Unambiguous identification of γ-aminobutyric acid adducts as novel plant biomarkers and their ultra-sensitive detection by UPLC-MS/MS for retrospective analyses of nitrogen mustards exposure.

Plants are widely existing in the environments and have been considered as potential sentinel species of toxic chemicals' exposure. In this study, the deadly toxic chemicals of three nitrogen mustards (NMs, including NH1, NH2 and NH3) were selected as the investigated targets. First, the reactivities of common endogenous plant components with NMs were examined in vitro. Then, the model plant Nicotiana benthamiana Domin was exposed to NMs. Three γ-aminobutyric acid-nitrogen mustard adducts (GABA-NMs) were identified in the living plant by high resolution mass spectrometry and comparison with the synthesized references. A sensitive detection method with the limits of quantification of 0.0500 ng mL-1 was developed using ultrahigh performance liquid chromatography-triple quadrupole mass spectrometry. The GABA-NMs could be detected after 120 days of the exposure and even in the dead leaves without obvious decrease. Furthermore, 20 different plant species grown in diverse climate zones were exposed to HN1, and the adduct of GABA-HN1 was identified in all the leaves. The results showed the good universality and specificity of GABA-NMs as plant biomarkers for NMs exposure. This work provides a new approach for the pollution investigation of toxic chemicals through analysing biomarkers in plant materials.

Ethanolysis of nitrogen mustards: A novel strategy for nitrogen mustard identification in environmental matrices by liquid chromatography-electrospray ionization-tandem mass spectrometry.

RATIONALE: Nitrogen mustards (NMs) are blistering chemical warfare agents. The ability to detect NMs in environmental samples is very important for obtaining forensic evidence. The most common analytical techniques for NM detection are gas chromatography-mass spectrometry, which detects NMs in their intact form but is disadvantaged by high limits of detection (LODs), and liquid chromatography-electrospray ionization-tandem mass spectrometry (LC/ESI-MS/MS) of their hydrolysis products, which do not provide robust evidence to support NM use. METHODS: We developed a novel approach to detect and identify NMs using LC/ESI-MS/MS after chemical derivatization. The method is based on ethoxide-promoted ethanolysis prior to analysis. The effects of reaction time, temperature, ethoxide concentration and chromatography behavior were studied and optimized. In the developed procedure, 0.1% (v/v) sodium ethoxide solution is added to the NMs in ethanol and agitated for 2 h at 50°C, followed by LC/ESI-MS/MS, without any other pretreatment. RESULTS: The ethanolysis reaction efficiencies were evaluated in ethanolic extracts from soil, asphalt, and ethanol contaminated with 0.5% (v/v) diesel fortified with NMs at a five-point calibration curve. The calibration curves showed good linearity in the range of 0.05-1 ng/mL, with an R2 value of 0.99, and were similar to those of LC/MS-grade ethanol, with almost no observable matrix effects. The derivatization products were stable at room temperature, with LODs of 10 pg/mL, in all investigated extracts. CONCLUSIONS: Through this newly developed strategy, the derivatization of active NMs by ethanolysis was achieved for the first time, and these derivatization products can serve as specific indicators for the use and presence of NMs. The methodology can also verify trace levels of NM chemical warfare agents collected in war or terror scenarios in forensic investigations.

Analysis of nitrogen mustard degradation products via post-pentafluorobenzoylation liquid chromatography-tandem mass spectrometry.

A pentafluorobenzoylation (PFBz)-liquid chromatography-tandem mass spectrometry method was developed for qualitative and quantitative analysis of ethanolamines (EAs, nitrogen mustard degradation products). With this method, highly hydrophilic EAs can be sufficiently analyzed with a commonly used reversed phase column (retention times: (PFBz)2-methyl diethanolamine, 9.1 min; (PFBz)2-ethyl diethanolamine, 9.8 min; and (PFBz)3-triethanolamine, 17.6 min). The applicability of the method for real samples was investigated via recovery tests. Methyl diethanolamine and ethyl diethanolamine were detected at concentrations as low as 1 ng/mL in serum and 10 ng/mL in urine, and quantified within the range of 1-1000 ng/mL and 10-1000 ng/mL, respectively.

