Cost-effectiveness of restorative treatments for permanent molars with severe molar incisor hypomineralization: perspectives for the Brazilian public health system.

OBJECTIVES: To undertake a cost-effectiveness analysis of restorative treatments for a first permanent molar with severe molar incisor hypomineralization from the perspective of the Brazilian public system. MATERIALS AND METHODS: Two models were constructed: a one-year decision tree and a ten-year Markov model, each based on a hypothetical cohort of one thousand individuals through Monte Carlo simulation. Eight restorative strategies were evaluated: high viscosity glass ionomer cement (HVGIC); encapsulated GIC; etch and rinse adhesive + composite; self-etch adhesive + composite; preformed stainless steel crown; HVGIC + etch and rinse adhesive + composite; HVGIC + self-etch adhesive + composite, and encapsulated GIC + etch and rinse adhesive + composite. Effectiveness data were sourced from the literature. Micro-costing was applied using 2022 USD market averages with a 5% variation. Incremental cost-effectiveness ratio (ICER), net monetary benefit (%NMB), and the budgetary impact were obtained. RESULTS: Cost-effective treatments included HVGIC (%NMB = 0%/ 0%), encapsulated GIC (%NMB = 19.4%/ 19.7%), and encapsulated GIC + etch and rinse adhesive + composite (%NMB = 23.4%/ 24.5%) at 1 year and 10 years, respectively. The benefit gain of encapsulated GIC + etch and rinse adhesive + composite in relation to encapsulated GIC was small when compared to the cost increase at 1 year (gain of 3.28% and increase of USD 24.26) and 10 years (gain of 4% and increase of USD 15.54). CONCLUSION: Within the horizon and perspective analyzed, the most cost-effective treatment was encapsulated GIC restoration. CLINICAL RELEVANCE: This study can provide information for decision-making.

Effect of Bonding Agents on the Shear Bond Strength of Tooth-colored Restorative Materials to Dentin: An In Vitro Study.

AIM: The aim of the study is to determine the difference in the shear bond strengths to dentin among dental composite (Filtek Z350®, 3M), compomer (Dyract Flow®, Dentsply) and Giomer (Beautifil®, Shofu) with 3MTM Single BondTM Universal Adhesive (SBU) (7th generation, self-etch, single solution adhesive) and AdperTM Single Bond 2 Adhesive (ASB) (5th generation, total-etch, two solution adhesive). MATERIALS AND METHODS: Sixty extracted human permanent teeth were collected, cleansed of debris, and placed in distilled water. The samples were segregated into two groups depicting the two bonding agents-AdperTM (ASB) and 3MTM Single Bond Universal (SBU) and sub-grouped into three groups depicting the three restorative materials (Composite, Giomer, and Compomer) used. Groups were respresented as follows: Group I-ASB + Composite; Group II-ASB + Giomer; Group III-ASB + Compomer; Group IV-SBU + Giomer; Group V-SBU + Compomer; Group VI-SBU + Composite. After applying the bonding agent as per the manufacturer's instructions, following which the restorative material was placed. A Universal Testing Machine (Instron 3366, UK) was employed to estimate the shear bond strength of the individual restorative material and shear bond strengths were calculated. RESULTS: Composite bonded with SBU (group VI) displayed the greatest shear strength (11.16 ± 4.22 MPa). Moreover, Giomers and flowable compomers displayed better bond strengths with ASB compared with their SBU-bonded counterparts. CONCLUSION: These results mark the importance of careful material selection in clinical practice and the bonding agent used to achieve optimal bond strength and enhance the clinical longevity and durability of dental restorations. CLINICAL SIGNIFICANCE: From a clinical perspective, to avoid a compressive or a shear failure, it would be preferrable to use a direct composite restorative material with SBU (Single bond universal adhesive, 7th generation) to achieve maximum bond strength. How to cite this article: Kuchibhotla N, Sathyamoorthy H, Balakrishnan S, et al. Effect of Bonding Agents on the Shear Bond Strength of Tooth-colored Restorative Materials to Dentin: An In Vitro Study. J Contemp Dent Pract 2024;25(3):245-249.

