Passive-Sampler-Derived PCB and OCP Concentrations in the Waters of the World─First Results from the AQUA-GAPS/MONET Network.

Persistent organic pollutants (POPs) are recognized as pollutants of global concern, but so far, information on the trends of legacy POPs in the waters of the world has been missing due to logistical, analytical, and financial reasons. Passive samplers have emerged as an attractive alternative to active water sampling methods as they accumulate POPs, represent time-weighted average concentrations, and can easily be shipped and deployed. As part of the AQUA-GAPS/MONET, passive samplers were deployed at 40 globally distributed sites between 2016 and 2020, for a total of 21 freshwater and 40 marine deployments. Results from silicone passive samplers showed α-hexachlorocyclohexane (HCH) and γ-HCH displaying the greatest concentrations in the northern latitudes/Arctic Ocean, in stark contrast to the more persistent penta (PeCB)- and hexachlorobenzene (HCB), which approached equilibrium across sampling sites. Geospatial patterns of polychlorinated biphenyl (PCB) aqueous concentrations closely matched original estimates of production and use, implying limited global transport. Positive correlations between log-transformed concentrations of Σ7PCB, ΣDDTs, Σendosulfan, and Σchlordane, but not ΣHCH, and the log of population density (p < 0.05) within 5 and 10 km of the sampling sites also supported limited transport from used sites. These results help to understand the extent of global distribution, and eventually time-trends, of organic pollutants in aquatic systems, such as across freshwaters and oceans. Future deployments will aim to establish time-trends at selected sites while adding to the geographical coverage.

Identification of polystyrene nanoplastics from natural organic matter in complex environmental matrices by pyrolysis-gas chromatography-mass spectrometry.

Due to the flux of plastic debris entering the environment, it becomes urgent to document and monitor their degradation pathways at different scales. At the colloidal scale, the systematic hetero-association of nanoplastics with the natural organic matter complexifies the ability to detect plastic signatures in the particle collected in the various environments. The current techniques used for microplastics could not discriminate the polymers at the nanoscale from the natural macromolecules, as the plastic mass in the aggregate is within the same order. Only a few methods are available concerning nanoplastics identification in complex matrices, with the coupling of pyrolysis with gas chromatography and mass spectrometry (Py-GC-MS) as one of the most promising due to its mass-based detection. However, natural organic matter in environmental samples interferes with similar pyrolysis products. These interferences are even more critical for polystyrene polymers as this plastic presents no dominant pyrolysis markers, such as polypropylene, that could be identified at trace concentrations. Here, we investigate the ability to detect and quantify polystyrene nanoplastics in a rich phase of natural organic matter proposed based on the relative ratio of pyrolyzates. The use of specific degradation products (styrene dimer and styrene trimer) and the toluene/styrene ratio (RT/S) are explored for these two axes. While the size of the polystyrene nanoplastics biased the pyrolyzates of styrene dimer and trimer, the RT/S was correlated with the nanoplastics mass fraction in the presence of natural organic matter. An empirical model is proposed to evaluate the relative quantity of polystyrene nanoplastics in relevant environmental matrices. The model was applied to real contaminated soil by plastic debris and literature data to demonstrate its potential.

Assessment of marine sediment remediation efficiency with SPME-based passive sampling measurement.

Passive sampling has been shown to be a suitable procedure to assess the risk of contaminated sediments through the measurement of freely dissolved concentrations (CFree) and remedial actions involving amendments such as activated carbon (AC). Here we report results of the application of simple, solvent-free solid phase micro extraction methodology (SPME) to assess the performance of different materials for the remediation of selected Norwegian harbour sediments contaminated with polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). AC amendments enabled a reduction of the availability of PAHs and/or PCBs by a factor of ten to over one hundred in Aker Brygge sediments (Oslo) and sediments from Elkembukta, impacted by industrial emissions of PAHs with/from coal tar pitch. Another material, anthracite, slightly less effective in this set of experiment than AC, showed nonetheless great promise as capping material. The SPME data are put in perspective with equilibrium measurements of CFree for PAHs and organochlorines with silicone rubber in other Elkembukta sediments collected in the vicinity of those used for the remediation experiments. A reduction of sediment Cfree for pyrene, benzo[a]pyrene and benzo[ghi]perylene in inner Elkembukta sediment from on average 407, 6.3 and 0.82 ng L-1 to values of/or below 1.3, 0.15 and 0.076 ng L-1, respectively can be expected upon remediation with AC. For the outer, less contaminated Elkembukta sediment, Cfree would reduce from 36, 0.81 and 0.13 ng L-1 to value of or below 0.06, 0.03 and 0.005 ng L-1 for these three compounds, respectively. Differences in pattern of PAH and organochlorine contamination of inner and outer Elkembukta sediments are discussed.