Mass spectral studies of silyl derivatives of partially hydrolyzed products of nitrogen mustards: Important markers of nitrogen mustard exposure.

RATIONALE: Nitrogen mustards (NMs) are vesicant class of chemical warfare agents. From the viewpoint of the Chemical Weapons Convention partially hydrolyzed products of nitrogen mustards (pHpNMs) are considered as important markers of nitrogen mustard exposure. The detection of pHpNMs from biological or environmental samples is highly useful for obtaining forensic evidence of exposure to NMs. METHODS: Gas chromatography interfaced with tandem mass spectrometry (GC/MS/MS) is a widely used tool for the identification and sensitive detection of metabolites of NMs in complex matrices. The pHpNMs were derivatized using silylating agents as they are highly polar and non-amenable to GC. The mass spectral studies of these silyl derivatives of pHpNMs were performed using GC/MS/MS in both electron ionization (EI) and chemical ionization (CI) mode. RESULTS: Various approaches have been proposed to assess the fragmentation pathways of the trimethylsilyl (TMS) and tert-butyldimethylsilyl (TBDMS) derivatives of pHpNMs. All the proposed fragmentation pathways were based on the product and/or precursor ion scanning of corresponding ions in both EI and CI mode. In the case of EI, most of the fragmentation pathways involved either α-cleavage or inductive cleavage. CONCLUSIONS: This is the first report on the MS study of the silyl derivatives of pHpNMs. The study of the two different derivatives of pHpNMs using both EI- and CI-MS provides a reliable, unambiguous identification of pHpNMs in complex environmental and biomedical matrices (such as plasma and urine) during any verification activities.

Analysis of degradation products of nitrogen mustards via hydrophilic interaction liquid chromatography-tandem mass spectrometry.

A hydrophilic interaction liquid chromatography-tandem mass spectrometry (HILIC-MS/MS) method was developed for qualitative and quantitative analysis of ethanolamines (EAs), which are nitrogen mustard degradation products. With this method, the retention times of the highly hydrophilic EAs on the HILIC column were sufficient (retention times: methyl diethanolamine, 12.2 min; ethyl diethanolamine, 11.2 min; and triethanolamine, 9.5 min) and the EAs were analyzed more efficiently than with reported HILIC-MS/MS methods. The detection limits of methyl diethanolamine and ethyl diethanolamine in serum and urine using this approach were 15-20 ng/mL. The suitability of the method for real samples was evaluated via recovery tests involving urine and serum, and the method was validated. The MS/MS fragmentation of EAs was discussed based on density functional theory calculations.

Identification of chemical warfare agents from vapor samples using a field-portable capillary gas chromatography/membrane-interfaced electron ionization quadrupole mass spectrometry instrument with Tri-Bed concentrator.

A field-portable gas chromatograph-mass spectrometer (Hapsite ER system) was evaluated for the detection of chemical warfare agents (CWAs) in the vapor phase. The system consisted of Tri-Bed concentrator gas sampler (trapping time: 3s(-1)min), a nonpolar low thermal-mass capillary gas chromatography column capable of raising temperatures up to 200°C, a hydrophobic membrane-interfaced electron ionization quadrupole mass spectrometer evacuated by a non-evaporative getter pump for data acquisition, and a personal computer for data analysis. Sample vapors containing as little as 22µg sarin (GB), 100µg soman (GD), 210µg tabun (GA), 55µg cyclohexylsarin (GF), 4.8µg sulfur mustard, 390µg nitrogen mustard 1, 140µg of nitrogen mustard 2, 130µg nitrogen mustard 3, 120µg of 2-chloroacetophenone and 990µg of chloropicrin per cubic meter could be confirmed after Tri-Bed micro-concentration (for 1min) and automated AMDIS search within 12min. Using manual deconvolution by background subtraction of neighboring regions on the extracted ion chromatograms, the above-mentioned CWAs could be confirmed at lower concentration levels. The memory effects were also examined and we found that blister agents showed significantly more carry-over than nerve agents. Gasoline vapor was found to interfere with the detection of GB and GD, raising the concentration limits for confirmation in the presence of gasoline by both AMDIS search and manual deconvolution; however, GA and GF were not subject to interference by gasoline. Lewisite 1, and o-chlorobenzylidene malononitrile could also be confirmed by gas chromatography, but it was hard to quantify them. Vapors of phosgene, chlorine, and cyanogen chloride could be confirmed by direct mass spectrometric detection at concentration levels higher than 2, 140, and 10mg/m(3) respectively, by bypassing the micro-concentration trap and gas chromatographic separation.

