A bibliometric perspective on the occurrence and migration of microplastics in soils amended with sewage sludge.

The land application of sewage sludge from wastewater treatment plants has been recognized as a major source of microplastic contamination in soil. Nevertheless, the fate and behavior of microplastics in soil remain uncertain, particularly their distribution and transport, which are poorly understood. This study does a bibliometric analysis and visualization of relevant research publications using the CiteSpace software. It explores the limited research available on the topic, highlighting the potential for it to emerge as a research hotspot in the future. Chinese researchers and institutions are paying great attention to this field and are promoting close academic cooperation among international organizations. Current research hot topics mainly involve microplastic pollution caused by the land application of sewage sludge, as well as the detection, environmental fate, and removal of microplastics in soil. The presence of microplastics in sludge, typically ranging from tens of thousands to hundreds of thousands of particles (p)/kg, inevitably leads to their introduction into soil upon land application. In China, the estimated annual accumulation of microplastics in the soil due to sludge use is approximately 1.7 × 1013 p. In European countries, the accumulation ranges from 8.6 to 71 × 1013 p. Sludge application has significantly elevated soil microplastic concentrations, with higher application rates and frequencies resulting in up to several-fold increases. The primary forms of microplastics found in soils treated with sludge are fragments and fibers, primarily in white color. These microplastics consist primarily of components such as polyamide, polyethylene, and polypropylene. The vertical transport behavior of microplastics is influenced by factors such as tillage, wind, rainfall, bioturbation, microplastic characteristics (e.g., fraction, particle size, and shape), and soil physicochemical properties (e.g., organic matter, porosity, electrical conductivity, and pH). Research indicates that microplastics can penetrate up to 90 cm into the soil profile and persist for decades. Microplastics in sewage sludge-amended soils pose potential long-term threats to soil ecosystems and even human health. Future research should focus on expanding the theoretical understanding of microplastic behavior in these soils, enabling the development of comprehensive risk assessments and informed decision-making for sludge management practices. PRACTITIONER POINTS: Microplastics in sewage sludge range from tens to hundreds of thousands per kilogram. Sludge land application contributes significantly to soil microplastic pollution. The main forms of microplastics in sludge-amended soils are fragments and fibers. Microplastics are mainly composed of polyamide, polyethylene, and polypropylene. Microplastics can penetrate up to 90 cm into the soil profile and persist for decades.

Creation of an international laboratory network towards global microplastics monitoring harmonisation.

Infrastructure is often a limiting factor in microplastics research impacting the production of scientific outputs and monitoring data. International projects are therefore required to promote collaboration and development of national and regional scientific hubs. The Commonwealth Litter Programme and the Ocean Country Partnership Programme were developed to support Global South countries to take actions on plastics entering the oceans. An international laboratory network was developed to provide the infrastructure and in country capacity to conduct the collection and processing of microplastics in environmental samples. The laboratory network was also extended to include a network developed by the University of East Anglia, UK. All the laboratories were provided with similar equipment for the collection, processing and analysis of microplastics in environmental samples. Harmonised protocols and training were also provided in country during laboratory setup to ensure comparability of quality-controlled outputs between laboratories. Such large networks are needed to produce comparable baseline and monitoring assessments.

A systematic review on microplastic contamination in marine Crustacea and Mollusca of Asia: Current scenario, concentration, characterization, polymeric risk assessment, and future Prospectives.

