Experimental investigation on solidification cracking & intergranular corrosion of AISI 321 & AISI 316 L dissimilar weld on pulsed current gas tungsten arc welding (PCGTAW).

Dissimilar metal combinations are frequently employed in the power generation and nuclear industries. Where stainless steel piping systems are connected to pressure vessels made of low-alloy steel, the subsystems of liquid rocket engines also have different, dissimilar material combinations. Dissimilar welding plays a vital role in ensuring the integrity, performance, and reliability of components and structures operating in cryogenic environments, in this study, plates of AISI 316L and AISI 321, each 5 mm thick, were successfully joined using the pulsed current gas tungsten arc welding (PCGTAW) technique with optimized process parameters. These weld joints are mostly present in rocket engines subjected to a cryogenic environment. Due to the low temperature environment, the metallurgical properties of these joints change, which affects their mechanical properties. As it is a structural part, PCGTAW welding is most common method for joining this kind of material. In this work, Microstructural analysis of the weldment revealed a combination of vermicular, lacy, and acicular ferrite morphologies in the fusion zone at the root, mid, and crown locations. Furthermore, no solidification cracking was detected in the weldments based on the optical micrograph and SEM results. Intergranular corrosion (IGC) testing indicated the absence of a ditch structure, suggesting that the heat-affected zone (HAZ) on both sides of the weld joint was not being susceptible to sensitization. However, the HAZ of the AISI 316L side exhibited coarser grains compared to AISI 321. Analysis of tensile properties revealed a significant influence of the testing environment on the tensile strength of the dissimilar welded joints. At room temperature, the average ultimate tensile strength (UTS) was measured as 621 MPa. Remarkably, at cryogenic conditions, the average tensile properties significantly increased to 1319 MPa. Microhardness analysis showed the highest hardness associated with the AISI 321 side. The fusion zone exhibited a large deviation in the hardness profile (205 ± 10 HV), with the highest average hardness observed in the middle part of the weld. However, the hot cracking behavior of the weld was investigated by using a suutula diagram at various locations of the weld. The investigation revealed that the Creq/Nieq ratio exceeded the critical threshold value, effectively diminishing the propensity for hot cracking in the fusion zone. Overall, these findings underscore the effectiveness of the PCGTAW technique in joining dissimilar materials, as well as the importance of microstructural and mechanical property evaluations, especially under extreme operating conditions such as cryogenic temperatures. Paraphrase.

Stiffness and stability of bamboo stem- A optimal design perspective.

During the evolution process, a bamboo stem achieves a significant height (up to 20 m) to fulfil its phototropic requirements. While on land, the stem is mostly subjected to bending load which makes it liable to fail by uprooting. However, this failure is prohibited by smart structure of bamboo stem which includes graded arrangement of fibre bundles in the cross-section and a tapered cantilever form of the stem. This paper attempts to understand the optimal design of bamboo stem through the relationship between the stellar arrangement of stiff fibre bundles in the cross-section and the tapered form. In this work, a comparison between two types of stellar arrangement, namely uniform and graded, is presented in view of non-linear bending analysis through elastica theory and fracture-induced delamination, both numerically. It is observed from the results that a bamboo stem prefers to evolve with graded stellar arrangement which provides gradation of stiffness and toughness over the cross-section; the trend in toughness being opposite to that of stiffness. Moreover, interplay of stellar arrangement and gradation of stiffness-toughness thereof is found to be the governing mechanism for ensuring its mechanical integrity and stability in view of an optimal design perspective. The smart structure of bamboo is recommended for bio-mimicking.

Tensile strength analysis of additively manufactured CM 247LC alloy specimen by employing machine learning classifiers.