Rapid screening of N-oxides of chemical warfare agents degradation products by ESI-tandem mass spectrometry.

Rapid detection and identification of chemical warfare agents and related precursors/degradation products in various environmental matrices is of paramount importance for verification of standards set by the chemical weapons convention (CWC). Nitrogen mustards, N,N-dialkylaminoethyl-2-chlorides, N,N-dialkylaminoethanols, N-alkyldiethanolamines, and triethanolamine, which are listed CWC scheduled chemicals, are prone to undergo N-oxidation in environmental matrices or during decontamination process. Thus, screening of the oxidized products of these compounds is also an important task in the verification process because the presence of these products reveals alleged use of nitrogen mustards or precursors of VX compounds. The N-oxides of aminoethanols and aminoethylchlorides easily produce [M + H](+) ions under electrospray ionization conditions, and their collision-induced dissociation spectra include a specific neutral loss of 48 u (OH + CH2OH) and 66 u (OH + CH2Cl), respectively. Based on this specific fragmentation, a rapid screening method was developed for screening of the N-oxides by applying neutral loss scan technique. The method was validated and the applicability of the method was demonstrated by analyzing positive and negative samples. The method was useful in the detection of N-oxides of aminoethanols and aminoethylchlorides in environmental matrices at trace levels (LOD, up to 500 ppb), even in the presence of complex masking agents, without the use of time-consuming sample preparation methods and chromatographic steps. This method is advantageous for the off-site verification program and also for participation in official proficiency tests conducted by the Organization for the Prohibition of Chemical Weapons (OPCW), the Netherlands. The structure of N-oxides can be confirmed by the MS/MS experiments on the detected peaks. A liquid chromatography-mass spectrometry (LC-MS) method was developed for the separation of isomeric N-oxides of aminoethanols and aminoethylchlorides using a C18 Hilic column. Critical isomeric compounds can be confirmed by LC-MS/MS experiments, after detecting the N-oxides from the neutral loss scanning method.

Characterization of an array of Love-wave gas sensors developed using electrospinning technique to deposit nanofibers as sensitive layers.

The electrospinning technique has allowed that very different materials are deposited as sensitive layers on Love-wave devices forming a low cost and successful sensor array. Their excellent sensitivity, good linearity and short response time are reported in this paper. Several materials have been used to produce the nanofibers: polymers as Polyvinyl alcohol (PVA), Polyvinylpyrrolidone (PVP) and Polystirene (PS); composites with polymers as PVA+SnCl4; combined polymers as PS+Poly(styrene-alt-maleic anhydride) (PS+PSMA) and metal oxides (SnO2). In order to test the array, well-known chemical warfare agent simulants (CWAs) have been chosen among the volatile organic compounds due to their importance in the security field. Very low concentrations of these compounds have been detected by the array, such as 0.2 ppm of DMMP, a simulant of sarin nerve gas, and 1 ppm of DPGME, a simulant of nitrogen mustard. Additionally, the CWA simulants used in the experiment have been discriminated and classified using pattern recognition techniques, such as principal component analysis and artificial neural networks.

Modified immunoslotblot assay to detect hemi and sulfur mustard DNA adducts.