Microplastics (MPs) pollution has wreaked havoc on biodiversity and food safety globally. The false ingestion of MPs causes harmful effects on organisms, resulting in a decline in biodiversity. The present review comprehended the current knowledge of MP contamination in Crustacea and Mollusca from 75 peer-reviewed articles published in Asia between 2015 and 2023. A total of 79 species (27 Crustacea and 52 Mollusca) have been recorded to be contaminated with MPs. Out of the total 27 species of Crustacea, Metopograpsus quadridentatus (327.56 MPs/individual) and Balanus albicostatus (0.42 MPs/individual) showed the highest and lowest contamination, respectively. Out of the total 52 species of Mollusca, Dolabella auricularia (2325 MPs/individual) and Crassostrea gigas and Mytilus edulis (0.2 MPs/individual) showed the highest and lowest contamination, respectively. In terms of country-wise MP contamination, China has the highest number of contaminated species in both phylums among Asia. Findings of pollution indices revealed a very high risk of MP contamination in all the countries. Fiber was reported predominantly in both groups. Blue and black-colored MPs having <500 µm and <500 µm-1 mm size were found dominantly in Crustacea and Mollusca, respectively. Polypropylene was recorded as the dominant plastic polymer in both Crustacea and Mollusca. In essence, this review has provided a comprehensive insight into MP concentration in Crustacea and Mollusca of Asia, highlighting variations among species and geographic locations. This understanding is crucial for tackling urgent environmental challenges, safeguarding human health, and promoting global sustainability initiatives amid the escalating issue of plastic pollution. PRACTITIONER POINTS: Microplastic pollution has created havoc on biodiversity and food safety. A total of 27 and 52 species of crustaceans and Mollusca have been recorded to be contaminated with MPs. Metopograpsus quadridentate and Dolabella auricularia have shown higher MPs contamination. Polypropylene was recorded as the dominant plastic polymer in both crustacean and Mollusca. Findings of pollution indices revealed a very high risk of MP contamination in all the countries.

Anthropogenic particle abundance and characteristics in seawater and intertidal sediments of the Tonkin Bay Coast (North Vietnam).

Microplastics (MPs, plastic items from 1 µm to 5 mm in size) are present in all environmental compartments. The evaluation of their concentration, fate, and spatial distribution is still a challenge for the scientific community. This concern is just debuting in developing countries, (i.e., Asia, South America, and Africa). This study deals with the MP contamination in the abiotic marine compartments of Northern Vietnam: seawater and intertidal sediments. Four sites located in the intertidal zone or near the coastline in Tonkin Bay, Vietnam were studied. A total of 16 samples (eight for each compartment) were collected in July 2020 (rainy season) and January 2021 (dry season). Anthropogenic particles (total observed fibers and fragments) were found at levels ranging from 3 to 303 particles/m3 in seawater and from 63 to 955 particles/kg dry weight in sediments. Most of these were fibers less than 300-µm long. Higher levels of seawater at the Nam Dinh site were found in the rainy season compared to the dry one. As the river flow was estimated six times higher during the rainy season than during the dry season, these results suggest the river discharge is a potential source of contamination for the coastal zone. The temporal variability was lower for the sediments than for the seawater, suggesting the long-term integration of the anthropogenic particles in this compartment. A small portion of sorted particles were analyzed by µFTIR (8.35%), and this sub-sample was only composed of fragments. Still, fragments were mostly composed of polypropylene (PP, 82%), polyethylene (PE, 9%), and polystyrene (PS, 9%). The fragment size was similar in the two studied compartments, but it was dependent on polymer types since PS fragments (140 ± 17 µm) were smaller than those made of PE (622 ± 123 µm) and PP (869 ± 905 µm). Future works should investigate the smallest fraction of MP (even nanoplastics) as well as find solutions in order to mitigate MP contamination in the marine environment.

Point-source tracking of microplastics in sewerage systems. Finding the culprit.

Prior microplastic (MP) research has focused more on the efficiency of removal techniques within wastewater treatment plants (WWTP), with comparatively less emphasis placed on identifying and understanding the sources of MPs. In this study, the presence of MP in wastewater from various sources and their associated WWTPs was investigated. Utilising focal plane array micro Fourier Transform Infrared spectroscopy (FPA-µFTIR), the chemical composition, size distribution, and mass of MPs were quantified. Notably, wastewater generated from an industrial laundry facility exhibited the highest MP concentration of 6900 counts L-1 or 716 µg L-1. Domestic sewage contained MP levels (1534 counts L-1; 158 µg L-1) similar to those at the WWTPs (1640 counts L-1; 114 µg L-1). Polyester was identified as a significant component in most of the sources, predominantly originating from the shedding of fibres during textile washing. Additionally, a post-processing software was employed to compare two methods for fibre identification: aspect ratio and elongation ratio. These findings underscore the potential environmental impact of domestic activities and laundry washing on wastewater MP content.

Microplastic in an apex predator: evidence from Barn owl (Tyto alba) pellets in two sites with different levels of anthropization.

