Magnesium Nanoparticles for Surface-Enhanced Raman Scattering and Plasmon-Driven Catalysis.

Nanostructures of some metals can sustain localized surface plasmon resonances, collective oscillations of free electrons excited by incident light. This effect results in wavelength-dependent absorption and scattering, enhancement of the incident electric field at the metal surface, and generation of hot carriers as a decay product. The enhanced electric field can be utilized to amplify the spectroscopic signal in surface-enhanced Raman scattering (SERS), while hot carriers can be exploited for catalytic applications. In recent years, cheaper and more earth abundant alternatives to traditional plasmonic Au and Ag have gained growing attention. Here, we demonstrate the ability of plasmonic Mg nanoparticles to enhance Raman scattering and drive chemical transformations upon laser irradiation. The plasmonic properties of Mg nanoparticles are characterized at the bulk and single particle level by optical spectroscopy and scanning transmission electron microscopy coupled with electron energy-loss spectroscopy and supported by numerical simulations. SERS enhancement factors of ∼102 at 532 and 633 nm are obtained using 4-mercaptobenzoic acid and 4-nitrobenzenethiol. Furthermore, the reductive coupling of 4-nitrobenzenethiol to 4,4'-dimercaptoazobenzene is observed on the surface of Mg nanoparticles under 532 nm excitation in the absence of reducing agents, indicating a plasmon-driven catalytic process. Once decorated with Pd, Mg nanostructures display an enhancement factor of 103 along with an increase in the rate of catalytic coupling. The results of this study demonstrate the successful application of plasmonic Mg nanoparticles in sensing and plasmon-enhanced catalysis.

Plasmonic Properties of Self-Assembled Gold Nanocrescents: Implications for Chemical Sensing.

A bottom-up approach, the Langmuir-Blodgett technique, is used for the preparation of composite thin films of gold nanoparticles and polymers: poly(styrene-b-2-vinylpyridine), poly-2-vinylpyridine, and polystyrene. The self-assembly of poly(styrene-b-2-vinylpyridine) at the air-water interface leads to the formation of surface micelles, which serve as a template for the organization of gold nanoparticles into ring assemblies. By using poly-2-vinylpyridine in conjunction with low surface pressure, the distance between nanostructures can be increased, allowing for optical characterization of single nanostructures. Once deposited on a solid substrate, the preorganized gold nanoparticles are subjected to further growth by the reduction of additional gold, leading to a variety of nanostructures which can be divided into two categories: nanocrescents and circular arrays of nanoparticles. The optical properties of individual structures are investigated by optical dark-field spectroscopy and numerical calculations. The plasmonic behavior of the nanostructures is elucidated through the correlation of optical properties with structural features and the identification of dominant plasmon modes. Being based on a self-assembly approach, the reported method allows for the formation of interesting plasmonic materials under ambient conditions, at a relatively large scale, and at low cost. These attributes, in addition to the resonances located in the near-infrared region of the spectrum, make nanocrescents candidates for biological and chemical sensing.

Far-field, near-field and photothermal response of plasmonic twinned magnesium nanostructures.

Magnesium nanoparticles offer an alternative plasmonic platform capable of resonances across the ultraviolet, visible and near-infrared. Crystalline magnesium nanoparticles display twinning on the (101̄1), (101̄2), (101̄3), and (112̄1) planes leading to concave folded shapes named tents, chairs, tacos, and kites, respectively. We use the Wulff-based Crystal Creator tool to expand the range of Mg crystal shapes with twinning over the known Mg twin planes, i.e., (101̄x), x = 1, 2, 3 and (112̄y), y = 1, 2, 3, 4, and study the effects of relative facet expression on the resulting shapes. These shapes include both concave and convex structures, some of which have been experimentally observed. The resonant modes, far-field, and near-field optical responses of these unusual plasmonic shapes as well as their photothermal behaviour are reported, revealing the effects of folding angle and in-filling of the concave region. Significant differences exist between shapes, in particular regarding the maximum and average electric field enhancement. A maximum field enhancement (|E|/|E0|) of 184, comparable to that calculated for Au and Ag nanoparticles, was found at the tips of the (112̄4) kite. The presence of a 5 nm MgO shell is found to decrease the near-field enhancement by 67% to 90% depending on the shape, while it can increase the plasmon-induced temperature rise by up to 42%. Tip rounding on the otherwise sharp nanoparticle corners also significantly affects the maximum field enhancement. These results provide guidance for the design of enhancing and photothermal substrates for a variety of plasmonic applications across a wide spectral range.