Partitioning of persistent hydrophobic contaminants to different storage lipid classes.

Lipids generally represent the major matrix contributing to the absorptive capacity for hydrophobic organic contaminants in aquatic ecosystems. The aim of the present study was to determine whether contaminants partition to a different degree to the different storage lipid classes: wax ester (WE) and triacylglycerol (TAG). This was undertaken by studying experimentally the partitioning of organochlorine compounds between lipids (WE or TAG) and silicone rubber phase. Our results indicate that hydrophobic compounds have a slightly higher affinity for WE than for TAG. The findings thus corroborate earlier suggestions that contaminants accumulate to a greater extent in food webs with a higher reliance of on WE, such as in the Arctic. This knowledge is of interest since it implies that possible changes in planktonic community species composition, and thereby possible changes in the lipid composition, may have consequences for accumulation of hydrophobic contaminants in apex predators. However, the magnitude of these consequences remains unknown, and there may well be other factors of importance for previously observed higher accumulation of contaminants in Arctic systems. Thus, we have here identified aspects regarding partitioning of contaminants to lipids that need further scrutiny, and there is a need for further quantitative estimates of the suggested difference in absorptive capacities for hydrophobic contaminants between WE and TAG.

Passive Samplers vs Sentinel Organisms: One-Year Monitoring of Priority and Emerging Contaminants in Coastal Waters.

Temporal monitoring of pollutants in aquatic systems impacted by human activities is mandatory for a correct assessment on their environmental impact and later management. The aim of this work was to study the suitability of using silicone rubber passive samplers and caged organisms (Ruditapes philippinarum), simultaneously, to examine the spatial and temporal variability of priority and emerging contaminants in a coastal environment (Cadiz Bay, SW Spain) over the course of an entire year. Seasonal trends were observed for some classes of compounds, such as UV filters and fragrances, and attributed to fluctuations in their sources and changes in the hydrodynamic conditions, respectively. Up to 42 out of 48 (in seawater) and 27 out of 37 (in biota) target analytes were detected, the highest concentrations being observed for synthetic fragrances and UV filters in both biota (136.9-159 ng g-1) and the dissolved phase (3322.2-265.7 ng L-1). Conversely, spatiotemporal differences in the concentrations of target contaminants in clam tissues were minimal. Higher field bioaccumulation factors (log BAF > 5) were found for priority substances. Overall, silicone rubber passive samplers proved to be more sensitive than sentinel organisms for monitoring spatiotemporal changes in the dissolved aqueous concentrations of contaminants, whereas the latter allowed for a more realistic evaluation of the potential uptake and bioaccumulation of each compound.

Detection of tris(2,3-dibromopropyl) phosphate and other organophosphorous compounds in Arctic rivers.

The flame-retardant tris(2,3-dibromopropyl) phosphate (TDBrPP) was in the 1970s banned for uses in textiles that may be in contact with the skin, owing to strong suspicions that the substance was a human carcinogen. The substance is looked for but rarely detected in samples from the built and natural environments, but there are indications that TDBrPP is still in use. Here, we report the measurement of a polymer-water partition coefficient (Kpw) for two types of silicone rubber (SR), allowing quantitative estimation of freely dissolved concentrations of TDBrPP by passive sampling in water. We found levels of 100 to 200 pg/L in two Arctic rivers that were sampled during a 2014-2015 survey of contamination using passive samplers in Norwegian and Russian rivers draining into the Barents Sea. We also report the widespread presence of other organophosphorus flame retardants in this survey of eight rivers that drain into the Barents Sea.

Comparison of caged and native blue mussels (Mytilus edulis spp.) for environmental monitoring of PAH, PCB and trace metals.

