Comparison of different approaches for the estimation of odour emissions from landfill surfaces.

The aim of this study is related to the assessment of odour emissions from landfill surfaces. Up to now, there is not a widely accepted method to quantify odour emissions from this particular kind of source. Five different methods were developed and investigated. These methods can be considered as based on three distinct approaches, both experimental and computational. The first approach provides to use models for the estimation the landfill gas production, whereby the second and the third approach are based on direct measurement campaigns on the landfill surface: for the determination of the methane concentration or for the direct measurement of the odour concentration, respectively. The methods were then compared in terms of specific odour emission rates by referring to other literature data. Finally, dispersion modelling was applied in order to allow a further comparison of the resulting odour impacts with other olfactometric data from independent monitoring campaigns on the studied site.

Gastric GISTs: Analysis of c-Kit, PDGFRA and BRAF mutations in relation to prognosis and clinical pathological characteristics of patients - A GIRCG study.

BACKGROUND: Gastric gastrointestinal stromal tumors (GISTs) represent a subgroup of GISTs with a better prognosis than those located in other areas. In this retrospective study we performed a molecular characterization of a large series of patients with gastric GISTs in relation to clinical-pathological characteristics and prognosis. METHODS: DNA was extracted from paraffin-embedded sections from 221 gastric GIST patients submitted to surgery. Exons 9, 11, 13 and 17 of KIT, exons 12 and 18 of PDGFRA and exons 11 and 15 of BRAF were analyzed by direct sequencing. Cox regression analysis adjusted for clinical-pathological factors was performed to evaluate KIT and PDGFRA mutations in relation to the composite endpoint of relapse or death. RESULTS: KIT and PDGFRA mutations were observed in 119 (53.8%) and 56 (25.3%) patients, respectively, whereas 46 (20.8%) patients had wild type (wt) disease. Univariable analyses showed that a high Miettinen risk category and the presence of ulceration and KIT deletions were associated with increased risk of relapse or death (p < 0.001; p = 0.0389 and p = 0.002, respectively). After adjusting for Miettinen risk score, KIT deletions remained an independent prognostic factor (HRadj = 2.65, 95% CI [1.15-6.13], p = 0.023). Moreover, KIT deletions in exon 11 codons 557, 558 or 559 were associated with a higher risk of relapse or death than wt tumors (HRadj = 3.29 95% CI [1.64-6.64], p = 0.001). CONCLUSIONS: KIT deletions in exon 11, especially those involving codons 557, 558 or 559, were correlated with a more aggressive gastric GIST phenotype and increased risk of relapse or death.

Role of BRAF molecular analysis in the management of papillary thyroid carcinoma: analysis of cytological and histological samples.

BACKGROUND: Although fine needle aspiration (FNA) is the standard diagnostic test for the characterization of a suspicious thyroid nodule, in some cases cytological evaluation is inconclusive. The aim of this study was to determine the role of BRAF mutation in aiding diagnosis and to verify whether archival cytological samples could be suitable for molecular analysis. METHODS: Eighty-five patients with suspicious (Thy4) or follicular (Thy3) lesions on cytology were resubmitted to a second FNA for BRAF mutation analysis. Of these, 56 subsequently underwent surgery. The usefulness of archival samples for molecular analysis was also studied in a second cohort of 42 patients with a confirmed diagnosis of papillary thyroid carcinoma for whom both archived paraffin-embedded histological samples and cytological smears were available. A further 15 patients with paired fresh FNA and archived cytological and histological samples were recruited. RESULTS: BRAF mutation was found in the fresh FNA samples from 10 of 56 patients who had surgery with previous inconclusive cytology (4/45, 9%, Thy3 and 6/11, 55%, Thy4). The BRAF test showed a specificity and positive predictive value of 100% (26/26 and 10/10, respectively), sensitivity of 33% (10/30) and negative predictive value of 57% (26/46). There was absolute concordance between the BRAF results obtained with 42 histological and cytological archived samples. BRAF analysis on 15 archived cytological samples showed absolute concordance with histology, whereas there was one false negative on the matched fresh FNA. CONCLUSION: BRAF analysis is a highly specific test that can facilitate cytological diagnosis in some cases and can also be performed on archived cytological samples.

