Enzymatic hydrolysis of poly(ethyleneterephthalate) used for and analysed by pore modification of track-etched membranes.

The potential of limited enzymatic poly(ethylene terephthalate) (PET) surface hydrolysis for the modification of track-etched (TE) membranes was investigated. Cutinases 1 and 2 from Thermobifida cellulosilytica as well as a fusion protein of cutinase 1 with the polymer binding module from the polyhydroxyalkanoate depolymerase of Alcaligenes faecalis (Thc_Cut1_PBM) were shown to hydrolyse highly crystalline PET TE membranes with a pore diameter of ∼120nm at very narrow size distribution. Furthermore the effects of surface chemistry were investigated by comparison of enzymatic hydrolysis by Thc_Cut1_PBM of "as received" PET TE membranes with two surface functionalized versions towards a "hydrophilic" and a more "hydrophobic" surface. The effects of adsorbed protein and the efficacy of cleaning steps after enzymatic treatment were elucidated by complementary methods for surface analysis and membrane characterization. With the optimized cleaning protocol, all adsorbed protein could be removed from the enzyme-treated membranes and effects of chemical surface functionalization of the PET TE membranes were demonstrated. The highest efficiency of enzymatic surface hydrolysis was observed for the original PET TE membranes, leading to an 0.36% weight loss corresponding to a removal of ∼3nm PET from the entire surface of the porous membrane. This correlates very well with the measured increase of barrier pore diameter by 4nm (a radius reduction? of 2nm), leading to about a two-fold increased water permeability.

Exploring mild enzymatic sustainable routes for the synthesis of bio-degradable aromatic-aliphatic oligoesters.

The application of Candida antarctica lipase B in enzyme-catalyzed synthesis of aromatic-aliphatic oligoesters is here reported. The aim of the present study is to systematically investigate the most favorable conditions for the enzyme catalyzed synthesis of aromatic-aliphatic oligomers using commercially available monomers. Reaction conditions and enzyme selectivity for polymerization of various commercially available monomers were considered using different inactivated/activated aromatic monomers combined with linear polyols ranging from C2 to C12 . The effect of various reaction solvents in enzymatic polymerization was assessed and toluene allowed to achieve the highest conversions for the reaction of dimethyl isophthalate with 1,4-butanediol and with 1,10-decanediol (88 and 87% monomer conversion respectively). Mw as high as 1512 Da was obtained from the reaction of dimethyl isophthalate with 1,10-decanediol. The obtained oligomers have potential applications as raw materials in personal and home care formulations, for the production of aliphatic-aromatic block co-polymers or can be further functionalized with various moieties for a subsequent photo- or radical polymerization.

Biocatalyzed approach for the surface functionalization of poly(L-lactic acid) films using hydrolytic enzymes.

Poly(lactic acid) as a biodegradable thermoplastic polyester has received increasing attention. This renewable polyester has found applications in a wide range of products such as food packaging, textiles and biomedical devices. Its major drawbacks are poor toughness, slow degradation rate and lack of reactive side-chain groups. An enzymatic process for the grafting of carboxylic acids onto the surface of poly(L-lactic acid) (PLLA) films was developed using Candida antarctica lipase B as a catalyst. Enzymatic hydrolysis of the PLLA film using Humicola insolens cutinase in order to increase the number of hydroxyl and carboxylic groups on the outer polymer chains for grafting was also assessed and showed a change of water contact angle from 74.6 to 33.1° while the roughness and waviness were an order of magnitude higher in comparison to the blank. Surface functionalization was demonstrated using two different techniques, (14) C-radiochemical analysis and X-ray photoelectron spectroscopy (XPS) using (14) C-butyric acid sodium salt and 4,4,4-trifluorobutyric acid as model molecules, respectively. XPS analysis showed that 4,4,4-trifluorobutyric acid was enzymatically coupled based on an increase of the fluor content from 0.19 to 0.40%. The presented (14) C-radiochemical analyses are consistent with the XPS data indicating the potential of enzymatic functionalization in different reaction conditions.

Fusion of binding domains to Thermobifida cellulosilytica cutinase to tune sorption characteristics and enhancing PET hydrolysis.

A cutinase from Thermomyces cellullosylitica (Thc_Cut1), hydrolyzing the synthetic polymer polyethylene terephthalate (PET), was fused with two different binding modules to improve sorption and thereby hydrolysis. The binding modules were from cellobiohydrolase I from Hypocrea jecorina (CBM) and from a polyhydroxyalkanoate depolymerase from Alcaligenes faecalis (PBM). Although both binding modules have a hydrophobic nature, it was possible to express the proteins in E. coli . Both fusion enzymes and the native one had comparable kcat values in the range of 311 to 342 s(-1) on pNP-butyrate, while the catalytic efficiencies kcat/Km decreased from 0.41 s(-1)/ µM (native enzyme) to 0.21 and 0.33 s(-1)/µM for Thc_Cut1+PBM and Thc_Cut1+CBM, respectively. The fusion enzymes were active both on the insoluble PET model substrate bis(benzoyloxyethyl) terephthalate (3PET) and on PET although the hydrolysis pattern was differed when compared to Thc_Cut1. Enhanced adsorption of the fusion enzymes was visible by chemiluminescence after incubation with a 6xHisTag specific horseradish peroxidase (HRP) labeled probe. Increased adsorption to PET by the fusion enzymes was confirmed with Quarz Crystal Microbalance (QCM-D) analysis and indeed resulted in enhanced hydrolysis activity (3.8× for Thc_Cut1+CBM) on PET, as quantified, based on released mono/oligomers.