Health complaints before and at one and five years after removal of dental amalgam restorations - data from a prospective cohort study in Norway.

OBJECTIVE: Health complaints attributed to dental amalgam fillings comprise both intraoral and general health complaints. There are data suggesting that patients with medically unexplained physical symptoms (MUPS) attributed to amalgam fillings show improvement in symptoms after removal of all amalgam fillings. However, data indicating changes of specific health complaints are limited. This study evaluated the changes of health complaints after removal of amalgam restorations in patients with health complaints attributed to dental amalgam fillings. METHOD: Patients with MUPS attributed to dental amalgam (Amalgam cohort) had all their amalgam fillings removed. The participants indicated an intensity of 11 local and 12 general health complaints on numeric rating scales before the treatment and at follow-up after 1 and 5 years. The comparison groups comprising a group of healthy individuals and a group of patients with MUPS without symptom attribution to dental amalgam did not have their amalgam restorations removed. RESULTS: In the Amalgam cohort, mean symptom intensity was lower for all 23 health complaints at follow-up at 1 year compared to baseline. Statistically significant changes were observed for specific health complaints with effect sizes between 0.36 and 0.68. At the 5-year follow-up, the intensity of symptoms remained consistently lower compared to before the amalgam removal. In the comparison groups, no significant changes of intensity of symptoms of health complaints were observed. CONCLUSION: After removal of all amalgam restorations, both local and general health complaints were reduced. Since blinding of the treatment was not possible, specific and non-specific treatment effects cannot be separated.

[Radiological assessment of long-term outcomes of restorative treatment in patients with shortened dental arches]. / Rentgenologicheskaya otsenka otdalennykh rezul'tatov ortopedicheskogo lecheniya patsientov s ukorochennym zubnym ryadom.

BACKGROUND: Restoring the integrity of the dentition with orthopedic structures should be carried out strictly according to indications, taking into account the condition of the supporting teeth and/or teeth limiting the defect. OBJECTIVE: To conduct a retrospective analysis of the results of orthopedic treatment of patients with shortened dentition according to clinical and radiological methods. MATERIALS AND METHODS: The material for the study was data from cone beam computed tomography (CBCT) of 126 patients with shortened dentition (most patients with the absence of a second molar, as well as the absence of the first and second molars), who sought a consultation about missing teeth in the orthopedic and surgical department of the Federal State Budgetary Institution National Medical Research Center TsNIISiCHLKh Ministry of Health of Russia. RESULTS: At the stages of treatment for patients in the study group, insufficient attention is paid to the restoration of terminal defects of the dentition in the upper and lower jaws, especially the restoration of second molars. This may be due to improper planning of dental treatment and insufficient motivation of the patient to carry out comprehensive dental rehabilitation. According to CT studies, the number of complications of orthopedic treatment in the area of supporting teeth and/or teeth limiting the included defect or terminal defect of the dentition in the masticatory region increases depending on the period of use of the orthopedic structure. CONCLUSIONS: The use of cantilever structures leads to functional overload of the supporting teeth. Neglecting the restoration of a full dentition and prosthetics of end defects of the dentition leads to dentoalveolar advancement of antagonists of missing teeth and the appearance of complications such as functional overload of supporting teeth and resorption of alveolar bone.

Preventive and restorative alternatives to caries by irradiation: a scoping review.

