Dynamic Deformation in Nuclear Graphite and Underlying Mechanisms.

Time-dependent deformation in nuclear graphite is influenced by the creation and migration of radiation-induced defects in the reactor environment. This study investigates the role of pre-existing defects such as point defect clusters and Mrozowski cracks in nuclear graphite IG-110. Separate specimens were irradiated with a 2.8 MeV Au2+ beam with a fluence of 4.38 × 1014 cm-2 and an 8 MeV C2+ beam with a fluence of 1.24 × 1016 cm-2. Microscopic specimens were either mechanically loaded inside a transmission electron microscope (TEM) or subjected to ex situ indentation-based creep loading. In situ TEM tests showed significant plasticity in regions highly localized around the Mrozowski cracks, resembling slip or ripplocation bands. Slip bands were also seen near regions without pre-existing defects but at very high stresses. Ex situ self-ion irradiation embrittled the specimens and decreased the creep displacement and rate, while heavy ion irradiation resulted in the opposite behavior. We hypothesize that the large-sized gold ions (compared to the carbon atoms) induced interplanar swelling as well as cross-plane channels for increased defect mobility. These findings illustrate the role of pre-existing defects in the dynamic relaxation of stresses during irradiation and the need for more studies into the radiation environment's impact on the mechanical response of nuclear graphite.

Unraveling the adsorption-limited hydrogen oxidation reaction at palladium surface via in situ electron microscopy.

Palladium (Pd) catalysts have been extensively studied for the direct synthesis of H2O through the hydrogen oxidation reaction at ambient conditions. This heterogeneous catalytic reaction not only holds considerable practical significance but also serves as a classical model for investigating fundamental mechanisms, including adsorption and reactions between adsorbates. Nonetheless, the governing mechanisms and kinetics of its intermediate reaction stages under varying gas conditions remain elusive. This is attributed to the intricate interplay between adsorption, atomic diffusion, and concurrent phase transformation of catalyst. Herein, the Pd-catalyzed, water-forming hydrogen oxidation is studied in situ, to investigate intermediate reaction stages via gas cell transmission electron microscopy. The dynamic behaviors of water generation, associated with reversible palladium hydride formation, are captured in real time with a nanoscale spatial resolution. Our findings suggest that the hydrogen oxidation rate catalyzed by Pd is significantly affected by the sequence in which gases are introduced. Through direct evidence of electron diffraction and density functional theory calculation, we demonstrate that the hydrogen oxidation rate is limited by precursors' adsorption. These nanoscale insights help identify the optimal reaction conditions for Pd-catalyzed hydrogen oxidation, which has substantial implications for water production technologies. The developed understanding also advocates a broader exploration of analogous mechanisms in other metal-catalyzed reactions.

Imaging Dissolution Dynamics of Individual NaCl Nanoparticles during Deliquescence with In Situ Transmission Electron Microscopy.

Water vapor condensation on hygroscopic aerosol particles plays an important role in cloud formation, climate change, secondary aerosol formation, and aerosol aging. Conventional understanding considers deliquescence of nanosized hygroscopic aerosol particles a nearly instantaneous solid to liquid phase transition. However, the nanoscale dynamics of water condensation and aerosol particle dissolution prior to and during deliquescence remain obscure due to a lack of high spatial and temporal resolution single particle measurements. Here we use real time in situ transmission electron microscopy (TEM) imaging of individual sodium chloride (NaCl) nanoparticles to demonstrate that water adsorption and aerosol particle dissolution prior to and during deliquescence is a multistep dynamic process. Water condensation and aerosol particle dissolution was investigated for lab generated NaCl aerosols and found to occur in three distinct stages as a function of increasing relative humidity (RH). First, a < 100 nm water layer adsorbed on the NaCl cubes and caused sharp corners to dissolve and truncate. The water layer grew to several hundred nanometers with increasing RH and was rapidly saturated with solute, as evidenced by halting of particle dissolution. Adjacent cube corners displayed second-scale curvature fluctuations with no net particle dissolution or water layer thickness change. We propose that droplet solute concentration fluctuations drove NaCl transport from regions of high local curvature to regions of low curvature. Finally, we observed coexistence of a liquid water droplet and aerosol particle immediately prior to deliquescence. Particles dissolved discretely along single crystallographic directions, separated by few second lag times with no dissolution. This work demonstrates that deliquescence of simple pure salt particles with sizes in the range of 100 nm to several microns is not an instantaneous phase transition and instead involves a range of complex dissolution and water condensation dynamics.

