Untargeted Analysis of Short-Chain Peptides in Urine Samples Short Peptides Analysis.

Short-chain peptides have attracted increasing attention in different research fields, including biomarker discovery, but also a well-known analytical challenge in complex matrices due to their low abundance compared to other molecules, which can cause extensive ion suppression during mass spectrometric acquisition. Moreover, there is a lack of analytical workflows for their comprehensive characterization since ordinary peptidomics strategies cannot identify them. In this context, an enrichment strategy was introduced and developed to isolate and clean up short-chain peptides by graphitized carbon black solid phase extraction. For better coverage of peptide polarity, urine samples were analyzed by ultrahigh performance liquid chromatography by reversed-phase and hydrophilic interaction liquid chromatography. High-resolution mass spectrometry allowed the detection of the eluting peptides by data-dependent mode using a suspect screening strategy with an inclusion list; peptides were identified by a semiautomated workflow implemented on Compound Discoverer. The complementarity of the orthogonal separation strategy was confirmed by peptide identification, resulting in 101 peptides identified from the RP runs, and 111 peptides from the HILIC runs, with 60 common identifications.

Magnetic graphitized carbon black based on crystal growth method combined with high-resolution mass spectrometry for screening of 300 pesticide residues in Radix Codonopsis and Angelica sinensis.

In this study, a high-throughput method for analyzing 300 pesticide residues in Radix Codonopsis and Angelica sinensis was established by liquid chromatography-quadrupole time-of-flight mass spectrometry (LC-Q-TOF/MS) using iron tetroxide loaded graphitized carbon black magnetic nanomaterial (GCB/Fe3O4) as the purification material. It was optimized that saturated salt water and 1 % acetate acetonitrile were used as the extraction solution, then the supernatant was purified with 2 g anhydrous CaCl2 and 300 mg GCB/Fe3O4. As a result, 300 pesticides in Radix Codonopsis and 260 in Angelica sinensis achieved satisfactory results. The limits of quantification of 91 % and 84 % of the pesticides in Radix Codonopsis and Angelica sinensis reached 10 µg/kg, respectively. The matrix-matched standard curves ranging from 10 to 200 µg/kg were established with correlation coefficients (R) above 0.99. The pesticides meeting SANTE/12682/2021 accounted for 91.3 %, 98.3 %, 100.0 % and 83.8 %, 97.3, 100.0 % of the total pesticides added in Radix Codonopsis and Angelica sinensis respectively, which were spiked at 10, 20,100 µg/kg. The technique was applied to screen 20 batches of Radix Codonopsis and Angelica sinensis. Five pesticides were detected, three of which were prohibited according to the Chinese Pharmacopoeia (2020 Edition). The experimental results showed that GCB/Fe3O4 coupled with anhydrous CaCl2 exhibited good adsorption performance and could be used for sample pretreatment of various pesticide residues in Radix Codonopsis and Angelica sinensis. Compared with the reported methods for determining pesticides in traditional Chinese medicine (TCM), the proposed method has the advantage of less time-consuming in the clean-up procedure. Furthermore, as a case study on root TCM, this approach may serve as a reference for other TCM.

Enantioselective voltammetric sensor based on mesoporous graphitized carbon black Carbopack X and fulvene derivative.

For medicine and pharmaceuticals, the problem of determining and recognizing the enantiomers of biologically active compounds is an actual issue because the enantiomers of the same substance can have different effects on living organisms. This paper describes the development of an enantioselective voltammetric sensor (EVS) based on a glassy carbon electrode (GCE) modified with mesoporous graphitized carbon black Carbopack X (CpX) and a fulvene derivative (1S,4R)-2-cyclopenta-2,4-dien-1-ylidene-1-isopropyl-4-methylcyclohexane (CpIPMC) for recognition and determination of tryptophan (Trp) enantiomers. Synthesized CpIPMC was characterized by 1 H and 13 C nuclear magnetic resonance (NMR), chromatography-mass spectrometry, and polarimetry. The proposed sensor platform was studied by Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Using the square-wave voltammetry (SWV), it was established that the developed sensor is an effective chiral platform for the quantitative determination of Trp enantiomers, including in a mixture and in biological fluids like urine and blood plasma, with adequate precision and recovery ranged from 96% to 101%.