Contaminant bioaccumulation was studied in blue mussels (Mytilus edulis spp.) using the harbor waters of Kristiansand (Norway) as a case study. A suite of chemical contaminants (trace metals, PAHs and PCBs) was analyzed in caged and native mussels as well as in passive samplers (Diffusive Gradients in Thin films (DGT)-devices and silicone rubbers) placed alongside the mussels for estimation of contaminant concentrations in water and uptake rates and bioaccumulation factors (BAFs) in mussels during a six-months deployment period. Estimated logBAFs were in the ranges 2.3-5.5, 3.8-5.2 and 3.2-4.4 for metals, PCBs and PAHs, respectively. Contaminant levels in caged mussels increased rapidly to stable levels for trace metals, whereas for hydrophobic organic contaminants the increase was steady but slow and for many compounds did not reach the levels observed in native mussels. Some key issues related to mussel caging design, such as mussel deployment time and confounding influence from seasonal fluctuations, are discussed herein.

Blue mussels (Mytilus edulis spp.) as sentinel organisms in coastal pollution monitoring: A review.

The blue mussel (Mytilus spp.) is widely used as a bioindicator for monitoring of coastal water pollution (mussel watch programs). Herein we provide a review of this study field with emphasis on: the suitability of Mytilus spp. as environmental sentinels; uptake and bioaccumulation patterns of key pollutant classes; the use of Mytilus spp. in mussel watch programs; recent trends in Norwegian mussel monitoring; environmental quality standards and background concentrations of key contaminants; pollutant effect biomarkers; confounding factors; particulate contaminants (microplastics, engineered nanomaterials); climate change; harmonization of monitoring procedures; and the use of deployed mussels (transplant caging) in pollution monitoring. Lastly, the overall state of the art of blue mussel pollution monitoring is discussed and some important issues for future research and development are highlighted.

Aquatic Global Passive Sampling (AQUA-GAPS) Revisited: First Steps toward a Network of Networks for Monitoring Organic Contaminants in the Aquatic Environment.

Organic contaminants, in particular persistent organic pollutants (POPs), adversely affect water quality and aquatic food webs across the globe. As of now, there is no globally consistent information available on concentrations of dissolved POPs in water bodies. The advance of passive sampling techniques has made it possible to establish a global monitoring program for these compounds in the waters of the world, which we call the Aquatic Global Passive Sampling (AQUA-GAPS) network. A recent expert meeting discussed the background, motivations, and strategic approaches of AQUA-GAPS, and its implementation as a network of networks for monitoring organic contaminants (e.g., POPs and others contaminants of concern). Initially, AQUA-GAPS will demonstrate its operating principle via two proof-of-concept studies focused on the detection of legacy and emerging POPs in freshwater and coastal marine sites using both polyethylene and silicone passive samplers. AQUA-GAPS is set up as a decentralized network, which is open to other participants from around the world to participate in deployments and to initiate new studies. In particular, participants are sought to initiate deployments and studies investigating the presence of legacy and emerging POPs in Africa, Central, and South America.

Identification of non-regulated polycyclic aromatic compounds and other markers of urban pollution in road tunnel particulate matter.

A combination of silicone rubber extraction and non-target and suspect screening by gas chromatography coupled to high-resolution time-of flight mass spectrometry was used for the identification of compounds in particulate matter (PM). Tunnel PM is a proxy for local road pollution that constitutes a hazard to the urban environment and human health. The use of silicone rubber for the extraction of PM allowed the pre-concentration of a wide range of compounds for non-target analysis while minimising the effects of the sample matrix. As expected, polycyclic aromatic compounds (PACs) constituted the major group of compounds identified, but only 5 of 50 PACs identified were amongst those regularly monitored and many of them were alkylated or contained a heteroatom. Urban markers of contamination such as organophosphate flame-retardants, phthalates, benzothiazoles, musk compounds and a plasticiser were also identified. The level of confidence for the identifications was high based on accurate mass, the pattern of fragmentation and retention. The unequivocal identification of 16 compounds, from all groups, was confirmed by co-chromatography with standards and the compounds semi-quantified. Most of the PACs identified are not regularly monitored, and the hazards they pose are therefore unknown. Some of these PACs are known to be more persistent and mobile in the environment than the EPA PAH16.

