ABSTRACT
The synthesis of groupâ IV metallocene precatalysts for the polymerization of propylene generally yields two different isomers: The racemic isomer that produces isotactic polypropylene (iPP) and the meso isomer that produces atactic polypropylene (aPP). Due to its poor physical properties, aPP has very limited applications. To avoid obtaining blends of both polymers and thus diminish the mechanical and thermal properties of iPP, the meso metallocene complexes need to be separated from the racemic ones tediously-rendering the metallocene-based polymerization of propylene industrially far less attractive than the Ziegler/Natta process. To overcome this issue, we established an isomerization protocol to convert meso metallocene complexes into their racemic counterparts. This protocol increased the yield of iPP by 400 % while maintaining the polymer's excellent physical properties and was applicable to both hafnocene and zirconocene complexes, as well as different precatalyst activation methods. Through targeted variation of the ligand frameworks, methoxy groups at the indenyl moieties were found to be the structural motifs responsible for an isomerization to take place-this experimental evidence was confirmed by density functional theory calculations. Liquid injection field desorption ionization mass spectrometry, as well as 1H and 29Si nuclear magnetic resonance studies, allowed the proposal of an isomerization mechanism.
ABSTRACT
The various steps in the mechanism of olefin polymerizations mediated by neutral rare-earth metallocene complexes are discussed. The complexes are either trivalent hydride and alkyl rare-earth compounds or divalent metallocenes that are activated by the monomer via an oxidation step. The stereospecific polymerizations of conjugated dienes based on the association of a cationic metallocene complex and an alkylaluminum and the polymerization mechanism based on monomer insertion into an aluminum-carbon bond are also discussed. The exploitation of metallocene complexes for the copolymerization of olefins with conjugated dienes is the subject of a third part of this review. The synthesis of new elastomers called ethylene butadiene rubber (EBR) is highlighted. Finally, the use of rare-earth metallocenes in macromolecular engineering is detailed. This includes the synthesis of functional polyolefins and block copolymers including thermoplastic elastomers.
ABSTRACT
Biradicals are important intermediates in the formation and breaking of a chemical bond. Their use as molecular switches is of particular interest. Much less is known about tetraradicals, which can, for example, consist of two biradical(oid) units. Here we report the synthesis of the first persistent phosphorus-centred tetraradical bound to a transition metal fragment. Starting from a zirconocene complex, rac-(ebthi)ZrCl2 (rac-(ebthi) = 1,2-ethylene-1,10-bis(h5-tetrahydroin-denyl), two cyclo-1,3-diphospha-pentane-1,3-diyls were successfully introduced, which finally led to the isolation of a deep green zircon-cene-bridged bis(biradicaloid) complex (5) that can act as a double molecular switch. Under the influence of light (570 nm), this tetra-radical forms a transannular bond in each of the two five-membered biradical units, leading to the formation of housane 5h. Upon irradiation at 415 nm, the reverse reaction is observed, fully reco-vering tetraradical 5. Through single-crystal-to-single-crystal trans-formation, both stable species of the molecular switch could be structurally characterised using SCXRD. The switching under the influence of light and the activation of molecular hydrogen were analysed in solution using NMR and UV spectroscopy. It was found that the addition of one or two equivalents of molecular hydrogen can be switched on and off by light.
ABSTRACT
The stable ferrocene-based N-heterocyclic silylenes fc[(N{B})2Si] (A; fc=1,1'-ferrocenylene, {B}=(HCNDipp)2B, Dipp=2,6-diisopropylphenyl) and fc[(NDipp)2Si] (B) are compared in a study focussing on their reactivity towards a range of small to moderately sized molecular substrates, viz. P4, S8, Se8, MesN3 (Mes=mesityl), RC≡CH, and RC≡CR (R=Ph, SiMe3). The Dipp-substituted congener B exhibits a more pronounced ambiphilicity and is sterically less congested than its 1,3,2-diazaborolyl-substituted relative A, in line with the higher reactivity of the former. The difference in reactivity is obviously due more to electronic than to steric reasons, as is illustrated by the fact that both A and B react with the comparatively bulky substrate MesN3 under mild conditions to afford the corresponding silanimine fc[(N{B})2Si=NMes] and fc[(NDipp)2Si=NMes], respectively. The heavier ketone analogues fc[(N{B})2Si=E] (E=S, Se, Te) are readily available from A and the corresponding chalcogen. In contrast, the reaction of the more reactive silylene B with elemental sulfur or selenium is unspecific, affording product mixtures. However, fc[(NDipp)2Si=Se] is selectively prepared from B and (Et2N)3PSe; the Te analogue is also accessible, but crystallises as head-to-tail dimer.