Detection of seven Alternaria toxins in edible and medicinal herbs using ultra-high performance liquid chromatography-tandem mass spectrometry.

Alternaria mycotoxins are ubiquitous mycotoxins that contaminate food and animal feed. Here, an UPLC-MS/MS was developed and used for the detection of seven Alternaria mycotoxins in 19 different edible and medicinal herbs. Extensive optimization resulted in a simple and convenient sample preparation procedure with satisfactory extraction and a lower matrix effect. LOQs ranged from 0.01 to 2.0 ng/mL. Recoveries varied between 71.44% and 112.65%, with RSD less than 12%. The method was successfully applied for use in the mycotoxin analysis of 260 samples. A high percentage (28.46%) of samples were contaminated by 1-5 mycotoxins. Alternariol mono methylether was the predominant mycotoxin with high percentage of positive samples (37.5%), followed by alternariol (22.5%), alternariol (17.5%), tentoxin (10.83%), altertoxin Ⅰ (7.5%), and altenusin (4.17%). Collectively, the natural incidence data obtained from this study will help with better, validated risk assessments and efforts towards more comprehensive, future regulation.

Analytical Methodologies for Lipidomics in Hemp Plant.

The chemical composition of Cannabis sativa L. has been extensively studied for tens of years, but little is known about its lipidome. This chapter describes an analytical workflow for polar lipid determination in hemp. After extraction, lipids are enriched and isolated by graphitized carbon black sorbent, and the isolated lipid is analyzed by liquid chromatography (LC) coupled with high resolution mass spectrometry, leading to identification of many lipid species. We have developed a semi-automated platform using commercially available Lipostar software for lipid identification. Our approach affords the identification of 189 polar lipids in hemp extract, including sulfolipids and phospholipids. The number of the identified lipid species is by far the highest ever reported for Cannabis sativa.

Optimization and validation of a method for the determination of acidic pesticides in cabbage and spinach by modifying QuEChERS procedure and liquid chromatography-tandem mass spectrometry.

A quick, easy, cheap, effective, rugged, and safe (QuEChERS) method was developed and combined with liquid chromatography-tandem mass spectrometry to analyze 12 acidic pesticides in cabbage and spinach. The extraction solvents, phase partition salts and sorbents effect was studied to optimize the method followed by dilution before sample injection. The extraction involved 5% formic acid in acetonitrile, and the liquid-liquid partition was salt-induced. Carbopack Z, a high surface area graphitized carbon black, was a new sorbent used in the clean-up. The results show that Carbopack Z effectively removes interferences with little loss of acidic pesticides. All tested pesticide recoveries were satisfactory when Carbopack Z was combined with C18 in the clean-up at optimized condition. After clean-up, the extract was subjected to 10-fold dilution to sufficiently reduce the matrix effect (<20%). The limit of quantification (LOQ) was 1-5 ng/g, and the mean recovery was between 95 and 110% with a relative standard deviation <20% (between 2% and 10%) for the spiking of three concentrations: 5, 50, and 500 ng/g. The extract was less pigmented in the modified QuEChERS method than its original version. Thus, the modified method is a useful alternative for investigating the acidic pesticide residues in cabbage and spinach.

Extraction Improvement of the Bioactive Blue-Green Pigment "Marennine" from Diatom Haslea ostrearia's Blue Water: A Solid-Phase Method Based on Graphitic Matrices.