PAH Accessibility in Particulate Matter from Road-Impacted Environments.

Snowmelt, surface runoff, or stormwater releases in urban environments can result in significant discharges of particulate matter-bound polycyclic aromatic hydrocarbons (PAHs) into aquatic environments. Recently, more-specific activities such as road-tunnel washing have been identified as contributing to contaminant load to surface waters. However, knowledge of PAH accessibility in particulate matter (PM) of urban origin that may ultimately be released into urban surface waters is limited. In the present study, we evaluated the accessibility of PAHs associated with seven distinct (suspended) particulate matter samples collected from different urban sources. Laboratory-based infinite sink extractions with silicone rubber (SR) as the extractor phase demonstrated a similar pattern of PAH accessibility for most PM samples. Substantially higher accessible fractions were observed for the less-hydrophobic PAHs (between 40 and 80% of total concentrations) compared with those measured for the most-hydrophobic PAHs (<5% of total concentrations). When we focused on PAHs bound to PM from tunnel-wash waters, first-order desorption rates for PAHs with log Kow > 5.5 were found in line with those commonly found for slowly or very slowly desorbing sediment-associated contaminants. PAHs with log Kow < 5.5 were found at higher desorbing rates. The addition of detergents did not influence the extractability of lighter PAHs but increased desorption rates for the heavier PAHs, potentially contributing to increases in the toxicity of tunnel-wash waters when surfactants are used. The implications of total and accessible PAH concentrations measured in our urban PM samples are discussed in a context of management of PAH and PM emission to the surrounding aquatic environment. Although we only fully assessed PAHs in this work, further study should consider other contaminants such as OPAHs, which were also detected in all PM samples.

Photodegradation of PAHs in passive water samplers.

Losses of deuterated polycyclic aromatic hydrocarbons (PAHs) used as performance reference compounds (PRCs) in semipermeable membrane devices deployed at fifteen coastal sampling sites near Harstad harbour in Northern Norway were used to investigate photodegradation of these photosensitive compounds. Unusual PRC dissipation profiles, especially for samplers exposed <5m below the water surface are indicative of photodegradation. A strong correlation between loss rates for d12-chrysene and d12-benzo[e]pyrene with consistently higher losses of the latter was found. The observed photodegradation rates may be sufficiently high to impact PAH masses absorbed by a factor of two. This study demonstrates that photodegradation during exposure of passive water samplers needs to be taken into account, particularly with deployments close to the water surface, when using SPMD canisters, or when sampling in the Arctic.

Determination of silicone rubber and low-density polyethylene diffusion and polymer/water partition coefficients for emerging contaminants.

There is a growing interest in assessing the concentration and distribution of new nonregulated organic compounds (emerging contaminants) in the environment. The measurement of freely dissolved concentrations using conventional approaches is challenging because of the low concentrations that may be encountered and their temporally variable emissions. Absorption-based passive sampling enables the estimation of freely dissolved concentrations of hydrophobic contaminants of emerging concern in water. In the present study, calibration was undertaken for 2 polymers, low-density polyethylene (LDPE) and silicone rubber for 11 fragrances, 5 endocrine-disrupting compounds, 7 ultraviolet (UV) filters, and 8 organophosphate flame retardant compounds. Batch experiments were performed to estimate contaminant diffusion coefficients in the polymers (Dp ), which in general decreased with increasing molecular weight. The values for fragrances, endocrine-disrupting compounds, and UV filters were in ranges similar to those previously reported for polycyclic aromatic hydrocarbons, but were 1 order of magnitude lower for organophosphate flame retardant compounds. Silicone rubber had higher Dp values than LDPE and was therefore selected for further experiments to calculate polymer/water partition coefficients (KPW ). The authors observed a positive correlation between log KPW and log octanol/water partition coefficient values. Field testing of silicone rubber passive samplers was undertaken though exposure in the River Alna (Norway) for an exposure time of 21 d to estimate freely dissolved concentration. Some fragrances and UV filters were predominant over other emerging and regulated contaminants, at levels up to 1600 ng L(-1) for galaxolide and 448 ng L(-1) for octocrylene. Environ Toxicol Chem 2016;35:2162-2172. © 2016 SETAC.