Sulfur mustard (SM) is an old chemical warfare agent causing blisters (vesicant). Skin toxicity is thought to be partly caused by SM induced DNA damage. SM and the hemi mustard 2-chloroethyl ethyl sulfide (CEES) are bi- and monofunctional DNA alkylating agents, respectively. Both chemicals react especially with N7 guanine. The most abundant adducts are 7-hydroxyethylthioethylguanine for SM (61%) and 7-ethyl thioethylguanine for CEES. Thus, DNA alkylation should serve as a biomarker of SM exposure. A specific monoclonal antibody (2F8) was previously developed to detect SM and CEES adducts at N7 position by means of immunoslotblot (ISB) technique (van der Schans et al. (2004) [16]). Nitrogen mustards (HN-1, HN-2, HN-3) are alkylating agents with structural similarities, which can form DNA adducts with N7 guanine. The aim of the presented work was to modify the van der Schans protocol for use in a field laboratory and to test the cross reactivity of the 2F8 antibody against nitrogen mustards. Briefly, human keratinocytes were exposed to SM and CEES (0-300µM, 60min) or HN-1, HN-2, HN-3 (120min). After exposure, cells were scraped and DNA was isolated and normalized. 1µg DNA was transferred to a nitrocellulose membrane using a slotblot technique. After incubation with 2F8 antibody, the DNA adducts were visualized with chromogen staining (3,3'-diaminobenzidine (DAB), SeramunGrün). Blots were photographed and signal intensity was quantified. In general, DAB was superior to SeramunGrün stain. A staining was seen from 30nM to 300µM of SM or CEES, respectively. However, statistically significant DNA adducts were detected after CEES and SM exposure above 30µM which is below the vesicant threshold. No signal was observed after HN-1, HN-2, HN-3 exposure. The total hands-on time to complete the assay was about 36h. Further studies are necessary to validate SM or CEES exposure in blister roofs of exposed patients.

Determination of nitrogen mustard degradation products in water samples using a portable capillary electrophoresis instrument.

In this work, a new purpose-made portable CE instrument with a contactless conductivity detector was used for the determination of degradation products of nitrogen mustards in different water samples. The capillary was coated with poly(1-vinylpyrrolidone-co-2-dimethylaminoethyl methacrylate) to avoid analyte-wall interactions. The coating procedure was studied to obtain the best repeatability of the migration time of the analytes. Four different coating procedures were compared; flushing the capillary with the copolymer at 100 psi for 2 min at 60°C provided the best RSD values (<4%). The analytical method was also optimized. The use of 20 mM of MES adjusted to pH 6.0 with His as running buffer allowed a good baseline separation of the three analytes in different water samples without matrix interferences. The method permitted the detection of the three degradation products down to 5 µM.

Wipe selection for the analysis of surface materials containing chemical warfare agent nitrogen mustard degradation products by ultra-high pressure liquid chromatography-tandem mass spectrometry.

Degradation products arising from nitrogen mustard chemical warfare agent were deposited on common urban surfaces and determined via surface wiping, wipe extraction, and liquid chromatography­tandem mass spectrometry detection. Wipes investigated included cotton gauze, glass fiber filter, non-woven polyester fiber and filter paper, and surfaces included several porous (vinyl tile, painted drywall, wood) and mostly non-porous (laminate, galvanized steel, glass) surfaces. Wipe extracts were analyzed by ultra-high pressure liquid chromatography­tandem mass spectrometry (UPLC­MS/MS) and compared with high performance liquid chromatography­tandem mass spectrometry (HPLC­MS/MS) results. An evaluation of both techniques suggests UPLC­MS/MS provides a quick and sensitive analysis of targeted degradation products in addition to being nearly four times faster than a single HPLC run, allowing for greater throughput during a wide-spread release concerning large-scale contamination and subsequent remediation events. Based on the overall performance of all tested wipes, filter paper wipes were selected over other wipes because they did not contain interferences or native species (TEA and DEA) associated with the target analytes, resulting in high percent recoveries and low background levels during sample analysis. Other wipes, including cotton gauze, would require a pre-cleaning step due to the presence of large quantities of native species or interferences of the targeted analytes. Percent recoveries obtained from a laminate surface were 47­99% for all nitrogen mustard degradation products. The resulting detection limits achieved from wipes were 0.2 ng/cm(2) for triethanolamine (TEA), 0.03 ng/cm(2) for N-ethyldiethanolamine (EDEA), 0.1 ng/cm(2) for N-methyldiethanolamine (MDEA), and 0.1 ng/cm(2) for diethanolamine (DEA).