The compound "marennine" is a blue-green pigment produced by the benthic microalgae Haslea ostrearia, with pathogenicity reduction activities against some bacteria and promising potential as a natural pigment in seafood industries. After decades of research, the chemical family of this compound still remains unclear, mainly because structural studies were impaired by the presence of co-extracted compounds in marennine isolates. To improve the purity of marennine extract, we developed a novel extraction method using a graphitic stationary phase, which provides various advantages over the previous procedure using tandem ultrafiltration. Our method is faster, more versatile, provides a better crude yield (66%, compared to 57% for ultrafiltration) and is amenable to upscaling with continuous photobioreactor cultivation. Our goal was to take advantage of the modulable surface properties of the graphitic matrix by optimizing its interactions with marennine. As such, the effects of organic modifiers, pH and reducing agents were studied. With this improvement on marennine purification, we achieved altogether the isolation of a fucoidan-related, sulfated polysaccharide from blue water. Characterization of the polysaccharides fraction suggests that roughly half of UV-absorbing compounds could be isolated from the marennine crude extracts. The identification of sulfated polysaccharides could be a major breakthrough for marennine purification, providing targeted isolation techniques. Likewise, the added value of Haslea ostrearia and the role of polysaccharides in previous marennine chemical characterization and bioactivity studies remain to be determined.

Comparison of Accelerated Solvent Extraction (ASE) and Energized Dispersive Guided Extraction (EDGE) for the analysis of pesticides in leaves.

Various techniques have been evaluated for the extraction and cleanup of pesticides from environmental samples. In this work, a Selective Pressurized Liquid Extraction (SPLE) method for pesticides was developed using a Thermo Fisher Scientific Accelerated Solvent Extraction (ASE) system. This instrument was compared to the newly introduced (2017) extraction instrument, the Energized Dispersive Guided Extraction (EDGE) system, which combines Pressurized Liquid Extraction (PLE) and dispersive Solid Phase Extraction (dSPE). We first optimized the SPLE method using the ASE instrument for pesticide extraction from alfalfa leaves using layers of Florisil and graphitized carbon black (GCB) downstream of the leaf homogenate in the extraction cell (Layered ASE method). We then compared results obtained for alfalfa and citrus leaves with the Layered ASE method to those from a method in which the leaf homogenate and sorbents were mixed (Mixed ASE method) and to similar methods modified for use with EDGE (Layered EDGE and Mixed EDGE methods). The ASE and EDGE methods led to clear, colorless extracts with low residual lipid weight. No significant differences in residual lipid masses were observed between the methods. The UV-Vis spectra showed that Florisil removed a significant quantity of the light-absorbing chemicals, but that GCB was required to produce colorless extracts. Recoveries of spiked analytes into leaf homogenates were generally similar among methods, but in several cases, significantly higher recoveries were observed in ASE extracts. Nonetheless, no significant differences were observed among pesticide concentrations in field samples when calculated with the isotope dilution method in which labelled surrogates were added to samples before extraction. The extraction time with the ASE methods was ~45 minutes, which was ~4.5 times longer than with the EDGE methods. The EDGE methods used ~10 mL more solvent than the ASE methods. Based on these results, the EDGE is an acceptable extraction instrument and, for most compounds, the EDGE had a similar extraction efficiency to the ASE methods.

Dispersive liquid-liquid extraction based on magnetic Pickering emulsion followed by gas chromatography-tandem mass spectrometry for the simultaneous determination of aldehydes in environmental water samples.

A dispersive liquid-liquid extraction based on Pickering emulsion stabilized with ferroferric oxide grafted nitrogen-doped graphitized carbon black has been developed to simultaneously determine seven aldehydes in environmental water samples, in combination with pentafluorobenzyl hydroxylamine precolumn derivatization gas chromatography-tandem mass spectrometry. The nitrogen-doped graphitized carbon was prepared from dicyandiamide waste residue with a simple acid wash process. The effects of magnetic emulsifier amount, extraction time, solution pH, and oil/water volume ratio on the formation of magnetically responsive Pickering emulsion and the extraction efficiency of the proposed dispersive liquid-liquid extraction were also investigated. Under the optimized conditions, satisfactory linearities were obtained for all aldehydes with correlation coefficients larger than 0.9984. The limits of detection and quantitation of seven aldehydes were in the range of 17.3-30.1 ng/L and 54.3-103.4 ng/L, respectively, with intra- and interday relative standard deviations less than 8.6%. The mean recoveries at three spiked levels ranged from 70.0 to 101.4%. With the Pickering emulsion as a "minimized extractor", the extraction was accomplished within 5 min. After extraction, the magnetic disperser could be recovered for reuse at least five times by an external magnetic field. The proposed method was demonstrated to be feasible, simple, and economic for the trace analysis of the aldehydes in environmental water samples.

