Detection of Salt Content in Canned Tuna by Impedance Spectroscopy: A Feasibility Study for Distinguishing Salt Levels.

The electrical impedance of dilute aqueous solutions containing extracts from five brands of canned tuna is analyzed using impedance spectroscopy in order to analyze their salt content and detect the potential presence of other salts beyond the well-stated NaCl. A complex electrical impedance is modeled with an equivalent electrical circuit, demonstrating good agreement with experimental data. This circuit accounts for the contribution of ions in the bulk solution, as well as those contributing to electrode polarization. The parameters describing the equivalent circuits, obtained through fitting data to the electrical impedance, are discussed in terms of the various ion contributions to both the electrical double layer at the electrode interface and the electrical conductivity of each solution. The ionic contribution to the electrical impedance is compared with that of a pure NaCl solution at the same concentration range. This comparison, when extended to real samples, allows for the development of a model to estimate the electrical conductivity of canned tuna samples, thereby determining the salt concentration in tuna. The model enables differentiation among the various samples of tuna studied. Subsequently, the potential presence of other ions besides Na+ and Cl- and their contribution to the electrical properties of each canned tuna extract is considered, especially for samples with a higher ratio of the sum of K+ and phosphates to Na+ concentration. This analysis shows the potential of impedance spectroscopy for on-site and rapid analysis of salt content and/or detection of additives in canned tuna fish.

Active Thermochemical Barrier Coatings Using Metal Oxides: First Experimental Results.

A new concept of active thermal coating based on the use of reversible thermochemical reactions is presented in this paper. The new active thermal barrier coating uses redox reactions to buffer the temperature changes that a metallic component may suffer at high temperatures. The heat is stored when the temperature is equal/above the reduction temperature of the active coating (endothermic reaction) and the heat is released when the temperature is equal/below the oxidation temperature (exothermic reaction). The paper describes the development and testing of a reactive thermal barrier coating based on the redox reaction of Co3O4 and its cyclability. Co3O4 was chosen as a reference material due to the high enthalpy of reaction (844 kJ/kg) and redox reversibility. The activity of coatings with 1, 2, and 3 Co3O4 layers was demonstrated by simultaneous thermal analysis, showing good stability for 5 five cycles.

Study of the Effect of ZnO Functionalization on the Performance of a Fully Formulated Engine Oil.

The automotive sector is demanding higher specifications to achieve maximum efficiency; in this sense a new generation of lubricants with higher thermo-oxidative stability and superior tribological properties is being explored. The formulation of nanolubricants based on the nature of different nanomaterials is one of the most recent approaches, with several gaps to cover, such as dispersion stability, related to the compatibility of proposed nanomaterials with conventional additives and baseoils used in lubricant formulation. This study evaluated the effect of ZnO nanomaterial dispersed in a commercial engine oil using two different approaches; the use of surfactant and nanomaterial surface functionalization to promote higher stability and lower cluster size. Experimental evidence shows a synergetic effect between the tribological protection mechanism and the antioxidant properties in the lubricant. The effect of nanoparticle cluster size, functionalization level, and nanomaterial content are presented.

Flow Boiling Heat Transfer; Experimental Study of Hydrocarbon Based Nanorefrigerant in a Vertical Tube.

Flow boiling is a complex process but very efficient for thermal management in different sectors; enhancing flow boiling heat transfer properties is a research field of great interest. This study proposes the use of various nanomaterials, carbon-based materials, and metal oxides; in n-pentane as a hydrocarbon-based refrigerant to enhance the flow boiling heat transfer coefficient. This thermal property has been experimentally evaluated using a vertical evaporation device of glass with an internal diameter of 20 mm. The results have shown that proposed nanomaterials dispersion in n-pentane has a limited effect on the thermophysical properties and is conditioned by their dispersibility but promotes a significant increment of pentane heat transfer coefficient (h), increasing the overall heat transfer coefficient (U) of the evaporator. The enhanced heat transfer performance is attributed to the behavior of nanoparticles under working conditions and their interaction with the working surface, promoting a higher generation of nucleation sites. The observed behavior suggests a heat transfer mechanism transition from forced convection to nucleate heat transfer, supported by visual observations.