Uncovering Atomic Migrations Behind Magnetic Tunnel Junction Breakdown.

As advances in computing technology increase demand for efficient data storage solutions, spintronic magnetic tunnel junction (MTJ)-based magnetic random-access memory (MRAM) devices emerge as promising alternatives to traditional charge-based memory devices. Successful applications of such spintronic devices necessitate understanding not only their ideal working principles but also their breakdown mechanisms. Employing an in situ electrical biasing system, atomic-resolution scanning transmission electron microscopy (STEM) reveals two distinct breakdown mechanisms. Soft breakdown occurs at relatively low electric currents due to electromigration, wherein restructuring of MTJ core layers forms ultrathin regions in the dielectric MgO layer and edge conducting paths, reducing device resistance. Complete breakdown occurs at relatively high electric currents due to a combination of joule heating and electromigration, melting MTJ component layers at temperatures below their bulk melting points. Time-resolved, atomic-scale STEM studies of functional devices provide insight into the evolution of structure and composition during device operation, serving as an innovative experimental approach for a wide variety of electronic devices.

3D-Printed Hierarchically Microgrid Frameworks of Sodiophilic Co3O4@C/rGO Nanosheets for Ultralong Cyclic Sodium Metal Batteries.

Herein, hierarchically structured microgrid frameworks of Co3O4 and carbon composite deposited on reduced graphene oxide (Co3O4@C/rGO) are demonstrated through the three-dimensioinal (3D) printing method, where the porous structure is controllable and the height and width are scalable, for dendrite-free Na metal deposition. The sodiophilicity, facile Na metal deposition kinetics, and NaF-rich solid electrolyte interphase (SEI) formation of cubic Co3O4 phase are confirmed by combined spectroscopic and computational analyses. Moreover, the uniform and reversible Na plating/stripping process on 3D-printed Co3O4@C/rGO host is monitored in real time using in situ transmission electron and optical microscopies. In symmetric cells, the 3D printed Co3O4@C/rGO electrode achieves a long-term stability over 3950 at 1 mA cm-2 and 1 mAh cm-2 with a superior Coulombic efficiency (CE) of 99.87% as well as 120 h even at 20 mA cm-2 and 20 mAh cm-2, far exceeding the previously reported carbon-based hosts for Na metal anodes. Consequently, the full cells of 3D-printed Na@Co3O4@C/rGO anode with 3D-printed Na3V2(PO4)3@C-rGO cathode (≈15.7 mg cm-2) deliver the high specific capacity of 97.97 mAh g-1 after 500 cycles with a high CE of 99.89% at 0.5 C, demonstrating the real operation of flexible Na metal batteries.

In Situ Lattice-Resolution Revelation of the Origins of Unexplored Anisotropic Sodiation Kinetics and Phase Transition in the Niobium Sulfide Anode.

Layered transition metal dichalcogenides (TMDs) have exhibited huge potential as anode materials for sodium-ion batteries. Most of them usually store sodium via an intercalation-conversion mechanism, but niobium sulfide (NbS2) may be an exception. Herein, through in situ transmission electron microscopy, we carefully investigated the insertion behaviors of Na ions in NbS2 and directly visualized anisotropic sodiation kinetics. Lattice-resolution imaging coupled with density functional theory calculations reveals the preferential diffusion of Na ions within layers of NbS2, accompanied by observable interlayer lattice expansion. Impressively, the Na-inserted layers can still withstand in situ mechanical testing. Further in situ observation vertical to the a/b plane of NbS2 tracked the illusive conversion reaction, which could result from interlayer gliding or wrinkling associated with stress accumulation. In situ electron diffraction measurements ruled out the possibility of such a conversion mechanism and identified a phase transition from pristine 3R-NbS2 to 2H-NaNbS2. Therefore, the NbS2 anode stores Na ions via only the intercalation mechanism, which conceptually differs from the well-known intercalation-conversion mechanism of typical TMDs. These findings not only decipher the whole sodiation process of the NbS2 anode but also provide valuable reference for unraveling the precise sodium storage mechanism in other TMDs.