Sorbent-incorporated dipstick for direct assaying of proteases.

Efficient removal of interferents from complex matrices would significantly improve the performance of state of the art dipstick assays. Herein, we evaluate a graphitized carbon black (GCB)-incorporated dipstick, a configuration that has not been explored before, for reliable and facile on-site analysis of complex matrices. Carrot juice, a highly pigmented sample matrix, is chosen for evaluating the retention of interferents within the sorbent-incorporated cleanup pad on the dipstick. A peptide with a specific cleavage site for botulinum neurotoxin A light chain (BoNT/A LC), a model protease for validation of the proposed dipstick assay, is incubated with the test samples containing BoNT/A LC. Subsequently, the BoNT/A LC digested substrate and sample matrix flow vertically through the GCB-deposited cleanup pad within which the matrix interferents are captured, while the substrate, with a minimum of interferents, continues to flow toward a conjugation pad for labelling with Europium particles. Finally, the cleaved and uncleaved substrates flow toward a detection zone, where they bind to the test line producing a pinkish band which is not visible in the absence of GCB incorporation. The dipstick assay yields a LOD of 0.1 nM (5 ng/mL) of BoNT/A LC in carrot juice, within 20 min. The reported approach enables detection of proteases in a wide range of matrices upon incorporation of appropriate sorbents, ultimately aiming to exclude tedious laboratory-based sample pre-treatment protocols. Thus, merging extraction, cleanup, and pre-concentration steps with a sensitive optical detection approach is an attractive strategy for on-site assaying in complex matrices. Graphical abstract.

A clean-up strategy for identification of circulating endogenous short peptides in human plasma by zwitterionic hydrophilic liquid chromatography and untargeted peptidomics identification.

Short peptides, namely di- tri- and tetra peptides, have been proven to play an important diagnostic role in several diseases. Therefore, the development of an analytical approach for their detection and identification is nowadays an important research goal. This paper describes an analytical procedure able to overcome the issues of short peptide isolation, clean-up and identification in plasma samples. Four different protocols were compared and tested to maximize both recovery and total number of identifications of short circulating plasma endogenous peptides. The purified peptides, coming from the four different tested protocols, were separated by zwitterionic hydrophilic liquid chromatography coupled to high-resolution mass spectrometry with the purpose of accomplishing an untargeted investigation based on suspect screening for short peptides in plasma. In particular, the use of Phree™ Phospholipid removal cartridge in combination with a purification step by solid phase extraction on a graphitized carbon black sorbent allowed the identification of the largest number of amino acid sequences (91 short peptides). The clean-up procedure allowed to tackle the issue of the low abundance of such peptides and their suppression during mass-spectrometric analysis. The results indicated that sample preparation is therefore fundamental for short peptide analysis in plasma samples.

New insights in hemp chemical composition: a comprehensive polar lipidome characterization by combining solid phase enrichment, high-resolution mass spectrometry, and cheminformatics.

