Retarding Ion Migration for Stable Blade-Coated Inverted Perovskite Solar Cells.

The fabrication of perovskite solar cells (PSCs) through blade coating is seen as one of the most viable paths toward commercialization. However, relative to the less scalable spin coating method, the blade coating process often results in more defective perovskite films with lower grain uniformity. Ion migration, facilitated by those elevated defect levels, is one of the main triggers of phase segregation and device instability. Here, a bifunctional molecule, p-aminobenzoic acid (PABA), which enhances the barrier to ion migration, induces grain growth along the (100) facet, and promotes the formation of homogeneous perovskite films with fewer defects, is reported. As a result, PSCs with PABA achieved impressive power conversion efficiencies (PCEs) of 23.32% and 22.23% for devices with active areas of 0.1 cm2 and 1 cm2 , respectively. Furthermore, these devices maintain 93.8% of their initial efficiencies after 1 000 h under 1-sun illumination, 75 °C, and 10% relative humidity conditions.

One-Pot Colloidal Synthesis Enables Highly Tunable InSb Short-Wave Infrared Quantum Dots Exhibiting Carrier Multiplication.

Colloidal quantum dots (CQDs) are emerging materials for short-wave infrared (SWIR, ≈1100-3000 nm) photodetectors, which are technologically important for a broad array of applications. Unfortunately, the most developed SWIR CQD systems are Pb and Hg chalcogenides; their toxicity and regulated compositions limit their applications. InSb CQD system is a potential environmentally friendly alternative, whose bandgap in theory, is tunable via quantum confinement across the SWIR spectrum. However, InSb CQDs are difficult to exploit, due to their complex syntheses and uncommon reactive precursors, which greatly hinder their application and study. Here, a one-pot synthesis strategy is reported using commercially available precursors to synthesize-under standard colloidal synthesis conditions-high-quality, size-tunable InSb CQDs. With this strategy, the large Bohr exciton radius of InSb can be exploited for tuning the bandgap of the CQDs over a wide range of wavelengths (≈1250-1860 nm) across the SWIR region. Furthermore, by changing the surface ligands of the CQDs from oleic acid (OA) to 1-dodecanthiol (DDT), a ≈20-fold lengthening in the excited-state lifetime, efficient carrier multiplication, and slower carrier annihilation are observed. The work opens a wide range of SWIR applications to a promising class of Pb- and Hg-free CQDs.

InAs Nanorod Colloidal Quantum Dots with Tunable Bandgaps Deep into the Short-Wave Infrared.

InAs colloidal quantum dots (CQDs) have emerged as candidate lead- and mercury-free solution-processed semiconductors for infrared technology due to their appropriate bulk bandgap, which can be tuned by quantum confinement, and promising charge-carrier transport properties. However, the lack of suitable arsenic precursors and readily accessible synthesis conditions have limited InAs CQDs to smaller sizes (<7 nm), with bandgaps largely restricted to <1400 nm in the near-infrared spectral window. Conventional InAs CQD synthesis requires highly reactive, hazardous arsenic precursors, which are commercially scarce, making the synthesis hard to control and study. Here, we present a controlled synthesis strategy (using only readily available and less reactive precursors) to overcome the practical wavelength limitation of InAs CQDs, achieving monodisperse InAs nanorod CQDs with bandgaps tunable from ∼1200 to ∼1800 nm, thus crossing deep into the short-wave infrared (SWIR) region. By controlling the reactivity through in situ precursor complexation, we isolate the reaction mechanism, producing InAs nanorod CQDs that display narrow excitonic features and efficient carrier multiplication. Our work enables InAs CQDs for a wider range of SWIR applications.

Fast and Effective Deactivation of Human Coronavirus with Copper Oxide Suspensions.

The COVID-19 pandemic has demonstrated the need for versatile and robust countermeasures against viral threats. A wide range of viruses, including SARS-CoV-2, the virus that causes COVID-19, can be deactivated by metal and metal-oxide surface coatings. However, such coatings are expensive and cannot easily be retrofitted to existing infrastructure. Low-cost materials to halt the propagation of a variety of viruses must be produced with minimal quantities of expensive precursors. In this regard, we show that commercially available copper oxide nanoparticle suspensions can deactivate more than 99.55% of the human coronavirus 229E in 30 min, confirming the particles' efficiency as a fast antiviral material.

