RESUMEN
In an effort to tackle the skin reactions frequently observed with topical application of ivermectin (IVM), a study was conducted to develop and optimize transethosomes (TESMs) loaded with IVM for scabies treatment. A three-factor, two-level (23) full factorial design was employed. Soyabean phosphatidylcholine concentration (A), ethanol concentration (B) and Span 60 amount (C) were studied as independent factors, while entrapment efficiency (EE), particle size (PS), polydispersity index (PDI), zeta potential (ZP) and drug release after 6 h (Q6h) were characterized. The skin sensitivity of the optimized formulation was evaluated by skin irritation test and histopathological examination. The EE% ranged from 88.55 ± 0.576% to 94.13 ± 0.305%, PS was from 318.033 ± 45.61 nm to 561.400 ± 45.17 nm, PDI was from 0.328 ± 0.139 to 0.671 ± 0.103, ZP was from -54.13 ± 1.09 mV to -60.50 ± 2.34 mV and Q6h was from 66.20 ± 0.30% to 93.46 ± 0.86%. The IVM-loaded transethosomal cream showed lower skin irritation and a more intact epidermal layer with intact keratinocyte, compared to the marketed cream which showed severe destruction of the keratin layer. Therefore, patient compliance can be improved by encapsulating IVM within TESMs to minimize its skin reactions.
RESUMEN
High percentage of diabetic people are diagnosed as type 2 who require daily dosing of an antidiabetic drug such as Linagliptin (Lina) to manage their blood glucose levels. This study aimed to develop injectable Lina-loaded biodegradable poly (lactic-co-glycolic acid) (PLGA) in-situ implants (ISIs) to deliver a desired burst effect of Lina followed by a sustained release over several days for controlling the blood glucose levels over prolonged time periods. The morphological, pharmacokinetic, and pharmacodynamic assessments of the Lina-loaded ISIs were performed. Scanning electron microscopy (SEM) study revealed the rapid exchange between the water miscible solvent (N-methyl-2-pyrrolidone; NMP) and water during the ISI preparation, hence enhancing the initial burst Lina release. While, triacetin of lower water affinity could lead to formation of more compact and dense ISI structure with slower drug release. By comparing various ISI formulations containing different solvents and different PLGA concentrations, the ISI containing 40 % PLGA and triacetin was selected for its sustained release of Lina (93.06 ± 1.50 %) after 21 days. The pharmacokinetic results showed prolonged half life (t1/2) and higher area under the curve (AUC) values of the selected Lina-loaded ISI when compared to those of oral Lina preparation. The single Lina-ISI injection produced a hypoglycemic control in the diabetic rats very similar to the daily oral administration of Lina after 7 and 14 days. In conclusion, PLGA-based ISIs confirmed their suitability for prolonging Lina release in patients receiving long-term antidiabetic therapy, thereby achieving more enhanced patient compliance and reduced dosing frequency.
RESUMEN
The aim of the study was to design injectable long-acting poly (lactide-co-glycolide) (PLGA)-based in situ gel implants (ISGI) loaded with the anti-diabetic alogliptin. Providing sustained therapeutic exposures and improving the pharmacological responses of alogliptin were targeted for achieving reduced dosing frequency and enhanced treatment outputs. In the preliminary study, physicochemical characteristics of different solvents utilized in ISGI preparation were studied to select a proper solvent possessing satisfactory solubilization capacity, viscosity, water miscibility, and affinity to PLGA. Further, an optimization technique using a 23 factorial design was followed. The blood glucose levels of diabetic rats after a single injection with the optimized formulation were compared with those who received daily oral alogliptin. N-methyl-2-pyrrolidone (NMP) and dimethyl sulfoxide (DMSO), as highly water-miscible and low viscous solvents, demonstrated their effectiveness in successful ISGI preparation and controlling the burst alogliptin release. The impact of increasing lactide concentration and PLGA amount on reducing the burst and cumulative alogliptin release was represented. The optimized formulation comprising 312.5 mg of PLGA (65:35) and DMSO manifested a remarkable decrease in the rats' blood glucose levels throughout the study period in comparison to that of oral alogliptin solution. Meanwhile, long-acting alogliptin-loaded ISGI systems demonstrated their feasibility for treating type 2 diabetes with frequent dosage reduction and patient compliance enhancement.
RESUMEN
Irritable bowel syndrome (IBS); a widespread disorder in gastrointestinal tract especially in children, burdens their healthcare systems and upsets families. Great attention was paid to understand the pathophysiological cause of disorder. However, developing a convenient treatment especially for children remains a challenge. Phosphodiesterase inhibitors were recently introduced for IBS management. Vardenafil (VDF), a phosphodiesterase-5 inhibitor, exhibiting limited bioavailability when taken orally due to extensive first-pass effect, was the choice for study. This study aimed to formulate VDF jellies as a buccal dosage form to improve pediatric compliance and achieve maximum drug efficacy. VDF oral jellies were prepared by heat and congeal method, and were evaluated for their pH, content uniformity, physical stability, general appearance, and in-vitro drug release. VDF jellies (F1), with satisfactory organoleptic properties and highest percent of drug released compared to other formulations was selected as a master formula for further study to ensure in-vivo efficacy. cyclic Guanosine Mono Phosphate (cGMP), used as indicator of VDF concentration in blood, was highly increased after administration of VDF jellies (F1), compared to oral VDF suspension. Increased defecation with improved fecal consistency strongly favored oral jellies as a potential alternative route for VDF for IBS management with high pediatric acceptance.
RESUMEN
For patient convenience, sustained release Adefovir Poly-d,l-lactic-co-glycolic acid (PLGA) microspheres were formulated to relieve the daily use of the drug which is a problem for patients treated from chronic hepatitis-B. PLGA microspheres were prepared and characterized by entrapment efficiency, particle size distribution and scanning electron microscopy (SEM). In-vitro release and in-vivo studies were carried out. Factors such as drug: polymer ratio, polymer viscosity and polymer lactide content were found to be important variables for the preparation of PLGA Adefovir microspheres. Fourier transform infrared (FTIR) analysis and differential scanning calorimetry (DSC) were performed to determine any drug-polymer interactions. One way analysis of variance (ANOVA) was employed to analyze the pharmacokinetic parameters after intramuscular injection of the pure drug and the selected PLGA microspheres into rats. FTIR and DSC revealed a significant interaction between the drug and the polymer. Reports of SEM before and after 1 and 24â¯h release showed that the microspheres had nonporous smooth surface even after 24â¯h release. The entrapment efficiency ranged between 55.83 and 86.95% and in-vitro release studies were continued for 16, 31 and 90â¯days. The pharmacokinetic parameters and statistical analysis showed a significant increase in the Tmax, AUC0-t and MRT, and a significant decrease in the Cmax of the tested formulation (pâ¯<â¯0.05). Results demonstrated that PLGA Adefovir microspheres could be used for long-term treatment of chronic hepatitis-B instead of the daily dose used by the patient.