Interrogation of 3d Transition Bimetallic Nanocrystal Nucleation and Growth Using In Situ Electron Microscope and Synchrotron X-ray Techniques.

Understanding the nucleation and growth mechanism of 3d transition bimetallic nanocrystals (NCs) is crucial to developing NCs with tailored nanostructures and properties. However, it remains a significant challenge due to the complexity of 3d bimetallic NCs formation and their sensitivity to oxygen. Here, by combining in situ electron microscopy and synchrotron X-ray techniques, we elucidate the nucleation and growth pathways of Fe-Ni NCs. Interestingly, the formation of Fe-Ni NCs emerges from the assimilation of Fe into Ni clusters together with the reduction of Fe-Ni oxides. Subsequently, these NCs undergo solid-state phase transitions, resulting in two distinct solid solutions, ultimately dominated by γ-Fe3Ni2. Furthermore, we deconvolve the interplays between local coordination and electronic state concerning the growth temperature. We directly visualize the oxidation-state distributions of Fe and Ni at the nanoscale and investigate their changes. This work may reshape and enhance the understanding of nucleation and growth in atomic crystallization.

Nanoscale Adhesion and Material Transfer at 2D MoS2-MoS2 Interfaces Elucidated by In Situ Transmission Electron Microscopy and Atomistic Simulations.

Low-dimensional materials, such as MoS2, hold promise for use in a host of emerging applications, including flexible, wearable sensors due to their unique electrical, thermal, optical, mechanical, and tribological properties. The implementation of such devices requires an understanding of adhesive phenomena at the interfaces between these materials. Here, we describe combined nanoscale in situ transmission electron microscopy (TEM)/atomic force microscopy (AFM) experiments and simulations measuring the work of adhesion (Wadh) between self-mated contacts of ultrathin nominally amorphous and nanocrystalline MoS2 films deposited on Si scanning probe tips. A customized TEM/AFM nanoindenter permitted high-resolution imaging and force measurements in situ. The Wadh values for nanocrystalline and nominally amorphous MoS2 were 604 ± 323 mJ/m2 and 932 ± 647 mJ/m2, respectively, significantly higher than previously reported values for mechanically exfoliated MoS2 single crystals. Closely matched molecular dynamics (MD) simulations show that these high values can be explained by bonding between the opposing surfaces at defects such as grain boundaries. Simulations show that as grain size decreases, the number of bonds formed, the Wadh and its variability all increase, further supporting that interfacial covalent bond formation causes high adhesion. In some cases, sliding between delaminated MoS2 flakes during separation is observed, which further increases the Wadh and the range of adhesive interaction. These results indicate that for low adhesion, the MoS2 grains should be large relative to the contact area to limit the opportunity for bonding, whereas small grains may be beneficial, where high adhesion is needed to prevent device delamination in flexible systems.

In Situ TEM Tracking of Disconnection Motion and Atomic Cooperative Reorientation in the Oriented Attachment of Pt Nanoparticles.

The oriented attachment (OA) of nanoparticles (NPs) is an important crystal growth mechanism in many materials. However, a comprehensive understanding of the atomic-scale alignment and attachment processes is still lacking. We conducted in situ atomic resolution studies using high-resolution transmission electron microscopy to reveal how two Pt NPs coalesce into a single particle via OA, which involves the formation of atomic-scale links and a grain boundary (GB) between the NPs, as well as GB migration. Density functional theory calculations showed that the system energy changes as a function of the number of disconnections during the coalescence process. Additionally, the formation and annihilation processes of disconnection are always accompanied by the cooperative reorientation motion of atoms. These results further elucidate the growth mechanism of OA at the atomic scale, providing microscopic insights into OA dynamics and a framework for the development of processing strategies for nanocrystalline materials.