PURPOSE: This study is to conduct a comprehensive scoping review to map scientific evidence and clarify concepts regarding the commonly recommended preventive and restorative dental treatments for patients diagnosed with head and neck cancer (HNC) and subjected to radiotherapy. MATERIAL AND METHODS: This systematic scoping review was performed under the PRISMA-ScR guidelines. The study's experimental design was registered in the Open Science Framework. In vitro studies that evaluated preventive and restorative dental treatment over 50 Gy radiation doses were included. The search was conducted in November 2023 in five electronic databases (PubMed, Scopus, Web of Science, Cochrane Library, and Embase) without language or date restriction. A search strategy was applied based on keywords, MeSh terms, or synonyms. A descriptive analysis was conducted. RESULTS: A total of 49 studies, out of 3679 original articles identified, were included and reviewed. Of the included studies, three evaluated saliva stimulants and 35 evaluated fluoride-based preventive materials: gel (n = 18) toothpaste (n = 11) mouth rinse (n = 8) and varnish (n = 5) while 14 evaluated restorative materials: resin composite (n = 12) glass ionomer cement (n = 6) and amalgam (n = 1) Of those studies, 36 were clinical trials and 13 were in vitro studies. CONCLUSION: Fluoride gel was the most frequently recommended preventive material for preventing radiation caries with supportive clinical evidence. Resin composite and glass ionomer were the most frequently used restorative materials, respectively. However, there is not yet clinical evidence to support the use of resin composite in irradiated teeth.

Preventive management of carious lesions: from non-invasive to micro-invasive operative interventions.

Understanding that dental carious lesions occur as a result of the action of micro-organisms in the dental plaque biofilm, where demineralisation on the tooth surface is the first sign of the disease, such incipient lesions can be treated using preventive, non-operative and minimally invasive operative dentistry. If the caries process is left unmanaged, the lesions progress towards cavitation, leading to more invasive treatments. This article discusses the principles of preventive, non-invasive and micro-invasive treatments of early carious lesions, outlining the clinical situations where these therapies can be applied.

A quantitative and qualitative investigation into the management of carious primary molars by foundation dentists in primary care in the South East of England.

Introduction Dental caries is the most common reason for hospital admission of children aged 5-9 in the UK. Better management of caries in primary molars would reduce the number of children requiring treatment in hospitals; however, little research has been done into why primary care clinicians do not use an evidence-based approach to caries management for deciduous molars.Aims The aim of this paper is to identify the rationale behind caries management techniques used in primary care, as well as the choice of materials and long-term success of restorations placed.Materials and methods Use of a retrospective audit and a focus group with primary care clinicians to provide an insight into the management of carious primary molars and the barriers to achieving gold standard care.Results Glass ionomer cements (GICs) were the restoration of choice in primary care. Lack of time, equipment availability and clinician inexperience were cited as to why Hall crowns were not commonly placed.Conclusions The barriers to gold standard management of carious primary molars in practice are wide-ranging but tend to focus on the limitations of NHS care under the units of dental activity system. Lack of time and cost of materials encouraged clinicians to adopt a 'quick fix' approach in GIC.

Restoration of Complicated Crown-Root Fracture in a Primary Incisor with Fragment Reattachment.

In traumatic dental injuries in children, due to a lack of maturity to cope with the situation, pain intolerance, amount of treatment procedure, and parental anxiety, simplified and non-invasive treatment procedures, such as biologic restorations, are useful. Using advanced adhesive material for fragment reattachment provides excellent esthetic results and a positive attitude from the patient and family. The purpose of this case report is to describe the biological restoration of a complicated crown-root fracture of a primary maxillary central incisor with the fragment reattachment technique.

Impact of repeated preheating of bulk-fill resin composite on postoperative hypersensitivity; a randomized controlled clinical trial.

