Neutron kerma factors and water equivalence of some tissue substitutes.

The Kerma factors and Kerma relative to the air and water of 24 compounds that are used as tissue substitutes were calculated for neutron energies ranging from 2.53×10(-8) to 29 MeV. The Kerma ratios of the tissue substitutes relative to air and water were calculated. The water equivalence of the selected tissue substitutes was observed above neutron energies of 100 eV. The Kerma ratio relative to the air for poly-vinylidene fluoride and Teflon were nearest to unity at very low energy (up to 1 eV) and above 63 eV, respectively. It was found that the natural rubber was a water-equivalent tissue substitute compound. The results of the Kerma factors in our investigation show good agreement with those published in ICRU-44. We found that at higher neutron energies, the Kerma factors and Kerma ratios of the selected tissue substitute compounds were approximately the same, but though the differences were large for energies below 100 eV.

New green polymeric composites based on hemp and natural rubber processed by electron beam irradiation.

A new polymeric composite based on natural rubber reinforced with hemp has been processed by electron beam irradiation and characterized by several methods. The mechanical characteristics: gel fraction, crosslink density, water uptake, swelling parameters, and FTIR of natural rubber/hemp fiber composites have been investigated as a function of the hemp content and absorbed dose. Physical and mechanical properties present a significant improvement as a result of adding hemp fibres in blends. Our experiments showed that the hemp fibers have a reinforcing effect on natural rubber similar to mineral fillers (chalk, carbon black, silica). The crosslinking rates of samples, measured using the Flory-Rehner equation, increase as a result of the amount of hemp in blends and the electron beam irradiation dose increasing. The swelling parameters of samples significantly depend on the amount of hemp in blends, because the latter have hydrophilic characteristics.

Dielectric properties of EVA rubber composites at microwave frequencies theory, instrumentation and measurements.

This work describes and evaluates a technique for determining the dielectric properties of carbon-black filled Ethylene Vinyl Acetate (EVA) rubber and presents results on the studies of the effect of frequency on the permittivity and microwave conductivity using resonant cavity perturbation method. The measurements are performed with the aid of a Network Analyzer in X-band. The simplicity of this method lies in the fact that the dielectric properties can be obtained directly from the analytical formula without taking recourse to calibration.

Radiation crosslinking of a bacterial medium-chain-length poly(hydroxyalkanoate) elastomer from tallow.

Pseudomonas resinovorans produces a medium-chain-length poly(hydroxyalkanoate) (MCL-PHA) copolymer when grown on tallow (PHA-tal). This polymer had a repeat unit composition ranging from C4 to C14 with some mono-unsaturation in the C12 and C14 alkyl side chains. Thermal analysis indicated that the polymer was semi-crystalline with a melting temperature (T(m)) of 43.5 +/- 0.2 degrees C and a glass transition temperature (Tg) of -43.4 +/- 2.0 degrees C. The presence of unsaturated side chains allowed crosslinking by gamma-irradiation. Irradiated polymer films had decreased solubility in organic solvents that indicated an increase in the crosslinking density within the film matrix. The addition of linseed oil to the gamma-irradiated film matrix enhanced polymer recovery while minimizing chain scission. Linseed oil also caused a decrease in the enthalpy of fusion (delta Hm) of the films (by an average of 60%) as well as enhanced mineralization. The effects of crosslinking on the mechanical properties and biodegradability of the polymer were determined. Radiation had no effect on the storage modulus (E') of the polymer. However, radiation doses of 25 and 50 kGy did increase the Young modulus of the polymer by 129 and 114%, and the tensile strength of the polymer by 76 and 35%, respectively. Finally, the formation of a higher crosslink density within the polymer matrix decreased the biodegradability of the PHA films.

Color changes in dry-pigmented maxillofacial elastomer resulting from ultraviolet light exposure.

Five dry pigments and one maxillofacial elastomer were evaluated for color changes (delta E) resulting from prolonged exposure to two types of ultraviolet light. The elastomer, pigments, and pigmented elastomers were subjected to each ultraviolet light source for 400, 600, and 1800 hours, and delta E color shifts were determined. The unpigmented elastomer underwent minimally perceptible color change after 600 hours of exposure to both types of ultraviolet light. Two pigments underwent substantial color change after 400 hours, whereas the remaining three pigments remained color stable after 1800 hours. It was concluded that for the materials tested, early color changes in a prosthesis may be the result of degradation of certain ultraviolet light-susceptible pigments, whereas longer term color shifts may be caused by color changes within the elastomer.

Reduction of antigenic protein levels in latex gloves after gamma irradiation.

Gamma irradiation is currently the method most commonly used to sterilize surgical gloves. In this study, the effect of gamma irradiation on antigenic proteins in latex gloves was examined. Protein extraction and quantitation were carried out using latex gloves before and after sterilization. Antigenic protein levels were determined by an ELISA assay specific for latex proteins (LEAP). LEAP analysis revealed a significant decrease after gamma-irradiation sterilization. This observation may partially explain the lower levels of extractable antigenic proteins found in sterile surgical gloves compared with nonsterile examination gloves. However, gamma irradiation was less effective than autoclave sterilization in reducing protein levels.