Methodology for assessing the performance of urine absorbing aids in controlling malodour release.

The aim of this study was to investigate the possibility of comparing the performance of different absorbent aids in terms of odour control by discussing a suitable methodology for product evaluation. To overcome the problems of low test reproducibility owing to biological urine variability, the first step of the work consisted of the identification and the production of artificial urine having a constant and stable composition over time, moreover preventing sensorial assessors from any risk of biological contamination. Sensorial measurements were performed to optimize the similarity between artificial and biological urine, especially as far as the composition of the volatile component and therefore of the odour properties are concerned. The assessment of absorbent articles performance to control urine malodour includes both the concentration and the hedonic tone of the odour released by the article itself loaded with synthetic urine. Analyses were run on different products, which can be grouped into two different classes: absorbing aids with or without odour control technology (OCT) respectively. Results show that, despite of the presence or absence of OCT on absorbing products, their odour concentrations are almost identical, being comprised between 10 000 and 12 000 ouE m(-3) . For this reason, it is evident that odour concentration is not suitable as the sole parameter for comparison of different absorbing products. Instead, the hedonic odour tone (odour pleasantness/unpleasantness) relevant to the different product typologies (that is products with and without OCT) should be used as an additional discriminating factor for this kind of comparative tests.

Dermatosis perforantes: presentación de 8 casos / Perforating dermatosis: report of 8 cases

Las dermatosis perforantes (DP) o enfermedades por eliminación transepidérmica son un grupo de entidades caracterizadas por la extrusión de material dérmico alterado a través de la epidermis que incluye a la colagenosis perforante reactiva, la elastolisis perforante serpiginosa, la foliculitis perforante y la enfermedad de Kyrle. Se caracterizan por la aparición de pápulo-nódulos centrados por tapones o costras queratósicas, pruriginosos. Entre las opciones terapéuticas se describen los antihistamínicos, fototerapia y corticoides intralesionales, con resultados variables. Objetivos. Describir 8 casos de dermatosis perforante diagnosticados en nuestro servicio. Materiales y Métodos. Se realizó un estudio retrospectivo, observacional y descriptivo que evaluó las características clínicas, histológicas y la asociación con patología sistémica de los pacientes con diagnóstico histológico de dermatosis perforante que concurrieron a nuestro servicio entre septiembre de 2006 y julio de 2010.Resultados. Se diagnosticaron 8 pacientes con dermatosis perforante. Del total, 5 (62,5%) fueron hombres y 3 mujeres (37,5%). La edad media de presentación fue de 57,12 años (37-71 años); 6 (75%) correspondían a enfermedad de Kyrle y 2 (25%) a foliculitis perforante; 6 (75%) se asociaban a insuficiencia renal crónica, 6 (75%) a diabetes mellitus, 1 (12,5%) a insuficiencia renal aguda y 6 (75%) a enfermedad cardiovascular. Conclusiones. Si bien la mayoría de nuestros pacientes tenían antecedentes de diabetes y/o insuficiencia renal crónica como se describe en la literatura, cabe destacar que en uno de ellos no se encontró ninguna de estas asociaciones. Adicionalmente, el 75% de los pacientes tenía antecedentes de enfermedad cardiovascular. Encontramos una mayor incidencia en hombres (62,5%) a diferencia de lo reportado en algunos trabajos (AU)

