Methods for degrading dicloxacillin in water using inorganic peroxides and their combination with UVC- experimental and theoretical aspects.

Antibiotics are currently recognized as environmental pollutants. In this work, the methods involved in the degradation of a ß-lactam antibiotic (i.e., DXC) by treatments based on inorganic peroxides and UVC (e.g., UVC alone, UV-C/H2O2, UVC/peroxymonosulfate, and UVC/peroxydisulfate) are presented. The methodology of computational calculations to obtain frontier orbitals and Fukui indices for DXC, and elucidate the reactive moieties on the target substance is also shown. Finally, the direct oxidation by peroxides and UV-C/H2O2 action to treat DXC in simulated pharmaceutical wastewater are depicted. The chromatographic and theoretical analyses allowed for determining the degrading performance of inorganic peroxides and UVC-based treatments toward the target pollutant in aqueous samples.•Treatments based on inorganic peroxides and UVC as useful methods for degrading the ß-lactam antibiotic dicloxacillin.•Persulfates and UV-C/H2O2 showed high degrading action on the target pharmaceutical.•Methodologies based on theoretical calculations for the identification of reactive moieties on the DXC susceptible to radical attacks are presented.

Modulation of Electronic Availability in g-C3N4 Using Nickel (II), Manganese (II), and Copper (II) to Enhance the Disinfection and Photocatalytic Properties.

Carbon nitrides can form coordination compounds or metallic oxides in the presence of transition metals, depending on the reaction conditions. By adjusting the pH to basic levels for mild synthesis with metals, composites like g-C3N4-M(OH)x (where M represents metals) were obtained for nickel (II) and manganese (II), while copper (II) yielded coordination compounds such as Cu-g-C3N4. These materials underwent spectroscopic and electrochemical characterization, revealing their photocatalytic potential to generate superoxide anion radicals-a feature consistent across all metals. Notably, the copper coordination compound also produced significant hydroxyl radicals. Leveraging this catalytic advantage, with band gap energy in the visible region, all compounds were activated to disinfect E. coli bacteria, achieving total disinfection with Cu-g-C3N4. The textural properties influence the catalytic performance, with copper's stabilization as a coordination compound enabling more efficient activity compared to the other metals. Additionally, the determination of radicals generated under light in the presence of dicloxacillin supported the proposed mechanism and highlighted the potential for degrading organic molecules with this new material, alongside its disinfectant properties.

Intensifying the sonochemical degradation of hydrophilic organic contaminants by organic and inorganic additives.

The sonochemical system is highly effective at degrading hydrophobic substances but has limitations when it comes to eliminating hydrophilic compounds. This study examines the impact of organic and inorganic additives on improving the sonochemical degradation of hydrophilic pollutants in water. The effects of adding an organic substance (CCl4) and two inorganic ions (Fe2+ and HCO3-) were tested. The treatment was focused on a representative hydrophilic antibiotic, cefadroxil (CDX). Initially, the sonodegradation of CDX without additives was assessed and compared with two reference pollutants more hydrophobic than CDX: dicloxacillin (DCX) and methyl orange (MO). The results highlighted the limitations of ultrasound alone in degrading CDX. Subsequently, the impact of the additives on enhancing the removal of this recalcitrant pollutant was evaluated at two frequencies (375 and 990 kHz). A significant improvement in the CDX degradation was observed with the presence of CCl4 and Fe2+ at both frequencies. Increasing CCl4 concentration led to greater CDX elimination, whereas a high Fe2+ concentration had detrimental effects. To identify the reactive sites on CDX towards the species generated with the additives, theoretical calculations (i.e. Fukui indices and HOMO-LUMO gaps) were performed. These analyses indicated that the ß-lactam and dihydrothiazine rings on CDX are highly reactive towards oxidizing species. This research enhances our understanding of the relationship between the structural characteristics of contaminants and the sonochemical frequency in the action of additives having diverse nature.

