ABSTRACT
Salt deposition is a disturbing problem that limits the development of passive solar-driven interfacial evaporation. Inspired by the passive fluid control mechanism of the Tesla valve, a novel solar evaporator is proposed with a Tesla valve-like water transport structure to prevent salt accumulation at the evaporation interface. A unique "ion diode" salt resistance of this evaporator is significantly achieved by optimizing the two asymmetric water transport structures, consisting of one Tesla valve-like side and one wide-leg side, which establish a reverse-suppressing and forward-accelerating water transport channel. In contrast to the limited ion migration of the typical symmetric solar evaporator, such a channel caused by the water/salt ions transport difference between two water supply structures, reinforces the water/salt ions supply on the wide-leg side, thus leading to an apparent unidirectional salt ions migration from the wide-leg side to bulk water through the Tesla valve-like side. Consequently, an evaporation rate of 3.25 kg m-2 h-1 and a conversion efficiency of 83.27% under 2 suns are achieved in 16 wt% NaCl solution. The development of the Tesla Valve-like evaporator provides a new perspective for solving salt deposition and realizing scalable applications of solar-driven interfacial evaporation.
ABSTRACT
In recent years, photovoltaic/thermal (PV/T) systems have played a crucial role in reducing energy consumption and environmental degradation, nonetheless, the low energy conversion efficiency presents a considerable obstacle for PV/T systems. Therefore, improving heat conversion efficiency is essential to enhance energy efficiency. In this paper, the PV/T system with the Tesla valve is proposed to solve this problem. Firstly, the cooling effect is simulated and analyzed in the system with four different flow channel structures: semicircle, rectangle, triangle and Tesla valve. The results indicate that the system with the Tesla valve exhibits superior cooling performance. Subsequently, several factors including angle, valve number, valve type, and pipe diameter ratio for the Tesla valve are further studied through numerical and simulation analysis. The results reveal that Tesla valves demonstrate optimal cooling performance when possessing the following structural parameters: complete symmetry, more valves, a 30-degree angle and a pipe diameter ratio of 1. Finally, four different types of fluid are selected to explore the Tesla valve. The conclusion shows that nanofluids with high density, low specific heat, and high thermal conductivity also improve the cooling performance. Thus, the PV/T system with the Tesla valve exhibits good heat dissipation and energy storage efficiency, electrical efficiency can reach 16.32% and thermal efficiency reach 59.65%.
ABSTRACT
The Tesla valve is a non-moving check valve used in various industries to control fluid flow. It is a passive flow control device that does not require external power to operate. Due to its unique geometry, it causes more pressure drop in the reverse direction than in the forward direction. This device's optimal performance in heat transfer applications has led to the use of Tesla valve designs in heat sinks and heat exchangers. This study investigated a Tesla valve with unconventional geometry through numerical analysis. Two geometrical parameters and inlet velocity were selected as input variables. Also, the pressure drop ratio (PDR) and temperature difference ratio (TDR) parameters were chosen as the investigated responses. By leveraging numerical data, artificial neural networks were trained to construct precise prediction models for responses. The optimal designs of the Tesla valve for different conditions were then reported using the genetic algorithm method and prediction models. The results indicated that the coefficient of determination for both prediction models was above 0.99, demonstrating high accuracy. The most optimal PDR value was 4.581, indicating that the pressure drop in the reverse flow direction is 358.1% higher than in the forward flow direction. The best TDR response value was found to be 1.862.
ABSTRACT
Expansion of the microfluidics field dictates the necessity to constantly improve technologies used to produce such systems. One of the approaches which are used more and more is femtosecond (fs) direct laser writing (DLW). The subtractive model of DLW allows for directly producing microfluidic channels via ablation in an extremely simple and cost-effective manner. However, channel surface roughens are always a concern when direct fs ablation is used, as it normally yields an RMS value in the range of a few µm. One solution to improve it is the usage of fs bursts. Thus, in this work, we show how fs burst mode ablation can be optimized to achieve sub-µm surface roughness in glass channel fabrication. It is done without compromising on manufacturing throughput. Furthermore, we show that a simple and cost-effective channel sealing methodology of thermal bonding can be employed. Together, it allows for production functional Tesla valves, which are tested. Demonstrated capabilities are discussed.
ABSTRACT
Graphene has exceptional electronic properties, such as zero band gap, massless carriers, and high mobility. These exotic carrier properties enable the design and development of unique graphene devices. However, traditional semiconductor solvers based on drift-diffusion equations are not capable of modeling and simulating the charge distribution and transport in graphene, accurately, to its full extent. The effects of charge inertia, viscosity, collective charge movement, contact doping, etc., cannot be accounted for by the conventional Poisson-drift-diffusion models, due to the underlying assumptions and simplifications. Therefore, this article proposes two mathematical models to analyze and simulate graphene-based devices. The first model is based on a modified nonlinear Poisson's equation, which solves for the Fermi level and charge distribution electrostatically on graphene, by considering gating and contact doping. The second proposed solver focuses on the transport of the carriers by solving a hydrodynamic model. Furthermore, this model is applied to a Tesla-valve structure, where the viscosity and collective motion of the carriers play an important role, giving rise to rectification. These two models allow us to model unique electronic properties of graphene that could be paramount for the design of future graphene devices.