Plastic pollution in terrestrial and freshwater environments and its accumulation along food chains has been poorly studied in birds. The Barn owl (Tyto alba) is an opportunistic and nocturnal apex predator feeding mostly on small mammals. In this note, we reported evidence of microplastics (MPs) contamination in Barn owl pellets collected, for the first time, in two sites with different levels of anthropization (low: natural landscape mosaic vs. high extensive croplands). The following polymers have been recorded: polyvinylchloride (PVC), polyethylene (PE), expanded polyester (EPS), polyethylene terephthalate (PET), polybutylene terephthalate (PBT), polyester (PL), viscose, and starch-based biopolymer. We found significant higher MPs frequency in the most anthropized site. Our results suggest that pellet' analysis may represent a cost-effective method for monitoring MP contamination along food chains in terrestrial ecosystems.

Sustainable struggling: decoding microplastic released from bioplastics-a critical review.

This comprehensive review delves into the complex issue of plastic pollution, focusing on the emergence of biodegradable plastics (BDPs) as a potential alternative to traditional plastics. While BDPs seem promising, recent findings reveal that a large number of BDPs do not fully degrade in certain natural conditions, and they often break down into microplastics (MPs) even faster than conventional plastics. Surprisingly, research suggests that biodegradable microplastics (BDMPs) could have more significant and long-lasting effects than petroleum-based MPs in certain environments. Thus, it is crucial to carefully assess the ecological consequences of BDPs before widely adopting them commercially. This review thoroughly examines the formation of MPs from prominent BDPs, their impacts on the environment, and adsorption capacities. Additionally, it explores how BDMPs affect different species, such as plants and animals within a particular ecosystem. Overall, these discussions highlight potential ecological threats posed by BDMPs and emphasize the need for further scientific investigation before considering BDPs as a perfect solution to plastic pollution.

Evidence of microplastics in the polychaete worm (capitellids-Capitella capitata) (Fabricicus, 1780) along Thoothukudi region.

Research on the occurrence of microplastics in invertebrates of the Thoothukudi region is limited. Capitellids are non-selective suspension feeders and are usually used as bioindicator of water pollution. Hence, an investigation was carried out to identify the microplastic occurrence in the capitellids (Capitella capitata) (Fabricius, 1780) collected from the Vellapatti and Spic Nagar sites of the Thoothukudi region. Result from this investigation showed the occurrence of 0.21 ± 0.17 items/indiv and a mean abundance of 13.33% in Thoothukudi coast. The mean microplastic abundance in the capitellids was significantly higher in the Spic Nagar (0.26 ± 0.19 MPs/indiv), probably due to the dumping of plastic waste, fishing and recreational activities. However, no significant difference was observed between seasons. Only fragments (Vellapatti 66.66% and Spic Nagar 33.33%) and fibre-shaped microplastics (Vellapatti 50% and Spic Nagar 50%) were identified. The size and colour of the microplastics dominant in both sites were 1-2 mm (Vellapatti 77.77% and Spic Nagar 75%) and blue (Vellapatti 88.88% and Spic Nagar 87.5%), respectively. The results of Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR) analysis revealed the presence of polyethylene (PE) and polypropylene (PP) polymers in the capitellids. PE polymer is one of the most common sources of microplastics contamination globally and it is also frequently found in the coastal waters of Thoothukudi. This accounted for the high occurrence of PE polymers in the capitellids with the occurrence rate of 77% in Vellapatti and 58.52% in Spic Nagar. The present study provides baseline data on the occurrence, characterization (shapes, sizes and colours) and qualitative analysis of the microplastics in the capitellids, and their presence was influenced by their non-selective feeding habits. Further, future studies have to be conducted to identify the levels of microplastics in different polychaetes and other invertebrates to better understand the effects of microplastic pollution in invertebrate communities.

The first reported values of microplastics in prostate.