Array of Love-wave sensors based on quartz/Novolac to detect CWA simulants.

An array of Love-wave sensors based on quartz and Novolac has been developed to detect chemical warfare agents (CWAs). These weapons are a risk for human health due to their efficiency and high lethality; therefore an early and clear detection is of enormous importance for the people safety. Love-wave devices realized on quartz as piezoelectric substrate and Novolac as guiding layer have been used to make up an array of six sensors, which have been coated with specific polymers by spin coating. The CWAs are very dangerous and for safety reasons their well known simulants have been used: dimethylmethyl phosphonate (DMMP), dipropyleneglycol methyl ether (DPGME), dimethylmethyl acetamide (DMA), dichloroethane (DCE), dichloromethane (DCM) and dichloropentane (DCP). The array has been exposed to these CWA simulants detecting very low concentrations, such as 25 ppb of DMMP, a simulant of nerve agent sarin. Finally, principal component analysis (PCA) as data pre-processing and discrimination technique, and probabilistic neural networks (PNN) as patterns classification technique have been applied. The performance of the sensor array has shown stability, accuracy, high sensitivity and good selectivity to these simulants.

Application of high performance liquid chromatography coupled to on-line solid-phase extraction-nuclear magnetic resonance spectroscopy for the analysis of degradation products of V-class nerve agents and nitrogen mustard.

The detection and identification of the degradation products of nitrogen mustard and nerve agent VX by high performance liquid chromatography coupled to on-line solid-phase extraction-nuclear magnetic resonance spectroscopy (HPLC-UV-SPE-NMR) were demonstrated. The analytes selected for the study were N,N-dimethylaminoethanol (DMAE), N,N-diethylaminoethanol (DEAE), N,N-diisopropylaminoethanol (DIAE) and triethanolamine (TEA). Offline solid-phase extraction (SPE) followed by derivatization was applied to eliminate the interferents and make the analytes amenable for UV detection. Thereafter, chromatographically separated derivatives were trapped on on-line SPE cartridges. They were subsequently eluted and 1H NMR and COSY spectra were obtained. The overall detection limits of the LC-UV-SPE-NMR method for the mentioned analytes were found to be 18, 23, 25, and 32 mg/L respectively. Applicability of the method to real samples was demonstrated by the analysis of samples provided during the 22nd OPCW official proficiency test. The method gave reproducible NMR spectra devoid of intense background signals.

Development of spray deposition/MALDI-TOFMS and its application to the rapid screening of hydrolysis products derived from nitrogen mustards.

A novel method for preparing samples for use in MALDI-TOFMS (matrix-assisted laser desorption ionization time-of-flight mass spectrometry) is described. Seven hydrolysis products derived from nitrogen mustards and CHCA (alpha-cyano-4-hydroxycinnamic acid) were selected as model compounds and the matrix, respectively. A capillary atomizer was used for evaporative and spray deposition of the sample/matrix solution, leading to the formation of a freestanding film that coated and accumulated on the MALDI substrate (i.e., sample plate). Compared to the traditional method for MALDI, which involves the production of dried droplets, the surface roughness was reduced, resulting in the accumulation of the sample-doped matrix on the sample plate. This resulted in an increase in the limit of detection of 1 - 2 orders of magnitude. In order to compare the structures of the sample-doped matrices obtained by the traditional dried droplet method versus the spray deposition method (developed in this study), the matrices were examined by SEM (scanning electron microscopy). The design of the capillary atomizer and details of the experimental conditions are reported. The application of this method to the above seven degradation products was successful, suggesting that it has great potential for use as a routine monitoring tool.