Using a cutting-edge net-shape manufacturing technique called Additive Layer Manufacturing (ALM), highly complex components that are not achievable with conventional wrought and cast methods can be produced. As a result, the aerospace sector is paying closer attention to using this technology to fabricate superalloys based on nickel to develop the holistic gas turbine. Because of this, there is an increasing need for the mechanical characterisation of such material. Conventional mechanical testing is hampered by the limited availability of material that has been processed, especially given the large number of process factors that need to be assessed. Thus, the present study focuses on manufacturing CM247LC Ni-based superalloy with exceptional mechanical characteristics by laser powder bed fusion (L-PBF). This study evaluates the effect of input process variables such as laser power, scan speed, hatch distance and volumetric energy density on the mechanical performance of the LPBF CM247LC superalloy. The maximum value of as-built tensile strength obtained in the study is 997.81 MPa. Plotting Pearson's heatmap and the Feature importance (F-test) was used in the data analysis to examine the impact of input parameters on tensile strength. The accuracy of the tensile strength data classification by machine learning algorithms, such as k-nearest neighbours, Naïve Baiyes, Support vector machine, XGBoost, AdaBoost, Decision tree, Random forest, and logistic regression algorithms, was 92.5%, 83.75%, 83%, 85%, 87.5%, 90%, 91.25%, and 77.5%, respectively.

A Dynamic Traffic Light Control Algorithm to Mitigate Traffic Congestion in Metropolitan Areas.

This paper proposes a convolutional neural network (CNN) model of the signal distribution control algorithm (SDCA) to maximize the dynamic vehicular traffic signal flow for each junction phase. The aim of the proposed algorithm is to determine the reward value and new state. It deconstructs the routing components of the current multi-directional queuing system (MDQS) architecture to identify optimal policies for every traffic scenario. Initially, the state value is divided into a function value and a parameter value. Combining these two scenarios updates the resulting optimized state value. Ultimately, an analogous criterion is developed for the current dataset. Next, the error or loss value for the present scenario is computed. Furthermore, utilizing the Deep Q-learning methodology with a quad agent enhances previous study discoveries. The recommended method outperforms all other traditional approaches in effectively optimizing traffic signal timing.

Assessment of consolidative multi-criteria decision making (C-MCDM) algorithms for optimal mapping of polymer materials in additive manufacturing: A case study of orthotic application.

Objective: The objectives of this research are twofold. The primary goal is to introduce, investigate, and contrast consolidative multi-criteria decision-making (C-MCDM) approaches. The second objective is the investigation of five alternative additive manufacturing materials. Methods: It integrates the subjective and objective weights using the Bayes hypothesis in conjunction with a normal method. Chang's Extent Analysis Method under fuzzy logic is used to estimate subjective weights and the CRITIC approach is used for assessing objective weights. Ranking techniques, including the simple ranking process (SRP), multi-objective optimization based on ratio analysis (MOORA), measurement alternatives and ranking according to compromise solution (MARCOS), and technique for order preference by similarity to ideal solution (TOPSIS) are applied. It also encompasses sensitivity analysis based on Kendall's coefficient of concordance and rank reversal phenomenon analysis. Spearman's rank correlation coefficient, a weighted rank measure of correlation, and rank similarity coefficient are among the metrics used to evaluate agreement between different approaches. It entails gathering expert opinions regarding the importance of various criteria as well as conducting extensive experiments. Results: The findings of the study indicate that polylactic acid is the best material to use for orthoses. When compared to the other MCDM approaches being discussed, SRP is the most reliable approach. It is also demonstrated that the SRP, MARCOS, and TOPSIS methods are rank reversal-free. Furthermore, SRP exhibits a very poor association with the TOPSIS technique but a strong correlation with the MOORA and MARCOS approaches. Conclusions: To ensure results reliability, it is necessary to consider both the subjectivity and objectivity of weights as well as apply multiple MCDM methodologies in addition to sensitivity analysis.

Breast cancer diagnosis using support vector machine optimized by improved quantum inspired grey wolf optimization.

A prompt diagnosis of breast cancer in its earliest phases is necessary for effective treatment. While Computer-Aided Diagnosis systems play a crucial role in automated mammography image processing, interpretation, grading, and early detection of breast cancer, existing approaches face limitations in achieving optimal accuracy. This study addresses these limitations by hybridizing the improved quantum-inspired binary Grey Wolf Optimizer with the Support Vector Machines Radial Basis Function Kernel. This hybrid approach aims to enhance the accuracy of breast cancer classification by determining the optimal Support Vector Machine parameters. The motivation for this hybridization lies in the need for improved classification performance compared to existing optimizers such as Particle Swarm Optimization and Genetic Algorithm. Evaluate the efficacy of the proposed IQI-BGWO-SVM approach on the MIAS dataset, considering various metric parameters, including accuracy, sensitivity, and specificity. Furthermore, the application of IQI-BGWO-SVM for feature selection will be explored, and the results will be compared. Experimental findings demonstrate that the suggested IQI-BGWO-SVM technique outperforms state-of-the-art classification methods on the MIAS dataset, with a resulting mean accuracy, sensitivity, and specificity of 99.25%, 98.96%, and 100%, respectively, using a tenfold cross-validation datasets partition.

