Low-Cost Ni-W Catalysts Supported on Glucose/Carbon Nanotube Hybrid Carbons for Sustainable Ethylene Glycol Synthesis.

The production of ethylene glycol (EG) from cellulose has garnered significant attention in recent years as an attractive alternative to fossil fuels due to the potential of cellulose as a renewable and sustainable feedstock. In this work, to the best of our knowledge, a series of low-cost Ni-W bimetallic catalysts supported on glucose/carbon nanotube hybrid carbons were synthesised for the first time and employed to transform cellulose into EG. Two different strategies were combined for the preparation of the carbons: the activation and addition of carbon nanotubes (CNTs) to obtain a hybrid material (AG-CNT). The catalytic conversion process proceeded through cellulose hydrolysis to glucose, followed by glucose retro-aldol condensation to glycolaldehyde and its subsequent hydrogenation to EG. Through the optimisation of the catalyst's properties, particularly the metals' content, a good synergistic effect of C-C bond cleavage and hydrogenation capabilities was assured, resulting in the highly selective production of EG. The balance between Ni and W active sites was confirmed to be a crucial parameter. Thus, total cellulose conversion (100%) was achieved with EG yields of 60-62%, which are amongst the best yields ever reported for the catalytic conversion of cellulose into EG via carbon-supported catalysts.

Highly N2-Selective Activated Carbon-Supported Pt-In Catalysts for the Reduction of Nitrites in Water.

The catalytic reduction of nitrites over Pt-In catalysts supported on activated carbon has been studied in a semi-batch reactor, at room temperature and atmospheric pressure, and using hydrogen as the reducing agent. The influence of the indium content on the activity and selectivity was evaluated. Monometallic Pt catalysts are very active for nitrite reduction, but the addition of up to 1 wt% of indium significantly increases the nitrogen selectivity from 0 to 96%. The decrease in the accessible noble metal surface area reduces the amount of hydrogen available at the catalyst surface, this favoring the combination of nitrogen-containing intermediate molecules to promote the formation of N2 instead of being deeply hydrogenated into NH4+. Several activated carbon-supported Pt-In catalysts, activated under different calcination and reduction temperatures, have been also evaluated in nitrite reduction. The catalyst calcined and reduced at 400°C showed the best performance considering both the activity and the selectivity to nitrogen. This enhanced selectivity is ascribed to the formation of Pt-In alloy. The electronic properties of Pt change upon alloy formation, as it is demonstrated by XPS.

Catalytic and Photocatalytic Nitrate Reduction Over Pd-Cu Loaded Over Hybrid Materials of Multi-Walled Carbon Nanotubes and TiO2.

TiO2 and carbon nanotube-TiO2 hybrid materials synthesized by sol-gel and loaded with 1%Pd-1%Cu (%wt.) were tested in the catalytic and photocatalytic reduction of nitrate in water in the presence of CO2 (buffer) and H2 (reducing agent). Characterization of the catalysts was performed by UV-Vis and fluorescence spectroscopy, X-ray diffraction, temperature programed reduction, N2 adsorption, and electron microscopy. The presence of light produced a positive effect in the kinetics of nitrate removal. Higher selectivity toward nitrogen formation was observed under dark condition, while the photo-activated reactions showed higher selectivity for the production of ammonium. The hybrid catalyst containing 20 %wt. of carbon nanotubes shows the best compromise between activity and selectivity. A mechanism for the photocatalytic abatement of nitrate in water in the presence of the hybrid materials was proposed, based in the action of carbon nanotubes as light harvesters, dispersing media for TiO2 particles and as charge carrier facilitators.

CO oxidation over gold supported on Cs, Li and Ti-doped cryptomelane materials.

Cryptomelane-type manganese oxides were synthesized by redox reaction under acid and reflux conditions. Different metals (cesium, lithium and titanium) were incorporated into the tunnel structure by the ion-exchange technique. Gold was loaded onto these materials (1wt%) by a double impregnation method. The obtained catalysts were characterized by high-resolution transmission electron microscopy, energy-dispersive X-ray spectrometry, scanning electron microscopy, X-ray diffraction and temperature-programmed reduction. The catalytic activity of these materials was evaluated in the oxidation of carbon monoxide. The incorporation of Cs, Li or Ti into cryptomelane was detrimental in terms of catalytic activity. Further addition of gold to cryptomelane doped materials significantly improved the catalytic performance, especially for Cs-K-OMS-2 and Li-K-OMS-2 (to a smaller extent). Addition of gold to the Ti containing material did not show a significant improvement. The observed trends are related to the effect of gold on samples reducibility and to the gold particle size. The lattice oxygen can also be considered accountable for the activity of the materials, since the most active cryptomelane catalysts are those with higher lattice oxygen donating ability for the oxidation of the CO molecule.