Systematic Approach to the Synthesis of Cobalt-Containing Polyoxometalates for Their Application as Energy Storage Materials.

New energy storage materials are an object of study within the framework of the global energy transition. The development of renewable sources is being boosted thanks to stationary energy storage systems such as redox flow batteries (RFBs). This work reports the synthesis of the cobalt-containing Keggin-type polyoxometalates [CoW12O40]6- (CoW12) and [Co(H2O)SiW11O39]6- (CoSiW11), which have previously been shown to have applicability in RFBs. These procedures were reassessed to meet the strict requirements associated with the further implementation of RFBs, including fast and affordable synthetic procedures with high reaction yields. In contrast to the lengthy and complicated synthetic approaches published to date, the optimized synthesis reported in this work enables the isolation of the pure crystalline salt of the CoW12 anion with a 75% reduction of the time of the whole reaction procedure, eliminating tedious steps such as the recrystallization and including a 20% increased yield. The control of the stoichiometry, fine-tuning of reaction conditions, and the identification of intermediate species, as well as the acidic equilibria taking place during the process, were monitored via thermal, spectroscopic, and structural analyses. In the case of the CoSiW11 anion, its preparation was based on a simple and highly efficient procedure. Moreover, promising electrochemical properties were observed with the use of the one-pot synthetic approach, in which the stoichiometric amounts of the starting reagents are dissolved in the supporting electrolyte to be directly implemented as the electrolyte for a RFB.

A Review on Sustainable Inks for Printed Electronics: Materials for Conductive, Dielectric and Piezoelectric Sustainable Inks.

In the last decades, the demand for electronics and, therefore, electronic waste, has increased. To reduce this electronic waste and the impact of this sector on the environment, it is necessary to develop biodegradable systems using naturally produced materials with low impact on the environment or systems that can degrade in a certain period. One way to manufacture these types of systems is by using printed electronics because the inks and the substrates used are sustainable. Printed electronics involve different methods of deposition, such as screen printing or inkjet printing. Depending on the method of deposition selected, the developed inks should have different properties, such as viscosity or solid content. To produce sustainable inks, it is necessary to ensure that most of the materials used in the formulation are biobased, biodegradable, or not considered critical raw materials. In this review, different inks for inkjet printing or screen printing that are considered sustainable, and the materials that can be used to formulate them, are collected. Printed electronics need inks with different functionalities, which can be mainly classified into three groups: conductive, dielectric, or piezoelectric inks. Materials need to be selected depending on the ink's final purpose. For example, functional materials such as carbon or biobased silver should be used to secure the conductivity of an ink, a material with dielectric properties could be used to develop a dielectric ink, or materials that present piezoelectric properties could be mixed with different binders to develop a piezoelectric ink. A good combination of all the components selected must be achieved to ensure the proper features of each ink.

Development of a Kinetic Model for the Redox Reactions of Co2.4Ni0.6O4 and SiO2/Co2.4Ni0.6O4 Oxides for Thermochemical Energy Storage.

One of the possible solutions for the transition of the actual energetic model is the use of thermal energy storage technologies. Among them, thermochemical energy storage based on redox reactions involving metal oxides is very promising due to its high energy density. This paper deals with the development of the kinetic study based on data extracted from the thermogravimetric analysis of a cobalt-nickel mixed oxide (Co2.4Ni0.6O4) without and with the addition of SiO2 particles to improve the cyclability. The results show that in the reduction reaction the activation energy is not affected by the addition of SiO2 particles while in the oxidation reaction an increase in the activation energy is observed. The theoretical models fitting with the experimental data are different for each material in the reduction reaction. The mixed oxide is controlled by a nucleation and growth mechanism for conversion ratios higher than 0.5, while the added material is controlled by diffusion mechanisms. In the oxidation reaction, the two materials are controlled by a nucleation and growth mechanism for conversion ratios higher than 0.5.

Energetic study of ultrasonic wettability enhancement.