Passive Sampling in Regulatory Chemical Monitoring of Nonpolar Organic Compounds in the Aquatic Environment.

We reviewed compliance monitoring requirements in the European Union, the United States, and the Oslo-Paris Convention for the protection of the marine environment of the North-East Atlantic, and evaluated if these are met by passive sampling methods for nonpolar compounds. The strengths and shortcomings of passive sampling are assessed for water, sediments, and biota. Passive water sampling is a suitable technique for measuring concentrations of freely dissolved compounds. This method yields results that are incompatible with the EU's quality standard definition in terms of total concentrations in water, but this definition has little scientific basis. Insufficient quality control is a present weakness of passive sampling in water. Laboratory performance studies and the development of standardized methods are needed to improve data quality and to encourage the use of passive sampling by commercial laboratories and monitoring agencies. Successful prediction of bioaccumulation based on passive sampling is well documented for organisms at the lower trophic levels, but requires more research for higher levels. Despite the existence of several knowledge gaps, passive sampling presently is the best available technology for chemical monitoring of nonpolar organic compounds. Key issues to be addressed by scientists and environmental managers are outlined.

Implications of observed PBDE diffusion coefficients in low density polyethylene and silicone rubber.

A film-stacking technique was used to estimate diffusion coefficients of polybrominated diphenyl ethers (PBDEs) in low density polyethylene (LDPE) and silicone rubber. Substantially higher PBDE diffusion coefficients were observed for silicone rubber (AlteSil™) than for LDPE. A much steeper decrease in LDPE diffusion coefficients was found with increasing PBDE molecular weight than that for silicone rubber. From a passive sampling point-of-view, this means that for equivalent polymer-water partition coefficients for these two materials, the mass transfer resistance for these substances in the LDPE will be significantly higher than that for silicone rubber. Boundary layer control of the uptake process for silicone rubber can be expected for PBDEs. With a microplastic perspective, the low diffusion coefficients of PBDEs and in particular of decabromo diphenyl ether (BDE 209) in LDPE imply that the polymer diffusion coefficients for these plastic additives used as flame retardants need to be taken into account when considering the risk posed by microplastic particle ingestion by marine organisms.

Optimization of the polar organic chemical integrative sampler for the sampling of acidic and polar herbicides.

This paper presents an optimization of the pharmaceutical Polar Organic Chemical Integrative Sampler (POCIS-200) under controlled laboratory conditions for the sampling of acidic (2,4-dichlorophenoxyacetic acid (2,4-D), acetochlor ethanesulfonic acid (ESA), acetochlor oxanilic acid, bentazon, dicamba, mesotrione, and metsulfuron) and polar (atrazine, diuron, and desisopropylatrazine) herbicides in water. Indeed, the conventional configuration of the POCIS-200 (46 cm(2) exposure window, 200 mg of Oasis® hydrophilic lipophilic balance (HLB) receiving phase) is not appropriate for the sampling of very polar and acidic compounds because they rapidly reach a thermodynamic equilibrium with the Oasis HLB receiving phase. Thus, we investigated several ways to extend the initial linear accumulation. On the one hand, increasing the mass of sorbent to 600 mg resulted in sampling rates (R s s) twice as high as those observed with 200 mg (e.g., 287 vs. 157 mL day(-1) for acetochlor ESA). Although detection limits could thereby be reduced, most acidic analytes followed a biphasic uptake, proscribing the use of the conventional first-order model and preventing us from estimating time-weighted average concentrations. On the other hand, reducing the exposure window (3.1 vs. 46 cm(2)) allowed linear accumulations of all analytes over 35 days, but R s s were dramatically reduced (e.g., 157 vs. 11 mL day(-1) for acetochlor ESA). Otherwise, the observation of biphasic releases of performance reference compounds (PRC), though mirroring acidic herbicide biphasic uptake, might complicate the implementation of the PRC approach to correct for environmental exposure conditions.

Passive sampling methods for contaminated sediments: risk assessment and management.

