Sensitivity of Pharmacokinetics to Differences in the Particle Size Distribution for Formulations of Locally Acting Mometasone Furoate Suspension-Based Nasal Sprays.

To assess bioequivalence of locally acting suspension-based nasal sprays, the U.S. FDA currently recommends a weight-of-evidence approach. In addition to in vitro and human pharmacokinetic (PK) studies, this includes a comparative clinical endpoint study to ensure equivalent bioavailability of the active pharmaceutical ingredient (API) at the site of action. The present study aimed to assess, within an in vitro/in vivo correlation paradigm, whether PK studies and dissolution kinetics are sensitive to differences in drug particle size for a locally acting suspension-based nasal spray product. Two investigational suspension-based nasal formulations of mometasone furoate (MF-I and MF-II; delivered dose: 180 µg) differed in API particle size and were compared in a single-center, double-blind, single-dose, randomized, two-way crossover PK study in 44 healthy subjects with oral charcoal block. Morphology-directed Raman spectroscopy yielded volume median diameters of 3.17 µm for MF-I and 5.50 µm for MF-II, and dissolution studies showed that MF-II had a slower dissolution profile than MF-I. The formulation with larger API particles (MF-II) showed a 45% smaller Cmax and 45% smaller AUC0-inf compared to those of MF-I. Systemic bioavailability of MF-I (2.20%) and MF-II (1.18%) correlated well with the dissolution kinetics, with the faster dissolving formulation yielding the higher bioavailability. This agreement between pharmacokinetics and dissolution kinetics cross-validated both methods and supported their use in assessing potential differences in slowly dissolving suspension-based nasal spray products.

Optimization of the Transwell® System for Assessing the Dissolution Behavior of Orally Inhaled Drug Products through In Vitro and In Silico Approaches.

The aim of this study was to further evaluate and optimize the Transwell® system for assessing the dissolution behavior of orally inhaled drug products (OIDPs), using fluticasone propionate as a model drug. Sample preparation involved the collection of a relevant inhalable dose fraction through an anatomical mouth/throat model, resulting in a more uniform presentation of drug particles during the subsequent dissolution test. The method differed from previously published procedures by (1) using a 0.4 µm polycarbonate (PC) membrane, (2) stirring the receptor compartment, and (3) placing the drug-containing side of the filter paper face downwards, towards the PC membrane. A model developed in silico, paired with the results of in vitro studies, suggested that a dissolution medium providing a solubility of about 5 µg/mL would be a good starting point for the method's development, resulting in mean transfer times that were about 10 times longer than those of a solution. Furthermore, the model suggested that larger donor/receptor and sampling volumes (3, 3.3 and 2 mL, respectively) will significantly reduce the so-called "mass effect". The outcomes of this study shed further light on the impact of experimental conditions on the complex interplay of dissolution and diffusion within a volume-limited system, under non-sink conditions.

Can Pharmacokinetic Studies Assess the Pulmonary Fate of Dry Powder Inhaler Formulations of Fluticasone Propionate?

In the context of streamlining generic approval, this study assessed whether pharmacokinetics (PK) could elucidate the pulmonary fate of orally inhaled drug products (OIDPs). Three fluticasone propionate (FP) dry powder inhaler (DPI) formulations (A-4.5, B-3.8, and C-3.7), differing only in type and composition of lactose fines, exhibited median mass aerodynamic diameter (MMAD) of 4.5 µm (A-4.5), 3.8 µm (B-3.8), and 3.7 µm (C-3.7) and varied in dissolution rates (A-4.5 slower than B-3.8 and C-3.7). In vitro total lung dose (TLDin vitro) was determined as the average dose passing through three anatomical mouth-throat (MT) models and yielded dose normalization factors (DNF) for each DPI formulation X (DNFx = TLDin vitro,x/TLDin vitro,A-4.5). The DNF was 1.00 for A-4.5, 1.32 for B-3.8, and 1.21 for C-3.7. Systemic PK after inhalation of 500 µg FP was assessed in a randomized, double-blind, four-way crossover study in 24 healthy volunteers. Peak concentrations (Cmax) of A-4.5 relative to those of B-3.8 or C-3.7 lacked bioequivalence without or with dose normalization. The area under the curve (AUC0-Inf) was bio-IN-equivalent before dose normalization and bioequivalent after dose normalization. Thus, PK could detect differences in pulmonary available dose (AUC0-Inf) and residence time (dose-normalized Cmax). The differences in dose-normalized Cmax could not be explained by differences in in vitro dissolution. This might suggest that Cmax differences may indicate differences in regional lung deposition. Overall this study supports the use of PK studies to provide relevant information on the pulmonary performance characteristics (i.e., available dose, residence time, and regional lung deposition).