Microwave-Assisted Non-aqueous and Low-Temperature Synthesis of Titania and Niobium-Doped Titania Nanocrystals and Their Application in Halide Perovskite Solar Cells as Electron Transport Layers.

Undoped and Nb-doped TiO2 nanocrystals are prepared by a microwave-assisted non-aqueous sol-gel method based on a slow alkyl chloride elimination reaction between metal chlorides and benzyl alcohol. Sub-4 nm nanoparticles are grown under microwave irradiation at 80 °C in only 3 h with precise control of growth parameters and yield. The obtained nanocrystals could be conveniently used to cast compact TiO2 or Nb-doped TiO2 electron transport layers for application in formamidinium lead iodide-based photovoltaic devices. Niobium doping is found to improve the cell performance by increasing the conductivity and mobility of the electron transport layer. At the same time, a measurable decrease in parasitic light absorption in the low wavelength portion of the spectrum was observed.

Silver Nanoparticle-Decorated Personal Protective Equipment for Inhibiting Human Coronavirus Infectivity.

The Coronavirus disease 2019 (COVID-19) global outbreak and its continued growth and mutation into various forms emphasize the need for effective disinfectants to assist in the reduction of the virus's spread from individual to individuals and community to communities through various modes, including coughing, sneezing, touching of contaminated surfaces, and being in proximity of an unprotected infected person, to mention a few. The rapid development of reliable disinfecting materials or solutions and their incorporation in personal protective equipment is a critical need at the moment that will assist significantly in curbing the spread of the virus SARS-CoV-2, the cause of COVID-19 illness. Here, we present an in situ assembly of antiviral metal nanoparticles on a rigid surface and on commercial face masks made up of nonwoven and woven textiles. The results indicate a very high efficacy of 99.99% against a surrogate virus to SARS-CoV-2. Such a versatile and cost-effective approach using the blade-coating technique can be easily extended to the roll-to-roll manufacturing setting to expedite the efforts and mitigate the rapid spread of the virus.

Annealing temperature effects on photoelectrochemical performance of bismuth vanadate thin film photoelectrodes.

The effects of annealing treatment between 400 °C and 540 °C on crystallization behavior, grain size, electrochemical (EC) and photoelectrochemical (PEC) oxygen evolution reaction (OER) performances of bismuth vanadate (BiVO4) thin films are investigated in this work. The results show that higher temperature leads to larger grain size, improved crystallinity, and better crystal orientation for the BiVO4 thin film electrodes. Under air-mass 1.5 global (AM 1.5) solar light illumination, the BiVO4 thin film prepared at a higher annealing temperature (500-540 °C) shows better PEC OER performance. Also, the OER photocurrent density increased from 0.25 mA cm-2 to 1.27 mA cm-2 and that of the oxidation of sulfite, a hole scavenger, increased from 1.39 to 2.53 mA cm-2 for the samples prepared from 400 °C to 540 °C. Open-circuit photovoltage decay (OCPVD) measurement indicates that BiVO4 samples prepared at the higher annealing temperature have less charge recombination and longer electron lifetime. However, the BiVO4 samples prepared at lower annealing temperature have better EC performance in the absence of light illumination and more electrochemically active surface sites, which are negatively related to electrochemical double-layer capacitance (C dl). C dl was 0.0074 mF cm-2 at 400 °C and it decreased to 0.0006 mF cm-2 at 540 °C. The OER and sulfide oxidation are carefully compared and these show that the efficiency of charge transport in the bulk (η bulk) and on the surface (η surface) of the BiVO4 thin film electrode are improved with the increase in the annealing temperature. The mechanism behind the light-condition-dependent role of the annealing treatment is also discussed.

Amorphous Tin Oxide as a Low-Temperature-Processed Electron-Transport Layer for Organic and Hybrid Perovskite Solar Cells.