The chemical composition of Cannabis sativa L. has been extensively investigated for several years; nevertheless, a detailed lipidome characterization is completely lacking in the literature. To achieve this goal, an extraction and enrichment procedure was developed for the characterization of phospholipids and sulfolipids. Firstly, a study on the solid-liquid extraction was performed, to maximize the recovery of the considered lipids; the best procedure consisted of a simple extraction with a mixture of methanol and chloroform (1:1, v/v). The hemp extracts were analyzed by ultra-high-performance liquid chromatography coupled to high-resolution mass spectrometry and lipids were tentatively identified by Lipostar. To improve the number of identifications, an enrichment method, based on graphitized carbon black solid phase extraction, was evaluated to fractionate phospholipids and sulfolipids into separate eluates. Recovery and matrix effects of the procedure were determined on a mixture of standard lipids, containing representative compounds for each considered lipid class. The optimized method allowed the tentative identification of 189 lipids, including 51 phospholipids and 80 sulfolipids, in the first and second fractions, respectively. The detection of only 6 sulfolipids in the first fraction and 9 phospholipids in the second fraction proved the efficacy of the fractionation method, which also allowed the number of lipid identifications to be increased compared to the same procedure without enrichment, which scored 100 lipids. Finally, a semi-quantitative analysis permitted the hemp polar lipidome to be characterized. The results of this study allow knowledge of the hemp chemical composition to be improved with a detailed description of its phospho- and sulfolipid profiles. Graphical abstract.

Phospholipidome of extra virgin olive oil: Development of a solid phase extraction protocol followed by liquid chromatography-high resolution mass spectrometry for its software-assisted identification.

The determination of phospholipids in olive oil is challenging due to their low concentration. For this reason, a comparison of two solid phase extraction procedures, namely weak anionic exchange (WAX) and graphitized carbon black (GCB), is presented for the enrichment of phospholipids. Analyses were performed by liquid chromatography-high resolution mass spectrometry (LC-HRMS) and lipids were identified by Lipostar software. Compared to the WAX solid phase extraction, GCB demonstrated the best performance and provided 82 identified phospholipids vs only 32. The final method was validated for some representative phospholipids, showing good repeatability and recovery (63-101%). High sensitivity was reached, with detection limits in the range 9-36 ng g-1, never reported before for phospholipids in olive oil. A semi-quantitative analysis indicated phosphatidic acids and phosphatidylglycerols as the most abundant species, both in number and concentrations. The GCB-LC-HRMS-Lipostar platform can be successfully applied for a comprehensive polar lipidomic characterization of olive oils.

Enrichment procedure based on graphitized carbon black and liquid chromatography-high resolution mass spectrometry for elucidating sulfolipids composition of microalgae.

Microalgae have recently become a popular functional food due to their health benefits. Sulfolipids, a class of substances abundant in this matrix, have been reported to have interesting bioactivities, such as anti-carcinogenic activity. However, despite the potential interest in sulfolipids, a dedicated analytical method for their characterization is currently lacking but would significantly increase the coverage of sulfolipids with respect to the direct lipidomic analysis. To achieve this goal, in this work a procedure, based on graphitized carbon black solid phase extraction, was developed for clean-up and enrichment of sulfolipids (sulfoquinovosyldiacylglycerols and sulfoquinovosylmonoacylglycerols) and it was applied to spirulina (Arthrospira platensis) microalgae. A careful study of the solid phase extraction conditions was performed, first to maximize the recovery of reference standards, then to increase the total number of identified sulfolipids from the spirulina lipid extract. All samples were analysed by ultra-high performance liquid chromatography coupled to high resolution mass spectrometry and lipids were tentatively identified by Lipostar, for a reliable lipid structure assignment. The developed method was compared to the direct lipidomic analysis without enrichment, to establish the enrichment efficiency in terms of number of identifications. From the comparison, the enrichment procedure proved better and allowed the tentative identification of 199 sulfolipids, which is the largest number reported so far for the Arthrospira platensis species. The described method was validated in terms of precision, accuracy, recovery, limit of quantitation and detection for two sulfolipids. Finally, a relative lipid quantitation based on peak area was carried out on the microalgae sample, which indicated nine abundant sulfolipids as representing ca. 60% of sulfolipids in spirulina microalgae.

Carbon-based sorbents and their nanocomposites for the enrichment of heavy metal ions: a review.