An Insight into the Characteristics of 3D Printed Polymer Materials for Orthoses Applications: Experimental Study.

Knee orthoses assist patients with impaired gait through the amendment of knee abnormalities, restoration of mobility, alleviation of pain, shielding, and immobilization. The inevitable issues with laborious traditional plaster molding procedures for orthoses can be resolved with 3D printing. However, a number of challenges have limited the adoption of 3D printing, the most significant of which is the proper material selection for orthoses. This is so because the material used to make an orthosis affects its strength, adaptability, longevity, weight, moisture response, etc. This study intends to examine the mechanical, physical, and dimensional characteristics of three-dimensional (3D) printing materials (PLA, ABS, PETG, TPU, and PP). The aim of this investigation is to gain knowledge about these materials' potential for usage as knee orthosis materials. Tensile testing, Olympus microscope imaging, water absorption studies, and coordinate measuring machine-based dimension analysis are used to characterize the various 3D printing materials. Based on the investigation, PLA outperforms all other materials in terms of yield strength (25.98 MPa), tensile strength (30.89 MPa), and shrinkage (0.46%). PP is the least water absorbent (0.15%) and most flexible (407.99%); however, it is the most difficult to fabricate using 3D printing. When producing knee orthoses with 3D printing, PLA can be used for the orthosis frame and other structural elements, PLA or ABS for moving parts like hinges, PP for padding, and TPU or PP for the straps. This study provides useful information for scientists and medical professionals who are intrigued about various polymer materials for 3D printing and their effective utilization to fabricate knee orthoses.

Neural Network Based Mental Depression Identification and Sentiments Classification Technique From Speech Signals: A COVID-19 Focused Pandemic Study.

COVID-19 (SARS-CoV-2) was declared as a global pandemic by the World Health Organization (WHO) in February 2020. This led to previously unforeseen measures that aimed to curb its spread, such as the lockdown of cities, districts, and international travel. Various researchers and institutions have focused on multidimensional opportunities and solutions in encountering the COVID-19 pandemic. This study focuses on mental health and sentiment validations caused by the global lockdowns across the countries, resulting in a mental disability among individuals. This paper discusses a technique for identifying the mental state of an individual by sentiment analysis of feelings such as anxiety, depression, and loneliness caused by isolation and pauses to the normal chains of operations in daily life. The research uses a Neural Network (NN) to resolve and extract patterns and validate threshold trained datasets for decision making. This technique was used to validate 2,173 global speech samples, and the resulting accuracy of mental state and sentiments are identified with 93.5% accuracy in classifying the behavioral patterns of patients suffering from COVID-19 and pandemic-influenced depression.

A Hybrid Approach of ANFIS-Artificial Bee Colony Algorithm for Intelligent Modeling and Optimization of Plasma Arc Cutting on Monel™ 400 Alloy.

This paper focusses on a hybrid approach based on genetic algorithm (GA) and an adaptive neuro fuzzy inference system (ANFIS) for modeling the correlation between plasma arc cutting (PAC) parameters and the response characteristics of machined Monel 400 alloy sheets. PAC experiments are performed based on box-behnken design methodology by considering cutting speed, gas pressure, arc current, and stand-off distance as input parameters, and surface roughness (Ra), kerf width (kw), and micro hardness (mh) as response characteristics. GA is efficaciously utilized as the training algorithm to optimize the ANFIS parameters. The training, testing errors, and statistical validation parameter results indicated that the ANFIS learned by GA outperforms in the forecasting of PAC responses compared with the results of multiple linear regression models. Besides that, to obtain the optimal combination PAC parameters, multi-response optimization was performed using a trained ANFIS network coupled with an artificial bee colony algorithm (ABC). The superlative responses, such as Ra of 1.5387 µm, kw of 1.2034 mm, and mh of 176.08, are used to forecast the optimum cutting conditions, such as a cutting speed of 2330.39 mm/min, gas pressure of 3.84 bar, arc current of 45 A, and stand-off distance of 2.01 mm, respectively. Furthermore, the ABC predicted results are validated by conducting confirmatory experiments, and it was found that the error between the predicted and the actual results are lower than 6.38%, indicating the adoptability of the proposed ABC in optimizing real-world complex machining processes.