Halide-assisted differential growth of chiral nanoparticles with threefold rotational symmetry.

Enriching the library of chiral plasmonic nanoparticles that can be chemically mass-produced will greatly facilitate the applications of chiral plasmonics in areas ranging from constructing optical metamaterials to sensing chiral molecules and activating immune cells. Here we report on a halide-assisted differential growth strategy that can direct the anisotropic growth of chiral Au nanoparticles with tunable sizes and diverse morphologies. Anisotropic Au nanodisks are employed as seeds to yield triskelion-shaped chiral nanoparticles with threefold rotational symmetry and high dissymmetry factors. The averaged scattering g-factors of the L- and D-nanotriskelions are as large as 0.57 and - 0.49 at 650 nm, respectively. The Au nanotriskelions have been applied in chiral optical switching devices and chiral nanoemitters. We also demonstrate that the manipulation of the directional growth rate enables the generation of a variety of chiral morphologies in the presence of homochiral ligands.

Synthesis of Controllable Cu Shells on Au Nanoparticles with Electrodeposition: A Systematic in Situ Single Particle Study.

Bimetallic Cu on Au nanoparticles with controllable morphology and optical properties were obtained via electrochemical synthesis. In particular, multilobed structures with good homogeneity were achieved through the optimization of experimental parameters such as deposition current, charge transfer, and metal ion concentration. A hyperspectral dark field scattering setup was used to characterize the electrodeposition on a single particle level, with changes in localized surface plasmon resonance frequency correlated with deposition charge transfer and amount of Cu deposited as determined by electron microscopy. This demonstrated the ability to tune morphology and spectra through electrochemical parameters alone. Time-resolved in situ measurements of single particle spectra were obtained, giving an insight into the kinetics of the deposition process. Nucleation of multiple cubes of Cu initially occurs preferentially on the tips of Au nanoparticles, before growing and coalescing to form a multilobed, lumpy shell. Modifying the surface of Au nanoparticles by plasma treatment resulted in thicker and more uniform Cu shells.

Opportunities and Challenges for Alternative Nanoplasmonic Metals: Magnesium and Beyond.

Materials that sustain localized surface plasmon resonances have a broad technology potential as attractive platforms for surface-enhanced spectroscopies, chemical and biological sensing, light-driven catalysis, hyperthermal cancer therapy, waveguides, and so on. Most plasmonic nanoparticles studied to date are composed of either Ag or Au, for which a vast array of synthetic approaches are available, leading to controllable size and shape. However, recently, alternative materials capable of generating plasmonically enhanced light-matter interactions have gained prominence, notably Cu, Al, In, and Mg. In this Perspective, we give an overview of the attributes of plasmonic nanostructures that lead to their potential use and how their performance is dictated by the choice of plasmonic material, emphasizing the similarities and differences between traditional and emerging plasmonic compositions. First, we discuss the materials limitation encapsulated by the dielectric function. Then, we evaluate how size and shape maneuver localized surface plasmon resonance (LSPR) energy and field distribution and address how this impacts applications. Next, biocompatibility, reactivity, and cost, all key differences underlying the potential of non-noble metals, are highlighted. We find that metals beyond Ag and Au are of competitive plasmonic quality. We argue that by thinking outside of the box, i.e., by looking at nonconventional materials such as Mg, one can broaden the frequency range and, more importantly, combine the plasmonic response with other properties essential for the implementation of plasmonic technologies.

Size Control in the Colloidal Synthesis of Plasmonic Magnesium Nanoparticles.