This review (with 168 refs) summarizes the progress that has been made on the field of microextraction of heavy metal ions using carbonaceous materials. Following an introduction into the features of such materials, we discuss the various kinds of sorption-based microextraction techniques (like solid phase extraction, micro solid phase extraction, solid phase microextraction, magnetic solid phase extraction, and dispersive solid phase extraction). The next section covers specific methods based on the use of carbon-based adsorbents (with subsections on uses of carbon nanotubes, graphene, fullerenes, activated carbon, carbon nanohorns, carbon nanofibers, graphitic carbon nitride, and their composites). The concluding section addresses current challenges, and gives an outlook on potential future trends. Graphical abstract Schematic of the variety of applications of carbonaceous sorbents in sorptive extraction methods including SPE, SPME, SBSE, DSPE, µSPE, D-µSPE, and MSPE for the extraction and enrichment of different heavy metals.

Application of high-surface-area graphitized carbon black with primary secondary amine as an alternative quick, easy, cheap, effective, rugged, and safe cleanup material for pesticide multi-residue analysis in spinach.

A multi-residue method has been developed and validated to determine 46 pesticides in spinach using liquid chromatography tandem mass spectrometry. The method is based on modified quick, easy, cheap, effective, rugged, and safe sample preparation, where high-surface-area graphitized carbon black was used first as sorbent material in the dispersive solid-phase extraction. The method was compared with the quick, easy, cheap, effective, rugged, and safe method. The morphology, surface area, pore size, and pore volume of the sorbent was determined. The results obtained show that the sorbent consists of high surface area (233 m2 /g) and large pore volume (1.5 cm3 /g). The calibration curve correlation coefficient (R2 ) of the method was at least 0.99. The average recoveries ranged from 74 to 116%, and limits of detection and quantification from 0.0001 to 0.002 mg/kg and from 0.0002 to 0.005 mg/kg, respectively. Using the method, the pesticides exhibited low matrix effect (< 20%), except for nicosulfuron (29.86%), methomyl (26.77%), and flufenoxuron (24.65%). The method showed better potential to remove pigments than the quick, easy, cheap, effective, rugged, and safe method. It is demonstrated that the proposed method could be useful alternative for sample preparation of spinach and other matrices in future.

A new carbon-based magnetic material for the dispersive solid-phase extraction of UV filters from water samples before liquid chromatography-tandem mass spectrometry analysis.

Magnetic solid-phase extraction is one of the most promising new extraction methods for liquid samples before ultra-high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) analysis. Several types of materials, including carbonaceous ones, have been prepared for this purpose. In this paper, for the first time, the preparation, characterization, and sorption capability of Fe3O4-graphitized carbon black (mGCB) composite toward some compounds of environmental interest were investigated. The synthesized mGCB consisted of micrometric GCB particles with 55 m2 g-1 surface area bearing some carbonyl and hydroxyl functionalities and the surface partially decorated by Fe3O4 microparticles. The prepared mGCB was firstly tested as an adsorbent for the extraction from surface water of 50 pollutants, including estrogens, perfluoroalkyl compounds, UV filters, and quinolones. The material showed good affinity to many of the tested compounds, except carboxylates and glucoronates; however, some compounds were difficult to desorb. Ten UV filters belonging to the chemical classes of benzophenones and p-aminobenzoates were selected, and parameters were optimized for the extraction of these compounds from surface water before UHPLC-MS/MS determination. Then, the method was validated in terms of linearity, trueness, intra-laboratory precision, and detection and quantification limits. In summary, the method performance (trueness, expressed as analytical recovery, 85-114%; RSD 5-15%) appears suitable for the determination of the selected compounds at the level of 10-100 ng L-1, with detection limits in the range of 1-5 ng L-1. Finally, the new method was compared with a published one, based on conventional solid-phase extraction with GCB, showing similar performance in real sample analysis. Graphical Abstract Workflow of the analytical method based on magnetic solid-phase extraction followed by LC-MS/MS determination.

