Outdoor manufacture of UV-Cured plastic linings for storm water culvert repair: Chemical emissions and residual.

Storm water culverts are integral for U.S. public safety and welfare, and their mechanical failure can cause roadways to collapse. To repair these buried assets, ultraviolet (UV) light cured-in-place-pipes (CIPP) are being installed. Chemical emission and residual material left behind from the installation process was investigated in New York and Virginia, USA. Samples of an uncured resin tube and field-cured styrene-based resin CIPPs were collected and analyzed. Also collected were air and water samples before, during, and after installations. Chemicals were emitted into air because of the installation and curing processes. Particulates emitted into the air, water, and soil contained fiberglass, polymer, and contaminants, some of which are regulated by state-level water quality standards. The uncured resin tube contained more than 70 chemical compounds, and 19 were confirmed with analytical standards. Compounds included known and suspected carcinogens, endocrine disrupting compounds, hazardous air pollutants, and other compounds with little aquatic toxicity data available. Compounds (14 of 19 confirmed) were extracted from the newly installed CIPPs, and 11 were found in water samples. Aqueous styrene (2.31 mg/L), dibutyl phthalate (12.5 µg/L), and phenol (16.7 µg/L) levels exceeded the most stringent state water quality standards chosen in this study. Styrene was the only compound that was found to have exceed a 48 h aquatic toxicity threshold. Newly installed CIPPs contained a significant amount volatile material (1.0 to > 9.0 wt%). Recommendations provided can reduce chemical emission, as well as improve worksite and environmental protection practices. Recommended future research is also described.

Mechanisms and Characterization of the Pulsed Electron-Induced Grafting of Styrene onto Poly(tetrafluoroethylene-co-hexafluoropropylene) to Prepare a Polymer Electrolyte Membrane.

During the pulsed-electron beam direct grafting of neat styrene onto poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP) substrate, the radiolytically-produced styryl and carbon-centered FEP radicals undergo various desired and undesired competing reactions. In this study, a high-dose rate is used to impede the undesired free radical homopolymerization of styrene and ensure uniform covalent grafting through 125-µm FEP films. This outweighs the enhancement of the undesired crosslinking reactions of carbon-centered FEP radicals and the dimerization of the styryl radicals. The degree of uniform grafting through 125-µm FEP films increases from ≈8%, immediately after pulsed electron irradiation to 33% with the subsequent thermal treatment exceeding the glass transition temperature of FEP of 39°C. On the contrary, steady-state radiolysis using 60Co gamma radiolysis, shows that the undesired homopolymerization of the styrene has become the predominant reaction with a negligible degree of grafting. Time-resolved fast kinetic measurements on pulsed neat styrene show that the styryl radicals undergo fast decays via propagation homopolymerization and termination reactions at an observed reaction rate constant of 5 × 108 l · mol-1 · s-1. The proton conductivity of 25-µm film at 80°C is 0.29 ± 0.01 s cm-1 and 0.007 s cm-1 at relative humidity of 92% and 28%, respectively. The aims of this work are: 1. electrolyte membranes are prepared via grafting initiated by a pulsed electron beam; 2. postirradiation heat-treated membranes are uniformly grafted, ideal for industry; 3. High dose rate is the primary parameter to promote the desired reactions; 4. measurement of kinetics of undesired radiation-induced styrene homopolymerization; and 5. The conductivity of prepared membranes is on par or higher than industry standards.

Ultrasonic degradation of butadiene, styrene and their copolymers.

Ultrasonic degradation of commercially important polymers, styrene-butadiene (SBR) rubber, acrylonitrile-butadiene (NBR) rubber, styrene-acrylonitrile (SAN), polybutadiene rubber and polystyrene were investigated. The molecular weight distributions were measured using gel permeation chromatography (GPC). A model based on continuous distribution kinetics approach was used to study the time evolution of molecular weight distribution for these polymers during degradation. The effect of solvent properties and ultrasound intensity on the degradation of SBR rubber was investigated using different pure solvents and mixed solvents of varying volatility and different ultrasonic intensities.