ABSTRACT
Current three-dimensional micromixers for continuous flow reactions and nanoparticle synthesis are complex in structure and difficult to fabricate. This paper investigates the design, fabrication, and characterization of a novel micromixer that uses a simple spatial Tesla valve design to achieve efficient mixing of multiple solutions. The flow characteristics and mixing efficiencies of our Tesla valve micromixer are investigated using a combination of numerical simulations and experiments. The results show that in a wide range of flow rates, viscoelastic solutions with different concentrations can be well mixed in our micromixer. Finally, experiments on the synthesis of chitosan nanoparticles are conducted to verify the practicability of our micromixer. Compared with nanoparticles prepared by conventional magnetic stirring, the size of nanoparticles prepared by micromixing is smaller and the distribution is more uniform. Therefore, our Tesla valve micromixer has significant advantages and implications for mixing chemical and biological reactions.
Subject(s)
Chitosan , Nanoparticles , Equipment DesignABSTRACT
Sweat sensor has become one of the most important developing directions of in vitro wearable diagnostic device in recent years. Stable sweat collecting device is the key to realize sweat component analysis. In order to ensure that the collected sweat is not subject to component analysis errors caused by evaporation or environmental pollution, mechanical micro-valves were adopted for microfluidic sweat collection devices to realize sealed storage of sweat. However, this poses a challenge to the stability of machining and reusability of the acquisition device. In this work, the Tesla valve without any mechanical structure were introduced into the design of sweat collection chip. And made full use of its diodicity to improve the collection to a certain extent, prevent backflow at the entrance, and restrain the flow at the exit to contact with the outside world. In addition, through optimizing the shunt angle, branch channel parameters of Tesla valve, boosted its diodicity under low flow rate. Furthermore, a sweat storage chamber with baffle structure that can achieve maximum static storage area was adopted to form a whole sweat collection chip. The design was verified through the flow experiment of methylene blue and methyl red indicators on the chip. Through modification of the filter paper fixed in the collection chamber, the colorimetric analysis of glucose and pH was realized. This device may provide new inspirations for the development of wearable sweat sensor.
Subject(s)
Biosensing Techniques , Wearable Electronic Devices , Colorimetry , Glucose , Lab-On-A-Chip Devices , SweatABSTRACT
Looking to nature for inspiration has led to many diverse technological advances. The spiral valve intestine of sharks has provided the opportunity to observe the efficiency of different valve systems. It is supposed that the spiral intestine present in sharks, skates and rays slows the transit rate of digesta through the gut and provides increased surface area for the absorption of nutrients. In this investigation, we use a novel technique-creating three-dimensional reconstructions from CT scans of spiral intestines-to describe the morphology of the spiral intestine of at least one species from 22 different shark families. We discuss the morphological data in an evolutionary, dietary and functional context. The evolutionary analyses suggest that the columnar morphology is the ancestral form of the spiral intestine. Dietary analyses reveal no correlation between diet type and spiral intestine morphology. Flow rate was slowed significantly more when the two funnel-shaped spiral intestines were subjected to flow in the posterior to anterior direction, indicating their success at producing unidirectional flow, similar to a Tesla valve. These data are available to generate additional three-dimensional morphometrics, create computational models of the intestine, as well as to further explore the function of the gastrointestinal tract of sharks in structural and physiological contexts.
Subject(s)
Sharks , Skates, Fish , Animals , Biological Evolution , Gastrointestinal Tract , Humans , IntestinesABSTRACT
In this study, the Tesla-valve (TV) baffles were used to optimize the flow field in a column photobioreactor (PBR) in order to promote mass transfer of CO2 gas in the solution. The TV baffles were composed of many tilted plates with central holes and curved arcs facing downwards, installed along inner rising section of the column PBR. Many clockwise and anti-clockwise vortices were generated during the rising flow while passing through proposed TV baffles. An optimum TV baffle structure (30° plate angle, 8 cm arc width) decreased mixing time by 36.4% and increased the mass transfer coefficient by 50%. The TV baffles supported the movement of the A.platensis cells between light and dark regions to enhance their photochemical efficiency ÏPSII by 24.6% and Fv/Fm by 12.7%. Therefore, the biomass yield increased by 28.1% and exhibited an increased helix pitch and trichome length in comparison with traditional column PBR without baffles.
Subject(s)
Microalgae , Spirulina , Biomass , PhotobioreactorsABSTRACT
Tesla turbine and its applications in power generation and fluid flow were demonstrated by Nicholas Tesla in 1913. However, its real-world implementations were limited by the difficulty to maintain laminar flow between rotor disks, transient efficiencies during rotor acceleration, and the lack of other applications that fully utilize the continuous flow outputs. All of the aforementioned limits of Tesla turbines can be addressed by scaling to the microfluidic flow regime. Demonstrated here is a microscale Tesla pump designed and fabricated using a Digital Light Processing (DLP) based 3D printer with 43 µm lateral and 30 µm thickness resolutions. The miniaturized pump is characterized by low Reynolds number of 1000 and a flow rate of up to 12.6 mL/min at 1200 rpm, unloaded. It is capable of driving a mixer network to generate microfluidic gradient. The continuous, laminar flow from Tesla turbines is well-suited to the needs of flow-sensitive microfluidics, where the integrated pump will enable numerous compact lab-on-a-chip applications.