Development of a High-Sensitivity Millimeter-Wave Radar Imaging System for Non-Destructive Testing.

There is an urgent need to develop non-destructive testing (NDT) methods for infrastructure facilities and residences, etc., where human lives are at stake, to prevent collapse due to aging or natural disasters such as earthquakes before they occur. In such inspections, it is desirable to develop a remote, non-contact, non-destructive inspection method that can inspect cracks as small as 0.1 mm on the surface of a structure and damage inside and on the surface of the structure that cannot be seen by the human eye with high sensitivity, while ensuring the safety of the engineers inspecting the structure. Based on this perspective, we developed a radar module (absolute gain of the transmitting antenna: 13.5 dB; absolute gain of the receiving antenna: 14.5 dB) with very high directivity and minimal loss in the signal transmission path between the radar chip and the array antenna, using our previously developed technology. A single-input, multiple-output (SIMO) synthetic aperture radar (SAR) imaging system was developed using this module. As a result of various performance evaluations using this system, we were able to demonstrate that this system has a performance that fully satisfies the abovementioned indices. First, the SNR in millimeter-wave (MM-wave) imaging was improved by 5.4 dB compared to the previously constructed imaging system using the IWR1443BOOST EVM, even though the measured distance was 2.66 times longer. As a specific example of the results of measurements on infrastructure facilities, the system successfully observed cracks as small as 0.1 mm in concrete materials hidden under glass fiber-reinforced tape and black acrylic paint. In this case, measurements were also made from a distance of about 3 m to meet the remote observation requirements, but the radar module with its high-directivity and high-gain antenna proved to be more sensitive in detecting crack structures than measurements made from a distance of 780 mm. In order to estimate the penetration length of MM waves into concrete, an experiment was conducted to measure the penetration of MM waves through a thin concrete slab with a thickness of 3.7 mm. As a result, Λexp = 6.0 mm was obtained as the attenuation distance of MM waves in the concrete slab used. In addition, transmission measurement experiments using a composite material consisting of ceramic tiles and fireproof board, which is a component of a house, and experiments using composite plywood, which is used as a general housing construction material in Japan, succeeded in making perspective observations of defects in the internal structure, etc., which are invisible to the human eye.

Antenna Integration for Millimeter-Wave RF Sensing and Millimeter-Wave Communication Mountable on a Platform.

An array antenna for millimeter-wave communication and an array antenna for millimeter-wave sensing are designed and put together into one structure. Because millimeter-wave signals become weaker fast with the increasing distance and any kind of error in the required functions of the antenna has to be minimized, pointing error from the target direction should be prevented. The device is a millimeter-wave sensing antenna with high directivity to check the straight link between the TX and RX sides of wireless communication. A 24 GHz 8-by-16 array antenna which generates stronger signals for sensing resolves the drawback of a 28 GHz 1-by-4 array antenna that is commonly seen in 5G wireless terminals. The sensing and communication antennas are integrated as a planar structure mountable on platforms, which is investigated with regard to forming wireless links over a distance of several meters with an input power of less than 0 dBm. Additionally, in the event of a reflecting surface disturbing the straight path and worsening the pointing error in RF signal transfer, the dual-capability of the combination is presented on the basis of intuitive electromagnetic experiments.

A New Method for Detecting Dehydration of the Human Body Using Non-Contact Millimeter Wave Radiometry.