Perforating dermatosis (DP) comprises a group of diseases characterized by the extrusion of dermic debris through the epidermis. It includes reactive perforating collagenosis, perforating folliculitis, elastosis perforans serpiginosa and Kyrle's disease. It presents as multiple pruritic papulo nodules centered by a keratotic plug. Antihistamines, phototherapy and intralesional steroids are among the therapeutic options described, with variable results. Objectives. To describe 8 cases of perforating dermatosis diagnosed in our department. Materials and Methods. We conducted a retrospective, observational and descriptive study evaluating clinical and histological features and association with systemic disease, of the patients with a biopsy confirmed, perforating dermatosis between September 2006 and July 2010. Results. Eight patients with perforating dermatosis were diagnosed. Of them, 5 (62,5%) were male and 3 female (37,5%). Mean age of presentation was 57,12 years (37-71 years); 6 (75%) corresponded to Kyrle's disease and 2 (25%) to perforating folliculitis; 6 (75%) were associated with chronic renal insufficiency, 6 (75%) with diabetes mellitus, 1 (12,5%) with acute renal insufficiency and 6 (75%) with cardiovascular disease. Conclusions. Although most of our patients had a history of chronic renal insufficiency or diabetes, as described in the literature, in one of them no associated disease was found. Furthermore, 75% of the patients presented with cardiovascular disease. Unlike previous reports, we found agreater incidence in men (62,5%) over women (AU)

Olfactory and toxic impact of industrial odour emissions.

This paper describes the approach adopted for the evaluation both of the odour impact and of the non-carcinogenic health effects relevant to odours in the city of Terni, Italy. The first part of the study focused on the quantification of emissions by means of dynamic olfactometry and chemical analyses. Dispersion modelling was then applied for the evaluation of citizens' exposure both to odours and to their non-carcinogenic toxicity. The results show that, on one hand, the odour impact is considerable, actually affecting almost the whole city of Terni. On the other hand, the toxic impact, expressed in terms of the Hazard Index (HI), is about three orders of magnitude lower than the level that is expected to bring adverse effects, over a lifetime exposure, for human health.

Validation of a method for odor sampling on solid area sources.

The aim of this paper is the study and the validation of a method for odor sampling on solid area sources. This aim is achieved by considering a suitable theoretical model that accounts for all the variables involved in the volatilization process of odorous compounds from solids into the atmosphere. The simulation of the emission of odors from a solid surface was achieved by designing a suitable experimental setup and a specific wind tunnel for laboratory tests. The results of the tests show a good correspondence between the theoretical data derived from the adopted model and the experimental data. The verification of the possibility of describing the wind tunnel functioning with a theoretical volatilization model proves the applicability of this device for sampling on solid area sources.

Evaluating the dispersion of toxic odour emissions from complex sources.

This article describes an original approach for evaluating exposure to toxic odour emissions, based on methods commonly used for assessing the impact of odour, adopted in this specific case to examine the non-carcinogenic health effects of odours in the city of Terni, Italy. First the hazardous volatile organic compounds emitted from the main odour sources were identified and quantified by chemical analysis. The Hazard Index (HI) was used to assess the toxicity associated with the emissions. The HI is the sum of the concentrations of the hazardous compounds weighted with their Reference Concentration (RfC). A RfC is the estimated continuous inhalation concentration at which people are unlikely to risk any deleterious effects during their lifetime. Atmospheric dispersion modelling was based on the Toxicity Emission Rate (TER) which, like the Odour Emission Rate (OER) conventionally used to quantify odour emissions, relates the HI with the air flow of an emission source; it is as a simple but effective method for the general characterization of toxic odour emissions in complex scenarios. The results indicated that citizens' exposure to the non-carcinogenic toxic compounds involved in odour emissions was below the level expected to have adverse effects on human health. Classical risk assessment techniques should now be employed to define the pollutants and their effects better and to validate this approach.

Improvement of olfactometric measurement accuracy and repeatability by optimization of panel selection procedures.

The EN 13725:2003, which standardizes the determination of odour concentration by dynamic olfactometry, fixes the limits for panel selection in terms of individual threshold towards a reference gas (n-butanol in nitrogen) and of standard deviation of the responses. Nonetheless, laboratories have some degrees of freedom in developing their own procedures for panel selection and evaluation. Most Italian olfactometric laboratories use a similar procedure for panel selection, based on the repeated analysis of samples of n-butanol at a concentration of 60 ppm. The first part of this study demonstrates that this procedure may originate a sort of "smartening" of the assessors, which means that they become able to guess the right answers in order to maintain their qualification as panel members, independently from their real olfactory perception. For this reason, the panel selection procedure has been revised with the aim of making it less repetitive, therefore preventing the possibility for panel members to be able to guess the best answers in order to comply with the selection criteria. The selection of new panel members and the screening of the active ones according to this revised procedure proved this new procedure to be more selective than the "standard" one. Finally, the results of the tests with n-butanol conducted after the introduction of the revised procedure for panel selection and regular verification showed an effective improvement of the laboratory measurement performances in terms of accuracy and precision.