Nanoparticles of plasmonic materials can sustain oscillations of their free electron density, called localized surface plasmon resonances (LSPRs), giving them a broad range of potential applications. Mg is an earth-abundant plasmonic material attracting growing attention owing to its ability to sustain LSPRs across the ultraviolet, visible, and near-infrared wavelength range. Tuning the LSPR frequency of plasmonic nanoparticles requires precise control over their size and shape; for Mg, this control has previously been achieved using top-down fabrication or gas-phase methods, but these are slow and expensive. Here, we systematically probe the effects of reaction parameters on the nucleation and growth of Mg nanoparticles using a facile and inexpensive colloidal synthesis. Small NPs of 80 nm were synthesized using a low reaction time of 1 min and ∼100 nm NPs were synthesized by decreasing the overall reaction concentration, replacing the naphthalene electron carrier with biphenyl or using metal salt additives of FeCl3 or NiCl2 at longer reaction times of 17 h. Intermediate sizes up to 400 nm were further selected via the overall reaction concentration or using other metal salt additives with different reduction potentials. Significantly larger particles of over a micrometer were produced by reducing the reaction temperature and, thus, the nucleation rate. We showed that increasing the solvent coordination reduced Mg NP sizes, while scaling up the reaction reduced the mixing efficiency and produced larger NPs. Surprisingly, varying the relative amounts of Mg precursor and electron carrier had little impact on the final NP sizes. These results pave the way for the large-scale use of Mg as a low-cost and sustainable plasmonic material.

Approaches to modelling the shape of nanocrystals.

Unlike in the bulk, at the nanoscale shape dictates properties. The imperative to understand and predict nanocrystal shape led to the development, over several decades, of a large number of mathematical models and, later, their software implementations. In this review, the various mathematical approaches used to model crystal shapes are first overviewed, from the century-old Wulff construction to the year-old (2020) approach to describe supported twinned nanocrystals, together with a discussion and disambiguation of the terminology. Then, the multitude of published software implementations of these Wulff-based shape models are described in detail, describing their technical aspects, advantages and limitations. Finally, a discussion of the scientific applications of shape models to either predict shape or use shape to deduce thermodynamic and/or kinetic parameters is offered, followed by a conclusion. This review provides a guide for scientists looking to model crystal shape in a field where ever-increasingly complex crystal shapes and compositions are required to fulfil the exciting promises of nanotechnology.

Facet- and Gas-Dependent Reshaping of Au Nanoplates by Plasma Treatment.

The reshaping of metal nanocrystals on substrates is usually realized by pulsed laser irradiation or ion-beam milling with complex procedures. In this work, we demonstrate a simple method for reshaping immobilized Au nanoplates through plasma treatment. Au nanoplates can be reshaped gradually with nearly periodic right pyramid arrays formed on the surface of the nanoplates. The gaseous environment in the plasma-treatment system plays a significant role in the reshaping process with only nitrogen-containing environments leading to reshaping. The reshaping phenomenon is facet-dependent, with right pyramids formed only on the exposed {111} facets of the Au nanoplates. The morphological change of the Au nanoplates induced by the plasma treatment leads to large plasmon peak redshifts. The reshaped Au nanoplates possess slightly higher refractive index sensitivities and largely increased surface-enhanced Raman scattering intensities compared to the flat, untreated nanoplates. Our results offer insights for studying the interaction mechanism between plasma and the different facets of noble metal nanocrystals and an approach for reshaping light-interacting noble metal nanocrystals.

On the identification of twinning in body-centred cubic nanoparticles.

Many metals and alloys, including Fe and W, adopt body-centred cubic (BCC) crystal structures and nanoparticles of these metals are gaining significant scientific and industrial relevance. Twinning has a marked effect on catalytic activity, yet there is little evidence for or against the presence of twinning in BCC nanoparticles. Here, we explore the potential shapes of twinned BCC nanoparticles, and predict their electron microscopy and diffraction signatures. BCC single crystal and twinned shapes often appear similar and diffraction patterns along common, low-index zone axes are often indistinguishable, casting doubt on many claims of single crystallinity. We conclude by outlining how nanoparticles can be characterized to conclusively prove the presence or absence of twinning.

Tents, Chairs, Tacos, Kites, and Rods: Shapes and Plasmonic Properties of Singly Twinned Magnesium Nanoparticles.