BACKGROUND: This clinical study was conducted aiming to evaluate the impact of repeated preheating of bulk-fill resin composite on postoperative hypersensitivity. METHODS: A total of 105 eligible, consenting adults were recruited. Patients had posterior teeth suffering from proximal decay with no signs of irreversible pulpitis. Patients were prepared for Class II restorations and restored with bulk-fill resin composite. Patients were randomized into three groups of 35 patients according to the number of preheating cycles for the resin composite syringe used; group I: no preheating; control group at room temperature, group II: Resin composite preheated once, and group III: Resin composite preheated ten cycles. Patients were assessed for postoperative dentin hypersensitivity using the visual analogue scale (VAS) at three-time intervals: day one, one week and by the end of one month after restorative treatment. Statistical analysis was performed; ANOVA with a single factor was used to test for significance at a p value ≤ 0.05. For nonparametric data, the Kruskal‒Wallis test was used to compare the three testing groups. Friedman's test was used to study the changes within each group. Dunn's test was used for pairwise comparisons when the Kruskal‒Wallis test or Friedman's test was significant. RESULTS: The scores of the three groups through the three time intervals were almost zero except for the first day where VAS scores were recorded with maximum score of 3 for groups I and II. Groups II and III; there was no statistically significant change in hypersensitivity scores by time with P-values 0.135 and 0.368, respectively. However, for group I there was a significant difference from VAS score recorded on first day and the two following time intervals. CONCLUSION: The repeated preheating cycles of bulk-fill resin composite prior to curing had no adverse effect on the patients regarding postoperative dentin hypersensitivity. This information could be of utmost significance, as the same resin composite syringe can undergo numerous preheating cycles clinically before it is completely consumed with the advantage of improvement on the handling properties. TRIAL REGISTRATION: The protocol of the current study was registered at www. CLINICALTRIALS: gov , with the identification number NCT05289479 on 21/03/2022. All procedures involving human participants were performed in accordance with the ethical standards of the Research Ethics Committee of the Faculty of Dentistry, Minia University, Egypt, under the approval number 73/440 on 11/09/2020.

Deep Margin Elevation - A Retrospective Clinical Study.

PURPOSE: The aim of this retrospective study was to assess the short- to mid-term restorative and periodontal outcome of deep margin elevation (DME) performed using resin composite. MATERIALS AND METHODS: Twenty-eight teeth treated with DME and indirect adhesive restorations were followed-up for a mean of 25.4 months (minimum: 12 months). Clinical and radiographic examination assessed the adaptation of the DME material and indirect restorations, presence of recurrent caries or discoloration, periodontal health at DME and non-DME sites, and periapical health. RESULTS: The overall success rate was 96.6%. One tooth showed signs and symptoms of apical pathology after 34 months following DME. No caries, discoloration, or periodontal pockets were detected in any of the treated teeth. DME had no detrimental effect on the gingival/periodontal health or plaque accumulation. There was no correlation between the distance from the DME material to the marginal bone level and pocket depth, gingival inflammation, and plaque accumulation (p > 0.05). CONCLUSION: Deep margin elevation might be considered a safe procedure for teeth with deep subgingival proximal caries in the short- and mid-term.

Evaluation of Retentive Strength of 50 Endodontically-Treated Single-Rooted Mandibular Second Premolars Restored with Cast Post Cores Using 5 Common Luting (Cement) Agents.

BACKGROUND A luting agent is a dental cement used to secure a dental restoration. This study aimed to evaluate retentive strength of 50 endodontically-treated single-rooted mandibular second premolars (extracted) restored using 5 common luting (cement) agents. MATERIAL AND METHODS Fifty single-rooted mandibular second premolars with adequate root length and uniform size/shape were decoronated. After completing endodontic biomechanical preparation and obturation, root canals of all specimens were prepared to receive a cast post core. Depending upon cementation type, CPC specimens were divided in 5 groups (10 each) (Gp): Zinc phosphate (Gp ZP), polycarboxylate (Gp PC), glass ionomer (Gp GI), resin-modified glass ionomer (Gp RGI), and resin cement (Gp RC). Retentive strength was determined using the adhesive failure pull-out test. Mean/standard deviations were calculated for tensile forces (in kilograms) and differences were determined using analysis of variance (ANOVA). Multiple comparison was performed using the t test. A P value of ≤0.05 indicated a statistically significant difference. RESULTS The order of mean tensile strength from higher to lower was Gp RC (21.46) >Gp RGI (18.17) >Gp GI (16.07) >Gp ZP (15.33) >Gp PC (13.63). Differences in retentive strengths between the cements were significant (P≤0.05). Multiple-group comparisons showed that except for Gp ZP and Gp GI, all groups differed significantly from each other. CONCLUSIONS All investigated cements provided optimal retentive strengths, with wide differences between them. Resin cements should be used when CPC removal is not anticipated, while polycarboxylate or zinc phosphate should be used if CPC removal is anticipated.