Dehydration is a common problem in the aging population. Medical professionals can detect dehydration using either blood or urine tests. This requires experimental tests in the lab as well as urine and blood samples to be obtained from the patients. This paper proposed 100 GHz millimeter wave radiometry for early detection of dehydration. Reflectance measurements were performed on healthy and dehydrated patients of both genders (120 males and 80 females) in the aging population. Based on the cause of dehydration, the patient groups were divided into three categories: (1) patients dehydrated due to less thirst sensation, (2) patients dehydrated due to illnesses (vomiting and diarrhea), and (3) patients dehydrated due to diabetes. Reflectance measurements were performed on eight locations: (1) the palm, (2) the back of the hand, (3) the fingers, (4) the inner wrist, (5) the outer wrist, (6) the volar side of the arm, (7) the dorsal surface of the arm, and (8) the elbow. Skin dehydrated due to vomiting and diarrhea was found to have lower reflectance at all the measurement locations compared with healthy and other types of dehydrated skin. The elbow region showed the highest difference in reflectance between healthy and dehydrated skin. This indicates that radiometric sensitivity is sufficient to detect dehydration in a few seconds. This will reduce the patient's waiting time and the healthcare professional's intervention time as well as allow early treatment of dehydration, thus avoiding admission to hospitals.

A novel frequency 32-tupling ROF system without bit walk-off effect based on MZM with inserting pilot.

A novel scheme for a frequency 32-tupling millimeter wave (MMW) radio over fiber(ROF) system without the bit walk-off effect is proposed. The operation principle and feasibility of our proposed scheme are theoretically analyzed and verified with simulation experiments. The main part of our scheme is a ±16th order sidebands generator (SG) which is constructed by eight Mach-Zehnder modulators (MZM) connected in parallel. In the back-to-back(BTB) transmission case, by properly adjusting the voltage and initial phase of the radio frequency (RF) drive signals of the MZMs, ±16th order sidebands are generated by the SG. In the data transmission case, the data signal is split into two beams first, one of which modulates the RF drive signal with an electrical phase modulator (PM), and the other is amplified by an electrical gainer (EG), and then the two beams are combined into one and used as the RF drive signal of the MZMs. By adjusting the modulation index of the PM and the gain of the EG, the data signal can be modulated only to the +16th order sideband of the output of the SG. The optical carrier from the CW laser is split into two paths, one is sent into the SG, and the other is used as a pilot. The output signal of SG is combined with the pilot signal and is transmitted to the base station(BS) via optical fiber. In BS, the pilot signal is filtered out by an FBG and used as the carrier for uplink for carrier reuse. After filtering out the pilot, the signal from the FBG which is ±16th order sidebands is injected into the photodetector, and a frequency 32-tupling MMW with downlink data is generated. The influence on the bit error rate (BER) and Q factor by the key parameters in the system is also analyzed. Our scheme can not only effectively overcome the bit walk-off effect caused by optical fiber chromatic dispersion, greatly increase the fiber transmission distance, but also effectively improve the performance of the downlink, it has important application prospects in ROF systems.

Design and implementation of multi-band reflectarray metasurface for 5G millimeter wave coverage enhancement.

A compact low-profile multi-band millimeter-wave (mm-wave) reflectarray metasurface design is presented for coverage enhancement in 5G and beyond cellular communication. The proposed single-layer metasurface exhibits a stable reflection response under oblique incidence angles of up to 60 ∘ at 24 and 38 GHz, and transmission response at 30 GHz, effectively covering the desired 5G mm-wave frequency bands. The proposed reflectarray metasurface is polarization insensitive and performs equally well under TE and TM polarized incident waves due to the symmetric pattern. In addition, the low profile of the proposed metasurface makes it appropriate for conformal applications. In comparison to the state-of-the-art, the proposed reflectarray metasurface unit cell design is not only compact (3.3  ×  3.3 mm 2 ) but also offers two reflections and one transmission band based on a single-layer structure. It is easy to reconfigure the proposed metasurface unit cell for any other frequency band by adjusting a few design parameters. To validate the concept of coverage enhancement, a 32  ×  x32 unit-cell prototype of the proposed reflectarray metasurface is fabricated and measured under different scenarios. The experimental results demonstrate that a promising signal enhancement of 20-25 dB is obtained over the entire 5G mm-wave n258, n259, and n260 frequency bands. The proposed reflectarray metasurface has a high potential for application in mm-wave 5G networks to improve coverage in dead zones or to overcome obstacles that prevent direct communication linkages.

Millimeter-Wave Band Electro-Optical Imaging System Using Polarization CMOS Image Sensor and Amplified Optical Local Oscillator Source.