Effect of gamma-irradiation on some chemical characteristics and volatile content of linseed.

The effect of irradiation (2.5, 4.0, 5.5, and 7.0 kGy) on chemical properties and volatile contents of linseed was investigated. Consistent decreases were observed in both protein and oil content of the irradiated linseed samples with increasing irradiation doses. The ash content of the irradiated linseed samples increased significantly (P<.05) with increasing irradiation doses except for 5.5 kGy. Irradiation treatment caused irregular changes in palmitic and stearic acid content. Although styrene and p-xylene content decreased as a result of irradiation, 1-hexanol content only decreased at 7.0 kGy. Benzaldehyde, p-cymene, and nonanol were not determined at irradiation doses above 4.0 kGy.

Ultrafast dynamics through conical intersections and intramolecular vibrational energy redistribution in styrene.

We report a femtosecond time-resolved photoelectron spectroscopy (TRPES) investigation of internal conversion in the first two excited singlet electronic states of styrene. We find that radiationless decay through an S(1)/S(0) conical intersection occurs on a timescale of ∼4 ps following direct excitation to S(1) with 0.6 eV excess energy, but that the same process is significantly slower (∼20 ps) if it follows internal conversion from S(2) to S(1) after excitation to S(2) with 0.3 eV excess energy (0.9 eV excess energy in S(1)).

Highly thermostable anatase titania-pillared clay for the photocatalytic degradation of airborne styrene.

Airborne styrene is a suspected human carcinogen, and traditional ways of mitigation include the use of adsorption technologies (activated carbon or zeolites) or thermal destruction. These methods presenttheir own shortcomings, i.e., adsorbents need to be regenerated or replaced regularly, and relatively large energy inputs are required in thermal treatment. Photocatalysis offers a potentially sustainable and clean means of controlling such fugitive emissions of styrene in air. The present study demonstrates a new type of well-characterized, highly thermostable titania-pillared clay photocatalysts for airborne styrene decomposition in a custom-designed fluidized-bed photoreactor. This photocatalytic system is found to be capable of destroying up to 87% of 300 ppmV airborne styrene in the presence of ultraviolet (UV) irradiation. The effects of relative humidity (RH: 0 or 20%) are also studied, together with the arising physical structures (in terms of porosity and surface characteristics) of the catalysts when subjected to relatively high calcination temperatures of 1000-1200 degrees C. Such a temperature range may be encountered, e.g., in flue gas emissions (1). It is found that relative humidity levels of 20% retard the degradation efficiencies of airborne styrene when using highly porous catalysts.

Photoreductive degradation of sulfur hexafluoride in the presence of styrene.

Sulfur hexafluoride (SF6) is known as one of the most powerful greenhouse gases in the atmosphere. Reductive photodegradation of SF6 by styrene has been studied with the purpose of developing a novel remediation for sulfur hexafluoride pollution. Effects of reaction conditions on the destruction and removal efficiency (DRE) of SF6 are examined in this study. Both initial styrene-to-SF6 ratio and initial oxygen concentration exert a significant influence on DRE. SF6 removal efficiency reaches a maximum value at the initial styrene-to-SF6 ratio of 0.2. It is found that DRE increases with oxygen concentration over the range of 0 to 0.09 mol/m3 and then decreases with increasing oxygen concentration. When water vapor is fed into the gas mixture, DRE is slightly enhanced over the whole studied time scale. The X-ray Photoelectron Spectroscopy (XPS) analysis, together with gas chromatography-mass spectrometry (GC-MS) and Fourier Transform Infrared spectroscopy (FT-IR) analysis, prove that nearly all the initial fluorine residing in the gas phase is in the form of SiF4, whereas, the initial sulfur is deposited in the form of elemental sulfur, after photodegradation. Free from toxic byproducts, photodegradation in the presence of styrene may serve as a promising technique for SF6 abatement.