ABSTRACT
The synthesis of group 4 metal 1-metallacyclobuta-2,3-dienes as organometallic analogues of elusive 1,2-cyclobutadiene has so far been limited to SiMe3 substituted examples. We present the synthesis of two Ph substituted dilithiated ligand precursors for the preparation of four new 1-metallacyclobuta-2,3-dienes [rac-(ebthi)M] (M=Ti, Zr; ebthi=1,2-ethylene-1,10-bis(η5-tetrahydroindenyl)). The organolithium compounds [Li2(RC3Ph)] (1 b: R=Ph, 1 c: R=SiMe3) as well as the metallacycles of the general formula [rac-(ebthi)M(R1C3R2)] (2 b: M=Ti, R1=R2=Ph, 2 c: M=Ti, R1=Ph, R2=SiMe3; 3 b: M=Zr, R1=R2=Ph; 3 c: M=Zr, R1=Ph, R2=SiMe3) were fully characterised. Single crystal X-ray diffraction and quantum chemical bond analysis of the Ti and Zr complexes reveal ligand influence on the biradicaloid character of the titanocene complexes. X-band EPR spectroscopy of structurally similar Ti complexes [rac-(ebthi)Ti(Me3SiC3SiMe3)] (2 a), 2 b, and 2 c was carried out to evaluate the accessibility of an EPR active triplet state. Cyclic voltammetry shows that introduction of Ph groups renders the complexes easier to reduce. 13C CPMAS NMR analysis provides insights into the cause of the low field shift of the resonances of metal-bonded carbon atoms and provides evidence of the absence of the ß-C-Ti interaction.
ABSTRACT
With the progression in the field of bioinorganic chemistry, the role of transition metal complexes as the most widely used therapeutics is becoming a more and more attractive research area. The complexes of transition metals possess a great variety of attractive pharmacological properties, including anticancer, anti-inflammatory, antioxidant, anti-infective, etc., activities. Transition metal complexes have proven to be potential alternatives to biologically active organic compounds, especially as antitumor agents. The performance of metal coordination compounds in living systems is anticipated to differ generally from the action of non-metal-containing drugs and may offer unique diagnostic and/or therapeutic opportunities. In this review, the rapid development and application of metallocenes and metal complexes of elements from Groups 4 to 7 in cancer diagnostics and therapy have been summarized. Most of the heavy metals discussed in the current review are newly discovered metals. That is why the use of their metal-based compounds has attracted a lot of attention concerning their organometallic and coordination chemistry. All of this imposes more systematic studies on their biological activity, biocompatibility, and toxicity and presupposes further investigations.
Subject(s)
Antineoplastic Agents , Coordination Complexes , Metals, Heavy , Transition Elements , Coordination Complexes/chemistry , Metallocenes , Transition Elements/chemistry , Metals, Heavy/chemistry , Antineoplastic Agents/pharmacology , Antineoplastic Agents/chemistryABSTRACT
Syndiotactic polystyrene (SPS) refers to a type of thermoplastic material with phenyl substituents that are alternately chirally attached on both sides of an aliphatic macromolecular main chain. Owing to its excellent physical and mechanical properties, as well as its chemical stability, high transparency, and electrical insulation characteristics, SPS is used in a wide variety of technical fields. SPS is commonly produced via the stereoselective transition metal-catalyzed coordination polymerization method mediated by stereospecific catalysts, which consists of anionic mono-cyclopentadienyl derivative η5-coordinated single active metal centers (referred to as "mono-Cp'-M"), with active center metals involving Group 4 transition metals (with an emphasis on titanium) and rare-earth (RE) metals of the periodic table. In this context, the use of mono-cyclopentadienyl titanocene (mono-Cp'Ti) catalysts and mono-cyclopentadienyl rare-earth metal (mono-Cp'RE) metallocene catalysts for the syndiospecific polymerization of styrene is discussed. The effects of the mono-cyclopentadienyl ligand structure, cationic active metal types, and cocatalysts on the activity and syndiospecificity of mono-Cp' metallocene catalysts are briefly surveyed.