Nanostructures of some metals can sustain light-driven electron oscillations called localized surface plasmon resonances, or LSPRs, that give rise to absorption, scattering, and local electric field enhancement. Their resonant frequency is dictated by the nanoparticle (NP) shape and size, fueling much research geared toward discovery and control of new structures. LSPR properties also depend on composition; traditional, rare, and expensive noble metals (Ag, Au) are increasingly eclipsed by earth-abundant alternatives, with Mg being an exciting candidate capable of sustaining resonances across the ultraviolet, visible, and near-infrared spectral ranges. Here, we report numerical predictions and experimental verifications of a set of shapes based on Mg NPs displaying various twinning patterns including (101̅1), (101̅2), (101̅3), and (112̅1), that create tent-, chair-, taco-, and kite-shaped NPs, respectively. These are strikingly different from what is obtained for typical plasmonic metals because Mg crystallizes in a hexagonal close packed structure, as opposed to the cubic Al, Cu, Ag, and Au. A numerical survey of the optical response of the various structures, as well as the effect of size and aspect ratio, reveals their rich array of resonances, which are supported by single-particle optical scattering experiments. Further, corresponding numerical and experimental studies of the near-field plasmon distribution via scanning transmission electron microscopy electron-energy loss spectroscopy unravels a mode nature and distribution that are unlike those of either hexagonal plates or cylindrical rods. These NPs, made from earth-abundant Mg, provide interesting ways to control light at the nanoscale across the ultraviolet, visible, and near-infrared spectral ranges.

Wulff-Based Approach to Modeling the Plasmonic Response of Single Crystal, Twinned, and Core-Shell Nanoparticles.

The growing interest in plasmonic nanoparticles and their increasingly diverse applications is fuelled by the ability to tune properties via shape control, promoting intense experimental and theoretical research. Such shapes are dominated by geometries that can be described by the kinetic Wulff construction such as octahedra, thin triangular platelets, bipyramids, and decahedra, to name a few. Shape is critical in dictating the optical properties of these nanoparticles, in particular their localized surface plasmon resonance behavior, which can be modeled numerically. One challenge of the various available computational techniques is the representation of the nanoparticle shape. Specifically, in the discrete dipole approximation, a particle is represented by discretizing space via an array of uniformly distributed points-dipoles; this can be difficult to construct for complex shapes including those with multiple crystallographic facets, twins, and core-shell particles. Here, we describe a standalone user-friendly graphical user interface (GUI) that uses both kinetic and thermodynamic Wulff constructions to generate a dipole array for complex shapes, as well as the necessary input files for DDSCAT-based numerical approaches. Examples of the use of this GUI are described through three case studies spanning different shapes, compositions, and shell thicknesses. Key advances offered by this approach, in addition to simplicity, are the ability to create crystallographically correct structures and the addition of a conformal shell on complex shapes.

Decoration of plasmonic Mg nanoparticles by partial galvanic replacement.

Plasmonic structures have attracted much interest in science and engineering disciplines, exploring a myriad of potential applications owing to their strong light-matter interactions. Recently, the plasmonic concentration of energy in subwavelength volumes has been used to initiate chemical reactions, for instance by combining plasmonic materials with catalytic metals. In this work, we demonstrate that plasmonic nanoparticles of earth-abundant Mg can undergo galvanic replacement in a nonaqueous solvent to produce decorated structures. This method yields bimetallic architectures where partially oxidized 200-300 nm Mg nanoplates and nanorods support many smaller Au, Ag, Pd, or Fe nanoparticles, with potential for a stepwise process introducing multiple decoration compositions on a single Mg particle. We investigated this mechanism by electron-beam imaging and local composition mapping with energy-dispersive X-ray spectroscopy as well as, at the ensemble level, by inductively coupled plasma mass spectrometry. High-resolution scanning transmission electron microscopy further supported the bimetallic nature of the particles and provided details of the interface geometry, which includes a Mg oxide separation layer between Mg and the other metal. Depending on the composition of the metallic decorations, strong plasmonic optical signals characteristic of plasmon resonances were observed in the bulk with ultraviolet-visible spectrometry and at the single particle level with darkfield scattering. These novel bimetallic and multimetallic designs open up an exciting array of applications where one or multiple plasmonic structures could interact in the near-field of earth-abundant Mg and couple with catalytic nanoparticles for applications in sensing and plasmon-assisted catalysis.