Design and validation of a wind tunnel system for odour sampling on liquid area sources.

The aim of this study is to describe the methods adopted for the design and the experimental validation of a wind tunnel, a sampling system suitable for the collection of gaseous samples on passive area sources, which allows to simulate wind action on the surface to be monitored. The first step of the work was the study of the air velocity profiles. The second step of the work consisted in the validation of the sampling system. For this purpose, the odour concentration of some air samples collected by means of the wind tunnel was measured by dynamic olfactometry. The results of the air velocity measurements show that the wind tunnel design features enabled the achievement of a uniform and homogeneous air flow through the hood. Moreover, the laboratory tests showed a very good correspondence between the odour concentration values measured at the wind tunnel outlet and the odour concentration values predicted by the application of a specific volatilization model, based on the Prandtl boundary layer theory. The agreement between experimental and theoretical trends demonstrate that the studied wind tunnel represents a suitable sampling system for the simulation of specific odour emission rates from liquid area sources without outward flow.

Isotachophoresis at pH extremes: theory and experimental validation.

The evolution of an isotachophoresis (ITP) system in acidic or basic pH ranges can be quite different from that predicted by the existing theory. It was found theoretically and proved experimentally that the contribution of hydrogen or hydroxyl ion to conductivity of solution and/or its net charge changes the behavior of the ITP system, creating in the terminating electrolyte an additional zone close to the initial interfaces between electrolytes (leader and terminator). One boundary of the zone, being either sharp or dispersed, moves toward the leader; the other is always sharp and stationary and coincides with initial electrolytes' discontinuity. The latter can be registered in the presence of electroosmotic flow which delivers it to the detection point. In order to describe the dynamics of the ITP system at pH extremes an algorithm of analytical solution was developed, based on the revised Kohlrausch theory. Its predictions coincide well with computer simulations and experimental data. The results presented can help in a correct analysis of ITP data and explain some confusing phenomena which were considered to be artifacts.

Wheat cultivar discrimination by capillary electrophoresis of gliadins in isoelectric buffers.

A modified method is reported for screening of wheat cultivars: capillary zone electrophoresis of gliadins in isoelectric buffers. Previously published procedures recommended a 100 mM phosphate buffer, supplemented with 0.05% hydroxypropylmethylcellulose and 20% acetonitrile, in uncoated capillaries. Due to the very high conductivity of such a buffer (4.7 mmhos at 25 degrees C) high speed separations (10-12 min analysis time at 800 V/cm) could only be elicited in 20 microm internal diameter (ID) capillaries, at the expense of sensitivity. In the present report, we optimized the background electrolyte as follows: 40 mM aspartic acid (pH=pI=2.77) in the presence of 7 M urea and 0.5% short-chain hydroxyethylcellulose (Mn 27000 Da; apparent pH 3.9 in 7 M urea). As an alternative recipe, the same isoelectric buffer can be supplemented with a mixed organic solvent composed of 4 M urea and 20% acetonitrile (apparent pH 3.66). Due to the much lower conductivity (0.7 mmhos), separations can be carried out at 1000 V/cm in only 10 min, but in larger bore capillaries (50 microm ID), ensuring a five-times higher sensitivity. The gliadin patterns thus obtained are species-specific and allow easy identification of all cultivars tested of both durum and bread wheat. No adsorption of proteins to the silica wall seems to occur and high reproducibility in peak areas and transit times is obtained.

Generation of tryptic maps of alpha- and beta-globin chains by capillary electrophoresis in isoelectric buffers.