An in-situ magnetising holder achieving 1.5 T in-plane field in 200 kV transmission electron microscope.

A strong in-plane magnetic field is required for Lorentz transmission electron microscopy (LTEM) to observe the evolution of the magnetic domain structure of materials with high coercivity, particularly for research on rare-earth permanent magnets. However, the maximum field of the present in-situ magnetising holder applied in 200-kV or 300-kV TEM does not exceed 0.1 T. In this study, the reason for the low field was analysed, and the field strength was significantly elevated by reducing the field application area of the field generator. From finite element method calculations and experimental measurements, a 1.5 T in-plane field was achieved by our new holder in a 200-kV TEM, and images with good quality could still be obtained. Using the newly developed holder, the magnetisation process of hot-pressed NdFeB magnets was observed. The in-situ magnetising holder can be used in research on a wide variety of magnetic materials.

Real-Time TEM Observation of the Role of Defects on Nickel Silicide Propagation in Silicon Nanowires.

Metal silicides have received significant attention due to their high process compatibility, low resistivity, and structural stability. In nanowire (NW) form, they have been widely prepared using metal diffusion into preformed Si NWs, enabling compositionally controlled high-quality metal silicide nanostructures. However, unlocking the full potential of metal silicide NWs for next-generation nanodevices requires an increased level of mechanistic understanding of this diffusion-driven transformation. Herein, using in situ transmission electron microscopy (TEM), we investigated the defect-controlled silicide formation dynamics in one-dimensional NWs. A solution-based synthetic route was developed to form Si NWs anchored to Ni NW stems as an optimal platform for in situ TEM studies of metal silicide formation. Multiple in situ annealing experiments led to Ni diffusion from the Ni NW stem into the Si NW, forming a nickel silicide. We observed the dynamics of Ni propagation in straight and kinked Si NWs, with some regions of the NWs acting as Ni sinks. In NWs with high defect distribution, we obtained direct evidence of nonuniform Ni diffusion and silicide retardation. The findings of this study provide insights into metal diffusion and silicide formation in complex NW structures, which are crucial from fundamental and application perspectives.

Support-Based Transfer and Contacting of Individual Nanomaterials for In Situ Nanoscale Investigations.

Although in situ transmission electron microscopy (TEM) of nanomaterials has been gaining importance in recent years, difficulties in sample preparation have limited the number of studies on electrical properties. Here, a support-based preparation method of individual 1D and 2D materials is presented, which yields a reproducible sample transfer for electrical investigation by in situ TEM. A mechanically rigid support grid facilitates the transfer and contacting to in situ chips by focused ion beam with minimum damage and contamination. The transfer quality is assessed by exemplary specimens of different nanomaterials, including a monolayer of WS2 . Possible studies concern the interplay between structural properties and electrical characteristics on the individual nanomaterial level as well as failure analysis under electrical current or studies of electromigration, Joule heating, and related effects. The TEM measurements can be enriched by additional correlative microscopy and spectroscopy carried out on the identical object with techniques that allow a characterization with a spatial resolution in the range of a few microns. Although developed for in situ TEM, the present transfer method is also applicable to transferring nanomaterials to similar chips for performing further studies or even for using them in potential electrical/optoelectronic/sensing devices.

Real-Time Observation of Nanoscale Kink Band Mediated Plasticity in Ion-Irradiated Graphite: An In Situ TEM Study.