BACKGROUND: Microplastics are ubiquitous, widespread environmental pollutants with unavoidable human exposure. Herein, it was aimed to investigate the presence of microplastics in prostate tissue. METHODS: Prostate tissues from 12 patients who underwent Trans Urethral Resection of the Prostate (TUR-P) were analyzed to investigate the presence of microplastics. Initially, the prostate tissues were analyzed for microplastic particles using a light microscope after extraction. Subsequently, the chemical composition of the particles found in the prostate tissues was characterized using Attenuated Total Reflection-Fourier Transform Infrared (ATR-FTIR) spectrophotometry. RESULTS: Microplastic particles of various types were detected in 6 out of 12 patients. All detected plastic particles in this study were microplastics, with sizes below 26 µm in size. These microplastics exhibited different shapes as pellets, spheres or fibers. Overall, among the 12 analyzed prostate tissue samples, four different types of plastic were identified in six samples. The most common type of microplastic detected was Polyamide (Nylon 6), found in samples from three patients. Other detected types, Polypropylene, Polyacrylic Acid and Poly (dimethylsiloxane) were each determined in samples from one patient. CONCLUSIONS: This is the first study to demonstrate the presence of microplastics in prostate tissue, serving as an exploratory investigation, which can trigger further research to validate the results in a larger patient cohort.

Microplastics and non-natural cellulosic particles in Spanish bottled drinking water.

This investigation explored the presence of microplastics (MPs) and artificial cellulosic particles (ACPs) in commercial water marketed in single use 1.5 L poly(ethylene terephthalate) bottles. In this work we determined a mass concentration of 1.61 (1.10-2.88) µg/L and 1.04 (0.43-1.82) µg/L for MPs and ACPs respectively in five top-selling brands from the Spanish bottled water market. Most MPs consisted of white and transparent polyester and polyethylene particles, while most ACPs were cellulosic fibers likely originating from textiles. The median size of MPs and ACPs was 93 µm (interquartile range 76-130 µm) and 77 µm (interquartile range 60-96 µm), respectively. Particle mass size distributions were fitted to a logistic function, enabling comparisons with other studies. The estimated daily intake of MPs due to the consumption of bottled water falls within the 4-18 ng kg-1 day-1 range, meaning that exposure to plastics through bottled water probably represents a negligible risk to human health. However, it's worth noting that the concentration of plastic found was much higher than that recorded for tap water, which supports the argument in favour of municipal drinking water.

Microplastic Pollution in High Population Density Zones of Selected Rivers from Southeast Asia.

Southeast Asia (SEA) faces significant environmental challenges due to rapid population growth and economic activity. Rivers in the region are major sources of plastic waste in oceans. Concerns about their contribution have grown, but knowledge of microplastics in the area is still limited. This article compares microplastic levels in sediment and water from urban zones of three major rivers in SEA: Chao Phraya River (Thailand), Saigon River (Vietnam), and Citarum River (Indonesia). The study reveals that in all three rivers, microplastics were found, with the highest concentrations in Chao Phraya's water (80 ± 60 items/m3) and Saigon's sediment (9167 ± 4559 items/kg). The variations in microplastic sizes and concentrations among these rivers may be attributed to environmental factors and the exposure duration of plastic to the environment. Since these rivers are important water supply sources, rigorous land-use regulations and raising public awareness are crucial to mitigate plastic and microplastic pollution.

Terrestrial wildlife as indicators of microplastic pollution in western Thailand.

Plastic pollution in terrestrial wildlife represents a new conservation challenge, with research in this area, especially within protected areas (PAs), being scant. This study documents the accumulation of microplastics (MPs) in terrestrial wildlife both inside and outside PAs in western Thailand. Carcasses of road-killed vertebrates in good condition, as well as live tadpoles, were collected to examine their exposure to plastic pollution. The digestive tracts of the vertebrate carcasses and the entire bodies of tadpoles were analyzed for MPs, which were identified if they measured over 50 µm. A total of 136 individuals from 48 vertebrate species were examined. The sample comprised snakes (44.12%), birds (11.03%), lizards (5.15%), tadpoles (32.25%), amphibians (5.88%), and mammals (1.47%). In total, 387 MPs were found in 44 species (91.67%), with an average occurrence of 3.25 ± 3.63 MPs per individual or 0.05 ± 0.08 MPs per gram of body weight. The quantities of MPs significantly varied among the animal groups, both in terms of number per individual (p < 0.05) and number per gram of body weight (p < 0.01). Furthermore, a significant difference in MP quantities was observed between specimens collected inside and outside PAs on an individual basis (p < 0.05), but not on a body weight basis (p = 0.07). Most MPs were fibers (77%), followed by fragments (22.22%), with only a minimal presence of film (0.52%) and foam (0.26%). Of all the MPs identified, 36.84% were confirmed as plastics or fibers made from natural materials, and 31.58% were plastics, including Polyethylene (PE), polyethylene terephthalate (PET), polypropylene (PP), Polyvinylidene chloride (PVDC), and polyester (PES). Additionally, fibers made of cotton, and those containing polyurethane (PU), rayon, PES, and combinations of rayon and PU, were identified. The quantities of MPs were significantly influenced by animal body weight, factors associated with human settlement/activity, and land use types. Our findings highlight the prevalence of plastic pollution in terrestrial vertebrates within Thai PAs. Further toxicological studies are required to establish plastic pollution standards. It is proposed that snakes, obtained from road kills, could serve as a non-invasive method for monitoring plastic pollution, thus acting as an indicator of the pollution threat to species within terrestrial ecosystems. There is an urgent need for the standardization of solid waste management at garbage dump sites in remote areas, especially within PAs. Conservation education focusing on MP occurrence, potential sources, and impacts could enhance awareness, thereby influencing changes in behaviors and attitudes toward plastic waste management at the household level.