Laser Ablation for the Synthesis of Cu/Cu2O/CuO and Its Development as Photocatalytic Material for Escherichia coli Detoxification.

Advanced Oxidation Processes (AOPs) offer promising methods for disinfection by generating radical species like hydroxyl radicals, superoxide anion radicals, and hydroxy peroxyl, which can induce oxidative stress and deactivate bacterial cells. Photocatalysis, a subset of AOPs, activates a semiconductor using specific electromagnetic wavelengths. A novel material, Cu/Cu2O/CuO nanoparticles (NPs), was synthesized via a laser ablation protocol (using a 1064 nm wavelength laser with water as a solvent, with energy ranges of 25, 50, and 80 mJ for 10 min). The target was sintered from 100 °C to 800 °C at rates of 1.6, 1.1, and 1 °C/min. The composite phases of Cu, CuO, and Cu2O showed enhanced photocatalytic activity under visible-light excitation at 368 nm. The size of Cu/Cu2O/CuO NPs facilitates penetration into microorganisms, thereby improving the disinfection effect. This study contributes to synthesizing mixed copper oxides and exploring their activation as photocatalysts for cleaner surfaces. The electronic and electrochemical properties have potential applications in other fields, such as capacitor materials. The laser ablation method allowed for modification of the band gap absorption and enhancement of the catalytic properties in Cu/Cu2O/CuO NPs compared to precursors. The disinfection of E. coli with Cu/Cu2O/CuO systems serves as a case study demonstrating the methodology's versatility for various applications, including disinfection against different microorganisms, both Gram-positive and Gram-negative.

Enantioselective Biomimetic Structures Inspired by Oxi-Dase-Type Metalloenzymes, Utilizing Polynuclear Compounds Containing Copper (II) and Manganese (II) Ions as Building Blocks.

This study focuses on developing and evaluating two novel enantioselective biomimetic models for the active centers of oxidases (ascorbate oxidase and catalase). These models aim to serve as alternatives to enzymes, which often have limited action and a delicate nature. For the ascorbate oxidase (AO) model (compound 1), two enantiomers, S,S(+)cpse and R,R(-)cpse, were combined in a crystalline structure, resulting in a racemic compound. The analysis of their magnetic properties and electrochemical behavior revealed electronic transfer between six metal centers. Compound 1 effectively catalyzed the oxidation of ascorbic to dehydroascorbic acid, showing a 45.5% yield for the racemic form. This was notably higher than the enantiopure compounds synthesized previously and tested in the current report, which exhibited yields of 32% and 28% for the S,S(+)cpse and R,R(-)cpse enantiomers, respectively. This outcome highlights the influence of electronic interactions between metal ions in the racemic compound compared to pure enantiomers. On the other hand, for the catalase model (compound 2), both the compound and its enantiomer displayed polymeric properties and dimeric behavior in the solid and solution states, respectively. Compound 2 proved to be effective in catalyzing the oxidation of hydrogen peroxide to oxygen with a yield of 64.7%. In contrast, its enantiomer (with R,R(-)cpse) achieved only a 27% yield. This further validates the functional nature of the prepared biomimetic models for oxidases. This research underscores the importance of understanding and designing biomimetic models of metalloenzyme active centers for both biological and industrial applications. These models show promising potential as viable alternatives to natural enzymes in various processes.

Manganese Dioxide Nanoparticles Prepared by Laser Ablation as Materials with Interesting Electronic, Electrochemical, and Disinfecting Properties in Both Colloidal Suspensions and Deposited on Fluorine-Doped Tin Oxide.