In this study, we developed and demonstrated a millimeter-wave electric field imaging system using an electro-optic crystal and a highly sensitive polarization measurement technique using a polarization image sensor, which was fabricated using a 0.35-µm standard CMOS process. The polarization image sensor was equipped with differential amplifiers that amplified the difference between the 0° and 90° pixels. With the amplifier, the signal-to-noise ratio at low incident light levels was improved. Also, an optical modulator and a semiconductor optical amplifier were used to generate an optical local oscillator (LO) signal with a high modulation accuracy and sufficient optical intensity. By combining the amplified LO signal and a highly sensitive polarization imaging system, we successfully performed millimeter-wave electric field imaging with a spatial resolution of 30×60 µm at a rate of 1 FPS, corresponding to 2400 pixels/s.

Emerging non-invasive microwave and millimeter-wave imaging technologies for food inspection.

The microwave and millimeter-wave (MMW) imaging technology is gaining increasing interest for food inspection. It allows for noninvasive, contactless, and fast scanning capabilities, while being cost-efficient and safe to human. This review paper introduces the fundamentals in the interaction of electromagnetic wave with food materials and the current MMW sensing and imaging systems used for foods. Then we present emerging technologies in MMW imaging for inspecting food quality and safety, aiming to meet the modern food industry's demand. According to the most recent technological advancements, it is expected that high-performance antenna, ultrawide bandwidth signal generation, nano-scale semiconductor technologies, radio frequency identification with inductance-capacitance resonator, and machine learning could significantly enhance the capabilities of MMW imaging systems for food inspection.

An Overview of Millimeter-Wave Radar Modeling Methods for Autonomous Driving Simulation Applications.

Autonomous driving technology is considered the trend of future transportation. Millimeter-wave radar, with its ability for long-distance detection and all-weather operation, is a key sensor for autonomous driving. The development of various technologies in autonomous driving relies on extensive simulation testing, wherein simulating the output of real radar through radar models plays a crucial role. Currently, there are numerous distinctive radar modeling methods. To facilitate the better application and development of radar modeling methods, this study first analyzes the mechanism of radar detection and the interference factors it faces, to clarify the content of modeling and the key factors influencing modeling quality. Then, based on the actual application requirements, key indicators for measuring radar model performance are proposed. Furthermore, a comprehensive introduction is provided to various radar modeling techniques, along with the principles and relevant research progress. The advantages and disadvantages of these modeling methods are evaluated to determine their characteristics. Lastly, considering the development trends of autonomous driving technology, the future direction of radar modeling techniques is analyzed. Through the above content, this paper provides useful references and assistance for the development and application of radar modeling methods.

Vehicle Occupant Detection Based on MM-Wave Radar.

With the continuous development of automotive intelligence, vehicle occupant detection technology has received increasing attention. Despite various types of research in this field, a simple, reliable, and highly private detection method is lacking. This paper proposes a method for vehicle occupant detection using millimeter-wave radar. Specifically, the paper outlines the system design for vehicle occupant detection using millimeter-wave radar. By collecting the raw signals of FMCW radar and applying Range-FFT and DoA estimation algorithms, a range-azimuth heatmap was generated, visually depicting the current status of people inside the vehicle. Furthermore, utilizing the collected range-azimuth heatmap of passengers, this paper integrates the Faster R-CNN deep learning networks with radar signal processing to identify passenger information. Finally, to test the performance of the detection method proposed in this article, an experimental verification was conducted in a car and the results were compared with those of traditional machine learning algorithms. The findings indicated that the method employed in this experiment achieves higher accuracy, reaching approximately 99%.

Advanced Millimeter-Wave Radar System for Real-Time Multiple-Human Tracking and Fall Detection.