Microplastics in seafood: Consumer preferences and valuation for mitigation technologies.

Microplastics, an emerging pollutant, have garnered widespread attention due to potential repercussions on human health and the environment. Given the critical role of seafood in food security, growing concerns about microplastics might be detrimental to meeting future global food demand. This study employed a discrete choice experiment to investigate Chilean consumers' preferences for technology aimed at mitigating microplastic levels in mussels. Using a between-subjects design with information treatments, we examined the impact of informing consumers about potential human health and environmental effects linked to microplastics pollution on their valuation for the technology. We found that the information treatments increased consumers' willingness to pay for mussels. Specifically, consumers were willing to pay a premium of around US$ 4 for 250 g of mussel meat with a 90 % depuration efficiency certification. The provision of health impact information increased the price premium by 56 %, while the provision of environmental information increased it by 21 %. Furthermore, combined health and environmental information significantly increased the probability of non-purchasing behavior by 22.8 % and the risk perception of microplastics for human health by 5.8 %. These results emphasized the critical role of information in shaping consumer preferences and provided evidence for validating investment in research and development related to microplastic pollution mitigation measures.

Microplastic contamination in urban aquatic environments: Occurrence characteristics in urban streams and stormwater runoff from urban surfaces.

This study investigates microplastics in urban environments, focusing on their abundance, types, and relationships with hydrological parameters. Microplastic analyses encompassed two steps: (1) examining urban streams including discharges from a wastewater treatment plant (WWTP) during non-rainy seasons, and (2) analyzing stormwater runoff from urban surfaces for microplastic content during rainy seasons. In urban streams, WWTP discharge exhibited higher microplastic concentrations compared to other streams, indicating WWTP discharge is a dominant source of microplastic pollution. The most prevalent microplastics detected were polypropylene, polyethylene, and their copolymer, although a variety of other types were also found. Concentrations of microplastics were notably influenced by specific urban land uses, as evidenced by a strong correlation (0.95) between microplastic concentrations and areas characterized by industrial and transportation activities. During rainy seasons, microplastics followed the pattern of stormwater runoff, but the highest concentrations, significantly exceeding those in urban streams, were observed before the peak runoff. These maximum concentrations and their timing of occurrence were linked to antecedent dry days, rain intensity, and runoff rate, showing significant statistical correlations. Regardless of their sizes, a diverse range of microplastic types was identified in these conditions, with no consistent pattern across different rain events. This highlights the complex nature of urban microplastic pollution. This study reveals that aquatic ecosystems are significantly affected by two primary factors: (1) the consistent contribution of microplastics from WWTP discharges, and (2) the short-term, but severe, impacts of microplastic pollution associated with stormwater runoff. Furthermore, it suggests the development of alternative strategies to mitigate microplastic pollution in aquatic ecosystems, informed by the findings on the characteristics of microplastics in urban environments. This research underscores the urgent need for integrated urban environmental management strategies, paving the way for future studies to further explore and address the multifaceted challenges posed by microplastic pollution in aquatic ecosystems.

Nile red staining for rapid screening of plastic-suspect particles in edible seafood tissues.

