RESUMEN
Natural polymers such as cellulose have interesting tribo- and piezoelectric properties for paper-based energy harvesters, but their low performance in providing sufficient output power is still an impediment to a wider deployment for IoT and other low-power applications. In this study, different types of celluloses were combined with nanosized carbon fillers to investigate their effect on the enhancement of the electrical properties in the final nanogenerator devices. Cellulose pulp (CP), microcrystalline cellulose (MCC) and cellulose nanofibers (CNFs) were blended with carbon black (CB), carbon nanotubes (CNTs) and graphene nanoplatelets (GNPs). The microstructure of the nanocomposite films was characterized by scanning electron and probe microscopies, and the electrical properties were measured macroscopically and at the local scale by piezoresponse force microscopy. The highest generated output voltage in triboelectric mode was obtained from MCC films with CNTs and CB, while the highest piezoelectric voltage was produced in CNF-CNT films. The obtained electrical responses were discussed in relation to the material properties. Analysis of the microscopic response shows that pulp has a higher local piezoelectric d33 coefficient (145 pC/N) than CNF (14 pC/N), while the macroscopic response is greatly influenced by the excitation mode and the effective orientation of the crystals relative to the mechanical stress. The increased electricity produced from cellulose nanocomposites may lead to more efficient and biodegradable nanogenerators.
RESUMEN
Increasing energy autonomy and lowering dependence on lithium-based batteries are more and more appealing to meet our current and future needs of energy-demanding applications such as data acquisition, storage, and communication. In this respect, energy harvesting solutions from ambient sources represent a relevant solution by unravelling these challenges and giving access to an unlimited source of portable/renewable energy. Despite more than five decades of intensive study, most of these energy harvesting solutions are exclusively designed from ferroelectric ceramics such as Pb(Zr,Ti)O3 and/or ferroelectric polymers such as polyvinylidene fluoride and its related copolymers, but the large implementation of these piezoelectric materials into these technologies is environmentally problematic, related with elevated toxicity and poor recyclability. In this work, we reveal that fully biobased non-isocyanate polyurethane-based materials could afford a sustainable platform to produce piezoelectric materials of high interest. Interestingly, these non-isocyanate polyurethanes (NIPUs) with ferroelectric properties could be successfully synthesized using a solvent-free reactive extrusion process on the basis of an aminolysis reaction between resorcinol bis-carbonate and different diamine extension agents. Structure-property relationships were established, indicating that the ferroelectric behavior of these NIPUs depends on the nanophase separation inside these materials. These promising results indicate a significant potential for fulfilling the requirements of basic connected sensors equipped with low-power communication technologies.
RESUMEN
Herein we report on novel multiferroic core-shell nanostructures of cobalt ferrite (CoFe2O4)-bismuth, sodium titanate doped with barium titanate (BNT-BT0.08), prepared by a two-step wet chemical procedure, using the sol-gel technique. The fraction of CoFe2O4 was varied from 1:0.5 to 1:1.5 = BNT-BT0.08/CoFe2O4 (molar ratio). X-ray diffraction confirmed the presence of both the spinel CoFe2O4 and the perovskite Bi0.5Na0.5TiO3 phases. Scanning electron microscopy analysis indicated that the diameter of the core-shell nanoparticles was between 15 and 40 nm. Transmission electron microscopy data showed two-phase composite nanostructures consisting of a BNT-BT0.08 core surrounded by a CoFe2O4 shell with an average thickness of 4-7 nm. Cole-Cole plots reveal the presence of grains and grain boundary effects in the BNT-BT0.08/CoFe2O4 composite. Moreover, the values of the dc conductivity were found to increase with the amount of CoFe2O4 semiconductive phase. Both X-ray photoelectron spectroscopy (XPS) and Mössbauer measurements have shown no change in the valence of the Fe3+, Co2+, Bi3+ and Ti4+ cations. This study provides a detailed insight into the magnetoelectric coupling of the multiferroic BNT-BT0.08/CoFe2O4 core-shell composite potentially suitable for magnetoelectric applications.
RESUMEN
Li- and Ta-modified K 0.5 Na 0.5 NbO 3 compounds are among the most promising lead-free ferroelectrics for high-sensitivity piezoelectric ceramic materials, and are potentially capable of replacing Pb(Zr,Ti)O 3 . They are also being investigated as piezoelectric components in environmentally friendly magnetoelectric composites. However, most suitable modifications for this application have not been identified. We report here a simulation study of how the magnetoelectric voltage responses of layered composite structures based on Li x (K 0.5 Na 0.5 ) 1 - x Nb 1 - y Ta y O 3 varies with the chemical composition of the piezoelectric. Instead of relying on material coefficients from the literature, which would have required using different sources, an ad hoc set of materials was prepared. This demanded tailoring preparation by conventional means to obtain dense ceramics while controlling alkali volatilization, perovskite phase and microstructure, as well as characterizing their dielectric, elastic and electromechanical properties. This provided the set of relevant material coefficients as a function of composition, which was used to obtain the magnetoelectric responses of model layered structures including a reference magnetostrictive spinel oxide by simulation. The piezoelectric material leading to the highest magnetoelectric coefficient was identified, and shown to be different to that showing the highest piezoelectric coefficient. This reflects the dependence of the magnetoelectric response on all material coefficients, along with the complex interplay between composition, processing and properties in K 0.5 Na 0.5 NbO 3 -based ceramics.