ABSTRACT
Modern industry of advanced polyolefins extensively uses Group 4 metallocene and post-metallocene catalysts. High-throughput polyolefin technologies demand the use of heterogeneous catalysts with a given particle size and morphology, high thermal stability, and controlled productivity. Conventional Group 4 metal single-site heterogeneous catalysts require the use of high-cost methylalumoxane (MAO) or perfluoroaryl borate activators. However, a number of inorganic phases, containing highly acidic Lewis and Brønsted sites, are able to activate Group 4 metal pre-catalysts using low-cost and affordable alkylaluminums. In the present review, we gathered comprehensive information on MAO- and borate-free activating supports of different types and discussed the surface nature and chemistry of these phases, examples of their use in the polymerization of ethylene and α-olefins, and prospects of the further development for applications in the polyolefin industry.
ABSTRACT
Altering the donor properties of phosphane ligands through substituent variation is an established tool in coordination chemistry and catalysis. This contribution describes the synthesis of two new hybrid donors (L) combining 1,3,5,7-tetramethyl-2,4,6-trioxa-8-phosphaadamantane-8-yl (PCg) and nitrile donor groups at different molecular scaffolds, viz. ferrocene-1,1'-diyl (fc) and 1,2-phenylene. These ligands were used to prepare dimeric Au(I) complexes [Au2 (µ(P,N)-L)2 ][SbF6 ]2 , which were evaluated as silver-free, preformed catalysts in Au-mediated cycloisomerization of (Z)-3-methylpent-2-en-4-yn-1-ol to 2,3-dimethylfuran. The catalyst featuring the ferrocene-based ligand, viz., [Au2 (µ(P,N)-CgPfcCN)2 ][SbF6 ]2 , showed the best catalytic performance at low catalyst loading (0.5 or 0.15â mol.%), which exceeded that of its diphenylphosphanyl analog [Au2 (µ(P,N)-Ph2 PfcCN)2 ][SbF6 ]2 studied earlier and the prototypical Au(I) precatalyst [Au(PPh3 )(MeCN)][SbF6 ].
ABSTRACT
The loading of homogeneous catalysts with support can dramatically improve their performance in olefin polymerization. However, the challenge lies in the development of supported catalysts with well-defined pore structures and good compatibility to achieve high catalytic activity and product performance. Herein, we report the use of an emergent class of porous material-covalent organic framework material (COF) as a carrier to support metallocene catalyst-Cp2 ZrCl2 for ethylene polymerization. The COF-supported catalyst demonstrates a higher catalytic activity of 31.1×106 â g mol-1 h-1 at 140 °C, compared with 11.2×106 â g mol-1 h-1 for the homogenous one. The resulting polyethylene (PE) products possess higher weight-average molecular weight (Mw ) and narrower molecular weight distribution (Ð) after COF supporting, that is, Mw increases from 160 to 308â kDa and Ð drops from 3.3 to 2.2. The melting point (Tm ) is also increased by up to 5.2 °C. Moreover, the PE product possesses a characteristic filamentous microstructure and demonstrates an increased tensile strength from 19.0 to 30.7â MPa and elongation at break from 350 to 1400 % after catalyst loading. We believe that the use of COF carriers will facilitate the future development of supported catalysts for highly efficient olefin polymerization and high-performance polyolefins.
ABSTRACT
Ferrocene-based N-heterocyclic plumbylenes fc[(NSiMe2 R)2 Pb:] (1; fc=1,1'-ferrocenylene) are easily accessible by transamination from [(Me3 Si)2 N]2 Pb and the corresponding 1,1'-diaminoferrocene derivatives fc(NHSiMe2 R)2 . They may form unconventional dimers 2 by a process, which causes the cleavage of a cyclopentadienyl C-H bond and the formation of a Pb-C and an N-H bond. The monomer-dimer equilibrium (2 1â2) has been addressed experimentally and computationally. It critically depends on the steric demand of the N-substituents SiMe2 R, which has been varied systematically by using homologues with aliphatic (R=methyl, ethyl, isopropyl, tert-butyl) and aromatic units (R=phenyl, mesityl, ferrocenyl). Even in the sterically least congested case (R=methyl), dimerization is only slightly exergonic. It eventually becomes prohibitively endergonic with increasingly larger substituents and is thus not observed for R=tert-butyl, mesityl, and ferrocenyl. R=phenyl represents a borderline case, where the dimer is still detectable in the equilibrium mixture, albeit as a very minor component, in accord with the slightly endergonic Gibbs free energy change calculated for its formation. Addition of 4-dimethylaminopyridine (DMAP) to the monomer-dimer equilibrium mixtures cleanly affords the corresponding adducts [1(DMAP)], irrespective of the equilibrium composition.