Effect of various surface coating methods on surface roughness, micromorphological analysis and fluoride release from contemporary glass ionomer restorations.

OBJECTIVE: To evaluate the effect of various surface coating methods on surface roughness, micromorphological analysis and fluoride release from contemporary resin-modified and conventional glass ionomer restorations. MATERIALS & METHODS: A total of 72 permanent human molars were used in this study. The teeth were randomly assigned into 2 groups according to type of restorative materials used; resin modified glass ionomer cement and conventional glass ionomer (SDI Limited. Bayswater Victoria, Australia). Each group was subdivided into 3 subgroups according to the application of coat material; Sub-group1: without application of coat; Sub-group2: manufacturer recommended coat was applied and sub-group3: customized (vaseline) coat was applied. Each group was then subdivided into two divisions according to the time of testing; immediate (after 24 h) and delayed (after 6 months of storage). Three specimens from each sub-group were selected for surface roughness test (AFM) and another 3 specimens for the micromorphological analysis using scanning electron microscope (SEM). For the fluoride release test, a total of 60 cylindrical discs were used (n = 60). The discs were randomly split into 2 groups according to type of restorative materials used (n = 30); resin modified glass ionomer cement and conventional glass ionomer. Each group was subdivided into 3 subgroups (n = 10) according to the application of the coat material; Sub-group1: without application of coat; Sub-group2: with the manufacturer recommended coat and sub-group3: with application of customized (vaseline) coat. Data for each test was then collected, tabulated, were collected, tabulated, and tested for the normality with Shapiro-Wilk test. Based on the outcome of normality test, the significant effects of variables were assessed using appropriate statistical analysis testing methods. RESULTS: Regarding the data obtained from surface roughness test, Shapiro-Wilk test showed normal distribution pattern of all values (p > 0.05). Accordingly, Two-way ANOVA outcome showed that the 'type of restoration' or 'test time' had statistically significant effect on the AFM test (p < 0.05). Regarding Fluoride specific ion electrode test 2-way ANOVA followed by Least Significant Difference (LSD) Post-hoc test revealed significant difference among the groups (p < 0.05). It showed that SDI GIC group after 14 days of measurement had the highest mean of fluoride release (36.38 ± 3.16 PPM) and SDI RMGIC after 30 days of measurement had the second highest mean of fluoride release (43.28 ± 1.89 PPM). Finally, regarding the micromorphological analysis using SEM, a slight difference was observed between the studied groups. CONCLUSIONS: Based on the results of this study, various coatings enhance surface roughness in the initial 24 h of restoration insertion. Different coat types seems that have no influence on fluoride release and the micromorphological features of the restoration/dentin interface.

Influence of CAD-CAM milling strategies on the outcome of indirect restorations: A scoping review.