Concerns regarding microplastic (MP) contamination in aquatic ecosystems and its impact on seafood require a better understanding of human dietary MP exposure including extensive monitoring. While conventional techniques for MP analysis like infrared or Raman microspectroscopy provide detailed particle information, they are limited by low sample throughput, particularly when dealing with high particle numbers in seafood due to matrix-related residues. Consequently, more rapid techniques need to be developed to meet the requirements of large-scale monitoring. This study focused on semi-automated fluorescence imaging analysis after Nile red staining for rapid MP screening in seafood. By implementing RGB-based fluorescence threshold values, the need for high operator expertise to prevent misclassification was addressed. Food-relevant MP was identified with over 95% probability and differentiated from natural polymers with a 1% error rate. Comparison with laser direct infrared imaging (LDIR), a state-of-the-art method for rapid MP analysis, showed similar particle counts, indicating plausible results. However, highly variable recovery rates attributed to inhomogeneous particle spiking experiments highlight the need for future development of certified reference material including sample preparation. The proposed method demonstrated suitability of high throughput analysis for seafood samples, requiring 0.02-0.06 h/cm2 filter surface compared to 4.5-14.7 h/cm with LDIR analysis. Overall, the method holds promise as a screening tool for more accurate yet resource-intensive MP analysis methods such as spectroscopic or thermoanalytical techniques.

The deciphering of microplastics-derived fluorescent dissolved organic matter in urban lakes, canals, and rivers using parallel factor analysis modeling and mimic experiment.

The aim of the study is to investigate the leaching of fluorescent dissolved organic matter (fDOM) from microplastics. In addition, this study identifies the connection between fDOM and microplastics in the aquatic environment. Three-dimensional excitation-emission matrix identified five fluorophores, that is, peak A, M, T, Tuv, and Wuv, and the parallel factor analysis modeling identified five components, that is, tryptophan-like, p-hydroxy acetophenone, humic acid (C-like), detergent-like, and fulvic acid (M-like) in the urban surface water. Mimic experiments using commonly used synthetic plastic (like microplastics) in Mili-Q water under solar radiation and dark environments demonstrate the release of fDOM from plastic. Two fluorophore peaks were observed at Ex/Em = 250/302 nm and Ex/Em = 260/333 nm for the expanded polystyrene plastic polymer and one fluorophore peak at Ex/Em = 260/333 nm for the low-density polyethylene. Fluorophore and component intensity exhibited notable associations with microplastics in the aquatic environment. These findings indicated that the characteristics and dynamics of fDOM in urban surface water are influenced by microplastics. PRACTITIONER POINTS: Fluorescent dissolved organic matters were identified in urban surface waters. Expanded polystyrene (EPS) had shown two fluorophores at Em/Ex = 250/302 and Em/Ex = 260/333. Low-density polyethylene (LDPE) had one fluorophore at Em/Ex = 260/333. Fluorophore and component intensity in the aquatic settings exhibited associations with microplastics.

Altitudinal variation of microplastic abundance in lakeshore sediments from Italian lakes.

Microplastic (MP) contamination represents an issue of global concern for both aquatic and terrestrial ecosystems, but only in recent years, the study of MPs has been focused on freshwaters. Several monitoring surveys have detected the presence of a wide array of MPs differing in size, shape, and polymer composition in rivers and lakes worldwide. Because of their role of sink for plastic particles, the abundance of MPs was investigated in waters, and deep and shoreline sediments from diverse lakes, confirming the ubiquity of this contamination. Although diverse factors, including those concerning anthropogenic activities and physical characteristics of lakes, have been supposed to affect MP abundances, very few studies have directly addressed these links. Thus, the aim of the present study was to explore the levels of MP contamination in mountain and subalpine lakes from Northern Italy. Fourteen lakes dislocated at different altitudes and characterized by dissimilar anthropic pressures were visited. Lakeshore sediments were collected close to the drift line to assess MPs contamination. Our results showed the presence of MPs in lakeshore sediments from all the lakes, with a mean (± standard deviation) expressed as MPs/Kg dry sediment accounting to 14.42 ± 13.31 (range 1.57-61.53), while expressed as MPs/m2, it was 176.07 ± 172.83 (range 25.00-666.67). The MP abundance measured for Garda Lake was significantly higher compared to all the other ones (F1,13 = 7.344; P < 0.001). The pattern of contamination was dominated by fibers in all the lakes, but they were the main contributors in mountain lakes. These findings showed that the MP abundance varied according to the altitude of the lakes, with higher levels measured in subalpine lakes located at low altitudes and surrounded by populated areas.