ABSTRACT
Benzene-1,2,4,5-tetrathiolate (btt) has been used as a bridging ligand to prepare a redox active (molybdenocene dithiolene)-based bimetallic complex Cp2 Mo(btt)MoCp2 , which exhibits four successive electron transfers up to the tetracation. Spectro-electrochemical investigations together with DFT and TD-DFT calculations evidence that the two electroactive MoS2 C2 metallacycles are electronically coupled in the monocationic as in the dicationic state. Two salts of the dication [Cp2 Mo(btt)MoCp2 ]2+ have been structurally characterized with PF6 - and HSO4 - counterions, showing different chair or boat conformations associated with variable folding angles of the two MoS2 C2 metallacycles along the S-S hinge. The bis-oxidized dicationic complex exhibits a diradical character, with both radicals essentially localized on the metallacycles and with antiferromagnetic coupling evidenced from magnetic susceptibility measurements.
ABSTRACT
Ionic liquids (ILs) are salts with low melting points and are useful as electrolytes and solvents. We have developed ILs containing cationic metal complexes, which form a family of functional liquids that exhibit unique physical properties and chemical reactivities originating from metal complexes. Our study explores the liquid chemistry in the field of coordination chemistry, where solid-state chemistry is currently the main focus. This review describes the molecular design, physical properties, and reactivities of organometallic ILs containing sandwich or half-sandwich complexes. This paper mainly covers stimuli-responsive ILs, whose magnetic properties, solvent polarities, colors, or structures change by the application of external fields, such as light, heat, and magnetic fields, or by reaction with coordinating molecules.
ABSTRACT
The benzene ligand at CpV(η6 -C6 H6 ) (1) is exchanged for pentafulvenes. Using sterically demanding pentafulvenes gives a clean exchange reaction, yielding vanadium pentafulvene (2 a and 2 b) and benzofulvene complexes (3 a and 3 b). The molecular structures of the target compounds suggest a π-η5 :σ-η1 coordination mode with a vanadiumIII center. With the sterically low demanding 6,6-dimethylpentafulvene, a C-H activation at the leaving ligand is observed, yielding the ring-substituted vanadoceneII 4. The reactivity of the pentafulvene complexes was investigated. A series of unprecedented vanadoceneIII compounds were synthesized: Under mild conditions, E-H splitting of 4-tert-butylphenol, diphenylamine, and 2,6-diisopropylaniline yield well characterized examples of rare vanadoceneIII phenolate and amide complexes. Insertion reactions into the V-Cexo bond of the pentafulvene complexes by multiple bond containing substrates were found for acetone, 4-chlorobenzonitril and N,N'-dicyclohexylcarbodiimide.
ABSTRACT
The potential application of η6 -metalated aryl iodides as organocatalyst has been explored by means of computational methods. It is found that the enhanced halogen bonding donor ability of these species, in comparison with their demetalated counterparts, translates into a significant acceleration of the Diels-Alder cycloaddition reaction involving cyclohexadiene and methyl vinyl ketone. The factors behind this acceleration, the endo-exo selectivity of the process and the influence of the nature of the transition metal fragment in the activity of these species are quantitatively explored in detail by means of the combination of the Activation Strain Model of reaction and the Energy Decomposition Analysis methods.
ABSTRACT
In the last decade, planar chiral ferrocenes have attracted a growing interest in several fields, particularly in asymmetric catalysis, medicinal chemistry, chiroptical spectroscopy and electrochemistry. In this frame, the access to pure or enriched enantiomers of planar chiral ferrocenes has become essential, relying on the availability of efficient asymmetric synthesis procedures and enantioseparation methods. Despite this, in enantioseparation science, these metallocenes were not comprehensively explored, and very few systematic analytical studies were reported in this field so far. On the other hand, enantioselective high-performance liquid chromatography has been frequently used by organic and organometallic chemists in order to measure the enantiomeric purity of planar chiral ferrocenes prepared by asymmetric synthesis. On these bases, this review aims to provide the reader with a comprehensive overview on the enantioseparation of planar chiral ferrocenes by discussing liquid-phase enantioseparation methods developed over time, integrating this main topic with the most relevant aspects of ferrocene chemistry. Thus, the main structural features of ferrocenes and the methods to model this class of metallocenes will be briefly summarized. In addition, planar chiral ferrocenes of applicative interest as well as the limits of asymmetric synthesis for the preparation of some classes of planar chiral ferrocenes will also be discussed with the aim to orient analytical scientists towards 'hot topics' and issues which are still open for accessing enantiomers of ferrocenes featured by planar chirality.