A novel method for generating peptide maps, following tryptic digests of proteins, is reported here: capillary zone electrophoresis in the presence of isoelectric buffers as the sole buffering species. A typical buffer composition comprises 50 mM aspartic acid (pH = pI = 2.77), 0.5% hydroxyethyl cellulose (added as a dynamic coating agent for preventing peptide adsorption to weakly ionized silanols), 5% trifluoroethanol and 1% zwitterionic detergent (CHAPS). With this buffer composition, a high-voltage gradient can be applied (typically 600 V/cm in 75 microns I.D. and 900 V/cm in 50 microns I.D. capillaries), thus drastically reducing the analysis times. The method is applied to the generation of peptide maps of alpha- and beta-globin chains from human adult hemoglobin. In the case of beta-peptides, at an operative pH of 2.77, which represents a cross-over point in the titration curve of peptides T2 and T9, the two analytes merge into a single peak. However it is shown that it is possible to change the pH of the zwitterionic buffer by adjusting its concentration in solution. In 30 mM Asp (pH 3.0) or 20 mM Asp (pH 3.1) resolution of these two peptides is fully restored. Isoelectric, amphoteric buffers thus seem to represent a novel, powerful buffer system able to offer high resolution and high selectivity.

Probing soft polymeric coatings of a capillary by atomic force microscopy.

Atomic force microscopy (AFM) has been used to probe the surface of a capillary after coating with "soft" polymers, notably polyacrylamides. The aim was the investigation of the efficiency of coverage of the silica surface, so as to reduce or eliminate the electroosmotic flow (EOF), particularly noxious in the separation of macromolecules. The quality of such coating is strongly dependent on two variables: temperature and pH. In the first case, progressively higher temperatures produce open silica patches, where no polymer seems to be bound. The transition from coated to largely uncoated surfaces occurs at 50 degrees C. Also the pH of the polymerizing solution strongly affects the coating efficiency. Since in all coating procedures the monomer solution is not buffered, addition of accelerator (TEMED, N,N,N'N'-tetramethylethylendiamine) induces polymer growth at pH 10-11. These pH values generate hydrolysis of the siloxane bridge anchoring the bifunctional agent (Bind Silane, onto which the polymer chain should grow) to the wall. Thus, coating and de-coating occur simultaneously. Low temperatures during polymer growth (typically 10 degrees C) and buffered solutions (pH 7, titrated after TEMED addition) ensure a most efficient and thorough coating, with virtual elimination of EOF: well coated capillaries exhibit residual EOF values, at pH 10, of the order of 10(-7) cm2 V-1 s-1 vs. a standard value for uncoated capillaries of the order of 10(-4) cm2 V-1 s-1. The AFM data have been fully confirmed by direct measurement of EOF in coated and uncoated capillaries under an electric field.

'Tunable' positive and negative surface charges on a capillary wall: exploiting the Immobiline chemistry.

The Immobiline (weak acrylamido acids and bases) chemistry has been applied to the covalent attachment of a positively (or, if needed, negatively) charged layer onto the inner surface of the silica wall. In particular, the following basic Immobilines have been used: pK 6.2, pK 7.0, pK 8.5 and pK 9.3. In order to avoid pK changes, the charged Immobilines are mixed with neutral acrylamido derivatives (in particular the highly resistant and hydrophilic N-acryloyl aminoethoxyethanol) so as to form a co-polymer having a 1:5 molar ratio (charged to neutral). The mu(eo) vs. pH curves have a slope opposite to that of a naked capillary and fan out on the pH scale following the titration curves of the different weak bases. Such chemistry allows the covalent attachment of charged species having known pK values and offering controlled charged densities on the wall. However, with the atomic force microscope, it is found that such soft coatings (whether charged or neutral) do not seem to provide complete coverage of the surface: naked patches of fused silica are found interdispersed among the polymer-coated ones. A good solution is a hybrid bonded and dynamic coating, obtained by adding short chain linear polyacrylamides to the background electrolyte. Good separations of polycations [poly(L-histidine)] and of histones are reported up to pH 5.7.

On the measurements of electrophoretic mobilities by means of capillary isotachophoresis at a constant voltage.