Modifications and insights into a method for the analysis of the nitrogen mustard mechlorethamine by high-performance liquid chromatography.

Previously, a method was presented for the analysis of mechlorethamine by derivatization of this unstable nitrogen mustard to bis(2-phenylthioethyl)methylamine (PTEMA), a stable compound suitable for analysis by HPLC with UV detection [J.C. Reepmeyer, J. Chromatogr. A, 1085 (2005) 262]. Mechlorethamine HCl served as a reference standard and it was derivatized in situ simultaneously with samples of mechlorethamine HCl in ointment preparations. This paper presents the synthesis of PTEMA on a gram scale, synthesis of its picrate salt, bis(2-phenylthioethyl)methylamine picrate (PTEMAP), and isolation of the picrate as a crystalline solid. PTEMAP may serve as a reference standard replacing the toxic mechlorethamine HCl. Insights into the handling, storage, drying, and hygroscopic properties of mechlorethamine HCl and PTEMAP are discussed. In addition, one step following the derivatization procedure in the original method is recognized as a potential for error, and a procedure relating to the order of addition of reagents is presented to avoid this error. The method has been extended to the analysis of mechlorethamine in aqueous solutions.

Development of a liquid chromatography-multiple reaction monitoring procedure for concurrent verification of exposure to different forms of mustard agents.

A novel liquid chromatography-multiple reaction monitoring (LC-MRM) procedure has been developed for retrospective diagnosis of exposure to different forms of mustard agents. This concise method is able to validate prior exposure to nitrogen mustards (HN-1, HN-2, and HN-3) or sulfur mustard (HD) in a single run, which significantly reduces analysis time compared to separate runs to screen for different mustards' biomarkers based on tandem mass spectrometry. Belonging to one of the more toxic classes of chemical warfare agents, these potent vesicants bind covalently to the cysteine-34 residue of human serum albumin. This results in the formation of stable adducts whose identities were confirmed by a de novo sequencing bioinformatics software package. Our developed technique tracks these albumin-derived adduct biomarkers in blood samples which persist in vitro following exposure, enabling a detection limit of 200 nM of HN-1, 100 nM of HN-2, 200 nM of HN-3, or 50 nM of HD in human blood. The CWA-adducts formed in blood samples can be conveniently and sensitively analyzed by this MRM technique to allow rapid and reliable screening.

Determination of nitrogen mustard hydrolysis products, ethanolamines by gas chromatography-mass spectrometry after tert-butyldimethylsilyl derivatization.

A method for determining N-ethyldiethanolamine (EDEA), N-methyldiethanolamine (MDEA) and triethanolamine (TEA), hydrolysis products of nitrogen mustards, in water, urine and blood samples using gas chromatography-mass spectrometry (GC-MS) after derivatization by tert-butyldimethylsilylation (TBDMS) is described. The sample solution was evaporated to dryness, and reacted with N-methyl-N-(tert-butyldimethylsilyl)trifluoroacetamide (MTBSTFA) at 60 degrees C for 1h. The TBDMS derivatives were separated on a DB-5 column and detected by electron-ionization MS. The quantitation of EDEA, MDEA and TEA was performed by measuring the respective peak areas on the extracted ion chromatograms of m/z 216, m/z 202 and m/z 346, respectively, using nonadecane (C19), the peak area of which was measured at m/z 268, as an internal standard. When the water sample was initially analyzed, considerable loss of EDEA, MDEA and TEA occurred by evaporation. The addition of hydrochloric acid (HCl) to the water sample (final 1 mM), however, permitted quantitative recoveries to be achieved (88%, 88% and 79% for EDEA-(TBDMS)2, MDEA-(TBDMS)2 and TEA-(TBDMS)3, respectively). The limits of detections (LODs, scan mode, S/N = 3) were 2.5, 2.5 and 10 ng/ml for EDEA, MDEA and TEA, respectively. Ethanolamines could be also determined in urine samples (volume 0.1 ml), with reasonable recoveries of 72-100% by the addition of HCl (final 1 mM). For the analysis of serum samples, the sample was precipitated by the addition of perchloric acid (final 3.2%), and the resulting supernatant was neutralized with potassium carbonate, and then acidified by the addition of HCl. The recovery of TBDMS derivatives of ethanolamines was found to rather low (7-31%).