Graphite IG-110 is a synthetic polycrystalline material used as a neutron moderator in reactors. Graphite is inherently brittle and is known to exhibit a further increase in brittleness due to radiation damage at room temperature. To understand the irradiation effects on pre-existing defects and their overall influence on external load, micropillar compression tests were performed using in situ nanoindentation in the Transmission Electron Microscopy (TEM) for both pristine and ion-irradiated samples. While pristine specimens showed brittle and subsequent catastrophic failure, the 2.8 MeV Au2+ ion (fluence of 4.378 × 1014 cm-2) irradiated specimens sustained extensive plasticity at room temperature without failure. In situ TEM characterization showed nucleation of nanoscale kink band structures at numerous sites, where the localized plasticity appeared to close the defects and cracks while allowing large average strain. We propose that compressive mechanical stress due to dimensional change during ion irradiation transforms buckled basal layers in graphite into kink bands. The externally applied load during the micropillar tests proliferates the nucleation and motion of kink bands to accommodate the large plastic strain. The inherent non-uniformity of graphite microstructure promotes such strain localization, making kink bands the predominant mechanism behind unprecedented toughness in an otherwise brittle material.

In Situ Transmission Electron Microscopy Methods for Lithium-Ion Batteries.

In situ Transmission Electron Microscopy (TEM) stands as an invaluable instrument for the real-time examination of the structural changes in materials. It features ultrahigh spatial resolution and powerful analytical capability, making it significantly versatile across diverse fields. Particularly in the realm of Lithium-Ion Batteries (LIBs), in situ TEM is extensively utilized for real-time analysis of phase transitions, degradation mechanisms, and the lithiation process during charging and discharging. This review aims to provide an overview of the latest advancements in in situ TEM applications for LIBs. Additionally, it compares the suitability and effectiveness of two techniques: the open cell technique and the liquid cell technique. The technical aspects of both the open cell and liquid cell techniques are introduced, followed by a comparison of their applications in cathodes, anodes, solid electrolyte interphase (SEI) formation, and lithium dendrite growth in LIBs. Lastly, the review concludes by stimulating discussions on possible future research trajectories that hold potential to expedite the progression of battery technology.

Atomic-Scale In Situ Observations of Reversible Phase Transformation Assisted Twinning in a CrCoNi Medium-Entropy Alloy.

Twinning is an important deformation mode of face-centered-cubic (FCC) medium- and high-entropy alloys, especially under extreme loading conditions. However, the twinning mechanism in these alloys that have a low or even negative stacking fault energy remains debated. Here, we report atomic-scale in situ observations of the deformation process of a prototypical CrCoNi medium-entropy alloy under tension. We found that the parent FCC phase first transforms into a hexagonal close-packed (HCP) phase through Shockley partial dislocations slipping on the alternate {111} planes. Subsequently, the HCP phase rapidly changes to an FCC twin band. Such reversible phase transformation assisted twinning is greatly promoted by external tensile loads, as elucidated by geometric phase analysis. These results indicate the previously underestimated role of the metastable HCP phase in nanotwin nucleation and early plastic deformations of CrCoNi alloys and shed light on microstructure regulation of medium-entropy alloys with enhanced mechanical properties.

Texture Transfer in Dielectric Layers via Nanocrystalline Networks: Insights from in Situ 4D-STEM.

Transition metal oxide dielectric layers have emerged as promising candidates for various relevant applications, such as supercapacitors or memory applications. However, the performance and reliability of these devices can critically depend on their microstructure, which can be strongly influenced by thermal processing and substrate-induced strain. To gain a more in-depth understanding of the microstructural changes, we conducted in situ transmission electron microscopy (TEM) studies of amorphous HfO2 dielectric layers grown on highly textured (111) substrates. Our results indicate that the minimum required phase transition temperature is 180 °C and that the developed crystallinity is affected by texture transfer. Using in situ TEM and 4D-STEM can provide valuable insights into the fundamental mechanisms underlying the microstructural evolution of dielectric layers and could pave the way for the development of more reliable and efficient devices for future applications.

Nanoscale Cathodoluminescence Thermometry with a Lanthanide-Doped Heavy-Metal Oxide in Transmission Electron Microscopy.

