Effect of Fibres on Physico-Mechanical Properties of Bulk-Fill Resin Composites.

OBJECTIVE: To measure the flexural strength (FS) of bulk-fill resin composites and assess their long-term water absorption and solubility properties with and without the inclusion of short glass fibres. METHODS: One resin composite, everX Flow with fibres, and four commercially available bulk-fill composites without fibres, namely, PALFIQUE, Activa, SDR Plus, and Filtek Bulk Fill One, were tested. Six specimens (2 × 2 × 25 mm) were fabricated for each material and stored in water for 1 day and 30 days to measure the flexural strength using a three-point bending test. To evaluate water absorption and solubility, circular disks measuring 15 × 2 mm (n = 5) were immersed in water for 60 days, and their weights were recorded periodically. After 60 days, the specimens were dried for an additional 21 days to determine solubility. RESULTS: Flexural strength values ranged from 101.7 to 149.1 MPa. Significant distinctions were observed among the resin composites at the onset of the study (p < 0.05). The highest FS value was identified in everX Flow, while ACT exhibited the lowest (p < 0.05). However, the flexural strength values exhibited a significant decrease with increased storage time (p < 0.05), except for ACT, which demonstrated a noteworthy increase. Concerning water absorption and solubility, ACT displayed the highest absorption, while the range of solubility varied from -0.88 to 5.8 µg/mm3. ACT also had the highest solubility, whereas everX Flow exhibited negative solubility. SIGNIFICANCE: The addition of short fibres, along with potential differences in matrix composition, enhanced the flexural strength of everX Flow. However, the substantial reduction in flexural strength observed in everX Flow and SDR following exposure to water corroborates the manufacturers' recommendation to apply a conventional resin composite cap on these materials.

Evaluation of the Shear Bond Strength of Four Bioceramic Materials with Different Restorative Materials and Timings.

The objectives of this study were to evaluate the shear bond strength (SBS) of a resin composite (RC) and a resin-modified glass ionomer (RMGI) to four different bioceramic materials and to compare the effects of the immediate vs. delayed placement of restoration on the SBS. A total of 160 Teflon blocks and 40 blocks/material, were randomly filled with one of the bioceramic materials (NeoPUTTY®, NeoMTA2®, TotalFill® BC RRM™ Fast Set Putty, and ProRoot® MTA). The restoration was performed immediately or in a delayed time frame (after 7 days) using a Filtek™ Z350 XT Flowable composite (bonded to the bioceramic materials using Single bond universal 3M) or GC Fuji II LC® RMGI. The SBS test was performed at a crosshead speed of 1 mm/min, and the failure mode was evaluated under a digital microscope by one blinded examiner. One-way analysis of variance (ANOVA) with the Games-Howell post hoc test was used to compare the mean SBS between the groups. The mean SBS of the bioceramic materials to RC was significantly higher than to RMGI except for ProRoot MTA (p-value 0.65). The SBS values to RC were as follows: ProRoot MTA (7.64 MPa); NeoMTA2 (8.57 MPa) which was significantly higher than both NeoPUTTY (4.04 MPa) and TotalFill® BC RRM™ Fast Set Putty (4.38 MPa). For RMGI groups, ProRoot MTA showed the highest SBS (7.18 MPa), followed by NeoMTA2 (4.15 MPa), NeoPUTTY (1.62 MPa), and TotalFill® BC RRM™ Fast Set Putty (1.54 MPa). The delayed timing restoration showed a significantly higher SBS than the immediate, except for the immediate RMGI restoration with MTA. To conclude, the SBS of RC to the bioceramic materials was significantly higher than RMGI, except for ProRoot MTA. Both restorative materials had a significantly higher SBS to the MTA groups in comparison to premixed bioceramics. Delayed RC restoration had a higher SBS than immediate restoration. Similarly, delayed RMGI restoration had a higher SBS than immediate restoration with premixed bioceramic but not with MTA.

Effectiveness of antimicrobial photodynamic therapy as an adjunct to mechanical instrumentation in reducing counts of Enterococcus faecalis and Candida albicans from C-shaped root canals.

BACKGROUND/PURPOSE: The aim was to assess the effectiveness of antimicrobial photodynamic therapy (aPDT) as an adjunct to mechanical instrumentation (MI) in reducing Enterococcus faecalis (E faecalis) and Candida albicans (C albicans) counts from C-shaped root-canals. METHODS: Teeth with C-shaped canals as identified on cone beam computed tomographic images were included. Following incubation with E faecalis and C albicans, samples were divided into 4 groups a four follows: Group-1: MI with adjunct aPDT; Group-2: aPDT alone; Group-3: MI alone; and Group-4: no treatment. The pulp chambers of these teeth were exposed and coronal pulp was mechanically derided using sterile endodontic excavators. Using flexible files, all canals were debrided up to size #30 K-files with intermittent irrigation with 2.5% sodium hypochlorite irrigation. In Groups 1 and 3, methylene-blue was injected in all canals and aPDT was performed using a 600 nm diode laser. Sample-size estimation was done on data from a pilot investigation and group-comparisons were done using one way analysis of variance and Bonferroni post-hoc adjustment tests. P < .05 was considered statistically significant. RESULTS: Sixty periodontally hopeless mandibular second molars with C-shaped canals were included. There was a statistically significant reduction CFU/mL of E faecalis (P < .001) and C albicans (P < .001). At post-operative microbial assessments in Group-1. There was no difference CFU/mL of E faecalis and C albicans at post-operative microbial assessments in Groups 2-4. CONCLUSION: MI with adjunct aPDT is more effective in reducing count of E faecalis and C albicans from C-shaped root canals.

Anatomical Shaping for Zirconia Custom Implant Abutment to Enhance Anterior Esthetic: A Clinical Technique.

Abutments are used in dentistry to attach dental crowns to dental implant. Currently, zirconia custom abutment is the one which is mostly used in restorations, since it offers several advantages, especially better esthetics and prevention from infection. Several innovations are done in the implant designs and procedures to achieve better esthetics. Computer-aided design & computer-aided manufacturing (CAD/CAM) system is widely used innovative technology in dentistry. This technology offers custom implants that help to achieve better esthetics and good internal fit. This procedure used a novel technique of anatomical modification of the final abutment incisal edge from straight anatomical edge to irregular one with a mamelon-incisal effect to enhance esthetic, shade matching, and anatomical replication of incisal structure that resembles the natural incisor. Usually, dental technicians will perform facial and incisal cut-back and apply porcelain layers to the crown in order to reproduce the translucency and the other optical effects that most closely match that of natural dentin and enamel, especially at the incisal edge. These optical effects will make the prosthetic crown look more natural and esthetically pleasant. By this presented technique will help the dental technician to achieve highly esthetic crown with completely digital workflow without the need for porcelain layering. The procedure was also followed up to 3, 6, and 12 months after the surgery and found no complications or complaints from the patient and esthetically satisfied.