Amorphous Boron Carbide on Titanium Dioxide Nanobelt Arrays for High-Efficiency Electrocatalytic NO Reduction to NH3.

Electrocatalytic NO reduction is regarded as an attractive strategy to degrade the NO contaminant into useful NH3 , but the lack of efficient and stable electrocatalysts to facilitate such multiple proton-coupled electron-transfer processes impedes its applications. Here, we report on developing amorphous B2.6 C supported on a TiO2 nanoarray on a Ti plate (a-B2.6 C@TiO2 /Ti) as an NH3 -producing nanocatalyst with appreciable activity and durability toward the NO electroreduction. It shows a yield of 3678.6 µg h-1 cm-2 and a FE of 87.6 %, superior to TiO2 /Ti (563.5 µg h-1 cm-2 , 42.6 %) and a-B2.6 C/Ti (2499.2 µg h-1 cm-2 , 85.6 %). An a-B2.6 C@TiO2 /Ti-based Zn-NO battery achieves a power density of 1.7 mW cm-2 with an NH3 yield of 1125 µg h-1 cm-2 . An in-depth understanding of catalytic mechanisms is gained by theoretical calculations.

Synthesis, Characterization, Photocatalysis, and Antibacterial Study of WO3, MXene and WO3/MXene Nanocomposite.

Tungsten oxide (WO3), MXene, and an WO3/MXene nanocomposite were synthesized to study their photocatalytic and biological applications. Tungsten oxide was synthesized by an easy and cost-effective hydrothermal method, and its composite with MXene was prepared through the sonication method. The synthesized tungsten oxide, MXene, and its composite were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Fourier transform infrared (FTIR), energy-dispersive X-ray analysis (EDX), and Brunauer-Emmett-Teller (BET) for their structural, morphological, spectral, elemental and surface area analysis, respectively. The crystallite size of WO3 calculated from XRD was ~10 nm, the particle size of WO3 was 130 nm, and the average thickness of MXene layers was 175 nm, which was calculated from FESEM. The photocatalytic activity of as-synthesized samples was carried out for the degradation of methylene blue under solar radiation, MXene, the WO3/MXene composite, and WO3 exhibited 54%, 89%, and 99% photocatalytic degradation, respectively. WO3 showed maximal degradation ability; by adding WO3 to MXene, the degradation ability of MXene was enhanced. Studies on antibacterial activity demonstrated that these samples are good antibacterial agents against positive strains, and their antibacterial activity against negative strains depends upon their concentration. Against positive strains, the WO3/MXene composite's inhibition zone was at 7 mm, while it became 9 mm upon increasing the concentration. This study proves that WO3, MXene, and the WO3/MXene nanocomposite could be used in biological and environmental applications.

Ambient Ammonia Synthesis via Electrochemical Reduction of Nitrate Enabled by NiCo2 O4 Nanowire Array.

NiCo2 O4 nanowire array on carbon cloth (NiCo2 O4 /CC) is proposed as a highly active electrocatalyst for ambient nitrate (NO3 - ) reduction to ammonia (NH3 ). In 0.1 m NaOH solution with 0.1 m NaNO3 , such NiCo2 O4 /CC achieves a high Faradic efficiency of 99.0% and a large NH3 yield up to 973.2 µmol h-1  cm-2 . The superior catalytic activity of NiCo2 O4 comes from its half-metal feature and optimized adsorption energy due to the existence of Ni in the crystal structure. A Zn-NO3 - battery with NiCo2 O4 /CC cathode also shows a record-high battery performance.

Exploring the Influence of Critical Parameters for the Effective Synthesis of High-Quality 2D MXene.

Recently, a new class of two-dimensional (2D) materials, called MXene, consisting of layers of transition-metal carbides and nitrides/carbonitrides has been introduced. MXene, a multifunctional material with hydrophilic nature and excellent electrical conductivity and chemical stabilities, can be applied in diverse research areas such as energy harvesting and its storage, water purification, thermal dissipation, and gas sensing. To achieve the best quality of MXene, optimization of some important synthetic parameters is highly required such as an optimized etchant concentration to remove an "A" element from the MAX phase and sonication time for the efficient exfoliation of MXene flakes. Besides, there is a need to disclose that particular solvent through which intercalation can easily be achieved. In this work, we optimized the abovementioned critical parameters for the synthesis of good-quality MXene. Our results clearly explain the variations in the quality of MXene under applied etchant concentrations, solvents for better intercalation, and optimization of sonication time for better exfoliation. The obtained results suggest that 30% HF as an etchant, dimethyl sulfoxide (DMSO) as a solvent, and 135 min as the sonication time are effective parameters for the synthesis of good-quality MXene. We expect that this report will be helpful for the young research community to synthesize good-quality MXene with the required properties.