Subject(s)
Ferrous Compounds , Metallocenes , Ferrous Compounds/chemistry , Stereoisomerism , Chromatography, High Pressure Liquid/methodsABSTRACT
Olefin and diene transformations, catalyzed by organoaluminum-activated metal complexes, are widely used in synthetic organic chemistry and form the basis of major petrochemical processes. However, the role of M−(µ-Cl)−Al bonding, being proven for certain >C=C< functionalization reactions, remains unclear and debated for essentially more important industrial processes such as oligomerization and polymerization of α-olefins and conjugated dienes. Numerous publications indirectly point at the significance of M−(µ-Cl)−Al bonding in Ziegler−Natta and related transformations, but only a few studies contain experimental or at least theoretical evidence of the involvement of M−(µ-Cl)−Al species into catalytic cycles. In the present review, we have compiled data on the formation of M−(µ-Cl)−Al complexes (M = Ti, Zr, V, Cr, Ni), their molecular structure, and reactivity towards olefins and dienes. The possible role of similar complexes in the functionalization, oligomerization and polymerization of α-olefins and dienes is discussed in the present review through the prism of the further development of Ziegler−Natta processes and beyond.
ABSTRACT
Metallocenes represent one of the most important classes of organometallics with wide prospects for practical use in various fields of chemistry, materials science, molecular electronics, and biomedicine. Many applications of these metal complexes are based on their ability to form molecular ions. We report the first results concerning the changes in the molecular and electronic structure of decamethylmanganocene, Cp*2Mn, upon ionization provided by the high-resolution mass-analyzed threshold ionization (MATI) spectroscopy supported by DFT calculations. The precise ionization energy of Cp*2Mn is determined as 5.349 ± 0.001 eV. The DFT modeling of the MATI spectrum shows that the main structural deformations accompanying the detachment of an electron consist in the elongation of the Mn-C bonds and a change in the Me out-of-plane bending angles. Surprisingly, the DFT calculations predict that most of the reduction in electron density (ED) upon ionization is associated with the hydrogen atoms of the substituents, despite the metal character of the ionized orbital. However, the ED difference isosurfaces reveal a complex mechanism of the charge redistribution involving also the carbon atoms of the molecule.
Subject(s)
Coordination Complexes , Carbon , Hydrogen , Lasers , Metallocenes , Spectrum AnalysisABSTRACT
For more than 40â years, the synthesis of C2 -symmetric indenyl-based racemic metallocenes for the isoselective polymerization of propylene relied on a tedious separation of the produced rac and meso isomers. Status quo, latter are considered wasteful as they produce atactic polypropylene (aPP) rather than isotactic polypropylene (iPP) if activated with methylaluminoxane (MAO). Unexpectedly, the in situ activation of meso hafnocene I yielded perfectly isotactic polypropylene. We verified an isomerization of the meso compound to the corresponding racemic one upon triisobutylaluminum (TIBA) addition via nuclear magnetic resonance (NMR) spectroscopy and established an easy and convenient polymerization protocol, enabling productivities comparable to pure rac-I if applied to pure meso-I or a mixture of both isomers. With this established isomerization protocol, the potential yield of iPP was enhanced by more than 400 %. This protocol was also shown to be applicable to other meso hafnocenes and some initial mechanistic insights were received.
ABSTRACT
Eight push-pull systems involving containing four transition metals (iron, ruthenium, cobalt, and nickel), metallocenes as donor groups, cyanoacrylate as electron attractor group, and thiophene-N = N- pyrimidine derivatives as π-conjugated bridges were designed and studied using DFT and TD-DFT methods involving B3LYP and CAM-B3LYP functionals combined with the cc-pVDZ/LANL2DZ basis sets. The main purpose of this work is to determine the effect of metallocene in improving the photosensitization property of such chromophores. This was done by calculating their light-harvesting efficiency LHE as well as other properties employed for DSSC application. The considered dyes were first studied in the gas phase, then in the presence of TiO2 nanoparticles representing the semi-conductor, and finally in the presence of a specific implicit solvent. The presence of iron as metal involved in the metallocene group supplemented by extending the π-conjugated bridge by a cyanovinyl spacer was demonstrated so as to give the most optimal response taking into account the lower cost and toxicity as well as the friendliness to the environment of iron as metal.