Nanoparticles (NPs) of α-MnO2 have high applicability in photoelectrochemical, heterogeneous photocatalysis, optical switching, and disinfection processes. To widen this panorama about MnO2 NPs, the formation of this material by laser ablation and deposition by dip-coating on fluorine-doped tin oxide (FTO), were considered in this study. The optical, spectroscopic, electrochemical characterization, and the evaluation of the antimicrobial activity, plus the photocatalytic response, were measured herein in colloidal media and deposited. For the deposition of NPs on FTO sheet, an anode is produced with a pseudocapacitive behavior, and 2.82 eV of band gap (GAP) in comparison with colloidal NPs for a value of 3.84 eV. Both colloidal suspension and deposited NPs have intrinsic antibacterial activity against two representative microorganisms (E. coli and S. aureus), and this biological activity was significantly enhanced in the presence of UVA light, indicating photocatalytic activity of the material. Thus, both the colloidal suspension and deposited NPs can act as disinfecting agents themselves or via light activation. However, an antibacterial behavior different for E. coli and S. aureus was observed, in function of the aggregation state, obtaining total E. coli disinfection at 30 min for deposited samples on FTO.

Treatment of two sartan antihypertensives in water by photo-electro-Fenton using BDD anodes: Degradation kinetics, theoretical analyses, primary transformations and matrix effects.

Degradation of two representative antihypertensives, losartan (LOS) and valsartan (VAL) in water by photo-electro-Fenton (PEF), using a BDD anode in presence of sulfate anion was evaluated. PEF showed a fast elimination of these pollutants (>95% at 30 and 60 min of treatment for LOS and VAL, respectively). The main elimination route was the attacks of radicals produced in the system, having pseudo-first-order rate constants of 0.154 and 0.054 min-1 for LOS and VAL, correspondingly. Theoretical analyses of atomic charges were performed to rationalize the antihypertensives reactivity toward the electrogenerated degrading agents. Afterwards, the primary transformation products were assessed. The transformation products revealed that the degrading species attack the biphenyl-tetrazole, imidazole, and alcohol moieties on LOS. Meanwhile, carboxylic and amide groups, plus the central nucleus, were modified on VAL. These moieties corresponded well with the electron-rich sites indicated by the theoretical calculations. Also, the PEF process removed between 33 and 38% of total organic carbon after 5 h of electrolysis. Finally, it was considered LOS treatment in presence of oxalic acid (a typical organic waste of pharmaceutical industry), in addition to the pollutant degradation in effluents from municipal sewage treatment plants by PEF at pH ∼5. Oxalic acid accelerated LOS degradation. Meanwhile, in the effluent, the process led to 64% of LOS removal after 120 min of treatment, indicating the high potentiality of PEF to degrade antihypertensives in water containing organic and inorganic substances.

Dataset on the degradation of losartan by TiO2-photocatalysis and UVC/persulfate processes.

Losartan is a highly consumed antihypertensive worldwide and commonly found in effluents of municipal wastewater treatment plants. In the environment, losartan can promote harmful effects on organisms. Thus, an option to face this pollutant is the treatment by photochemical advanced oxidation processes. This dataset has two main components: 1) theoretical calculations on reactivity indexes for losartan, and 2) degradation of the pollutant throughout TiO2-photocatalysis and UVC/persulfate (UVC/PS). The first part of the work presents the data about HOMO and LUMO energies, optimized geometry, dipolar moment, HOMO/LUMO energy gap and total density distribution, in addition to ionization energy, electron affinity, chemical potential, hardness, softness and electrophilicity for losartan. Meanwhile, the second one depicts information on the routes involved in the degradation of the pharmaceutical by the oxidation processes, mineralization, toxicity evolution and losartan removal from a complex matrix (synthetic fresh urine). The data reported herein may be utilized for further researches related to elimination of pharmaceuticals in primary pollution sources such as urine. Moreover, this work also provides experimental and theoretical data useful for the understanding of the response of losartan to oxidative and photochemical processes.

Data on treatment of nafcillin and ampicillin antibiotics in water by sonochemistry.