Engineering and Characterization of Antibacterial Coaxial Nanofiber Membranes for Oil/Water Separation.

In the present study, a coaxial nanofiber membrane was developed using the electrospinning technique. The developed membranes were fabricated from hydrophilic cellulose acetate (CA) polymer and hydrophobic polysulfone (PSf) polymer as a core and shell in an alternative way with addition of 0.1 wt.% of ZnO nanoparticles (NPs). The membranes were treated with a 2M NaOH solution to enhance hydrophilicity and thus increase water separation flux. Chemical and physical characterizations were performed, such as Fourier transform infrared (FTIR) spectroscopy, and surface wettability was measured by means of water contact angle (WCA), mechanical properties, surface morphology via field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and microscopy energy dispersive (EDS) mapping and point analysis. The results show higher mechanical properties for the coaxial nanofiber membranes which reached a tensile strength of 7.58 MPa, a Young's modulus of 0.2 MPa, and 23.4 M J.m-3 of toughness. However, treated mebranes show lower mechanical properties (tensile strength of 0.25 MPa, Young's modulus of 0.01 MPa, and 0.4 M J.m-3 of toughness). In addition, the core and shell nanofiber membranes showed a uniform distribution of coaxial nanofibers. Membranes with ZnO NPs showed a porous structure and elimination of nanofibers after treatment due to the formation of nanosheets. Interestingly, membranes changed from hydrophobic to hydrophilic (the WCA changed from 90 ± 8° to 14 ± 2°). Besides that, composite nanofiber membranes with ZnO NPs showed antibacterial activity against Escherichia coli. Furthermore, the water flux for the modified membranes was improved by 1.6 times compared to the untreated membranes.

A Heuristic Angular Clustering Framework for Secured Statistical Data Aggregation in Sensor Networks.

Clustering in wireless sensor networks plays a vital role in solving energy and scalability issues. Although multiple deployment structures and cluster shapes have been implemented, they sometimes fail to produce the expected outcomes owing to different geographical area shapes. This paper proposes a clustering algorithm with a complex deployment structure called radial-shaped clustering (RSC). The deployment structure is divided into multiple virtual concentric rings, and each ring is further divided into sectors called clusters. The node closest to the midpoint of each sector is selected as the cluster head. Each sector's data are aggregated and forwarded to the sink node through angular inclination routing. We experimented and compared the proposed RSC performance against that of the existing fan-shaped clustering algorithm. Experimental results reveal that RSC outperforms the existing algorithm in scalability and network lifetime for large-scale sensor deployments.

Prediction and Analysis of Multi-Response Characteristics on Plasma Arc Cutting of Monel 400™ Alloy Using Mamdani-Fuzzy Logic System and Sensitivity Analysis.

Nickel-based alloys, especially Monel 400™, is gaining its significance in diverse applications owing to its superior mechanical properties and high corrosion resistance. Machining of these materials is extremely difficult through the traditional manufacturing process because of their affinity to rapid work hardening and deprived thermal conductivity. Owing to these difficulties a well-established disruptive metal cutting process namely plasma arc cutting (PAC) can be widely used to cut the sheet metals with intricate profiles. The present work focuses on an intelligent modeling of the PAC process and investigation on the multi-quality characteristics of PAC parameters using the fuzzy logic approach. The Box-Behnken response surface methodology is incorporated to design and conduct the experiments, and to establish the relationship between PAC parameters such as cutting speed, gas pressure, arc current, and stand-off distance and responses which include the material removal rate (MRR), kerf taper (KT), and heat affected zone (HAZ). The quadratic regression models are developed and their performances are assessed using the analysis of variance (ANOVA). Fuzzy set theory-based models are formulated to predict various responses using the Mamdani approach. Fuzzy logic and regression results are compared with the experimental data. A comparative evaluation predicted an average error of 0.04% for MRR, 0.48% for KT, and 0.46% for HAZ, respectively. The effect of variations in PAC process parameters on selected responses are estimated through performing the sensitivity analysis.