RESUMEN
The development and optimization of holographic materials represent a great challenge today. These materials must be synthesized according to the characteristics that are desirable in photonic devices whose application is the object of investigation. In certain holographic sensors and biosensors, it is essential that the recording material be stable in liquid media. Furthermore, the holographic gratings stored in them must have temporal and structural stability, so that they can act as transducers of the analytical signal. Therefore, it is essential to optimize its storage in terms of the chemical composition of the material and the optical parameters of recording. This work focuses on the study of the storage optimization of unslanted transmission volume phase holograms in photohydrogels based on acrylamide and N,N'-methylenebis(acrylamide). Hydrogel matrices, also composed of acrylamide and N,N'-methylenebis(acrylamide), with different degrees of cross-linking were used and analyzed by scanning electron microscopy and UV-visible spectroscopy. The best results in terms of diffraction efficiency were reached for hydrogel matrices with an acrylamide/N,N'-methylenebis(acrylamide) molar ratio between 19.9 and 26. This relationship was also optimized in the incubator solution used to incorporate the components necessary for the formation of the holograms in the hydrogel matrices. The maximum diffraction efficiency, about 35%, was achieved when using an incubation solution with an acrylamide/N,N'-methylenebis(acrylamide) molar ratio of 4.35. The influence of the physical thickness of the hydrogel layers, the intensity, and the exposure time on the diffraction efficiency was also investigated and optimized. In addition, the behavior of the hologram was analyzed after a washing stage with PBST. A simple model that considered the effects of bending and attenuation of holographic gratings was proposed and used to obtain the optical parameters of the holograms.
RESUMEN
We print a tunable photopolymer (photopolymer dispersed liquid crystal -PDLC), using the laser-induced direct transfer technique without absorber layer, which was a challenge for this technique given the low absorption and high viscosity of PDLC, and which had not been achieved so far to our knowledge. This makes the LIFT printing process faster and cleaner and achieves a high-quality printed droplet (aspheric profile and low roughness). A femtosecond laser was needed to reach sufficiently peak energies to induce nonlinear absorption and eject the polymer onto a substrate. Only a narrow energy window allows the material to be ejected without spattering.
RESUMEN
The similarity between object and image of negative asymmetrical holographic lenses (HLs) stored in a low-toxicity photopolymer has been evaluated theoretically and experimentally. Asymmetrical experimental setups with negative focal lengths have been used to obtain HLs. For this purpose, the resolution of the HLs was calculated using the convolution theorem. A USAF 1951 test was used as an object and the impulse responses of the HLs, which in this case was the amplitude spread function (ASF), were obtained with two different methods: using a CCD sensor and a Hartmann Shack (HS) wavefront sensor. For a negative asymmetrically recorded HL a maximum resolution of 11.31 lp/mm was obtained. It was evaluated at 473 nm wavelength. A theoretical study of object-image similarity had carried out using the MSE (mean squared error) metric to evaluate the experimental results obtained quantitatively.
RESUMEN
A low-toxicity photopolymer was employed to prepare holographic solar concentrators (HSCs). The main aim of this study is to obtain a versatile holographic element to concentrate the sunlight from different relative positions of the Sun during the day, avoiding the need of expensive tracking systems. Multiplexed holographic elements that combine symmetric and asymmetric holographic lenses of low frequency (545 l/mm) have been recorded in the same plate to concentrate the sunlight from sunrise to sunset. The holographic behavior of HSCs has been studied by measuring the angular diffraction efficiency at 633 nm (close to the maximum response of silicon cells). The efficiency of the complete system "HSC-solar cell" has been evaluated by measuring the short-circuit current (Isc) under solar illumination at different incident angles. This study overcomes the trade-off between good efficiency and high incident acceptance angle, showing an important breakthrough to obtain wide acceptance angle systems.
RESUMEN
The storage of time-stable holographic gratings in hydrogel matrices when the material is immersed in aqueous media is a real challenge at present. The optimization of the storage stages of the holograms must be properly investigated to identify the most suitable development processes. For this reason, this work is focused on the study of the optimization of the washing stages of the hydrogels based on acrylamide and N,N'-methylenebis(acrylamide) once unslanted transmission holograms have been stored. High-performance liquid chromatography and UV-visible measurements have been employed in our system to analyze the composition of the washing solutions. PBST and DMSO:H2O are used as solvents in the washing stages. The diffraction efficiencies are measured during the washing stages and after the storing of the holograms during several days in PBST. Maximum diffraction efficiencies of 38 and 27.6% are reached when PBST and DMSO:H2O are employed, respectively, for the washing process. Holograms show temporal stability after being stored immersed in PBST at 4 °C for 4 days.
RESUMEN
Diffraction gratings are recorded in a holographic photopolymer containing nematic liquid crystal and peppermint oil. The presence of the oil modifies the polymerization and the holographic response. The composite containing oil adulterated with triethyl citrate obtains a diffraction efficiency related to the oil's purity. The results obtained suggest the possibility of developing a holographic chemical analysis method for quality control of raw materials.