Many industrial and biological interfacial processes, such as welding and breathing depend directly on wettability and surface tension phenomena. The most common methods to control the wettability are based on modifying the properties of the fluid or the substrate. The present work focuses on the use of high-frequency acoustic waves (ultrasound) for the same purpose. It is well known that ultrasound can effectively clean a surface by acoustic cavitation, hence ultrasonic cleaning technology. Besides the cleaning process itself, many authors have observed an important wettability enhancement when liquids are exposed to low and high (ultrasonic) frequency vibration. Ultrasound goes one step further as it can instantly adjust the contact angle by tuning the vibration amplitude, but there is still a lack of comprehension about the physical principles that explain this phenomenon. To shed light on it, a thermodynamic model describing how ultrasound decreases the contact angle in a three-phase wetting system has been developed. Moreover, an analytical and experimental research has been carried out in order to demonstrate that ultrasound is an important competitor to surfactants in terms of energy efficiency and environmental friendliness.

Thermal and Photocatalytic Performance of Unsaturated Polyester Resins Modified with TiO2 Nanoparticles as Panel Bodies for Vehicles.

The transport sector is the fastest growing contributor to climate emissions and experiences the highest growth in energy use. This study explores the use of TiO2 nanoparticles for obtaining photocatalytic nanocomposites with improved infrared reflectance properties. The nanocomposites were prepared by dispersing 0-20 wt% of TiO2 nanoparticles in an unsaturated polyester resin. The effect of TiO2 on the curing kinetics was studied by differential scanning calorimetry, showing a significant delay of the curing reactions. The thermal reflectance of the modified resins was characterized by UV-Vis-NIR spectrophotometry, measuring total solar reflectance (TSR). The TiO2 greatly increased the TSR of the resin, due to the reflectance properties of the nanoparticles and the change in color of the modified resin. These nanocomposites reflect a significant part of near-infrared radiation, which can contribute to a reduction of the use of heating, ventilation, and air conditioning. Moreover, the photocatalytic effect of the TiO2 modified nanocomposites was studied by monitoring the degradation of an organic model contaminant in an aqueous medium under UV light, and the reusability of the nanocomposites was studied with 5 cycles. The developed nanocomposites are proposed as a solution for reducing global warming and pollutant emissions.

Porous TiO2 thin film-based photocatalytic windows for an enhanced operation of optofluidic microreactors in CO2 conversion.

Using a photocatalytic window can simplify the design of an optofluidic microreactor, providing also a more straightforward operation. Therefore, the development of TiO2 coatings on glass substrates seems appealing, although a priori they would imply a reduced accessible area compared with supported nanoparticle systems. Considering this potential drawback, we have developed an endurable photocatalytic window consisting on an inner protective SiO2 layer and an outer mesoporous anatase layer with enhanced surface area and nanoscopic crystallite size (9-16 nm) supported on a glass substrate. The designed photocatalytic windows are active in the CO2-to-methanol photocatalytic transformation, with maximum methanol yield (0.52 µmol·h-1·cm-2) for greatest porosity values and minimum crystallite size. Compared with benchmark supported nanoparticle systems, the nanoscopic thickness of the coatings allowed to save photoactive material using only 11-22 µg·cm-2, while its robustness prevented the leaching of active material, thus avoiding the decay of performance at long working periods.

Novel Antibacterial and Toughened Carbon-Fibre/Epoxy Composites by the Incorporation of TiO2 Nanoparticles Modified Electrospun Nanofibre Veils.

The inclusion of electrospun nanofiber veils was revealed as an effective method for enhancing the mechanical properties of fiber-reinforced epoxy resin composites. These veils will eventually allow the incorporation of nanomaterials not only for mechanical reinforcement but also in multifunctional applications. Therefore, this paper investigates the effect of electrospun nanofibrous veils made of polyamide 6 modified with TiO2 nanoparticles on the mechanical properties of a carbon-fiber/epoxy composite. The nanofibers were included in the carbon-fiber/epoxy composite as a single structure. The effect of positioning these veils in different composite positions was investigated. Compared to the reference, the use of unmodified and TiO2 modified veils increased the flexural stress at failure and the fracture toughness of composites. When TiO2 modified veils were incorporated, new antibacterial properties were achieved due to the photocatalytic properties of the veils, widening the application area of these composites.

