Confinement Effect of Plasmon for the Fabrication of Interconnected AuNPs through the Reduction of Diazonium Salts.

This paper describes a rapid bottom-up approach to selectively functionalize gold nanoparticles (AuNPs) on an indium tin oxide (ITO) substrate using the plasmon confinement effect. The plasmonic substrates based on a AuNP-free surfactant were fabricated by electrochemical deposition. Using this bottom-up technique, many sub-30 nm spatial gaps between the deposited AuNPs were randomly generated on the ITO substrate, which is difficult to obtain with a top-down approach (i.e., E-beam lithography) due to its fabrication limits. The 4-Aminodiphenyl (ADP) molecules were grafted directly onto the AuNPs through a plasmon-induced reduction of the 4-Aminodiphenyl diazonium salts (ADPD). The ADP organic layer preferentially grew in the narrow gaps between the many adjacent AuNPs to create interconnected AuNPs. This novel strategy opens up an efficient technique for the localized surface modification at the nanoscale over a macroscopic area, which is anticipated to be an advanced nanofabrication technique.

Large Capacity Enhancement of Carbon Electrodes by Solution Processing for High Density Energy Storage.

An inexpensive, solution phase modification of flat carbon electrodes by electrochemical reactions of a 1,8-diaminonaphthalene derivative results in a 120- to 700-fold increase in capacity by formation of a 15-22 nm thick organic film. Modification of high surface area carbon electrodes with the same protocol resulted in a 12- to 82-fold increase in capacity. The modification layer contains 9-15% nitrogen present as -NH- redox centers that result in a large Faradaic component involving one H+ ion for each electron. The electrodes showed no capacity loss after prolonged cycling in 0.1 M H2SO4 and exhibited significantly higher charge density than similar reported electrodes based on graphene and polyaniline. Investigation of the deposition conditions revealed that N-doped oligomeric ribbons are formed both by diazonium ion reduction and diaminonaphthalene oxidation, and the 1,8 isomer is essential for the large capacity increases. The capacity increase has at least three contributions: increased microscopic surface area from ribbon formation, Faradaic reactions of nitrogen-containing redox centers, and changes in ribbon conductivity resulting from polaron formation. An aqueous fabrication process was developed which both increased capacity and improved stability and was amenable to industrial production. The high charge density, low-cost fabrication, and <25 nm thickness of the diaminonaphthalene-derived films should prove attractive toward practical application on both flat surfaces and in high surface area carbon electrodes.

Surface Characteristics of Microporous and Mesoporous Carbons Functionalized with Pentafluorophenyl Groups.

The in situ diazonium reduction reaction is a reliable and well-known approach for the surface modification of carbon materials for use in a range of applications, including in energy conversion, as chromatography supports, in sensors, etc. Here, this approach was used for the first time with mesoporous colloid-imprinted carbons (CICs), materials that contain ordered monodisperse pores (10-100 nm in diameter) and are inherently highly hydrophilic, using a common microporous carbon (Vulcan carbon (VC)), which is relatively more hydrophobic, for a comparison. The ultimate goal of this work was to modify the CIC wettability without altering its nanostructure and also to lower its susceptibility to oxidation, as required in fuel cell and battery electrodes, by the attachment of pentafluorophenyl (-PhF5) groups onto their surfaces. This was shown to be successful for the CIC, with the -PhF5 groups uniformly coating the inner pore walls at a surface coverage of ca. 90% and allowing full solution access to the mesopores, while the -PhF5 groups deposited only on the outer VC surface, likely blocking its micropores. Contact angle kinetics measurements showed enhanced hydrophobicity, as anticipated, for both the -PhF5 modified CIC and VC materials, even revealing superhydrophobicity at times for the CIC materials. In contrast, water vapor sorption and cyclic voltammetry suggested that the micropores remained hydrophilic, arising from the deposition of smaller N- and O-containing surface groups, caused by a side reaction during the in situ diazonium functionalization process.