STATEMENT OF PROBLEM: The influence of computer-aided manufacturing (CAM) parameters and settings on the outcomes of milled indirect restorations is poorly understood. PURPOSE: The purpose of this scoping review was to summarize the current CAM systems, parameters, and setting changes, and their effects on different outcomes of milled indirect restorations and aspects related to their manufacture. MATERIAL AND METHODS: The protocol of this review is available online (https://osf.io/x28ps/). Studies that used at least 2 different parameters (CAM units, number of axes, digital spacers, or protocols with different rotatory instruments, grit-sizes, milling speed, or others) for milling indirect restorations were included. A structured search up to July 2023 was performed by 2 independent reviewers for articles written in English in LILACS, MEDLINE via PubMed, EMBASE, Web of Science, and Scopus. RESULTS: Of 1546 studies identified, 22 were included in the review. Discrepancies were found between the planned and actual measured cement space, with a decreasing linear relationship impacting restoration adaptation at different points. The CEREC MC XL milling machine was the most used system in the included studies, with variations in bur types, milling modes, and number of burs uses affecting internal fit and surface trueness. The results demonstrated the better adaptation of restorations made with 5-axis over 3-axis milling machines. Lithium disilicate and zirconia were the most commonly used materials, and crowns and inlays were popular designs. Marginal and internal adaptation were the primary outcomes assessed using the various techniques. CONCLUSIONS: The study presented a comprehensive exploration of CAM systems and parameters, and their influence on indirect restorations. The planned cement space was not properly reproduced by the milling. Bur characteristics can affect restoration fit and trueness. The 5-axis units seem to result in better-adapted restorations compared with 3- and 4-axis units.

Influence of different immediate dentin sealing strategies on bond strength of indirect resin nanoceramic restorations.

In this study, we evaluated the effect of four different strategies for bonding a CAD/CAM resin nanoceramic restoration (Lava Ultimate, 3M) to the dentin surface using a universal adhesive (Scotch Bond Universal, 3M) and adhesive resin cement (RelyX Ultimate, 3M) on the shear bond strength (SBS) and failure mode. The strategies comprised: (i) immediate sealing, immediate bonding; (ii) immediate sealing, bonding after 2 weeks with provisional restoration; (iii) immediate sealing with flowable resin composite reinforcement and bonding after 2 weeks with provisional restoration; and (iv) no immediate sealing, and bonding after 2 weeks with provisional restoration. After bonding, all the specimens were thermocycled, shear tests were performed using a universal testing machine, and failure modes were determined using stereomicroscope and scanning electron microscopy. The highest mean SBS was recorded with immediate sealing, immediate bonding strategy. Most adhesive failures with exposed dentinal tubules were noted in specimens exposed to bonding after 2 weeks with no immediate sealing, which was associated with the lowest SBS. Mixed failures predominated in all immediate dentin sealing groups. Immediate sealing with universal adhesives improves SBS, particularly in the single-visit approach, which has shown significantly better performance, whereas the provisional phase has a negative effect.

The clinical performance of dental resin composite repeatedly preheated: A randomized controlled clinical trial.

OBJECTIVES: To assess the clinical performance of class II restorations performed by repeatedly preheated resin composite "RC" at 68 °C up to ten times. METHODS: 105 patients were selected and randomized into three groups, each comprising 35 patients. Each patient was provided with a single class II Bulk-fill resin composite "BF-RC" posterior restoration based on the number of preheating cycles; group I (H0): The BF-RC was packed non-heated, group II (H1): BF-RC preheated once, and group III(H10): BF-RC preheated ten cycles. These restorations were evaluated at 1, 3,6, and 12 months, using the modified United States Public Health Service "USPHS". Statistical analysis was performed using Kruskal-Wallis test, Mann Whitney U test, and Friedmann test, where p = 0.05. RESULTS: All the 105 restorations did not suffer from any clinical situation that recommended replacement regarding retention, fracture, secondary caries, or anatomical form. Although all performed restorations did have Alpha and Bravo scores with good clinical performance, the non-preheated RC restorations"" suffered from relatively inferior clinical performance through the follow-up period regarding marginal adaptation, marginal discoloration, and color matching when compared to preheated groups. One and ten times of preheating conducted better clinical performance. CONCLUSIONS: After 12-months follow-up, although no restoration needed replacement or repair in the 3 tested groups, restorations with single and ten times of preheating aided in better clinical performance of RC restorations compared to the non-preheated restorations. Preheating of RC for 10 times could be used safely with good clinical performance of restorations. CLINICAL SIGNIFICANCE: By continually preheating RC syringe up to ten times, the dentist will not only benefit from the enhanced clinical performance and easiness of application but also will use preheated RC syringes without hesitation, relying on the absence of drawbacks related to multiple preheating cycles.