TiO2-Doped Electrospun Nanofibrous Membrane for Photocatalytic Water Treatment.

This work has been focused on the one-step fabrication by electrospinning of polyamide 6 (PA6) nanofibre membranes modified with titanium dioxide nanoparticles (TiO2), where these TiO2 nanoparticles aggregates could induce a photocatalytic activity. The main potential application of these membranes could be the purification of contaminated water. Thus, it is important to analyse the contaminant degradation capability since in these membranes this is based on their photocatalytic activity. In this work, the effect of the photocatalysis has been studied both on the degradation of an organic model contaminant and on the removal of Escherichia coli and other coliform bacteria. As a result, it was observed that these membranes present excellent photocatalytic activity when they are irradiated under UV light, allowing a 70% reduction of an organic model pollutant after 240 min. In addition, these membranes successfully removed Escherichia coli and other coliform bacteria in artificially inoculated water after 24 h of contact with them. Moreover, the stand-alone structure of the membranes allowed for the reusing of the immobilized catalyst. The experimental evidence indicated that developed nanofibre membranes are a fast and efficient solution for polluted water decontamination based on photocatalysis. Their use could contribute to guarantee a fresh water level and quality, mitigating the water scarcity problem worldwide.

Effect of Different Types of Electrospun Polyamide 6 Nanofibres on the Mechanical Properties of Carbon Fibre/Epoxy Composites.

Delamination and brittle matrix fracture have long since been the biggest problems in fibre-reinforced composites. Recently, the incorporation of electrospun nanofibre veils has been shown to be an effective method for improving the mechanical properties of these composites, without causing process problems and negatively affecting other mechanical properties. Thus, these nanofibres have the potential to be used as thickness-reinforcing materials in composites. This paper investigates the effect of incorporating standalone electrospun nanofibre veils made of two different types of polyamide 6 (PA6) on the mechanical properties of carbon fibre/epoxy composites. The influence of positioning the electrospun veils at different interlaminar positions of the laminate has also been investigated.

Effects of Graphene Oxide and Chemically-Reduced Graphene Oxide on the Dynamic Mechanical Properties of Epoxy Amine Composites.

Composites based on epoxy/graphene oxide (GO) and epoxy/reduced graphene oxide (rGO) were investigated for thermal-mechanical performance focusing on the effects of the chemical groups present on nanoadditive-enhanced surfaces. GO and rGO obtained in the present study have been characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and X-ray powder diffraction (XRD) demonstrating that materials with different oxidation degrees have been obtained. Thereafter, GO/epoxy and rGO/epoxy nanocomposites were successfully prepared and thoroughly characterized by dynamic mechanical thermal analysis (DMTA) and transmission electron microscopy (TEM). A significant increase in the glass transition temperature was found in comparison with the neat epoxy. The presence of functional groups on the graphene surface leads to chemical interactions between these functional groups on GO and rGO surfaces with the epoxy, contributing to the possible formation of covalent bonds between GO and rGO with the matrix. The presence of oxidation groups on GO also contributes to an improved exfoliation, intercalation, and distribution of the GO sheets in the composites with respect to the rGO based composites.

Low-cost visible-near infrared sensor for on-line monitoring of fat and fatty acids content during the manufacturing process of the milk.

This paper describes the calibration, validation and testing process of a low-cost on-line visible-near infrared (400-1100 nm) sensor for the monitoring of fat and fatty acids content in milk during the manufacturing process of milk. The optical, mechanical and electronic designs of the sensor have been developed in Tekniker IK4 research centre just as its manufacturing process. The measurement range of the sensor is 400-1100 nm thus it covers the visible range (400-780 nm) and the short-wave near infrared (780-1100 nm). Chemometric techniques were applied with the purpose of obtaining a predictive model for each parameter correlating the spectra obtained by the sensor with the parameters analysed in the laboratory. The models were developed by Partial Least Squares Regression (PLS) obtaining one model for each parameter. The raw milk samples used in this work were provided by CAPSA (Asturias, Spain).