Ozonation of bezafibrate over ceria and ceria supported on carbon materials.

Two catalysts containing ceria dispersed on the surface of multi-walled carbon nanotubes and activated carbon were investigated as ozonation catalysts for the mineralization of bezafibrate (BZF). The results were compared with those obtained in the absence of the catalyst and in the presence of the parent carbon materials, as well as in the presence of ceria (CeO2). Carbon materials containing ceria showed an interesting catalytic effect. Both materials enhanced the mineralization of BZF relatively to single ozonation and ozonation catalysed by the corresponding carbon materials. In the catalytic ozonation with these materials, both surface and bulk reactions are supposed to occur. The BZF ozonation catalysed by CeO2 leaded to the highest mineralization degrees, indicating that the reaction mechanism followed in the presence of CeO2 (free radical oxidation in solution) leads to the formation of intermediates more easily degradable, mainly after 120 min of reaction. Some primary products and refractory final oxidation compounds in single and catalytic ozonation of BZF were followed. The original chlorine present on the BZF molecule is completely converted to chloride anion and part of the nitrogen is mainly converted to NO3- along with smaller amounts of NO2- and NH4+. Microtox tests revealed that simultaneous use of ozone and CeO2 originated lower acute toxicity.

Catalytic ozonation of sulphamethoxazole in the presence of carbon materials: catalytic performance and reaction pathways.

Two carbon materials (multi-walled carbon nanotubes, MWCNTs, and activated carbon) were investigated as ozonation catalysts for the mineralization of the antibiotic sulphamethoxazole (SMX). MWCNTs presented a higher catalytic performance than activated carbons, which was justified by their differences in surface chemistry and by the higher internal mass transfer resistances expected for activated carbons. 3-Amino-5-methylisoxazole and p-benzoquinone were detected as primary products of single and catalytic ozonation of SMX, whereas oxamic, oxalic, pyruvic and maleic acids were identified as refractory final oxidation products. The original sulphur of the SMX was almost completely converted to sulphate and part of the nitrogen was converted to NH4+ and NO3-. The presence of the radical scavenger tert-butanol during catalytic and single ozonation evidenced the participation of HO radicals in the oxidation mechanisms of SMX, especially in the mineralization of several intermediates. Microtox tests revealed that simultaneous use of ozone and MWCNTs originated lower acute toxicity. The time course of all detected compounds was studied and the transformation pathway for the complete mineralization of SMX by single and catalytic ozonation in the presence of the selected materials was elucidated.

Effect of support and pre-treatment conditions on Pt-Sn catalysts: application to nitrate reduction in water.

The effect of the support (activated carbon or titanium dioxide) on the catalytic activity and selectivity to nitrogen of Pt-Sn catalysts in nitrate reduction was studied. The effects of the preparation conditions and the Pt:Sn atomic ratio were also evaluated. It was observed that the support plays an important role in nitrate reduction and that different preparation conditions lead to different catalytic activities and selectivities. Generally, the catalysts supported on activated carbon were less active but more selective to nitrogen than those supported on titanium dioxide. The monometallic Pt catalyst is active for nitrate reduction only when supported on titanium dioxide, which is explained by the involvement of the support in the reaction mechanism. The catalysts were characterized by different techniques, and significant changes on metal chemical states were observed for the different preparation conditions used. Only metallic Pt and oxidized Sn were observed at low calcination and reduction temperatures, but some metallic Sn was also present when high temperatures were used, being also possible the formation of Pt-Sn alloys.

Nitrate reduction over a Pd-Cu/MWCNT catalyst: application to a polluted groundwater.

The influence of the presence of inorganic and organic matter during the catalytic reduction of nitrate in a local groundwater over a Pd-Cu catalyst supported on carbon nanotubes was investigated. It was observed that the catalyst performance was affected by the groundwater composition. The nitrate conversion attained was higher in the experiment using only deionized water as solvent than in the case of simulated or real groundwater. With exception of sulphate ions, all the other solutes evaluated (chloride and phosphate ions and natural organic matter) had a negative influence on the catalytic activity and selectivity to nitrogen.

