were characterized indirectly by calculating the radial distribution function and the numerical distribution of distances/angles between atoms, which are far less intuitive than the average reduced density gradient (aRDG) method. This study selected three representative asphaltene molecules (AsphalteneO, AsphalteneT, and AsphalteneY) to investigate the relationship between viscosity and weak intermolecular interactions. Firstly, a non-equilibrium molecular dynamics (NEMD) simulation was employed to calculate the shear viscosities of these molecules and analyze their aggregation behaviors. In addition, the types of weak intermolecular interactions of asphaltene were visualized by the aRDG method. Finally, the stability of the weak intermolecular interactions was analyzed by the thermal fluctuation index (TFI). The results indicate that AsphalteneY has the highest viscosity. The aggregation behavior of AsphalteneO is mainly face-face stacking, while AsphalteneT and AsphalteneY associate mainly via offset stacking and T-shaped stacking. According to the aRDG analysis, the weak interactions between AshalteneT molecules are similar to those between AshalteneO molecules, mainly due to van der Waals interactions and steric hindrance effects. At the same time, there is a strong attraction between AsphalteneY molecules. Additionally, the results of the TFI analysis show that the weak intermolecular interactions of the three types of asphaltene molecules are relatively stable and not significantly affected by thermal motion. Our results provide a new method for better understanding asphaltene molecules' viscosity and aggregation behavior.

Shear Viscosity Overshoots in Polymer Modified Asphalts.

Polymer modification is one of the most common methods for improving the performance of asphalt binders. Despite in-depth research, the structural modifications induced by polymers are still not well understood. In this work, steady shear viscosity measurements and cryo-scanning electron microscopy (cryo-SEM) were used to better understand the internal structure of asphalts modified by styrene-butadiene-styrene with and without sulfur as a crosslinking agent, asphalts modified by polyphosphoric acid (PPA), and quaternary asphalt blends modified by SBS, sulfur, and PPA. The results showed that polymer and asphaltenes collaborate, thus SBS forms a three-dimensional network strengthened by asphaltenes clusters. The strength, extension, and physical nature of such a network is revealed by the appearance of overshoots in the viscosity curves. Moreover, the indirect information deduced from the magnitude and shape of the shear viscosity curves successfully correlated with direct observations of the internal structure by cryo-SEM. Steady shear viscosity is thus recommended as a useful tool in studying the structural development of asphalts modified by different technologies.

Zero Shear Viscosity of Hybrid Modified Asphalts and Its Gray Correlation with Other Properties.

The viscosity of modified asphalt binders is the most important property to ensure the durability of open-graded friction course (OGFC). Zero shear viscosity (ZSV) is considered to be the optimum result to reflect the rutting characterization of high viscosity modified asphalt binders, compared with conventional vacuum capillary viscosity. However, there are few reports on using ZSV to evaluate the material characteristics of hybrid modified asphalt binders and to establish the relationship between ZSV and other properties. In this paper, a high viscosity hybrid modified asphalt binder was prepared with Sty-rene-butadiene-styrene (SBS) and Crumb rubber modifier (CRM). ZSV, three major indicators, 60 °C dynamic viscosity, 135 °C Brookfield viscosity, and a dynamic rheological test were used to determine the properties of the hybrid modified asphalt binders. The relationship between ZSV and other properties was studied by the gray correlation analysis method. Results indicated that: (1) The viscosity of hybrid modified asphalt binders increases with the decreasing frequency. When the frequency tends to 0, the viscosity of asphalt at this time is zero shear viscosity; (2) The values of the ZSV of hybrid modified asphalt binders have a large increase as the dose of both CRM and SBS modifiers were increased; and (3) The ZSV at 60 °C correlated well with the performance properties of rutting factor (G*/sin(θ)), indicating that the ZSV of hybrid modified asphalt binders could be a good indicator of performance.

Possibility to Alter Dynamics of Luminescence from Surface of Polymer Membrane with Ultrasonic Waves.

The temporal dynamics of luminescence from the surface of Nafion polymer membranes have been studied. In fact, the polymer membrane was soaked in liquids with different contents of deuterium. The test liquids were ordinary (natural) water (deuterium content equal to 157 ppm) and deuterium-depleted water (deuterium content is equal to 3 ppm). Simultaneously with the excitation of luminescence, the Nafion plate was irradiated with ultrasonic pulses, having a duration of 1 µs. The ultrasonic waves were generated with different repetition rates and amplitudes, and irradiated the surface of Nafion in the geometry of grazing or normal incidence. Luminescence regimes were studied when the membrane was irradiated with one ultrasonic wave (one piezoelectric transducer) or two counter-propagating waves (two piezoelectric transducers). It turned out that ultrasonic waves, which fall normal to the membrane interface, do not affect the dynamics of luminescence. At the same time, in the case of ultrasonic irradiation in the grazing incidence geometry, sharp jumps in the luminescence intensity occur, and the behavior of these jumps substantially depends on the mode of irradiation: one or two piezoelectric transducers. This allows for control of the dynamics of luminescence from the polymer surface. In accordance with this model, the possibility of altering the luminescence dynamics is due to the effect of unwinding the polymer fibers from the surface toward the liquid bulk upon soaking. It is important that such unwinding does not occur in deuterium-depleted water, which was confirmed in a direct experiment with dynamic light scattering from polydisperse aqueous suspensions of Nafion nanometer-sized particles; these suspensions were prepared in ordinary water and deuterium-depleted water. Thus, ultrasonic irradiation affects the dynamics of luminescence only when Nafion is swollen in ordinary water; in the case of deuterium-depleted water this effect is missed.