OLED catheters for inner-body phototherapy: A case of type 2 diabetes mellitus improved via duodenal photobiomodulation.

Phototherapeutics has shown promise in treating various diseases without surgical or drug interventions. However, it is challenging to use it in inner-body applications due to the limited light penetration depth through the skin. Therefore, we propose an organic light-emitting diode (OLED) catheter as an effective photobiomodulation (PBM) platform useful for tubular organs such as duodenums. A fully encapsulated highly flexible OLED is mounted over a round columnar structure, producing axially uniform illumination without local hotspots. The biocompatible and airtight OLED catheter can operate in aqueous environments for extended periods, meeting the essential requirements for inner-body medical applications. In a diabetic Goto-Kakizaki (GK) rat model, the red OLED catheter delivering 798 mJ of energy is shown to reduce hyperglycemia and insulin resistance compared to the sham group. Results are further supported by the subdued liver fibrosis, illustrating the immense potential of the OLED-catheter-based internal PBM for the treatment of type 2 diabetes and other diseases yet to be identified.

Investigating the electrical crosstalk effect between pixels in high-resolution organic light-emitting diode microdisplays.

Organic light-emitting diode (OLED) microdisplays have received great attention owing to their excellent performance for augmented reality/virtual reality devices applications. However, high pixel density of OLED microdisplay causes electrical crosstalk, resulting in color distortion. This study investigated the current crosstalk ratio and changes in the color gamut caused by electrical crosstalk between sub-pixels in high-resolution full-color OLED microdisplays. A pixel structure of 3147 pixels per inch (PPI) with four sub-pixels and a single-stack white OLED with red, green, and blue color filters were used for the electrical crosstalk simulation. The results showed that the sheet resistance of the top and bottom electrodes of OLEDs rarely affected the electrical crosstalk. However, the current crosstalk ratio increased dramatically and the color gamut decreased as the sheet resistance of the common organic layer decreased. Furthermore, the color gamut of the OLED microdisplay decreased as the pixel density of the panel increased from 200 to 5000 PPI. Additionally, we fabricated a sub-pixel circuit to measure the electrical crosstalk current using a 3147 PPI scale multi-finger-type pixel structure and compared it with the simulation result.

Color gamut change by optical crosstalk in high-resolution organic light-emitting diode microdisplays.

Herein, the color gamut change by optical crosstalk between sub-pixels in high-resolution full-color organic light-emitting diode (OLED) microdisplays was numerically investigated. The color gamut of the OLED microdisplay decreased dramatically as the pixel density of the panel increased from 100 pixels per inch (PPI) to 3000 PPI. In addition, the increase in thickness of the passivation layer between the bottom electrode and the top color filter results in a decrease in the color gamut. We also calculated the color gamut change depending on the pixel structures in the practical OLED microdisplay panel, which had an aspect ratio of 32:9 and a pixel density of 2,490 PPI. The fence angle and height, refractive index of the passivation layer, black matrix width, and white OLED device structure affect the color gamut of the OLED microdisplay panel because of the optical crosstalk effect.

Organic/Inorganic Hybrid Thin-Film Encapsulation Using Inkjet Printing and PEALD for Industrial Large-Area Process Suitability and Flexible OLED Application.