RESUMEN
Precise characterization of parallel-aligned liquid crystal on silicon microdisplays has an important impact in many advanced photonics applications. We show liquid crystal on silicon (LCoS) modeled as a non-absorbent reciprocal device. Combined with time-average Stokes polarimetry, LCoS enables us to demonstrate robust measurements across the whole applied voltage range for the retardance and its flicker, and also as a novelty for the director orientation. We obtain that the director orientation changes across the voltage range, especially at larger applied voltages. This is a small effect, but it may provide a deeper insight into the internal dynamics in the liquid crystal layer, and in sensitive phase-only applications will produce a coupling between amplitude and phase.
RESUMEN
Photopolymers can be used to fabricate different holographic optical elements, although maximization of the phase-shift in photopolymers has been a challenge for the last few decades. Different material compositions and irradiation conditions have been studied in order to achieve it. One of the main conclusions has been that with continuous laser exposure better results are achieved. However, our results show for the first time that higher phase-shift can be achieved using a pulsed laser. The study has been conducted with crosslinked acrylamide-based photopolymers exposed with a pulsed laser (532 nm). The increment of the phase-shift between the pulsed laser and continuous laser exposure is 17%, achieving a maximum phase-shift of 3π radians and a refractive index shift of 0.0084 at the zero spatial frequency limit, where monomer diffusion does not take place. This allows this photopolymer to be used in large-scale manufacturing.
RESUMEN
This work presents recent results derived from the rigorous modelling of holographic polymer-dispersed liquid crystal (H-PDLC) gratings. More precisely, the diffractive properties of transmission gratings are the focus of this research. This work extends previous analysis performed by the authors but includes new features and approaches. More precisely, full 3D numerical modelling was carried out in all analyses. Each H-PDLC sample was generated randomly by a set of ellipsoid geometry-based LC droplets. The liquid crystal (LC) director inside each droplet was computed by the minimisation of the Frank elastic free energy as a function of the applied electric field. The analysis carried out considered the effects of Frank elastic constants K11, K22 and K33; the anchoring strength W0; and even the saddle-splay constant K24. The external electric field induced an orientation of the LC director, modifying the optical anisotropy of the optical media. This effect was analysed using the 3D split-field finite-difference time-domain (SF-FDTD) method. In order to reduce the computational costs due to a full 3D tensorial analysis, a highly optimised method for high-performance computing solutions (HPC) was developed. The influences of the anchoring and voltage on the diffraction efficiencies were investigated, showing the potential of this approach.
RESUMEN
In this work, we study the imaging characteristics of an optical see-through display based on a holographic waveguide. To fabricate this device, two transmission holograms are recorded on a photopolymer material attached to a glass substrate. The role of the holograms is to couple the incident light between air and the glass substrate, accomplishing total internal reflection. The role of noise reflection gratings and shrinkage on the imaging characteristics of the device will be also explored. The holograms (slanted transmission gratings with a spatial frequency of 1690 lines/mm) were recorded on a polyvinyl alcohol acrylamide holographic polymer dispersed liquid crystal (HPDLC) material. We will show that sufficient refractive index modulation is achieved in the material, in order to obtain high diffraction efficiencies. We will demonstrate that the final device acts as an image formation system.
RESUMEN
Aberrations and the image quality of holographic lenses were evaluated by a Hartmann-Shack (HS) wavefront sensor. Two lenses, one recorded with a symmetrical configuration and the other with an asymmetrical one, were stored in a photopolymer called Biophotopol. Each was reconstructed with two different wavelengths, 473 nm and 633 nm. Different metrics were applied to determine and quantify the aberration of the lenses (Zernike coefficients, Seidel coefficients, Marechal tolerances, root-mean-square (RMS), peak to valley, critical fraction of the pupil), and the quality of the image they provided (Strehl ratio, entropy, cutoff frequency, modulation transfer function (MTF), and area under the MTF). Good agreement between the metrics related to optical quality was obtained. The negative asymmetric holographic lenses had less aberration than the positive symmetric ones.
RESUMEN
We study the recording of complex diffractive elements, such as achromatic lenses, fork gratings or axicons. Using a 3-D diffusion model, previously validated, we are able to predict the behavior of photopolymer during recording. The experimental recording of these complex elements is possible thanks to a new generation spatial light modulator capable of generating periodic and aperiodic profiles. Both experimental and theoretical are analyzed and compared. The results show not only the good response of theoretical model to predict the behavior of the materials, but also the viability of photopolymers to store these kind of elements.
RESUMEN
Tert-Butylthiol (TBT) and tetrahydrothiophene (THT) are odorant substances added to natural gas and liquefied petroleum gas to help their detection by the human smell. In this research, TBT and THT are incorporated into a holographic polymer-dispersed liquid crystal and their influence in the main holographic characteristics of the photopolymer are studied in order to open the way towards the design of a holographic sensor to detect natural gas and liquefied petroleum gas.