When navigated by the available energy of a system, often provided in the form of heat, physical processes or chemical reactions fleet on a free-energy landscape, thus changing the structure. In in situ transmission electron microscopy (TEM), where material structures are measured and manipulated inside the microscope while being subjected to external stimuli such as electrical fields, laser irradiation, or mechanical stress, it is necessary to precisely determine the local temperature of the specimen to provide a comprehensive understanding of material behavior and to establish the relationship among energy, structure, and properties at the nanoscale. Here, we propose using cathodoluminescence (CL) spectroscopy in TEM for in situ measurement of the local temperature. Gadolinium oxide particles doped with emissive europium ions present an opportunity to utilize them as a temperature probe in CL measurements via a ratiometric approach. We show the thermometric performance of the probe and demonstrate a precision of ±5 K in the temperature range from 113 to 323 K with the spatial resolution limited by the size of the particles, which surpasses other methods for temperature determination. With the CL-based thermometry, we further demonstrate measuring local temperature under laser irradiation.

Resolving the Origins of Superior Cycling Performance of Antimony Anode in Sodium-ion Batteries: A Comparison with Lithium-ion Batteries.

Alloying-type antimony (Sb) with high theoretical capacity is a promising anode candidate for both lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs). Given the larger radius of Na+ (1.02 Å) than Li+ (0.76 Å), it was generally believed that the Sb anode would experience even worse capacity degradation in SIBs due to more substantial volumetric variations during cycling when compared to LIBs. However, the Sb anode in SIBs unexpectedly exhibited both better electrochemical and structural stability than in LIBs, and the mechanistic reasons that underlie this performance discrepancy remain undiscovered. Here, using substantial in situ transmission electron microscopy, X-ray diffraction, and Raman techniques complemented by theoretical simulations, we explicitly reveal that compared to the lithiation/delithiation process, sodiation/desodiation process of Sb anode displays a previously unexplored two-stage alloying/dealloying mechanism with polycrystalline and amorphous phases as the intermediates featuring improved resilience to mechanical damage, contributing to superior cycling stability in SIBs. Additionally, the better mechanical properties and weaker atomic interaction of Na-Sb alloys than Li-Sb alloys favor enabling mitigated mechanical stress, accounting for enhanced structural stability as unveiled by theoretical simulations. Our finding delineates the mechanistic origins of enhanced cycling stability of Sb anode in SIBs with potential implications for other large-volume-change electrode materials.

Reversible MnO to Mn3 O4 Oxidation in Manganese Oxide Nanoparticles.

Manganese is an attractive element for sustainable solutions. It is largely available in the earth's crust, making it ideal for cost-effective and large-scale applications. Especially MnO nanoparticles have recently received attention for applications in battery technology. However, manganese has many oxidation states that are energetically very similar, indicating that they may easily transform from one to the other. Herein, the reversible oxidation of MnO nanoparticles to Mn3 O4 studied with in situ transmission electron microscopy is shown. The oxygen sublattices of MnO and Mn3 O4 are found to be perfectly aligned, and an atomic mechanism where the transformation is facilitated by the migration of Mn cations on the shared O sublattice is proposed. Even when protected with an amorphous carbon layer, MnO particles are highly unstable and oxidize to Mn3 O4 in ethanol. The poor stability of MnO lacks discussion in many battery-related works, and strategies aimed at avoiding this should be developed.

In-situ TEM study from the perspective of holders.

During the in situ transmission electron microscopy (TEM) observations, the diverse functionalities of different specimen holders play a crucial role. We hereby provide a comprehensive overview of the main types of holders, associated technologies and case studies pertaining to the widely employed heating and gas heating methods, from their initial developments to the latest advancement. In addition to the conventional approaches, we also discuss the emergence of holders that incorporate a micro-electro-mechanical system (MEMS) chip for in situ observations. The MEMS technology offers a multitude of functions within a single chip, thereby enhancing the capabilities and versatility of the holders. MEMS chips have been utilized in environmental-cell designs, enabling customized fabrication of diverse shapes. This innovation has facilitated their application in conducting in situ observations within gas and liquid environments, particularly in the investigation of catalytic and battery reactions. We summarize recent noteworthy studies conducted using in situ liquid TEM. These studies highlight significant advancements and provide valuable insights into the utilization of MEMS chips in environmental-cells, as well as the expanding capabilities of in situ liquid TEM in various research domains.