In Vitro Microleakage and Fracture Resistance of "Infinity Edge" and Cusp Reduction Preparation Designs for Moderate-sized Class II Composites.

AIM: This study aimed to evaluate the marginal microleakage and maximum occlusal fracture loads and fracture modes of two novel class II preparation designs, "infinity edge" and the "2.5 mm cusp reduction" preparations as compared to a traditional class II preparation without cuspal involvement. MATERIALS AND METHODS: Thirty extracted human mandibular molars were prepared for moderate-sized class II restorations with extensions into all occlusal grooves. Of these, ten class II preparations served as control. Ten were modified for a 2.5 mm even reduction of the cusps adjacent to the interproximal box. An additional 10 preparations were modified with an "infinity edge" bevel on the interproximal and occlusal portions. All teeth were restored utilizing a flowable bulk-fill composite in the apical portion of the interproximal box and 2-4 mm of heated bulk-fill composite in one increment for the remainder. All groups were cyclic loaded and thermocycled, then imaged with microcomputed tomography (µCT) before and after infiltration with a silver nitrate solution. Images were subtracted to obtain volumetric measurements of microleakage and reported as a percentage of the total volume from the apical extent of the proximal box. All groups were loaded to failure and fracture load and mode were recorded. RESULTS: No significant differences were found in microleakage volume as a percentage of total tooth volume; however, the "infinity edge" group had significantly greater microleakage in the proximal box compared to the traditional class II group. No significant differences were found in fracture load or mode between the groups. CONCLUSION: Traditional class II, 2.5 mm cuspal reduction, and "infinity edge" preparation designs have similar fracture loads as well as volumes of microleakage; however, an "infinity edge" preparation has a higher ratio of microleakage in the proximal box. CLINICAL SIGNIFICANCE: Clinicians should carefully consider the use of "infinity edge" margins, particularly on dentin in the apical extent of the proximal box. How to cite this article: Watson JC, Lien W, Raimondi JC, et al. In Vitro Microleakage and Fracture Resistance of "Infinity Edge" and Cusp Reduction Preparation Designs for Moderate-sized Class II Composites. J Contemp Dent Pract 2024;25(1):3-9.

Comparative Assessment of Marginal Micro Leakage of Different Esthetic Restorative Materials Used on Primary Teeth: An In-vitro Study.

AIM: The aim of the current investigation was to evaluate the marginal microleakage of various esthetic restorative materials applied to primary teeth. MATERIALS AND METHODS: A total of 75 noncarious primary molars that were removed for orthodontic intervention and teeth nearing exfoliation were chosen. One millimeter (mm) above the cementoenamel junction, on the buccal surface of the teeth, Class V cavities were prepared. William's graded periodontal probe was used to standardize cavity preparation on all teeth. 3 mm was the cavity's length, 2 mm in width, and 2 mm in depth. The teeth were then divided into three groups (25 samples in each group) according to the type of esthetic restorative material used. Group I: Resin-modified glass ionomer cement, Group II: Ormocer, Group III: Giomer. The samples underwent 500 cycles of thermocycling, with an immersion time of 60 seconds and a well time of 15 seconds, between 5 and 55°C. The samples were submerged in methylene blue dye for 24 hours at room temperature and dried. The samples were then divided into sections and examined with a stereomicroscope. Data was recorded and statistically analyzed. RESULTS: The least marginal microleakage was found in the ormocer group (1.22 ± 0.01) followed by resin-modified glass ionomer cement group (1.31 ± 0.07) and the giomer group (1.78 ± 0.03). There was a highly statistically significant difference found between resin-modified glass ionomer cement group and the ormocer group, resin-modified glass ionomer cement group and giomer group. And no significant difference was found between the ormocer group and the giomer group. CONCLUSION: The present study concluded that there was some amount of microleakage in primary teeth in all restorative materials examined in this in-vitro investigation. However, the marginal sealing ability of ormocer was found highest compared to resin-modified glass ionomer cement and Giomer materials. CLINICAL SIGNIFICANCE: The primary reason dental restorations fail, particularly in Class V cavities, is microleakage since the margins of these restorations are typically found in the dentin or cementum. Assessing microleakage is a crucial step in determining the marginal integrity of restorative materials. Developing methods and resources that reduce the adverse effects caused by the restorative marginal seal failing would benefit from this. How to cite this article: Al Ghwainem A, Alqarni AS. Comparative Assessment of Marginal Micro Leakage of Different Esthetic Restorative Materials Used on Primary Teeth: An In-vitro Study. J Contemp Dent Pract 2024;25(1):58-61.