Production, characterization and application of activated carbon from brewer's spent grain lignin.

Different types of activated carbon were prepared by chemical activation of brewer's spent grain (BSG) lignin using H(3)PO(4) at various acid/lignin ratios (1, 2, or 3g/g) and carbonization temperatures (300, 450, or 600 degrees C), according to a 2(2) full-factorial design. The resulting materials were characterized with regard to their surface area, pore volume, and pore size distribution, and used for detoxification of BSG hemicellulosic hydrolysate (a mixture of sugars, phenolic compounds, metallic ions, among other compounds). BSG carbons presented BET surface areas between 33 and 692 m(2)/g, and micro- and mesopores with volumes between 0.058 and 0.453 cm(3)/g. The carbons showed high capacity for adsorption of metallic ions, mainly nickel, iron, chromium, and silicon. The concentration of phenolic compounds and color were also reduced by these sorbents. These results suggest that activated carbons with characteristics similar to those commercially found and high adsorption capacity can be produced from BSG lignin.

Ozonation of textile effluents and dye solutions under continuous operation: Influence of operating parameters.

Ozonation experiments were carried out under continuous operation in a bubble column. The effect of several parameters (inlet dye concentration, applied ozone dose, pH and conductivity) in colour and TOC removal of an acid dye solution was investigated with the aim to optimize the operation conditions. The ozone consumption was measured in each experiment. Ozonation was found to be effective for decolourisation of an acid dye; however, it only has a slight effect on TOC removal. Increasing the inlet dye concentration leads to a decrease in the decolourisation efficiency and an increase in the ozone consumption. The decolourisation increases with the applied ozone dose. Colour removal efficiencies for different ozone doses were between 76 and 100%. In the pH range 5-9, the decolourisation efficiency decreases with pH only when buffered solutions were used. The presence of salt decreases the decolourisation efficiency. Several dyes of different classes were also studied and ozonation was found to be effective for decolourisation but considerably less efficient for TOC removal. Under the conditions tested, only the disperse and sulphur dyes presented a colour removal lower than 86%. Practical application of this process was validated by treating two industrial textile effluents collected after two different biological treatments.

Adsorption of simple aromatic compounds on activated carbons.

The adsorption of model aromatic compounds (phenol, aniline, nitrobenzene) on modified activated carbons has been investigated. Electrostatic and dispersive adsorbate/adsorbent interactions are involved in this process. Their influence on the uptake of the above mentioned aromatic compounds has been evaluated using different solution pH conditions and activated carbon samples with different surface chemistries. These samples were obtained by modification of a commercial activated carbon by means of chemical treatment with HNO3 (acid sample) and thermal treatment under a flow of H2 (basic sample). The textural properties were not significantly changed after these modifications. The best uptake for all the adsorptives under most of the pH conditions used corresponded to the basic sample, which means that dispersive interactions are the most important in this process. However, electrostatic interactions cannot be neglected, as can be seen from the uptakes for the same sample at different pH. In the case of aniline at pH 2, electrostatic interactions are predominant, and the best uptake corresponds to the acid sample. The influence of textural properties on the adsorption process was also investigated, by comparing with another commercial activated carbon. As expected, for this type of organic compounds the uptake increases with the micropore surface area.

Mineralisation of coloured aqueous solutions by ozonation in the presence of activated carbon.

The degradation of organic matter in coloured solutions of different classes of dyes by ozonation in the presence of activated carbon is investigated. The kinetics of the decolourisation and mineralisation of three different dyes solutions (CI Acid Blue 113, CI Reactive Red 241 and CI Basic Red 14) were studied in a laboratory scale reactor by three different processes: adsorption on activated carbon, oxidation with ozone and ozonation in the presence of activated carbon. The mineralisation of the solutions was followed by measuring the total organic carbon (TOC). Under the experimental conditions used in this work, activated carbon was not capable of completely removing the colour of the solutions in reasonable time. On the other hand, ozonation quickly decolourised all the solutions, but satisfactory removal of TOC was never achieved by this process. The combination of activated carbon with ozone enhanced the decolourisation of the solutions and especially the mineralisation of the organic matter. Activated carbon acts both as an adsorbent and as a catalyst in the reaction of ozonation. The surface chemistry of the activated carbon is an important parameter; it was observed that basic samples improve TOC removal. The main conclusions of this work were validated by treating a real textile effluent collected after the conventional biological treatment.