Screening of nitrogen mustards and their degradation products in water and decontamination solution by liquid chromatography-mass spectrometry.

Analysing nitrogen mustards and their degradation products in decontamination emulsions posed a significant challenge due to the different phases present in such matrices. Extensive sample preparation may be required to isolate target analytes. Furthermore, numerous reaction products are formed in the decontamination emulsion. A fast and effective qualitative screening procedure was developed for these compounds, using liquid chromatography-mass spectrometry (LC-MS). This eliminated the need for additional sample handling and derivatisation that are required for gas chromatographic-mass spectrometric (GC-MS) analysis. A liquid chromatograph with mixed mode column and isocratic elution gave good chromatography. The feasibility of applying this technique for detecting these compounds in spiked water and decontamination emulsion was demonstrated. Detailed characterisation of the degradation products in these two matrices was carried out. The results demonstrated that N-methyldiethanolamine (MDEA), N-ethyldiethanolamine (EDEA) and triethanolamine (TEA) are not the major degradation products of their respective nitrogen mustards. Degradation profiles of nitrogen mustards in water were also established. In verification analysis, it is important not only to develop methods for the identification of the actual chemical agents; the methods must also encompass degradation products of the chemical agents as well so as to exclude false negatives. This study demonstrated the increasingly pivotal role that LC-MS play in verification analysis.

Analysis of the nitrogen mustard mechlorethamine in topical pharmaceutical preparations by high-performance liquid chromatography.

Mechlorethamine in topical pharmaceutical formulations was derivatized with benzenethiol to form the disubstitution product and analyzed by normal-phase HPLC on silica gel using dibutyl phthalate as an internal standard. The derivatization reaction, purification, and isolation were conveniently performed in a single test tube. Analyses were successfully performed on three types of ointment formulations: anhydrous hydrophobic petrolatum-based ointments, anhydrous hydrophilic ointments, and hydrous hydrophilic ointments. Precision for the analysis of mechlorethamine standard or mechlorethamine in ointments ranged from 0.08 to 0.52% RSD (n = 6). Recoveries from ointments spiked with 0.02% mechlorethamine hydrochloride were 98.4-100.4%. The chromatograms were clean, showing minimal or no interference from ointment excipients or reagents.

On-matrix derivatisation-extraction of precursors of nitrogen- and sulfur-mustards for verification of chemical weapons convention.

Development and refinement of sample preparation protocols for retrospective detection and identification of chemical warfare agents (CWAs) and their markers is of paramount importance from verification point of view of chemical weapons convention (CWC). Precursors of nitrogen- and sulfur-mustards (NMPs and SMPs) are polar adsorptive markers of vesicant class of CWAs. Their detection in a given environmental sample may imply past contamination with mustards. For the efficient extraction of NMPs and SMPs from soil, on-matrix derivatisation-extraction (OMDEX) method was developed and optimized. The method involved trifluoroacetylation of analytes on soil itself, followed by extraction with suitable solvent. The extracted samples were analyzed by gas chromatography-mass spectrometry (GC-MS). This virtually single-step sample preparation offered better recoveries of NMPs and SMPs in comparison to conventionally used extraction, evaporation and derivatisation. The best recoveries of analytes were obtained with acetonitrile by OMDEX method. Dynamic linearity range of trifluoroacetylated (TFA) derivatives of NMPs and SMPs was 1-12 microg/L in GC-MS analysis in SIM mode. Repeatability and reproducibility of this technique containing 5 and 10 microg analytes/gm soil was <3.3% and <4.6%, respectively. OMDEX technique was finally applied for the detection of TFA derivatives of NMPs in the soil sample supplied in 16th official proficiency test conducted by OPCW in October 2004.