This study explored an indoor system for tracking multiple humans and detecting falls, employing three Millimeter-Wave radars from Texas Instruments. Compared to wearables and camera methods, Millimeter-Wave radar is not plagued by mobility inconveniences, lighting conditions, or privacy issues. We conducted an initial evaluation of radar characteristics, covering aspects such as interference between radars and coverage area. Then, we established a real-time framework to integrate signals received from these radars, allowing us to track the position and body status of human targets non-intrusively. Additionally, we introduced innovative strategies, including dynamic Density-Based Spatial Clustering of Applications with Noise (DBSCAN) clustering based on signal SNR levels, a probability matrix for enhanced target tracking, target status prediction for fall detection, and a feedback loop for noise reduction. We conducted an extensive evaluation using over 300 min of data, which equated to approximately 360,000 frames. Our prototype system exhibited a remarkable performance, achieving a precision of 98.9% for tracking a single target and 96.5% and 94.0% for tracking two and three targets in human-tracking scenarios, respectively. Moreover, in the field of human fall detection, the system demonstrates a high accuracy rate of 96.3%, underscoring its effectiveness in distinguishing falls from other statuses.

Localization Performance Analysis and Algorithm Design of Reconfigurable Intelligent Surface-Assisted D2D Systems.

The research on high-precision and all-scenario localization using the millimeter-wave (mmWave) band is of great urgency. Due to the characteristics of mmWave, blockages make the localization task more complex. This paper proposes a cooperative localization system among user equipment (UEs) assisted by reconfigurable intelligent surfaces (RISs), which considers device-to-device (D2D) communication. RISs are used as anchor points, and position estimation is achieved through signal exchanges between UEs. Firstly, we establish a localization model based on this system and derive the UEs' positioning error bound (PEB) as a performance metric. Then, a UE-RIS joint beamforming design is proposed to optimize channel state information (CSI) with the objective of achieving the minimum PEB. Finally, simulation analysis demonstrates the advantages of the proposed scheme over RIS-assisted base station positioning, achieving centimeter-level accuracy with a 10 dBm lower transmission power.

Antenna Array Design Based on Low-Temperature Co-Fired Ceramics.

With the continuous development of wireless communication technology, the frequency band of 6G communication systems is moving towards higher frequencies such as millimeter waves and terahertz. In such high-frequency situations, wireless transmission requires antenna modules to be provided with characteristics of miniaturization, high integration, and high gain, which presents new challenges to the development of antenna technology. In this article, a 4 × 4 antenna array using multilayered low-temperature co-fired ceramic is proposed, operating in W-band, with a feeding network based on substrate-integrated waveguide, and an antenna element formed through the combination of a substrate-integrated cavity and surface parasitic patches, which guaranteed the array to possess the advantages of high integration and high gain. Combined with the substrate-integrated waveguide to a rectangular waveguide transition structure designed in the early stage, a physical array with a standard metal rectangular waveguide interface was fabricated and tested. The test results show that the gain of the antenna array is higher than 18 dBi from 88 to 98 GHz, with a maximum of 20.4 dBi.

A 60 GHz Slotted Array Horn Antenna for Radar Sensing Applications in Future Global Industrial Scenarios.

This paper presents the design of a 60 GHz millimeter-wave (MMW) slot array horn antenna based on the substrate-integrated waveguide (SIW) structure. The novelty of this device resides in the achievement of a broad impedance bandwidth and high gain performance by meticulously engineering the radiation band structure and slot array. The antenna demonstrates an impressive impedance bandwidth of 14.96 GHz (24.93%), accompanied by a remarkable maximum reflection coefficient of -39.47 dB. Furthermore, the antenna boasts a gain of 10.01 dBi, showcasing its outstanding performance as a high-frequency antenna with a wide bandwidth and high gain. To validate its capabilities, we fabricated and experimentally characterized a prototype of the antenna using a probe test structure. The measurement results closely align with the simulation results, affirming the suitability of the designed antenna for radar sensing applications in future global industrial scenarios.

A Compact MIMO Antenna Based on Modal Analysis for 5G Wireless Applications.