Ampicillin and nafcillin antibiotics were treated by high frequency ultrasound (at 375 kHz and 24.4 W). Degradations followed pseudo-first order kinetics, which constants were k: 0.0323 min-1 for AMP and k: 0.0550 min-1 for NAF. Accumulation of sonogenerated hydrogen peroxide and inhibition degree of sonochemical removal (IDS) in presence of a radical scavenger were also stablished. Afterwards, ultrasound was combined with UVC light (sono-photolysis), with ferrous ion (sono-Fenton), and with ferrous ion plus UVC light (sono-photo-Fenton) to degrade the antibiotics. Furthermore, treatment of the pollutants in a complex matrix and removal of antimicrobial activity (AA) were considered. The antibiotics evolution was followed by HPLC-DAD technique and the accumulation of sonogenerated H2O2 was measured by an iodometry-spectrophotometry methodology (77.6 and 57.3 µmol L-1 of H2O2 after 30 min of sonication were accumulated in presence of AMP and NAF, respectively). IDS was analyzed through treatment of the antibiotics in presence of 2-propanol (87.1% for AMP and 56 % for NAF) and considering the hydrophobic character of pollutants (i.e., Log P values). Antimicrobial activity evolution was assessed by the Kirby-Bauer method using Staphylococcus aureus as indicator microorganism (sono-photo-Fenton process removed 100% of AA after 60 and 20 min for AMP and NAF, respectively). Finally, for degradations in the complex matrix, a simulated effluent of municipal wastewater treatment plant was utilized (sono-photo-Fenton led to degradations higher than 90 % at 60 min of treatment for both antibiotics). The data from the present work can be valuable for people researching on treatment of wastewaters containing antibiotics, application of advanced oxidation technologies and combination of sonochemical process with photochemical systems.

Experimental data on synthesis and characterization of chiral dinuclear manganese (II-II) compounds as biomimetic models of the active center of catalase.

Dinuclear manganese (II- III) compounds, which are potential models of the active center of catalase, were synthetized. This type of metalloenzymes presents biological importance due to three factors: they are redox catalyst centres, they are able to carry out hydrolytic reactions and they participate in activated processes via Lewis acids. Structurally, their active centre is composed by dinuclear manganese compounds, linked to nitrogen and oxygen donor atoms. An octahedral geometry around the metal ions were found, with acetate, hydroxy and aquo ligands; which can work as molecule bridges between them. The acid medium favours the electronic transfer between Mn3+ - Mn2+ as redox centre at 1.559 V and the consequent oxidation of hydrogen peroxide or organic molecules. The work also reports the data of two chiral novel compounds, [Mn2(S,S(+)Hcpse)4(NaClO4)2(NaOH)(CH4O)]n·[(C2H6O)2]n·[(CH4O)2]n and its respective enantioisomer, in which µ-oxo being as bridge metal centre. The X-ray structural was obtained as well as the optical and magnetic properties using Circular Dichroism, Electronic Paramagnetic Resonance, Magnetic Susceptibility and X-ray photoelectron spectroscopy.

Rheological, Thermal, Superficial, and Morphological Properties of Thermoplastic Achira Starch Modified with Lactic Acid and Oleic Acid.

The modification of achira starch a thermoplastic biopolymer is shown. Glycerol and sorbitol, common plasticizers, were used in the molten state with organic acids such as oleic acid and lactic acid obtaining thermodynamically more stable products. The proportion of starch:plasticizer was 70:30, and the acid agent was added in portions from 3%, 6%, and 9% by weight. These mixtures were obtained in a torque rheometer for 10 min at 130 °C. The lactic acid managed to efficiently promote the gelatinization process by increasing the available polar sites towards the surface of the material; as a result, there were lower values in the contact angle, these results were corroborated with the analysis performed by differential scanning calorimetry and X-ray diffraction. The results derived from oscillatory rheological analysis had a viscous behavior in the thermoplastic starch samples and with the presence of acids; this behavior favors the transitions from viscous to elastic. The mixture of sorbitol or glycerol with lactic acid promoted lower values of the loss module, the storage module, and the complex viscosity, which means lower residual energy in the transition of the viscous state to the elastic state; this allows the compounds to be scaled to conventional polymer transformation processes.