Chemical bath deposition (CBD) of tin oxide (SnO2) thin films as an electron-transport layer (ETL) in a planar-heterojunction n-i-p organohalide lead perovskite and organic bulk-heterojunction (BHJ) solar cells is reported. The amorphous SnO2 (a-SnO2) films are grown from a nontoxic aqueous bath of tin chloride at a very low temperature (55 °C) and do not require postannealing treatment to work very effectively as an ETL in a planar-heterojunction n-i-p organohalide lead perovskite or organic BHJ solar cells, in lieu of the commonly used ETL materials titanium oxide (TiO2) and zinc oxide (ZnO), respectively. Ultraviolet photoelectron spectroscopy measurements on the glass/indium-tin oxide (ITO)/SnO2/methylammonium lead iodide (MAPbI3)/2,2',7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene device stack indicate that extraction of photogenerated electrons is facilitated by a perfect alignment of the conduction bands at the SnO2/MAPbI3 interface, while the deep valence band of SnO2 ensures strong hole-blocking properties. Despite exhibiting very low electron mobility, the excellent interfacial energetics combined with high transparency (Egap,optical > 4 eV) and uniform substrate coverage make the a-SnO2 ETL prepared by CBD an excellent candidate for the potentially low-cost and large-scale fabrication of organohalide lead perovskite and organic photovoltaics.

Nano-design of quantum dot-based photocatalysts for hydrogen generation using advanced surface molecular chemistry.

Efficient photocatalytic hydrogen generation in a suspension system requires a sophisticated nano-device that combines a photon absorber with effective redox catalysts. This study demonstrates an innovative molecular linking strategy for fabricating photocatalytic materials that allow effective charge separation of excited carriers, followed by efficient hydrogen evolution. The method for the sequential replacement of ligands with appropriate molecules developed in this study tethers both quantum dots (QDs), as photosensitizers, and metal nanoparticles, as hydrogen evolution catalysts, to TiO2 surfaces in a controlled manner at the nano-level. Combining hydrophobic and hydrophilic interactions on the surface, CdSe-ZnS core-shell QDs and an Au-Pt alloy were attached to TiO2 without overlapping during the synthesis. The resultant nano-photocatalysts achieved substantially high-performance visible-light-driven photocatalysis for hydrogen evolution. All syntheses were conducted at room temperature and in ambient air, providing a promising route for fabricating visible-light-responsive photocatalysts.

In Situ synthesis of self-assembled gold nanoparticles on glass or silicon substrates through reactive inkjet printing.

A facile and low cost method for the synthesis of self-assembled nanoparticles (NPs) with minimal size variation and chemical waste by using reactive inkjet printing was developed. Gold NPs with diameters as small as (8±2) nm can be made at low temperature (120 °C). The size of the resulting NPs can be readily controlled through the concentration of the gold precursor and oleylamine ink. The pure gold composition of the synthesized NPs was confirmed by energy-dispersive X-ray spectroscopy (EDXS) analysis. High-resolution SEM (HRSEM) and TEM (HRTEM), and X-ray diffraction revealed their size and face-centered cubic (fcc) crystal structure, respectively. Owing to the high density of the NP film, UV/Vis spectroscopy showed a red shift in the intrinsic plasmonic resonance peak. We envision the extension of this approach to the synthesis of other nanomaterials and the production of tailored functional nanomaterials and devices.

Size-tunable phosphorescence in colloidal metastable gamma-Ga2O3 nanocrystals.

We report a colloidal synthesis of gallium oxide (Ga(2)O(3)) nanocrystals having metastable cubic crystal structure (gamma phase) and uniform size distribution. Using the synthesized nanocrystal size series we demonstrate for the first time a size-tunable photoluminescence in Ga(2)O(3) from ultraviolet to blue, with the emission shifting to lower energies with increasing nanocrystal size. The observed photoluminescence is dominated by defect-based donor-acceptor pair recombination and has a lifetime of several milliseconds. Importantly, the decay of this phosphorescence is also size dependent. The phosphorescence energy and the decay rate increase with decreasing nanocrystal size, owing to a reduced donor-acceptor separation. These results allow for a rational and predictable tuning of the optical properties of this technologically important material and demonstrate the possibility of manipulating the localized defect interactions via nanocrystal size. Furthermore, the same defect states, particularly donors, are also implicated in electrical conductivity rendering monodispersed Ga(2)O(3) nanocrystals a promising material for multifunctional optoelectronic structures and devices.