This article presents a planar, non-angular, series-fed, dual-element dipole array MIMO antenna operating at 28 GHz with the metasurface-based isolation improvement technique. The initial design is a single-element antenna with a dual dipole array which is series-fed. These dipole elements are non-uniform in shape and distance. This dipole antenna results in end-fire radiation. The dipole antenna excites the J1 mode for its operation. Further, with the view to improve channel capacity, the dipole array expands the antenna to a three-element MIMO antenna. In the MIMO antenna structure, the sum of the J1, J2, and J3 modes is excited, causing resonance at 28 GHz. This article also proposes a metasurface structure with wide stopband characteristics at 28 GHz for isolation improvement. The metasurface is composed of rectangle-shaped structures. The defected ground and metasurface structure combination suppresses the surface wave coupling among the MIMO elements. The proposed antenna results in a bandwidth ranging from 26.7 to 29.6 GHz with isolation improvement greater than 21 dB and a gain of 6.3 dBi. The antenna is validated with the diversity parameters of envelope correlation coefficient, diversity gain, and channel capacity loss.

Spectral Efficiency Maximization for Mixed-Structure Cognitive Radio Hybrid Wideband Millimeter-Wave Transceivers in Relay-Assisted Multi-User Multiple-Input Multiple-Output Systems.

This paper proposes a cognitive radio network (CRN)-based hybrid wideband precoding for maximizing spectral efficiency in millimeter-wave relay-assisted multi-user (MU) multiple-input multiple-output (MIMO) systems. The underlying problem is NP-hard and non-convex due to the joint optimization of hybrid processing components and the constant amplitude constraint imposed by the analog beamformer in the radio frequency (RF) domain. Furthermore, the analog beamforming solution common to all sub-carriers adds another layer of design complexity. Two hybrid beamforming architectures, i.e., mixed and fully connected ones, are taken into account to tackle this problem, considering the decode-and-forward (DF) relay node. To reduce the complexity of the original optimization problem, an attempt is made to decompose it into sub-problems. Leveraging this, each sub-problem is addressed by following a decoupled design methodology. The phase-only beamforming solution is derived to maximize the sum of spectral efficiency, while digital baseband processing components are designed to keep interference within a predefined limit. Computer simulations are conducted by changing system parameters under different accuracy levels of channel-state information (CSI), and the obtained results demonstrate the effectiveness of the proposed technique. Additionally, the mixed structure shows better energy efficiency performance compared to its counterparts and outperforms benchmarks.

Identification of Respiratory Pauses during Swallowing by Unconstrained Measuring Using Millimeter Wave Radar.

Breathing temporarily pauses during swallowing, and the occurrence of inspiration before and after these pauses may increase the likelihood of aspiration, a serious health problem in older adults. Therefore, the automatic detection of these pauses without constraints is important. We propose methods for measuring respiratory movements during swallowing using millimeter wave radar to detect these pauses. The experiment involved 20 healthy adult participants. The results showed a correlation of 0.71 with the measurement data obtained from a band-type sensor used as a reference, demonstrating the potential to measure chest movements associated with respiration using a non-contact method. Additionally, temporary respiratory pauses caused by swallowing were confirmed by the measured data. Furthermore, using machine learning, the presence of respiring alone was detected with an accuracy of 88.5%, which is higher than that reported in previous studies. Respiring and temporary respiratory pauses caused by swallowing were also detected, with a macro-averaged F1 score of 66.4%. Although there is room for improvement in temporary pause detection, this study demonstrates the potential for measuring respiratory movements during swallowing using millimeter wave radar and a machine learning method.

Real-Time Synthetic Aperture Radar Imaging with Random Sampling Employing Scattered Power Mapping.

A novel image-reconstruction method is proposed for the processing of data acquired at random spatial positions. The images are reconstructed and updated in real time concurrently with the measurements to produce an evolving image, the quality of which is continuously improving and converging as the number of data points increases with the stream of additional measurements. It is shown that the images converge to those obtained with data acquired on a uniformly sampled surface, where the sampling density satisfies the Nyquist limit. The image reconstruction employs a new formulation of the method of scattered power mapping (SPM), which first maps the data into a three-dimensional (3D) preliminary image of the target on a uniform spatial grid, followed by fast Fourier space image deconvolution that provides the high-quality 3D image.

