Combining high energy ball milling and liquid crystal templating method to prepare magnetic ordered mesoporous silica. A physico-chemical investigation.

The physico-chemical investigation of superparamagnetic MCM41 like materials prepared by the novel combination of high energy ball milling and a liquid crystal templating method is presented. Structural, morphological, textural, thermal, and preliminary magnetic characterization demonstrated the successful combination of the two synthesis techniques, avoiding the problems associated with the current methods used for the preparation of magnetic ordered mesoporous silica. MCM41 like materials with high specific surface area values (625-720 m2 g-1) and high mesopore volumes in the range 1-0.7 cm3 g-1 were obtained. The ordered mesoporous structure and accessible pores were maintained after the inclusion of increasing amounts of the magnetic component in the silica structure. All the samples showed superparamagnetic behaviour.

N-Alkylation of aromatic amines with alcohols by using a commercially available Ru complex under mild conditions.

An N-alkylation procedure has been developed under very mild conditions using a known commercially available Ru-based catalyst. As a result, a wide range of aromatic primary amines has been selectively alkylated with several primary alcohols, yielding the corresponding secondary amines in high yields. The methodology also enables the methylation of anilines in refluxing methanol and the preparation of a set of heterocycles in a straightforward way.

Aluminosilicate-Supported Catalysts for the Synthesis of Cyclic Carbonates by Reaction of CO2 with the Corresponding Epoxides.

Functionalized aluminosilicate materials were studied as catalysts for the conversion of different cyclic carbonates to the corresponding epoxides by the addition of CO2. Aluminum was incorporated in the mesostructured SBA-15 silica network. Thereafter, functionalization with imidazolium chloride or magnesium oxide was performed on the Al_SBA-15 supports. The isomorphic substitution of Si with Al and the resulting acidity of the supports were investigated via 27Al magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy and NH3 adsorption microcalorimetry. The Al content and the amount of MgO were quantified via inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis. The anchoring of the imidazolium salt was assessed by 29Si and 13C MAS NMR spectroscopy and quantified by combustion chemical analysis. Textural and structural properties of supports and catalysts were studied by N2 physisorption and X-ray diffraction (XRD). The functionalized systems were then tested as catalysts for the conversion of CO2 and epoxides to cyclic carbonates in a batch reactor at 100 or 125 °C, with an initial CO2 pressure (at room temperature) of 25 bar. Whereas the activity of the MgO/xAl_SBA-15 systems was moderate for the conversion of glycidol to the corresponding cyclic carbonate, the Al_SBA-15-supported imidazolium chloride catalysts gave excellent results over different epoxides (conversion of glycidol, epichlorohydrin, and styrene oxide up to 89%, 78%, and 18%, respectively). Reusability tests were also performed. Even when some deactivation from one run to the other was observed, a comparison with the literature showed the Al-containing imidazolium systems to be promising catalysts. The fully heterogeneous nature of the present catalysts, where the inorganic support on which the imidazolium species are immobilized also contains the Lewis acid sites, gives them a further advantage with respect to most of the catalytic systems reported in the literature so far.

Synthesis of Dimethyl Carbonate by Transesterification of Propylene Carbonate with Methanol on CeO2-La2O3 Oxides Prepared by the Soft Template Method.

In this study, CeO2, La2O3, and CeO2-La2O3 mixed oxide catalysts with different Ce/La molar ratios were prepared by the soft template method and characterized by different techniques, including inductively coupled plasma atomic emission spectrometry, X-ray diffraction, N2 physisorption, thermogravimetric analysis, and Raman and Fourier transform infrared spectroscopies. NH3 and CO2 adsorption microcalorimetry was also used for assessing the acid and base surface properties, respectively. The behavior of the oxides as catalysts for the dimethyl carbonate synthesis by the transesterification of propylene carbonate with methanol, at 160 °C under autogenic pressure, was studied in a stainless-steel batch reactor. The activity of the catalysts was found to increase with an increase in the basic sites density. The formation of dimethyl carbonate was favored on medium-strength and weak basic sites, while it underwent decomposition on the strong ones. Several parasitic reactions occurred during the transformation of propylene carbonate, depending on the basic and acidic features of the catalysts. A reaction pathway has been proposed on the basis of the components identified in the reaction mixture.

Nanostructured Ni/CeO2-ZrO2 Catalysts for CO2 Conversion into Synthetic Natural Gas.

NiO-CeO2-ZrO2 mixed oxides, with Ni/(Ce + Zr) = 1 mol/mol and different Ce/Zr molar ratios, were prepared by the soft-template method. The chemical composition, texture, structure, and redox features of the synthesized systems were investigated by different techniques. All samples were nanocrystalline (NiO nanocrystal average size 4 nm) and had high surface area and quite an ordered mesoporous system. The catalytic performances in the CO2 conversion into methane were studied at atmospheric pressure, 300 °C, and stoichiometric H2/CO2 molar ratio. Prior to reaction the catalysts were submitted to a mild reduction pretreatment (H2 at 400 °C for 1 h). XRD analysis of the samples after pretreatment showed the presence of small Ni crystals (4-7 nm) on all the samples as well as of some unreduced NiO nanocrystals on the systems with high Zr content, in accordance with H2-TPR experiments, which indicated that NiO reduction is promoted by CeO2 but hindered by ZrO2. The catalytic tests were performed at two different space velocities (72000 and 900000 cm³ h-1 g-1cat) on a series of Ni-based catalysts supported on CeO2-ZrO2 systems with different Ce/Zr ratios, including the two pure oxides. CO2 conversion and selectivity to CH4 (which was always close to 100 mol%) were constant throughout the 6-hour runs. CO2 conversion resulted to increase with CeO2 content in the catalyst, thus indicating the role of the CeO2 component of the support in activating CO2, whereas H2 is activated on the Ni nanoparticles.

Bi-functional heterogeneous catalysts for carbon dioxide conversion: enhanced performances at low temperature.

Novel heterogeneous bi-functional catalysts bearing tin or zinc inserted as single sites within the silica architecture acting as acid centres and decorated with imidazolium moieties as the nucleophile source were successfully synthesized. The materials were extensively characterized via various techniques including N2 physisorption, solid state nuclear magnetic resonance, X-ray photoelectron spectroscopy, transmission electron microscopy and adsorption microcalorimetry. The solids were tested as catalysts for the conversion of carbon dioxide, selecting the synthesis of styrene carbonate as the target reaction. Both materials exhibited improved performances compared to the analogous solids functionalized with the sole imidazolium salt as well as to other materials reported in the literature. The Sn-based catalyst displayed excellent conversion also in the presence of various epoxides. In all experiments the bi-functional solid allowed reducing the reaction temperature below 150 °C. In the presence of glycidol the temperature was decreased down to 30 °C. The short synthesis protocol of the heterogeneous catalysts, together with the 100% atom economy of the target reaction and the low reaction temperature, make the entire process highly sustainable. Moreover, the Sn-based catalyst was stable under the selected reaction conditions and reusable for multiple catalytic cycles.