This paper details how activity-based passive sampling methods (PSMs), which provide information on bioavailability in terms of freely dissolved contaminant concentrations (Cfree ), can be used to better inform risk management decision making at multiple points in the process of assessing and managing contaminated sediment sites. PSMs can increase certainty in site investigation and management, because Cfree is a better predictor of bioavailability than total bulk sediment concentration (Ctotal ) for 4 key endpoints included in conceptual site models (benthic organism toxicity, bioaccumulation, sediment flux, and water column exposures). The use of passive sampling devices (PSDs) presents challenges with respect to representative sampling for estimating average concentrations and other metrics relevant for exposure and risk assessment. These challenges can be addressed by designing studies that account for sources of variation associated with PSMs and considering appropriate spatial scales to meet study objectives. Possible applications of PSMs include: quantifying spatial and temporal trends in bioavailable contaminants, identifying and evaluating contaminant source contributions, calibrating site-specific models, and, improving weight-of-evidence based decision frameworks. PSM data can be used to assist in delineating sediment management zones based on likelihood of exposure effects, monitor remedy effectiveness, and, evaluate risk reduction after sediment treatment, disposal, or beneficial reuse after management actions. Examples are provided illustrating why PSMs and freely dissolved contaminant concentrations (Cfree ) should be incorporated into contaminated sediment investigations and study designs to better focus on and understand contaminant bioavailability, more accurately estimate exposure to sediment-associated contaminants, and better inform risk management decisions. Research and communication needs for encouraging broader use are discussed.

Should silicone prostheses be considered for specimen banking? A pilot study into their use for human biomonitoring.

Persistent organic pollutant (POP) biomonitoring in humans is challenging and generally carried out using blood, breast milk or adipose tissue, with concentrations normalised to the lipid content of the sample matrix. The goal of this cross-sectional pilot study was to evaluate the validity and feasibility of explanted silicone prostheses as a matrix for persistent organic pollutant biomonitoring in humans. We postulate that pollutant concentrations in silicone prostheses inserted in the body will equilibrate with that in the body over time and provide a measure of the overall body burden. This study included silicone prostheses from 22 female patients of the Colosseum clinic (Oslo, Norway) collected between September 2010 and April 2012. Absorption of chlorinated and brominated POPs into silicone prostheses during implantation was observed. Relative levels of the different contaminants measured in prostheses were in agreement with those from serum and breast milk analyses from the general Norwegian population. The comparison of serum and breast milk-based literature data with prosthesis concentrations transposed into lipid-normalised concentrations supports the validity of the prosthesis measurements. The median of relative percent differences between measurements with replicate silicone prostheses from 11 patients was below 30%. Observed increases in prosthesis concentrations with patients' age were found to be very similar to literature data from studies of the Norwegian population. Silicone prostheses therefore represent a promising matrix for the biomonitoring of nonpolar and non-ionic pollutants in humans. Sample accessibility and body burden representativeness of the silicone prostheses suggest that specimen banking should be initiated.

Passive sampling for target and nontarget analyses of moderately polar and nonpolar substances in water.

The applicability of silicone rubber and low-density polyethylene (LDPE) as passive sampling materials for target and nontarget analyses of moderately polar and nonpolar substances was assessed through a field deployment of samplers along a small, polluted stream in Oslo, Norway. Silicone and LDPE samplers of identical surface area (but different volumes) were deployed at 6 sites in the River Alna for 49 d. Quantitative target analysis by gas chromatography-mass spectrometry (quadrupole, single-ion monitoring mode) demonstrated that masses of polycyclic aromatic hydrocarbons, polychlorinated biphenyls, and organochlorine compounds absorbed in the 2 polymeric materials were consistent with the current understanding of the control and mode of accumulation in these sampler materials. Some deviation was observed for decabromodiphenyl ether (BDE-209) and may be linked to the large molecular size of this substance, resulting in lower diffusivity in the LDPE. Target and nontarget analyses with gas chromatography coupled to high resolution time-of-flight mass spectrometry allowed the identification of a wide range of chemicals, including organophosphate compounds (OPCs) and musk compounds (galaxolide and tonalid). Semiquantitative analysis revealed enhanced quantities of the OPCs in silicone material, indicating some limitation in the absorption and diffusion of these substances in LDPE. Overall, silicone allows nontarget screening analysis for compounds with a wider range of log octanol-water partition coefficient values than what can be achieved with LDPE.