A Rapid Magnetic Solid Phase Extraction Method Followed by Liquid Chromatography-Tandem Mass Spectrometry Analysis for the Determination of Mycotoxins in Cereals.

Mycotoxins can contaminate various food commodities, including cereals. Moreover, mycotoxins of different classes can co-contaminate food, increasing human health risk. Several analytical methods have been published in the literature dealing with mycotoxins determination in cereals. Nevertheless, in the present work, the aim was to propose an easy and effective system for the extraction of six of the main mycotoxins from corn meal and durum wheat flour, i.e., the main four aflatoxins, ochratoxin A, and the mycoestrogen zearalenone. The developed method exploited magnetic solid phase extraction (SPE), a technique that is attracting an increasing interest as an alternative to classical SPE. Therefore, the use of magnetic graphitized carbon black as a suitable extracting material was tested. The same magnetic material proved to be effective in the extraction of mycoestrogens from milk, but has never been applied to complex matrices as cereals. Ultra high-performance liquid chromatography tandem mass spectrometry was used for detection. Recoveries were >60% in both cereals, even if the matrix effects were not negligible. The limits of quantification of the method results were comparable to those obtained by other two magnetic SPE-based methods applied to cereals, which were limited to one or two mycotoxins, whereas in this work the investigated mycotoxins belonged to three different chemical classes.

An efficient cleanup method coupled with gas chromatography and mass spectrometry for multi-pesticides residue analysis in complex plant matrices.

We aimed to develop an efficient cleanup method for multi-pesticides residue analysis in complex plant matrices, shallot, ginger, garlic, onion, leek, and celery. Column chromatography was used as the cleanup method and fabricated with florisil and graphitized carbon black as the adsorbents. The amount of the graphitized carbon black adsorbent and the choice of the elution solvent were systematically investigated for exploring the best combination. The target pesticides covered organochlorine, pyrethroid, and organophosphorus pesticides, and were 38 in total. The method validation and comparison were performed to verify its feasibility and advantages in operation convenience and purification efficiency. The method limit of quantitation varied from 0.01 to 0.03 mg/kg, which depends on the pesticides and the sample matrices. The recoveries of the pesticides ranged from 60.5 to 128% (RSD ≤ 19.0%) at the spiked concentration level of 0.01 (or 0.03) mg/kg and 62.9 to 130% (RSD ≤ 13.0%) at 0.1 mg/kg. Compared with the commercial cleanup solid-phase extraction cartridges, the present adsorbent combination displayed better purification effect and shorter sample pretreatment time, demonstrating potential application prospect in the complex matrix sample analysis.

Determination of aniline and quinoline compounds in textiles.

A simple method for simultaneous determination of twenty-one analytes, belonging to two classes of compounds, aromatic amines and quinolines, is presented. Several of the analytes considered in this study frequently occur in textiles goods on the open market and have been related to allergic contact dermatitis and/or are proven or suspected carcinogens. The method includes an efficient clean-up step using graphitized carbon black (GCB) that simplifies and improves the robustness of the subsequent GC-MS analysis. Briefly, after solvent extraction of the textile sample, the extract is passed through a GCB SPE cartridge that selectively retain dyes and other interfering compounds present in the matrix, producing a clean extract, suitable for GC-MS analysis, is obtained. The method was evaluated by spiking blank textiles with the selected analytes. Method quantification limits (MQL) ranged from 5 to 720ng/g depending on the analyte. The linear range of the calibration curves ranged over two order magnitude with coefficients of determination (R2) higher than 0.99. Recoveries ranged from 70 to 92% with RSDs 1.7-14%. The effectiveness of the method was tested on a variety of textile materials samples from different origin. In a pilot explorative survey, 2,6-dichloro-4-nitroaniline was detected in all the analysed clothing samples in concentrations ranging from 1.0 to 576µg/g. 2,4-dinitroaniline was detected in four of the seven samples with a highest concentration of 305µg/g. Quinoline was detected in all samples in concentrations ranging from 0.06 to 6.2µg/g.