ABSTRACT
In order to selectively oxidize benzyl alcohol, a novel noble metal catalyst based on polymer ionic liquids with a core-shell structure was created. First, polymer ionic liquid microspheres (PILMs) were prepared by free radical polymerization. Second, the in situ adsorption of Au nanoparticles on the surface of PILMs was accomplished, thanks to the strong electrostatic interaction between N atoms and metal ions on the diazole ring of PILMs. Additionally, the introduction of Al(OH)3 prevented the aggregation of Au nanoparticles and promoted the catalytic reaction. Finally, the PILM/Au/Al(OH)3 catalyst with a core-shell structure was formed. The effectiveness of the PILM/Au/Al(OH)3 catalyst was assessed by varying the catalyst's type, quantity, amount of Au, amount of H2O2, temperature, and reaction time. After five cycles of experiments, the catalyst was effective and reusable. In addition, the potential catalytic mechanism of the catalyst in the oxidation of benzyl alcohol was proposed.
ABSTRACT
In this study, antibacterial polymer blends based on Polyvinyl Chloride (PVC) and Polystyrene-Ethylene-Butylene-Styrene (SEBS), loaded with the ionic liquid (IL) 1-hexadecyl-3-methyl imidazolium 1,3-dimethyl 5-sulfoisophthalate (HdmimDMSIP) at three different concentrations (1%, 5%, and 10%), were produced. The IL/blends were characterized by their thermo-mechanical properties, surface morphology, and wettability. IL release from the blends was also evaluated. The agar diffusion method was used to test the antibacterial activity of the blends against Staphylococcus epidermidis and Escherichia coli. Results from thermal analyses showed compatibility between the IL and the PVC matrix, while phase separation in the SEBS/IL blends was observed. These results were confirmed using PY-GC MS data. SEM analyses highlighted abundant IL deposition on PVC blend film surfaces containing the IL at 5-10% concentrations, whereas the SEBS blend film surfaces showed irregular structures similar to islands of different sizes. Data on water contact angle proved that the loading of the IL into both polymer matrices induced higher wettability of the blends' surfaces, mostly in the SEBS films. The mechanical analyses evidenced a lowering of Young's Modulus, Tensile Stress, and Strain at Break in the SEBS blends, according to IL concentration. The PVC/IL blends showed a similar trend, but with an increase in the Strain at Break as IL concentration in the blends increased. Both PVC/IL and SEBS/IL blends displayed the best performance against Staphylococcus epidermidis, being active at low concentration (1%), whereas the antimicrobial activity against Escherichia coli was lower than that of S. epidermidis. Release data highlighted an IL dose-dependent release. These results are promising for a versatile use of these antimicrobial polymers in a variety of fields.
ABSTRACT
Platinum and palladium are the first choice electrocatalysts to drive the hydrogen evolution reaction. In this report, surface modification was introduced as a potential approach to generate hybrid electrocatalyst. The immobilized polymer brush, poly(1-allyl-3-methylimidazolium) (PAMI), was used as a nanostructured template for guiding the electrochemical deposition of metallic nanoparticles (Pd, Pt). The intrinsic properties of the polymer brush in term of nanostructured architecture and the anions mobility within the polymer was exploited to generate a hybrid electrocatalyst. The latter was generated using two different approaches including the direct electrochemical deposition of Pd or Pt metal and the indirect approach through the anion exchange reaction followed by the electrochemical deposition under self-electrolytic conditions. The hybrid structure based on the polymer/metallic NP exhibits an enhancement of the catalytic performance toward hydrogen evolution reaction with a low Tafel slope and overpotential. Interestingly, the indirect approach leads to decrease the metal loading by two orders of magnitude, when compared to those generated in the absence of the polymeric layer, while retaining the electrocatalytic performance.
ABSTRACT
An anomalous plasticizing effect was observed in polymer/ionic liquid (IL) solutions by applying broad range of rheological techniques. Poly(ethylene oxide)(PEO)/IL solutions exhibit stronger dynamic temperature dependence than pure PEO, which is in conflict with the knowledge that lower-Tg solvent increases the fractional free volume. For poly(methy methacrylate)(PMMA)/IL solutions, the subtle anomaly was detected from the fact that the effective glass transition temperature Tg,eff of PMMA in IL is higher than the prediction of the self-concentration model, while in conventional polymer solutions, Tg,eff follows the original Fox equation. Observations in both solutions reveal retarded segmental dynamics, consistent with a recent simulation result (Macromolecules, 2018, 51, 5336) that polymer chains wrap the IL cations by hydrogen bonding interactions and the segmental unwrapping delays their relaxation. Start-up shear and nonlinear stress relaxation tests of polymer/IL solutions follow a universal nonlinear rheological behavior as polymer melts and solutions, indicating that the segment-cation interaction is not strong enough to influence the nonlinear chain orientation and stretch. The present work may arouse the further theoretical, experimental, and simulation interests in interpreting the effect of complex polymer-IL interaction on the dynamics of polymer/IL solutions.
ABSTRACT
A photopolymerization method is used to prepare a mixture of polymer ionic liquid (PIL) and ionic liquid (IL). This mixture is used as a solid-state electrolyte in carbon nanoparticle (CNP)-based symmetric supercapacitors. The solid electrolyte is a binary mixture of a PIL and its corresponding IL. The PIL matrix is a cross-linked polyelectrolyte with an imidazole salt cation coupled with two anions of Br- in PIL-M-(Br) and TFSI- in PIL-M-(TFSI), respectively. The corresponding ionic liquids have imidazolium salt cation coupled with two anions of Br- and TFSI-, respectively. This study investigates the electrochemical characteristics of PILs and their corresponding IL mixtures used as a solid electrolyte in supercapacitors. Results show that a specific capacitance, maximum power density and energy density of 87 and 58 F·g-¹, 40 and 48 kW·kg-¹, and 107 and 59.9 Wh·kg-¹ were achieved in supercapacitors based on (PIL-M-(Br)) and (PIL-M-(TFSI)) solid electrolytes, respectively.