RESUMEN
Composite materials consisting of two dissimilar ferroic phases are an excellent alternative to single-phase multiferroics for a wide range of magnetoelectric technologies. In composites with strain-mediated magnetoelectric coupling the response is strongly dependent on the characteristics of the interface between the two mechanically coupled phases. Among the different material approaches considered, cofired ceramic composites offer improved reliability in applications and are more adequate for free-forming and miniaturization. However, their magnetoelectric response often suffers from poor reproducibility, which has been reiteratively associated with the quality of the interfaces with little experimental support. Here, we report an in-depth study of the local material properties across the interfaces of 0.36BiScO3-0.64PbTiO3/NiFe2O4 multilayer ceramic composites, processed by spark plasma sintering of nanocrystalline powders. Tailored microstructures and low residual stress levels were obtained by adjusting the sintering mismatch between the two ferroic phases, which also resulted in fully functional interfaces and enhanced magnetoelectric responses.
RESUMEN
In order to obtain a wide-range magnetoelectric (ME) response on a ME nanocomposite that matches industry requirements, Tb0.3Dy0.7Fe1.92 (Terfenol-D)/CoFe2O4/P(VDF-TrFE) flexible films were produced by the solvent casting technique and their morphologic, piezoelectric, magnetic and magnetoelectric properties were investigated. The obtained composites revealed a high piezoelectric response (≈-18 pC·N-1) that is independent of the weight ratio between the fillers. In turn, the magnetic properties of the composites were influenced by the composite composition. It was found that the magnetization saturation values decreased with the increasing CoFe2O4 content (from 18.5 to 13.3 emu·g-1) while the magnetization and coercive field values increased (from 3.7 to 5.5 emu·g-1 and from 355.7 to 1225.2 Oe, respectively) with the increasing CoFe2O4 content. Additionally, the films showed a wide-range dual-peak ME response at room temperature with the ME coefficient increasing with the weight content of Terfenol-D, from 18.6 to 42.3 mV·cm-1·Oe-1.
RESUMEN
There is a growing activity in the search of novel single-phase multiferroics that could finally provide distinctive magnetoelectric responses at room temperature, for they would enable a range of potentially disruptive technologies, making use of the ability of controlling polarization with a magnetic field or magnetism with an electric one (for example, voltage-tunable spintronic devices, uncooled magnetic sensors and the long-searched magnetoelectric memory). A very promising novel material concept could be to make use of phase-change phenomena at structural instabilities of a multiferroic state. Indeed, large phase-change magnetoelectric response has been anticipated by a first-principles investigation of the perovskite BiFeO3-BiCoO3 solid solution, specifically at its morphotropic phase boundary between multiferroic polymorphs of rhombohedral and tetragonal symmetries. Here, we report a novel perovskite oxide that belongs to the BiFeO3-BiMnO3-PbTiO3 ternary system, chemically designed to present such multiferroic phase boundary with enhanced ferroelectricity and canted ferromagnetism, which shows distinctive room-temperature magnetoelectric responses.
RESUMEN
A highly topical set of perovskite oxides are high-sensitivity piezoelectric ones, among which Pb(Zr,Ti)O3 at the morphotropic phase boundary (MPB) between ferroelectric rhombohedral and tetragonal polymorphic phases is reckoned a case study. Piezoelectric ceramics are used in a wide range of mature, electromechanical transduction technologies like piezoelectric sensors, actuators and ultrasound generation, to name only a few examples, and more recently for demonstrating novel applications like magnetoelectric composites. In this case, piezoelectric perovskites are combined with magnetostrictive materials to provide magnetoelectricity as a product property of the piezoelectricity and piezomagnetism of the component phases. Interfaces play a key issue, for they control the mechanical coupling between the piezoresponsive phases. We present here main results of our investigation on the suitability of the high sensitivity MPB piezoelectric perovskite BiScO3-PbTiO3 in combination with ferrimagnetic spinel oxides for magnetoelectric composites. Emphasis has been put on the processing at low temperature to control reactions and interdiffusion between the two oxides. The role of the grain size effects is extensively addressed.
RESUMEN
Thin film multiferroic nanocomposites might enable a range of potentially disruptive integrated magnetoelectric devices for information storage, spintronics, microwave telecommunications, and magnetic sensing. With this aim, we have investigated ion implantation of magnetic species into ferroelectric single crystal targets as a radically novel approach to prepare film nanoparticulate magnetic-metal ferroelectric-oxide composites. These materials are an alternative to multiferroic oxide epitaxial columnar nanostructures that are under intensive research, but whose magnetoelectric response is far from expectations. Here, we unambiguously demonstrate the preparation of such a thin film multiferroic nanocomposite of Co and BaTiO3 by ion implantation of a high dose of the magnetic species, followed by rapid thermal processing under tailored conditions. Results thus constitute a proof of concept for the feasibility of obtaining the materials by this alternative approach. Ion implantation is a standard technique for the microelectronic industry in combination with well-established patterning procedures.
RESUMEN
The relaxor-type behavior, electrical polarization buildup, and switching in 0.92Pb(Zn(1/3)Nb(2/3))O(3)-0.08PbTiO(3) nanostructured ceramics with a grain size of approximately 20 nm is reported for the first time. This composition presents the highest-known piezoelectric coefficients, yet phase stability is an issue. Ceramics can only be obtained by the combination of mechanosynthesis and spark-plasma sintering. The results raise the possibility of using nanoscale, perovskite-relaxor-based morphotropic-phase-boundary materials for sensing and actuation in nanoelectromechanical systems.