Effect of composite radiopacity and margin location of the restoration on the diagnosis of secondary caries.

This research aimed to evaluate the effect of the radiopacity of a Bulk-Fill composite (X-TraFil, VOCO, Germany) and a Conventional composite (P60, 3M ESPE, USA) and assessment of the margin location in the enamel and dentin on the diagnosis of secondary caries. 76 intact premolars with MOD preparation were divided into two equal groups and filled with the conventional and bulk-fill composite. Four regions were considered to simulate carious lesions (two regions in enamel and two regions in dentin). In each group, half of the regions in the dentin and half in the enamel were randomly selected for secondary caries simulation and filled with a wax-plaster combination while the remaining regions stayed intact. Bitewing imaging was done using the PSP digital sensor. Five examiners reviewed the images, and lesions were recorded. Caries diagnosis indicators and paired-sample t-test were used for statistical analysis. The reproducibility and accuracy of the examiners' responses were evaluated using the kappa and agreement coefficient (α=0.05). The sensitivity, specificity, and accuracy of diagnosing secondary carious lesions in enamel were significantly better under conventional than bulk-fill composite. Similarly, the sensitivity and accuracy of diagnosing secondary caries in dentin were significantly higher under conventional composite than bulk-fill composite (p<0.05). No significant differences were found in the agreement and kappa coefficient between conventional and bulk-fill composites in the enamel and dentin (p>0.05). The diagnostic accuracy of carious lesions was higher under conventional composite than bulk-fill composite. However, the location of the secondary was ineffective in caries diagnosis.

Clinical evaluation of resorbable polylactic acid (PLA) intracanal posts for primary incisor restoration. Randomized controlled clinical trial.

This randomized, controlled clinical trial compares the clinical performance of glass-fibre and resorbable polylactic acid (PLA) intracanal posts used to restore carious primary incisors in young patients. The study sample includes 180 primary upper central incisors of 90 children aged 3 to 4 years. All patients were randomly divided into two equal groups of 45 children who received PLA and glass-fibre (GFP) intracanal posts. The clinical assessment of incisor restorations was carried out immediately upon completion and at months 3, 6 and 12 according to the following criteria: anatomical form, marginal adaptation, surface roughness, marginal pigmentation, colour match, secondary caries and contact point. The Gingival Index (GI), the Bleeding Index (Cowell modification; mBI), and bite force (BF) were measured. At the 3-month follow-up, the occlusal BF of patients who received PLA posts was higher than the baseline; the GI and mBI scores were lower, by contrast (p < 0.05). This tendency was even more pronounced 6 and 12 months after the restoration. The incidence of side effects or symptoms (apical inflammation, cervical fracture, loosening of the crown) after the PLA posts was significantly lower than after the GFP (p < 0.05). No statistically significant differences were present between the two groups with respect to colour matching, anatomical form, marginal adaptation, marginal pigmentation, surface roughness, occlusal contact and secondary caries. Based on the results, applying PLA intracanal posts and cyanoacrylate to residual anterior crowns in young children can improve their gingival health, reduce side effects, and increase the likelihood of successful restoration.