We present herein the first report of organic/inorganic hybrid thin-film encapsulation (TFE) developed as an encapsulation process for mass production in the display industry. The proposed method was applied to fabricate a top-emitting organic light-emitting device (TEOLED). The organic/inorganic hybrid TFE has a 1.5 dyad structure and was fabricated using plasma-enhanced atomic layer deposition (PEALD) and inkjet printing (IJP) processes that can be applied to mass production operations in the industry. Currently, industries use inorganic thin films such as SiNx and SiOxNy fabricated through plasma-enhanced chemical vapor deposition (PECVD), which results in film thickness >1 µm; however, in the present work, an Al2O3 inorganic thin film with a thickness of 30 nm was successfully fabricated using ALD. Furthermore, to decouple the crack propagation between the adjacent Al2O3 thin films, an acrylate-based polymer layer was printed between these layers using IJP to finally obtain the 1.5 dyad hybrid TFE. The proposed method can be applied to optoelectronic devices with various form factors such as rollables and stretchable displays. The hybrid TFE developed in this study has a transmittance of 95% or more in the entire visible light region and a very low surface roughness of less than 1 nm. In addition, the measurement of water vapor transmission rate (WVTR) using commercial MOCON equipment yielded a value of 5 × 10-5 gm-2 day-1 (37.8 °C and 100% RH) or less, approaching the limit of the measuring equipment. The TFE was applied to TEOLEDs and the improvement in optical properties of the device was demonstrated. The OLED panel was manufactured and operated stably, showing excellent consistency even in the actual display manufacturing process. The panel operated normally even after 363 days in air. The proposed organic/inorganic hybrid encapsulant manufacturing process is applicable to the display industry and this study provides basic guidelines that can serve as a foothold for the development of various technologies in academia and industry alike.

Thin-film transistor-driven vertically stacked full-color organic light-emitting diodes for high-resolution active-matrix displays.

Thin-film transistor (TFT)-driven full-color organic light-emitting diodes (OLEDs) with vertically stacked structures are developed herein using photolithography processes, which allow for high-resolution displays of over 2,000 pixels per inch. Vertical stacking of OLEDs by the photolithography process is technically challenging, as OLEDs are vulnerable to moisture, oxygen, solutions for photolithography processes, and temperatures over 100 °C. In this study, we develop a low-temperature processed Al2O3/SiNx bilayered protection layer, which stably protects the OLEDs from photolithography process solutions, as well as from moisture and oxygen. As a result, transparent intermediate electrodes are patterned on top of the OLED elements without degrading the OLED, thereby enabling to fabricate the vertically stacked OLED. The aperture ratio of the full-color-driven OLED pixel is approximately twice as large as conventional sub-pixel structures, due to geometric advantage, despite the TFT integration. To the best of our knowledge, we first demonstrate the TFT-driven vertically stacked full-color OLED.

Color-tunable organic light-emitting diodes with vertically stacked blue, green, and red colors for lighting and display applications.

We demonstrate independently and simultaneously controlled color-tunable organic light-emitting diodes (OLEDs) with vertically stacked blue, green, and red elements. The blue, green, and red elements were placed at the bottom, middle, and top positions, respectively, forming color-tunable OLEDs. The independently driven blue, green, and red elements in the color-tunable OLEDs exhibited low driving voltages of 5.3 V, 3.0 V, and 4.6 V, as well as high external quantum efficiencies of 11.1%, 10.9%, and 9.6%, respectively, at approximately 1000 cd/m2. Each element in the color-tunable OLEDs showed high-purity blue, green, and red colors with little parasitic emission owing to the delicately designed device structure resultant from optical simulations. The color-tunable OLEDs could produce any colors inside the triangle formed with blue (0.136, 0.261), green (0.246, 0.697), and red (0.614, 0.386) Commission Internationale de l'éclairage (CIE) 1931 color coordinates. In addition, the correlated color temperatures (CCTs) of white colors in the color-tunable OLED can be easily changed from the warm white to the cool white by controlling the red, green, and blue emissions simultaneously. The white colors in the color-tunable OLED have the CIE 1931 color coordinate of (0.304, 0.351), with a CCT of 6289 K and (0.504, 0.440), with a CCT of 2407K at the driving voltage of 5 V (blue), 2.8 V (green), 4.4 V (red), and 4.6 V (blue), 3 V (green), 5 V (red), respectively. Furthermore, the white color in the color-tunable OLED exhibited a high color rendering index (~88.7) due to vertically stacked three color system. Moreover, we successfully fabricated a large-sized, 14 × 12 pixel array of the color-tunable OLEDs to demonstrate lighting and display applications, respectively.