Frequency-Reconfigurable Millimeter-Wave Rectangular Dielectric Resonator Antenna.

This paper introduces an innovative and cost-effective approach for developing a millimeter-wave (mmWave) frequency-reconfigurable dielectric resonator antenna (DRA), which has not been reported before. The antenna integrates two rectangular DRA elements, where each DRA is centrally fed via a slot. A strategically positioned PIN diode is employed to exert control over performance by modulating the ON-OFF states of the diode, thereby simplifying the design process and reducing losses. In the OFF state, the first DRA, RDRA-I, exclusively supports the TE311 resonance mode at 24.3 GHz, offering a 2.66% impedance bandwidth and achieving a maximum broadside gain of 9.2 dBi. Conversely, in the ON state, RDRA-I and RDRA-II concurrently operate in the TE513 resonance mode at 29.3 GHz, providing a 2.7% impedance bandwidth and yielding a high gain of up to 11.8 dBi. Experimental results substantiate that the proposed antenna presents an attractive solution for applications necessitating frequency-reconfigurable and high-performance mmWave antennas in 5G and Beyond 5G (B5G) communication systems.

First noncontact millimeter-wave radar measurement of heart rate in great apes: Validation in chimpanzees (Pan troglodytes).

Heart rate is a crucial vital sign and a valuable indicator for assessing the physical and psychological condition of a target animal. Heart rate contributes to (1) fundamental information for cognitive research, (2) an indicator of psychological and physical stress, and (3) improving the animal welfare of captive animals, especially in nonhuman primate studies. Heart rate has been measured using a contact-type device; however, the device burdens the target animals and that there are risks associated with anesthesia during installation. This study explores the application of heartbeat measurement techniques using millimeter-wave radar, primarily developed for humans, as a remote and noninvasive method for measuring the heart rate of nonhuman primates. Through a measurement test conducted on two chimpanzees, we observed a remarkable correspondence between the peak frequency spectrum of heart rate estimated using millimeter-wave radar and the mean value obtained from electrocardiograph data, thereby validating the accuracy of the method. To the best of our knowledge, this is the first demonstration of the precise measurement of great apes' heart rate using millimeter-wave radar technology. Compared to heart rate measurement using video analysis, the method using millimeter-wave radar has the advantage that it is less susceptible to weather and lighting conditions and that measurement techniques for multiple individuals have been developed for human subjects, while its disadvantage is that validation of measurement from long distances has not been completed. Another disadvantage common to both methods is that measurement becomes difficult when the movement of the target individual is large. The possibility of noncontact measurement of heart rate in wild and captive primates will undoubtedly open up a new research area while taking animal welfare into consideration.

Electromagnetic field exposure monitoring of commercial 28-GHz band 5G base stations in Tokyo, Japan.

Fifth generation (5G) wireless communication is being rolled out around the world. In this work, the latest radio frequency electromagnetic field (EMF) exposure measurement results on commercial 28-GHz band 5G base stations (BSs) deployed in the urban area of Tokyo, Japan, are presented. The measurements were conducted under realistic traffic conditions with a 5G smartphone and using both omnidirectional and horn antennas. First and foremost, in all cases, the electric-field (E-field) intensity is much lower (<-38 dB) than the exposure limits. The E-field intensities for traffic-off cases do not show any significant difference between the two antennas with the maximum being 3.6 dB. For traffic-on cases, the omnidirectional antenna can undesirably capture the radio wave from the smartphone in some cases, resulting in a 7-13 dB higher E-field intensity than that using the horn antenna. We also present comparative results between 4G long term evolution BSs and sub-6-GHz band and 28-GHz band 5G BSs and provide recommendations on acquiring meaningful EMF exposure data. This work is a further step toward the standardization of the measurement method regarding quasi-millimeter/millimeter wave 5G BSs.