A method for measuring electrophoretic mobilities by means of isotachophoresis (ITP) at a constant voltage as described by H. Carchon and E. Eggermont (Electrophoresis, 1982, 3, 263-274) is analyzed. An error made in this work, disregarding the pH shift arising at the initial discontinuity on the leader-terminator boundary, has been corrected. This method has been carefully studied and generalized for the presence of constant electroosmotic flow in a capillary. The limits of its applicability and the diffusionless ITP theory in general are discussed. A detailed study of the evolution of initial discontinuity (stationary boundary) showed some anomalies not reported previously, particularly non-monotonic concentration profiles in the vicinity of stationary boundaries. Moreover, in some cases, diffusion effects and the contribution of H+ ions can also strongly influence the behavior of moving boundaries. Computer modelling (confirmed by experimental data) showed that these effects could lead to the decay of the ITP train, despite the fact that the steady state diffusionless ITP theory predicts its stability.

Dependence of the electroosmotic mobility on the applied electric field and its reproducibility in capillary electrophoresis.

Experimental results on the electroosmotic mobility in fused-silica capillaries are presented for different applied voltages and solutions of different pH. The electroosmotic mobility is shown to be dependent on the applied voltage and this dependence cannot be attributed to the temperature effects. Results of the electroosmotic mobility measurements are found to be dependent also on the electrophoresis unit they have been performed in. The explanation given and the relevant theory presented are based on the hypothesis that these effects are produced by a radial electric field inevitably existing in any electrophoresis unit. The concept of the limiting electrophoretic mobility, i.e. extrapolated to the zero applied voltage, is introduced in order to characterize the properties of the solution-wall interface. The slope of the electroosmotic mobility dependence on the applied voltage depends on the solution pH and the surroundings of the capillary. Theoretical estimations agree well with both experimentally found limiting mobilities and slopes. Long-term variations of the electroosmotic mobility are supposed to be related with the cation penetration into the capillary wall.

Quantitative studies of different injection systems in capillary electrophoresis.

For a rigorous assessment of the precise amount of sample loaded, for quantitation purposes, different sample injection systems were evaluated with two commercially available units, Waters Quanta 4000 and Beckman P/ACE 2100. In the first system, sample introduction by hydrostatic means (i.e., placing the sample vial at some height, usually 10.1 cm, above the other capillary end) was evaluated. It was found that in this system there is a constant positive bias, i.e. the amount of sample loaded lies on a curve parallel and above the theoretically predicted loading curve. However, the excess of mass loaded was constant along the injection times explored (covering from 5 to 35 s) and, for a 75 microns capillary, was found to be of the order of +6 nL (above the expected injected value). Thus it is easy to correct for this sample bias. In the electrokinetic mode, a very good correlation between expected and predicted sample loads was obtained for both units. In the pressure system (by positive pressure from a nitrogen tank, Beckman unit) a substantial discrepancy was found between experimental and predicted values (13.5% overload). Since the manufacturer claims a constant pressure of 0.5 psi, i.e. 3447.5 Pa, it would appear that the injection pressure is higher than the given value.(ABSTRACT TRUNCATED AT 250 WORDS)

Left ventricular diastolic function in systemic sclerosis: assessment by radionuclide angiography.

The aim of this study was to assess left ventricular function in subjects with systemic sclerosis. Twenty-four women with systemic sclerosis (mean age 48 +/- 11 yr) and 14 age- and sex-matched normal subjects were studied by radionuclide angiography performed at rest with a temporal resolution of 20 msec/frame. Left ventricular volume curves were generated and indices of systolic and diastolic function were computed. Left ventricular diastolic asynchrony was evaluated by dividing the left ventricle into five regions and then computing the time-to-peak filling rate for each region. After excluding the valvular region, the coefficient of variation of this index was obtained. The isovolumic relaxation period was prolonged in systemic sclerosis patients in comparison to normal subjects (127 +/- 39 msec versus 87 +/- 44 msec, p less than 0.05). Moreover, 38% of the systemic sclerosis patients had a subnormal peak filling rate. Left ventricular diastolic asynchrony was increased in the systemic sclerosis group, as expressed by a higher coefficient of variation of the regional time to peak filling rate (27.9% +/- 11.5% versus 14.5% +/- 8.6%, p less than 0.05). Our results indicate an impaired relaxation and an increased diastolic asynchrony in patients with systemic sclerosis.