RESUMEN
A holographic polymer dispersed liquid crystal (HPDLC) is used to record holographic diffraction gratings. Several mixtures of nematic liquid crystals (LC) are used as components of the HPDLC to evaluate their influence in static and dynamic basic properties. The diffraction efficiency obtained in the reconstruction of the holograms is evaluated to compare the influence of the different LC. Additionally, the samples are exposed to a variable electric field and the diffracted light intensity as a function of the applied voltage is measured to evaluate the influence of the LC. The results obtained show significant differences depending on the LC incorporated to the photopolymer.
RESUMEN
We demonstrate a complete semiphysical and analytical model describing the angular and wavelength dependencies not only of retardance, but also its flicker, in parallel aligned liquid crystal (PA-LC) devices. It relies on the fitting of the molecules' equivalent tilt angle as a function of applied voltage. The wide range of calculations it offers without requiring extensive characterization makes the model unique. We focus on PA-LCoS application as a polarization state generator across the visible spectrum and for a wide range of incidence angles. This approach offers novel capabilities for managing arbitrary states of both full and partial polarization. To highlight the richness of situations with PA-LCoS devices, we provide results for two different digital addressing sequences producing different levels of flicker.
RESUMEN
In recent works, we demonstrated the accuracy and physical relevance of a highly simplified reverse-engineering analytical model for a parallel-aligned liquid crystal on silicon devices (PA-LCoS). Both experimental measurements and computational simulations applying the rigorous split-field finite difference time domain (SF-FDTD) technique led to this conclusion in the low applied voltages range. In this paper, we develop a complete rigorous validation covering the full range of possible applied voltages, including highly non-linear liquid crystal (LC) tilt angle profiles. We demonstrate the applicability of the model for spectral and angular retardation calculations, of interest in spatial light modulation applications. We also show that our analytical model enables the calculation of the retardance for novel PA-LC devices as a function of the LC compound and cell gap, becoming an appealing alternative to the usual numerical approaches for PA-LC devices design.
RESUMEN
In this paper, we theoretically and experimentally evaluated the quality of volume phase transmission lenses stored in an environmentally friendly photopolymer. Holographic lenses (HLs) were obtained using symmetrical and asymmetrical experimental setups with the same positive and negative focal length and pupil diameter. The image quality was evaluated from the calculation of the modulation transfer function (MTF) by capturing the point spread function (PSF) with a charge-coupled device (CCD). A maximum frequency of 14 L/mm, reaching an MTF value of 0.1, was obtained for a negative asymmetrically recorded HL, evaluated at 473 nm wavelength. A theoretical study of aberrations was carried out to qualitatively evaluate the experimental results obtained.
RESUMEN
In this work, an accurate numerical modeling of the diffraction properties of transmission holographic polymer dispersed liquid crystal (H-PDLC) gratings is presented. The method considers ellipsoid geometry-based liquid crystal (LC) droplets with random properties regarding size and location across the H-PLDC layer and also the non-homogeneous orientation of the LC director within the droplet. The direction of the LC director inside the droplets can be varied to reproduce the effects of the external voltage applied in H-PDLC-based gratings. From the LC director distribution in the droplet, the permittivity tensor is defined, which establishes the optical anisotropy of the media, and it is used for numerically solving the light propagation through the system. In this work, the split-field finite-difference time-domain method (SF-FDTD) is applied. This method is suited for accurately analyzing periodic media, and it considers spatial and time discretisation of Maxwell's equations. The scheme proposed here is used to investigate the influence on the diffraction properties of H-PDLC as a function of the droplets size and the bulk fraction of LC dispersed material.
RESUMEN
We study the behavior of a nanoparticle-polymer composite (NPC) material, based on a thiol-ene monomer system, working with long grating spacing. Thus, we evaluate the suitability of the NPC for storing complex diffractive optical elements with sharp profiles, such as blazed gratings. Using holographic methods, we measure the "apparent" diffusion of the material and the influence of the spatial period on this diffusion. The applicability of this material in complex diffractive optical elements (DOEs) recording is analyzed using an interferometric method. Supported by the results of this analysis, we record blazed gratings with different grating spacing and measure the maximum diffraction efficiency (DE) achieved. The results show that NPC has a good behavior in this range of spatial frequencies.
RESUMEN
The improvements made in diffusion models simulating phase image recording in photopolymers enable the optimization of a wide range of complex diffractive optical elements (DOEs), while the miniaturization of spatial light modulators makes it possible to generate both symmetric and non-symmetric DOEs. In addition, there is increasing interest in the design of new friendly recording materials. In this respect, photopolymers are a promising material due to their optical properties. In this paper, we show a procedure to record diffractive spherical lenses using a nontoxic optimized photopolymer. To achieve this goal, we followed three steps: first, the chemical optimization for DOE recording; second, the recording material characterization to be simulated by a three-dimensional diffusion model; and third, the evaluation of the coverplating for the conservation of the DOE.